Intelligent network Keyboard installation user manual
Contents
1. Three dimensional Joystick 1 3 Technical data operating temperature 10 C 50 C operating humidity lt 90 operating voltage DC12V power supply DW dimensions mm 345x175x98 length x widthx l e height Intelligent keyboard Controller Installation user manual 2 Keyboard installation 2 1 The back view MINI USB Program upgrade USB RS 485 Two lines of RS 485 control Dip switch Reserved for further use RS 232 Reserved for further use Network connection Reserved for further use Power input DC12V 1000mA Power switch 2 2 Installation Connect RS 485 interface on the keyboard with RS 485 interface on camera two equipment A B G separately connect open and start keyboard power Keyboard display user load interface input password then can used Intelligent keyboard Controller Installation user manual 2 3 User guide The first step input keyboard load password default password 000000 then entry main control interface The second step Press SHIFT MENU key entry keyboard setting menu The following steps can operate menu NEXT PREV key move cursor up and down ENTER key insure or enter submenu ESC key return back to upper menu The third step Choose the first term of menu to set communication protocol Choose the second term to set communication baud rate Finish setting and return to the main interface The forth step In2. main interface input address of speed dome camera press CAM key to confirm The fifth step Operate joystick then control the up down left right and zoom of speed dome camera 3 Keyboard Setting 3 1 Setting Please read this chapter carefully and make setting of the keyboard as to it The operation via menu on the LCD screen support both keyboard button control and joystick control Menu for camera site control via joystick excluded 1 Moving the joystick to the left equals pressing the ESC Return to previous menu 2 Moving the joystick to the right equals pressing the ENTER Go to the submenu 3 Moving the joystick up or down equals pressing PREV NEXT and you can select menu option by moving the cursor A The menu will return to the previous level without any operation within 45 sec 5 Contents in lt gt displayed on the LCD screen indicates the button on the keyboard 3 2 Start via Keyboard Keyboard will enter the login option menu after power up without pressing any button In the login menu press SHIFT MENU Jand select camera site controlling log in menu or keyboard function setup log in menu Keyboard Setup Enter Password V1 00 Table 3 1 Keyboard Setup Log in Interface Intelligent keyboard Controller Installation user manual System Keyboard Enter Password V1 00 Table 3 2 Camera Site Controlling Log in Interface 3 3 Log in via Keyboard 1 Enter the 6 digit
3. 2 Alarm Disenable and press ENTER to confirm Alarm Set 1 Alarm Enable Vv 2 Alarm Disenable 3 Set AlarmTriggering Intelligent keyboard Controller Installation user manual Table 4 19 Alarm Trigger Setup Alarm Trigger Setup Move the cursor to item 3 Set AlarmTriggering press ENTER to enter setup Move the cursor to the wanted function and press ENTER to confirm Set AlarmTriggering 1 PRESET SCAN 23 3 TOUR 4 PATTI Table 4 20 Alarm Triggering Setup 14
4. 3 4 3 3 Alarm triggering function nn 13 Intelligent keyboard Controller Installation user manual 1 Keyboard introduction Intelligent network keyboard is designed to directly control high speed low speed PTZ dome camera 1 1 Keyboard main features 3 Axis joystick position exactly Meticulous matrix LCD operate help information plentiful and real time Two wires of RS 485 port can control muli domes Silica gel keystroke back light subarea display durable for using Support self inspection of joystick keyboard LCD port 1 2 Keyboard layout LCD Main board oi 9 Figure amp English input F1 F5 Keys for upgrade ESC Cancel key ENTER Certain key PREV Switch to last dome move the cursor upward on menu NEXT Switch to next dome move the cursor downward on menu PRESET Function key for preset position TOUR Function key for cruising tour position PATTERN Function key for pattern tour position SCAN Function key for auto scan position Intelligent keyboard Controller Installation user manual ALARM Function key for contact closure open close OSD Function key for speed dome s OSD menu setting MENU Function key for keyboard menu setting SHIFT Combination key CLEAR Functiong key for clearing off the inputed instructions CAM Jey for switching camera 3 Lens control key A Iris close B Iris open C Focus near D Focus far E Zoom out F Zoom in
5. OXIC XK5820 Intelligent Keyboard Controller User s Manual Intelligent keyboard Controller Installation user manual Index 1 Keyboard introduction ccccccccececceneeceeeeeeececcceeeeeeeeeesecceeeeeeeseccneeeeeeeeeeeeenenieaeeeeees 1 1 1 Keyboard main features ccccccceceeeceeeeeneaeeeceeeeeeseeeeaaeeteeeesseneaeeeseesesssesseeaees 1 1 2 Keyboard E e TE 1 1 3 Technical Parameters nn 2 2 Keyboard Imstallatton ekre teertetttttttrtttttt rttr tnet tetE ttnn nariuinnnane rarr errrrnnne eene 2 2 1 The back View ae are He es a aiana riada 2 2 2 Instalati EE 3 ge UU TE A 3 Keyboard SettiMg WEE A 3A SE 11 ao DEE A 3 2 Start keyboard een einen ernennen ach nee 4 3 3 Load keyboard nu nenne ee ee ud 5 3 4 Keyboard function men 5 SE ET d PrOltOCOl E 5 34 2 Set baud rate aussen nei 6 E 6 3 4 4 Set password E 6 SEET een ae ed e 6 3 4 6 Keystoke test einen eee 7 3 4 7 Set joystick Calibration nennen 7 KEE 7 4 Normal Operation ek deed ae een 8 4 1 Camera Set control u ee ein 8 4 2 Keyboard shortcuts Control 8 4 2 1 Switch HIR HI en 9 4 2 2 Operate dome menu function nn 9 4 2 3 AUX CONTO EE 9 4 2 4 Present fUNCHION sissien neiisnnisienna anniina naaa iaiaaeaia AREN anaE 9 We TR ue 10 4 2 6 Auto present tour hunchon anne 11 4 2 7 Pattern tour funchon ern 11 4 3 Pan Tilt function MENU nn 12 4 3 1 Auto flip function ET 12 4 3 2 Home position function nenn nannnnnrnnnn en 1
6. R Presets Table 4 12 Cruising Track Presets Setup 4 2 7 Pattern Tour Press and hold PATTERN for 1 second to enter Input the wanted pattern tour number Press PATTERN to start Press SHIFT PATTERN to stop the pattern tour Press ENTER to enter setup 11 Intelligent keyboard Controller Installation user manual PATTERN Function No 1 Press lt PATTERN gt to Cala Press lt ENTER gt to Set Table 4 13 Pattern Tour Operation Pattern Tour Setup Move the cursor to item 1 Start press ENTER Ito start setup The PTZ movements will be recorded End Pattern Tour Move the cursor to item press ENTER to end ERN 1 Function Set 1 Start 2 SEOP Table 4 14 Pattern Tour Setup 4 3 PTZ Function Menu Under main menu press MENU to enter PTZ function setup Move joystick downward or press NEXT to move the cursor downward Move the joystick upward or press RPEV to move the cursor upward Move the joystick rightward or press ENTER to enter submenu move the joystick leftward or press ESC to go back to previous menu Dome Setup 1 PRESET Set SCAN Set TOUR Set PATTERN Set Flip Set Home Set Alarm Set Table 4 15 PTZ Function Setup For functions of preset scan tours and pattern please refer to chapter 4 2 4 3 1 Auto Flip Move the cursor to item 5 Flip Set press ENTER to enter Auto Flip setup Open Auto Fl
7. TER to the value setup status Enter value Unit Minute and press ENTER Lock delay time setup Move the cursor to option and press ENTER to value setup status Enter value Unit Minute and press ENTER DelayTime Set 1 BlackLight 2 30M 2 SleepTime 2 30M Table 3 10 Delay Time Setup Interface 4 Regular Operation Keyboard controls high speed PTZ directly and realizes scene positioning functions like upward downward left right moving zoom in out focus and iris via RS 485bus Functions as PTZ preset position setup and calling auto scanning cursing track and pattern tour are also supported The camera site controlling log in interface is the default interface when keyboard starts 4 1 Camera Site Controlling Log in Enter the password in the camera site controlling log in interface and press ENTER The factory default password is 000000 Please modify the password System Keyboard Enter Password V1 00 Table 4 1 Camera Site Controlling Log in Interface 4 2 Shortcut Controlling Operation Enter the correct password to the main camera site controlling interface Camera No 001 Baudrate 9600bps Protocol PELCO P Press lt MENU gt Enter Setup Table 4 2 Camera Site Controlling Interface Intelligent keyboard Controller Installation user manual PTZ Scene Positioning Function In the main controlling interface up downileft right moving of
8. ip Move the cursor to item 1 Flip ON press ENTER to confirm Close Auto Flip Move the cursor to item 2 Flip OFF press ENTER to confirm 12 Intelligent keyboard Controller Installation user manual Flip Set 1 Flip ON 2 Flip OFF Table 4 16 Auto Flip Setup Menu 4 3 2 Home Position Move the cursor to item 6 Home Set press ENTER to enter home position function setup Open guard location Move the cursor to item 1 Home Open press ENTER to confirm Close home position Move the cursor to item 2 Home Close press ENTER to confirm Home Position Idle Time Setup Move the cursor to item 3 Idle Time 1 4Min press ENTER to enter value Input value and press ENTER to confirm Home Set 1 Home Open 2 Home Close 3 Idle Time 1 4Min 4 Set Home Triggering Table 4 17 Home Position Setup Menu Home Position Triggering Setup Move the cursor to item 4 Set Home Triggering press ENTER to enter home triggering setup Move the cursor to the wanted function and press ENTER to confirm Set Home Triggering 1 PRESET Vv 2 SCAN 3 TOUR 4 PATTI Table 4 18 Home Position Function Setup 4 3 3 Alarm Triggering Move the cursor to item 7 Alarm Set press ENTER to enter alarm triggering setup Open Alarm Triggering Move the cursor to item 1 Alarm Enable and press ENTER to confirm Close Alarm Triggering Move the cursor to item
9. o setas andpress ENTER Baudrate 1 2400bps 2 4800bps 3 9600bps Table 3 4 Baudrate Setup Interface 3 4 3 Keyboard Voice Setup Keyboard Voice Setup Move the cursor to item3 Voice On Off and press ENTER to the keyboard voice setup interface Open the voice Move the cursor to item1 Voice On and ENTER Shut the voice Move the cursor to item2 Voice Off and press ENTER Voice On Off 1 Voice On 2 Voice Off Table 3 5 Keyboard Voice Setup Interface 3 4 4 Password Management Modify Password Move the cursor to item4 Set Password and press ENTER to password modification interface in which the user can modify the log in password Enter the correct password first and create the new password later The same new password should be entered twice The keyboard will save the new password and log off automatically after the user presses ENTER Change Password Original Password New Password Confirm Password Table 3 6 Password Modification Interface 3 4 5 LCD Setup Grey scale setup of LCD Move the cursor to item5 LCD Adjust and press ENTER Ito the LCD setup interface Press NEXT Jor PREV to adjust the grey scale of LCD display Setup data will be saved automatically when logging off 6 Intelligent keyboard Controller Installation user manual LCD Adjust Press lt PRE Table 3 7 LCD Setup 3 4 6 Keyboard Button Test Keyboard Button Tes
10. password and press ENTER to log in 2 About the password the default password is 000000 Please modify the password 3 4 Menu for Keyboard Function Setup Set Protocol Set the PTZ control protocol Set Baudrate Set communication protocol Baud rate Voice On Off Set the keyboard voice as on or off Set Password Change the grey scale of the LCD display LCD Adjust Modify the keyboard log in password Keyboard Test Test the validity of the keyboard buttons Joystick Calibrate Correct the central value of the joystick Black Light Set the off delay time of the keyboard backlight Unit Minute Delay Time Set Sleep Time Set the keyboard sleep delay time CUnit Minute 3 4 1 Protocol Setup Set keyboard communication protocol Move the cursor to option Set Protocol and press ENTER to the communication protocol setup interface This keyboard supports 3 protocols PELCO P PELCO D TIDNDY Setup Move the cursor to the protocol you want to set as and press ENTER Set Protocol 1 PELCO P 2 PELCO D 3 TIANDY Table 3 3 Communication Protocol Setup Interface Intelligent keyboard Controller Installation user manual 3 4 2 Baudrate Setup Communication baudrate setup move the cursor to option 2 Set Baudrate and press ENTER to the baudrate setup interface This keyboard supports 4 protocols 2400bps 4800bps 9600bps 19200bps Setup Move the cursor to the bandrate you want t
11. t Use joystick to define the left limit press ENTER to confirm Set auto scan right limit move the cursor to item 1 right Use joystick to define the right limit press ENTER to confirm Auto scan speed setup move the cursor to item 3 Speed press ENTER and input the value of the speed press ENTER to confirm SCAN 1 Function Set 1 Left 2 Right 3 Speed Table 4 9 Auto Scan Setting 10 Intelligent keyboard Controller Installation user manual SCAN 1 Function Set SCAN Speed Speed Level 1 30 20 Table 4 9 Auto Scan Speed Setup 4 2 6 Cruising Track Press and hold TOUR for 1 second to enter Input the wanted tour number press TOUR then it will start the tour Press SHIFT TOUR to stop the tour press ENTER to enter setup TOUR Function No 1 Press lt TOUR gt to Cal Press lt ENTER gt to Set Table 4 10 Cruising Track Operation Tour intervals setup move the cursor to item 1 Interval 1 60Sec press ENTER to enter input value and press ENTER to confirm Cruising Track Presets Setup move the cursor to item 2 press ENTER to enter There could be up to 11 presets for each Cruising track Input the wanted presets number Press NEXT to switch to the next preset and PREV to the previous one TOUR 1 Function Set 1 Interval 1 60Sec 2 Add TOUR Presets Table 4 11 Cruising Track Setup TOUR 1 Function Set Add TOU
12. t Move the cursor to item6 Keyboard Test and press ENTER to the keyboard button test interface The LCD screen will display name of the current pressed button when the user presses a button Test SHIFT J button by pressing SHIFTJ 11 Press SHIFT ESC to log off Keyboard Test Push Key Key Name lt SHIFT ESC gt gt EXIT Table 3 8 Keyboard Test Interface 3 4 7 Joystick Correction Joystick Correction Move the cursor to item7 Joystick Calibrate and press ENTER to the joystick correction interface Leave the joystick to the center position and press ENTER to correct the position again Setup data will be saved automatically when logging off The joystick has been corrected in the factory and users can use it without adjustment The parameters of the joystick may be effected due to different operating environment and users can restore the accuracy by correction Joystick Calibrate Joystick is free then Press lt ENTER gt Table 3 9 Joystick Correction Interface 3 4 8 Delay Time Setup Keyboard supports automatic lock in controlling interface status Keyboard will switch to lock status without any operating within the delay time Intelligent keyboard Controller Installation user manual Delay time setup Move the cursor to item8 Delay Time Set and press ENTER to delay time setup interface Button backlight delay time setup Move the cursor to option and press EN
13. the joystick can realize controlling of PTZ the speed of which can be subdivided to level 0 63 Clockwise rotation is for zooming our and counterclockwise rotation is for zooming in Iris controlling can be realized via iris function button and please refer to the first chapter as to the iris controlling function button definition 4 2 1 PTZ Switching Enter the PTZ No you want to switch to and press CAM This PTZ No will be set as the current position of the keyboard 4 2 2 OSD Menu for Controlling Camera In the main controlling interface press OSD to the OSD menu or calling preset No 95 As to the OSD menu operation please refer to the speed dome camera user s manual 4 2 3 Auxiliary Switching Controlling In the main controlling interface press ALARM Ito the auxiliary switching controlling interface Enter the auxiliary switch serial numbers 1 8 available you need to control Press ALARM lto open auxiliary switch and SHIFT f ALARM lto shut auxiliary switch RELAY No 1 Press lt ALARM gt Open Press lt SHIFT ALARM gt Close Table 4 3 Auxiliary switch operation 4 2 4 Preset Press and hold PRESET key for 1 second The LCD will display as the table 4 4 shows To call a preset position just input the preset number and press PRESET key To set a preset position just input the preset number and press ENTER key then you can set the preset position Pressing NEXT key will add 1 to preset n
14. umber while pressing PREV key will subtract 1 from the preset number PRESET Function No 001 Press lt PRESET gt to Call Press lt ENTER gt to Set Table 4 4 Preset Function Setup Preset Setup Press NEXT PREV to move the cursor to item 1 Set Intelligent keyboard Controller Installation user manual PRESET use the joystick to define the wanted position and press ENTER Set a Title for a Preset Move the cursor to item 2 2 Set PRESET Title press ENTER then you can set the title The title can be English words or figures press CAM to switch Press CLEAR to delete After the input press ENTER to confirm Please note Title setup function is only supported by TIANDY protocol ESET 001 Function Set 1 Set PRESET 2 Set PRESET Title Table 4 5 Preset Setup PRESET 001 Function Set PRESET Label Type ABC lt CAM gt Switch lt gt Table 4 6 Preset Title Setup 4 2 5 Auto Scan Press and hold SCAN key for 1 second The LED shows the auto scan function setup Input the wanted auto scan number press SCAN it will start the auto scan Press SHIFT SCAN to stop Press ENTRE to enter the auto scan setup SCAN Function No 1 Press lt SCAN gt to Call Press lt ENTER gt to Set Table 4 7 Auto Scan Set auto scan left limit move the cursor to item 1 Lef
Download Pdf Manuals
Related Search