LHFS 590 User manual
Contents
1. the loading off at the end of setting The load will remain ON until the last movement is detected The a mark is used for installation test Sets the sensitivity of the microwave motion sensor Turing this knob counterclockwise will decrease the sensitivity and detecting range of motion sensor clockwise will increase the sensitivity and detecting range 10 500 Sets the values of ambient light When the values which be detected by photodiod less than the setting the detector will become activity Sz otherwise it enter standby mode Clockwise the knob to mark the sensor detection will always be enbaled SENSOR STATUS Warm up LED indicator ON Loading ON This unit requires a warm up of approx 30 seconds after power i applied forthe system s circuit to stabilize Test Mode LED indicator ON Loading ON Counterclockwise rotate the GED adjustment knob tof the sensor will enter the TEST mode each time motion is detected the load will be ON 2 seconds ONLY then delay 2 seconds for next time detection Clockwise rotation the GED adjustment knob to any position of 1 30 wil exit the test mode Stand by LED indicator OFF Loading OFF Inthe non test mode if the sensors detect ambient light level is higher than the adjustment knob settings it will enter standby mode Automatic Mode LED indicator Fast ash twice each detection Loading Auto ON OFF In the non test mode if the sensors dete2. FETIME WARRANTY 3 YEARS GUARANTEE This product is warranted to be free from defects in material and workmanship for ife of product Ifa defect occurs call your suppliers for instructions on how to have defective product repaired or replaced free of charge LIMITATIONS This warranty only covers assembled sensor products and snot extended to other components Lamp Bulbs or equipment used onthe product Waranty extends to original purchaser of product Receipt or other approved proof of purchase required for waranty service NOT LIABLE FOR INCIDENTAL INDIRECT OR CONSEQUENTIAL DAMAGES Some states do not allow the exclusion or limitation of incidental or consequential damages so the above imitation or exclusion may not apply to you This waranty gives you specific legal rights and you may also have other rights which vary from state to state NOT COVERED Product failure not relating to faulty material or workmanship comosion of brass components reimbursement for installation or unauthorized TIPS 1 Appropriate to increase the delay time can effectively extending the life ofthe produc 2 The emission power of this microwave sensor is less than 0 2m only 1 5000 ofthe GSM mobile phone or electric stove long term use will NOT ause harm to human animal or plant SEOCUMEAGY tarion aon
3. Microwave Motion SENSOR LHFS 590 User manual Congratulations on your purchase of our microwave motion sensor produc You have purchased a safe dependable and easy to install security sensor system This product can be widely used in offices underground garages buildings comidor stoop washroom and so on Carefully read the user manual thoroughly before using NOTICE THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH ALL APPLICABLE INSTALLATION CODES 1 IF YOU ARE NOT FAMILIAR WITH ELECTRICAL WIRING IT IS RECOMMENDED THAT YOU SECURE THE SERVICES OF A WELL QUALIFIED ELECTRICIAN WHO CAN ASSURE THAT THIS INSTALLATION MEETS LOCAL STATE AND NATIONAL coves 2 BE SURE POWER IS TURNED OFF AT THE MAIN POWER PANEL OR FUSE BOX PRIOR TO INSTALLATION OR REPLACING SENSOR 3 The sensor is for indoor use ONLY 4 The sensor is suitable for dry locations 5 A type C circuit breaker 6A250VAC according to EN60898 1 shall be installed in the fixed wiring for protection 6 The electrical system and the method of connecting the sensor to the system must be in accordance with local state and national electric codes 7 This sensor is to be connected to a 23010 volt 50 or 60 Hz power source Connecting to a different power source may create a hazard and will void the warranty 8 Never use a lamp lading with a higher wattage than the stated maximum allowed on the sensor Using a higher wattage loading may cause a fie hazard and or dam
4. age to the unit 9 Do not attempt to open the unit housing There are no serviceable parts inside SPECIFICATIONS RATING 23010 VAC 50 6082 STANDBY POWER approx 0 6W 5 8GHz 75MHz CW RADAR ISM BAND MICROWAVE FREQUENCY TRANSMITTER POWER lt 0 2mW USE LOCATIONS INDOOR USE ONLY CEILING or WALL MOUNTING MOUNTING HEIGHT FOR CEILING 25m FOR WALL 125m DETECTING ANGIE FOR CEILING 360deg FOR WALL 180deg DETECTING DISTANCE 02 8m FOR WALL 3 12m AMBIENT LIGHT CONTROL 10 Lux ADJUSTABLE TIME DELAY 1 30 MINUTES w TEST MODE MANUAL OVERRIDE HOURS SWITCH TYPE RELAY LOAD CAPACITY 108 277VAC OPERATING TEMPERATURE 0 460 C FULL LOAD 70 C 60 LOAD STORAGE TEMPERATURE 20 80 C 10 95 RH MAXIMUM LOAD INCANDESCENT 1000W HALOGN 500W LV HALOGN 200w FLUORSCENT 5 OR 160W 20uF Max ENERGY SAVE LAMP 200W CFL amp PL LEDs LAMP 200W 385mm wa HOW TO WIRE BE SURE POWER IS TURNED OFF AT THE MAIN POWER PANEL OR FUSE BOX PRIOR TO INSTALLATION OR REPLACING MICROWAVE MOTION SENSOR Please following the below steps to wiring Pi STEP 1 Open the cover according to the arrow marked aeforeinstaling C STEP 2 Put the power wire into the corresponding wiring hole on the side of motion sensor CULN then tighten with screwdriver Tips make sure that the stripping length of wir
5. ct ambient light level is less than the adjustment knob settings the auto motion detecting wil be activated Manual Override LED indicator Interval 5 seconds flash 1 time Loading ON Flip the power switch f applicable OFF and then ON twice within 2 seconds this will put the sensor into Manual Override status which means the light will be ON and auto OFF after 4 hours or tum OFF the sensors power switch and then ON again within 2 seconds to place the sensor back to AUTOMATIC status FAQ Q1 Does not function at all Make sure the power switch if applicable is ON and check the wiring is correct Check that the circuit breaker fuse and main circuit breaker or main power switch are ON Check that the loading such as light bulb is functional The ambient light level is higher than settings if necessary may be appropriate to increase the set value of Q2 The sensor light is always ON The setting of delay time is too long if necessary may be appropriate to reduce the set value of The sensor is in the Manual Overie state turn OFF the sensors power switch and then ON again within 2 seconds to place the sensor back to AUTOMATIC status The sensor be installed on movable andor frequent vibrations of objects please change the sensors mounting location Ifthe sensor be installed in the fixture with fluorescent tube or CFUPL lamp try to appropriate to reduce the set value of D LIMITED LI
6. e must be between 3 to Sm Philip screw driver CL Controled Live wireloutput L Live wirlinput N Neutral wireinput output Wire pee STEP 3 Put the cover back after wiring WIRING DIAGRAM N Neutral wire The microwave motion sensor can be installed in the ceiling lighting fixture but 1 Do NOT install the sensor in a dosed space made of metal 2 Avoid mount the sensor place 3 Be aware of the temperature inside lamp housing should be lower than 60 C 4 Itis recommended to mount the sensor on the material of plastic wood or PVC instead of metal if the lamp is made of diferent materials 5 Ensure the sensor is far awaylat least 60mm from the ballast lamp hold or filament pem Lap holder Balast yet and shaking Mizowave Sensor Microwave Sensor Balast gt 60mm gt 60mm Lamp holder HOW TO SETTING HES 580C series have three VR knobs to control the connected electrical appliance which can be automatically tum ON or tum OFF according to setting value 1 Ambient illumination detector Photodiod 2 Indicator Red LED 3 QLD Time setting knob 4 GED Sensitivity setting knob 5 Ambient fight setting knob Sets how long the loading will stay on after motion is detected between 1 to 30 minutes Turing the knob will change time duration Every time motion is detected the timer will restart and turn
Download Pdf Manuals
Related Search