Nefton Technologies - Mettler Toledo Panther Terminal User's Guide
Contents
1. A setpoint is a target value that you can use to stop a feeding or discharging device When the weight on the scale exceeds the setpoint value the setpoint output is turned off In addition to the setpoint values the PANTHER terminal provides the ability to enter and use preact values Preact is used to anticipate the amount of material which may be between the feeder and the scale when the feeder is turned off or may be used to anticipate the reaction time of the feeder or gate A zero tolerance value is also available This can be used as a control check to make sure the hopper or scale has returned to within a preset tolerance of zero before the next operation may begin The setpoint mode of operation must be enabled during setup Refer to the PANTHER Terminal Technical Manual for details With the scale in the normal operating mode press the Memory key The display shows SP1 0 indicating that you do NOT wish to enter or adjust the first setpoint value Press the Transact Print key if you do NOT wish to enter or adjust this setpoint value and to proceed fo the next step adjusting the value of the next setpoint OR Press the Select key to change the display to SP1 1 indicating that you DO wish to enter or adjust the first setpoint value Press the Transact Print key to verify your selection or press the Select key to change the response back to a O or no The display will now show the current value stored as setpoi2. la aux norme s ou au x document s normatif s Al que se refiere esta declaraci n es conforme a la s norma s u otro s documento s normativo s Waarnaar deze verklaring verwijst aan de volende norm en of richtlijn en beantwoordt A cui si riferisce questa dichiarazione conforme alla e sequente i norma e o documento i normativo i in combination with a weighing platform produced by Mettler Toledo is in conformity with the following directives and standards Council directive on the harmonization of the laws of the Member states standards relating to non automatic weighing instruments 90 384 EEC amended by directive EN 45501 1992 93 68 EEC relating to electromagnetic compatibility 89 336 EEC amended by directive EN 55022 B 93 68 EEC 92 31 EEC EN 50082 2 relating to electrical equipment designed for use within certain voltage limits EN 60950 73 23 EEC amended by directive 93 68 EEC Worthington Ohio USA November 2000 Mettler Toledo Inc Darrell Flocken Manager Weights amp Measures Office of Weights and Measures Original issue January 1997 Revised February 1997 added compliance to Non automatic Weighing Instrument Directive November 2000 added compliance to Heavy Industrial Immunity EN 50082 2 According to EN 45014 INTRODUCTION This publication is provided solely as a guide for individuals who have received Technical Training in servicing the METTLER TOL
3. Refer to the following diagram when installing the panel mount terminal AN 9 NY 4 0 188 dia 3 16 E O H drill holes n Y A 159 3 ici rr roe i 6 26 Jc a00000t Ion 0000000 00 91 9 1361 68 6 3 62 ree 2 70 e ToT 8 k 171 5 80 8 69 8 6 75 3 18 2 75 La 157 5 6 20 m i 112 6 L o 132 0 5 20 4 M4 x 20 mm stainless steel BER studs with nuts provided Y 16 84 Y 6 63 PANTHER METTLER TOLEDO 9999989 e hb kg B 5 20 575 2 0 lt G NT PT T 4 02 1 5 METTLER TOLEDO PANTHER Terminal User s Guide Power Requirements Controller PCB 1 6 Temperature and Humidity 4 02 The PANTHER terminal is provided with a universal power supply which operates from 85 to 264 VAC and with a line frequency of 49 to 63 Hz Power consumption is 12 Watts maximum Power is applied via a terminal strip on the panel mount version or a permanently attached line cord on harsh enclosure version The integrity of the power ground is important for safety and dependa
4. 100004 rating and approval AM 5162 was issued by statutory authority of the Minister of Industry Science and Technology of Canada The PANTHER terminal was submitted for approval to The Nederlands Meetindtituut NMi in the Netherlands After evaluation the PANTHER terminal was found to meet and or exceed the requirements for a Class 5000 division and a Class 1000 division weighing instrument The NMi issued EC type approval certificate TC2969 Rev 4 in accordance to Council Directive 90 384 EEC on Non automatic Weighing Instruments The PANTHER terminal was submitted for approval to National Standards Commission NSC in Australia After evaluation the PANTHER terminal was found to meet and or exceed requirements for Class Ill 3000d rating and a Supplementary Certificate of Approval 5353 was issued by the NSC in accordance to DOCUMENT 100 for Non automatic Weighing Instruments The PANTHER terminal meets or exceeds FCC docket 80 284 for conducted and radiated emissions requirements as a Class A digital device Radio Frequency Interference Susceptibility AC Power Line Voltage Variation Chapter 1 Introduction Standards Compliance The PANTHER terminal meets USA Canadian and EC requirements for RFI susceptibility as listed in the following table with a maximum of one display increment of change when calibrated for recommended builds RFI Susceptibility Radio reference Transmitted Power at Field Strength Frequency
5. Fax 210 6654545 marketing nefton gr www nefton gr
6. ROM ERROR Cycle power Check power supply voltages Replace Main Logic PCB INTERNAL MATH ERROR Press CLEAR to acknowledge Unit will reset SETPOINT VALUE 7 FOR CALIBRATION TEST WEIGHT EXCEEDS 105 OF Use less than 105 of capacity CAPACITY Press CLEAR and re enter SPAN CALIBRATION ERROR Recalibrate If error persists check programming or replace load cell ANALOG LOAD CELL OUT OF RANGE Recalibrate Replace load cell E50 WEIGHT CAN NOT BE DISPLAYED IN Some alternate units combinations are illegal Choose another scale build or ALTERNATE UNITS disable alternate units EEE POSITIVE MORE THAN ZERO CAPTURE Remove material from scale base Disable AZM in setup Cycle power LIMIT OF 2 OF SCALE CAPACITY EEE NEGATIVE MORE THAN ZERO Disable AZM in setup Calibrate scale Cycle power CAPTURE LIMIT OF 2 OF SCALE CAPACITY NO ANALOG LOAD CELL DETECTED Check load cell wiring Replace load cell Replace Main PCB 3 2 4 02 ne7 ton Zuy on Innavon ZULLOPQWON METTLER TOLEDO 1900 Polaris Parkway Columbus Ohio 43240 Phone US and Canada 800 786 0038 614 438 4511 Phone International 614 438 4888 www mt com P N D14945800A 4 02 METTLER TOLEDO and PANTHER are registered trademarks of Mettler Toledo Inc 2002 Mettler Toledo Inc Printed in U S A D14945800A Nevtwv TexvoAoyieg ABEE 113 T 0 67934 15344 210 6654544
7. the current value stored as the high zone value The most significant digit blinks indicating it may be adjusted To move the active digit to the right use the Memory key A small right arrow appears below the key To move the active digit to the left use the Tare key A small left arrow appears below the key 4 02 2 7 METTLER TOLEDO PANTHER Terminal User s Guide 2 8 4 02 s El Te El Te To increase the value of the flashing digit for example to change from O to 1 use the Select key Use these keys to change the digits representing the high zone value You may use the Memory move right and Tare move leff keys and the Select increase number key in any combination you wish When the proper high zone value is displayed press the Transact Print key to accept your entry F5 8 2 xx is now displayed indicating the current high accept zone value If you wish to adjust this value follow steps 16 20 as described above Otherwise press the Transact Print key to move on to the next step F5 8 3 xx is now displayed indicating the current low accept zone value If you wish to adjust this value follow the steps described above Otherwise press the Transact Print key to move on to the next step F5 8 4 xx is now displayed indicating the current low zone value If you wish to adjust this value follow the steps described above Otherwise press the Transact Print key to retur
8. weight of the objects on the scale platform The Memory key is used to access setpoint or target weight values Operator access to these values must be enabled in the set up mode Refer to the advanced operation section for details on how to change these values The Select key allows the operator to switch between the primary and secondary weighing units To change weighing units press this button Each initiation of this button will either switch the display units from the primary to the secondary units or back to the primary from the secondary A cursor will change indicating which units are being displayed This key is also used in the setup and programming modes to select between yes and no replies and to change displayed values The Transact Print key is used fo initiate a serial output of the weight data To request this transmission of data press this button The actual format of the data string is determined in set up This key is also used to accept a response to a setup or programming question 4 02 2 1 METTLER TOLEDO PANTHER Terminal User s Guide Operator Functions Zero the Scale If the scale platform is empty and the NET cursor is NOT lit press the zero button to compensate for any material which may be on the scale platform The zero button is 30 limited to compensating weight that is between 2 or 20 if programmed accordingly of the scale s weighing capacity Tare Operations To determine the weig
9. EDO product Information regarding METTLER TOLEDO Technical Training may be obtained by writing to METTLER TOLEDO 1900 Polaris Parkway Columbus Ohio 43240 Phone US and Canada 614 438 4511 Phone International 614 438 4888 FCC Notice This device complies with Part 15 of the FCC Rules and the Radio Interference Requirements of the Canadian Department of Communications Operation is subject fo the following conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense This manual correctly describes the operation and functionality of the PANTHER terminal containing software versions as follows The software number is displayed during the power up seque
10. EQUIPMENT AND OR BODILY HARM CAUTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES WARNING IN ORDER TO USE THE PANTHER PANEL MOUNT TERMINAL IN AN AREA CLASSIFIED AS CLASS II AND 111 DIVISION 2 GROUPS A B C D FOR G METTLER TOLEDO CONTROL DRAWING 155907R MUST BE FOLLOWED WITHOUT EXCEPTION FAILURE TO DO SO COULD RESULT IN BODILY HARM AND OR PROPERTY DAMAGE 2 WARNING THE PANTHER TERMINAL IS NOT INTRINSICALLY SAFE DO NOT USE WITHIN AREAS CLASSIFIED AS HAZARDOUS DIVISION 1 OR ZONE 0 1 BECAUSE OF COMBUSTIBLE OR EXPLOSIVE ATMOSPHERES AN WARNING WHEN THIS EQUIPMENT IS INCLUDED AS A COMPONENT PART OF A SYSTEM THE RESULTING DESIGN MUST BE REVIEWED BY QUALIFIED PERSONNEL WHO ARE FAMILIAR WITH THE CONSTRUCTION AND OEPRATION OF ALL COMPONENTS IN THE SYSTEM AND THE POTENTIAL HAZARDS INVOLVED FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT IN BODILY HARM AND OR PROPERTY DAMAGE AN WARNING IF THIS DEVICE IS USED IN AN AUTOMATIC OR MANUAL FILLING CYCLE ALL USERS MUST PROVIDE A HARD WIRED EMERGENCY STOP CIRCUIT OUTSIDE THE DEVICE CIRCUITRY FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT IN BODILY INJURY AND OR PROPERTY DAMAGE CONTENTS INTOQUENON Pc M EE 1 1 OVErVieW RRRRRRRRRRRRRRRRRREEMMMEEEEEEEEEEEEEEEEEEEEEEEEEEEMEEEEEEEEEMEEEMEMMMS 1 1 Standard ts ios teet LO ts 1 2 Optional F
11. PANTHER Terminal User s Guide D14945800A 4 02 Mettler Toledo Inc 2002 No part of this manual may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying and recording for any purpose without the express written permission of Mettler Toledo Inc U S Government Restricted Rights This documentation is furnished with Restricted Rights GY METTLER 7 TOLEDO CUSTOMER FEEDBACK Your feedback is important to us If you have a problem with this product or just a suggestion on how we can serve you better please fill out this form and send it fo us If you are in the United States you can mail this postpaid form to the address on the reverse or fax it to 614 438 4355 If you are outside the United States please apply the appropriate amount of postage before mailing You can also send your feedback via email to quality feedback miwt mt com Your Name Date Organization Name Address Phone Number _ Fax Number _ E mail Address How well did this product meet your Comments expectations in its intended use Met and exceeded my needs Met all needs Met most needs Met some needs Did not meet my needs PROBLEM UNACCEPTABLE DELIVERY OUT OF BOX ERROR Shipped late Wrong item Wrong documentation Shipped early Wrong part Missing documentation Shipped to incorrect location Missing equipment Incorrectly calibrated Other Please Specify Equipment fai
12. STMENTS THAT MUST BE MADE WITH POWER ON FAILING TO OBSERVE THESE PRECAUTIONS CAN RESULT IN BODILY HARM AND OR PROPERTY DAMAGE Information on installing programming and servicing the PANTHER terminal is found in the PANTHER Terminal Technical Manual Only qualified personnel should perform installation programming and service Please contact your local METTLER TOLEDO representative for assistance 4 02 3 1 METTLER TOLEDO PANTHER Terminal User s Guide Error Codes AN WARNING ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THE TERMINAL EXERCISE CARE WHEN MAKING CHECKS TESTS AND ADJUSTMENTS THAT MUST BE MADE WITH POWER ON FAILING TO OBSERVE THESE PRECAUTIONS CAN RESULT IN BODILY HARM AND OR PROPERTY DAMAGE The following errors codes can be used as a reference should you encounter problems when using the PANTHER terminal Please remember that qualified personnel should perform all service and maintenance Error Description Corrective Measures PROGRAM MEMORY ERROR Check power supply voltages Replace Main Logic PCB INTERNAL RAM ERROR Check power supply voltages Replace Main Logic PCB E3 EEPROM MEMORY ERROR Press the Clear key Check power supply voltages Reprogram Recalibrate Replace Main Logic PCB ANALOG LOAD CELL CONNECTED power supply voltages Replace Main Logic PCB ERROR Replace Main Logic PCB DigiTOL LOAD CELL RAM ERROR Cycle power Check power supply voltages Replace load cell DigiTOL LOAD CELL
13. Specified Distance 3 volts meter 4 Watts at 2 meters The PANTHER terminal meets NIST H 44 Canadian Gazette Part 1 and OIML SP7 SP2 line voltage variation specifications as listed in the following table AC Power Line Voltages Specification AC Line Voltage Line Frequency in Hz Line Voltage Variation Minimum Nominal Maximum 4 02 1 9 METTLER TOLEDO PANTHER Terminal User s Guide NOTES 1 10 4 02 Chapter 2 PANTHER Terminal Operations PANTHER Keypad PANTHER Terminal Operations This chapter provides general information that an operator will need to become familiar with the terminal and to perform its functions PANTHER Keypad 0 gt The Zero keys are used to compensate for small changes weight when the scale platform is empty These changes in weight are most often caused by material spilling onto the weighing platform To zero the indication of weight press this button The Tare key is used to subtract the weight of the object on the scale platform from subsequent indications of weight This is most often the weight of an empty container Once this value is fared the indication of weight will change to indicate net weight To tare the scale place an empty container on the scale and press this button The Clear key is used to clear a previously entered tare value To clear the tare value press this button The indication of weight will return to the gross mode showing the total
14. ble operation of the terminal and its associated scale base A poor ground can result in an unsafe condition if an electrical short develops in the equipment A good ground connection assures extraneous electrical noise pulses are minimized The power line for the PANTHER must not be shared with equipment such as motors relays or heaters that generate line noise To confirm ground integrity a commercial branch circuit analyzer like an ICE model SureTest ST 1D or equivalent is recommended This instrument uses a high amperage pulse to check ground resistance It measures the voltage from the neutral wire to the ground connection and will provide an assessment of the line loading Instructions with the instrument provide guidelines about limits that assure good connections Visual inspections and a query of the user will provide information about equipment sharing the power line If adverse power conditions exist a dedicated power circuit or power line conditioner may be required When the PANTHER panel mount terminal is installed within an enclosure which resides within an area classified as Division 2 special AC wiring requirements must be met These requirements are shown on METTLER TOLEDO control drawing 155907R in the PANTHER Panel Mount Terminal Division 2 Installation Guide 15791600A The PANTHER terminal has one discrete input and three discrete outputs 5 Volts DC Each discrete output can sink up to 20 mA maximum The maximum curren
15. dcoating to resist damage to the lens The harsh environment PANTHER terminal enclosure is designed as dust tight and splash proof enclosure The keyboard display enclosure for the panel mount version is certified TYPE 4 4X and 12 requirements for dust tight and splash proof applications when properly installed in an appropriate enclosure The rest of the panel mount enclosure meets TYPE 1 requirements and provides no protection against dust or water ingress The PANTHER panel mount terminal has been approved by Factory Mutual for use in areas classified as Class Il and Ill Division 2 Groups A B C D F and G when installed in a dust tight enclosure and connected per METTLER TOLEDO control drawing 155907R The PANTHER panel mount terminal has been approved by Factory Mutual for use in areas classified as Class Il and Ill Division 2 Groups A B C D F and G when installed in a National Testing Laboratory approved dust tight enclosure and connected per METTLER TOLEDO control drawing 155907R Refer to the PANTHER Panel Mount Terminal Division 2 Installation Guide 157916004 for additional details WARNING TO USE THE PANTHER PANEL MOUNT TERMINAL IN AN AREA CLASSIFIED AS CLASS I II AND III DIVISION 2 GROUPS A B C D F OR G METTLER TOLEDO CONTROL DRAWING 155907R MUST BE FOLLOWED WITHOUT EXCEPTION FAILURE TO DO SO COULD RESULT IN BODILY HARM AND OR PROPERTY DAMAGE The PANTHER terminal is not intrinsically safe but i
16. eatures 1 4 SDECHILAIIONS ee 1 5 Standards Compliance 1 11 PANTHER Terminal Operations 2 1 PANTHER KOVDGQ and cs ano 2 1 2 2 Advanced Operator FUNCTIONS 02 2 3 Basic Service Information 2224444440000000020000nnnnnnnn nn nn nnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 3 1 Cleaning Maintenance isso rad 3 1 Installation Programming and Service uunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn 3 1 Enor Godos a IN La et 3 2 Chapter 1 Introduction Overview Introduction This manual describes basic operation of the PANTHER Industrial Scale Terminal All installation and servicing should be provided only by authorized personnel NENNEN Overview The PANTHER terminal combines simple operation with the flexibility to be used with a wide range of analog and DigiTOL load cell scale bases while providing fast digitally filtered response to changes in weight It is available in two models The stainless steel harsh environment model is suitable for use on a desktop or other flat surface It can easily be mounted on a wall using the same mounting bracket used for desktop a
17. eder as it stops will add another 2 kg set your preact value for 2 When the material settles on the scale the final weight should be 100 kg The display now shows P1 0 indicating that you do NOT wish to adjust or enter a preact value for setpoint 1 If you do NOT wish to adjust the preact value for setpoint 1 press the Transact Print key Or press the Select key to change the display to P1 1 indicating that you DO want to enter or adjust the preact value for the first setpoint Press the Transact Print key to verify your selection or press the Select key to change the response back to a O or no The display will now show the current value stored as the preact value The most significant digit blinks indicating it may be adjusted Press the Clear key to clear the current value y Te o e Le le o Chapter 2 PANTHER Terminal Operations Advanced Operator Functions To move the active digit to the right use the Memory key A small right arrow appears below the key To move the active digit to the left use the Tare key A small left arrow appears below the key To increase the value of the flashing digit for example to change from 3 to 4 use the Select key Use the above keys to change the digits representing the preact value You may use the Memory move right and Tare move leff keys and the Select increase number key in any combination you wish When the proper preact value is displayed
18. ht of the material inside a container weighing in the NET mode e Place an empty container on the scale platform Te pty p e Press the Tare button e Fill the container or place a filled container of equivalent weight on the scale e The terminal will display the net weight and the NET cursor will light To clear a tare weight 52 e With the scale in the net weight mode a tare weight previously entered press the Clear key e The net cursor will go out and the net weight will be displayed Print Operations To print a weight e f desired tare the weight of an empty container using the steps described above El e Place a load on the weighing platform e Press the Transact Print key 2 2 4 02 Chapter 2 PANTHER Terminal Operations Advanced Operator Functions E Advanced Operator Functions Entry of Setpoint Data During Normal Operation OR 5 8 8 gt The PANTHER terminal is capable of two coincidence setpoints with preact control While setpoint values are always entered as positive values the controls can be set up to turn outputs off when either a positive value feeding into something on the scale or a negative weight value discharging from the scale into a container is entered The setpoint control may be used with optional high level outputs available with the panel mount version These high level outputs may be used in conjunction with external devices provided by other parties
19. lure Other Please specify Comments DO NOT WRITE IN SPACE BELOW FOR METTLER TOLEDO USE ONLY Retail Light Industrial Heavy Industrial Systems RESPONSE Include Root Cause Analysis and Corrective Action Taken FOLD THIS FLAP FIRST NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES BUSINESS REPLY MAIL FIRST CLASS PERMIT NO 414 COLUMBUS OH POSTAGE WILL BE PAID BY ADDRESSEE Mettler Toledo Inc Quality Manager MTWI PO Box 1705 Columbus Ohio 43240 USA AAA A A A A Please seal with tape DECLARATION OF CONFORMITY Konformitatserklarung D claration de conformit Declaraci n de Conformidad Conformiteitsverklaring Dichiarazione di conformit We Wir Nous Wij Noi Mettler Toledo Inc 1150 Dearborn Drive Worthington Ohio 43085 USA declare under our sole responsibility that the product erkl ren in alleiniger Verantwortung da dieses Produkt d clarons sous notre seule responsabilit que le produit declaramos bajo nuestra sola responsabilidad que el producto verklaren onder onze verantwoordelijkheid dat het product dichiariamo sotto nostra unica responsabilit che il prodotto Model Type Panther to which this declaration relates is in conformity with the following standard s or other normative document s auf das sich diese Erkl rung bezieht mitder den folgenden Norm en oder Richtlinie n bereinstimmt Auquel se r f re cette d claration est conforme
20. n to the normal weighing mode To select a target value to be used the scale must be at gross zero Press the Tare key SP1 is displayed momentarily and is followed by the current target 1 value If you wish to use this target press the Transact Print key If you wish to use a different value press the Tare key to display the next target Chapter 3 Basic Service Information Cleaning and Maintenance 3 Basic Service Information Cleaning and Maintenance You may wipe the PANTHER terminal s keypad and cover with a clean soft cloth that has been dampened with a mild glass cleaner Do not use any type of industrial solvent such as toluene or isopropanol IPA as it could damage the terminal s finish Do not spray cleaner directly on the terminal Regular maintenance inspections and calibration by a qualified service technician are recommended ZN WARNING IF THE KEYBOARD DISPLAY LENS OR ENCLOSURE IS DAMAGED ON A PANTHER PANEL MOUNT TERMINAL THAT IS BEING USED IN AN AREA CLASSIFIED AS DIVISION 2 THE DEFECTIVE COMPONENT MUST BE REPAIRED IMMEDIATELY REMOVE AC POWER AND DO NOT RE APPLY POWER UNTIL THE DISPLAY LENS KEYBOARD OR ENCLOSURE HAS BEEN REPLACED BY QUALIFIED SERVICE PERSONNEL FAILURE TO DO SO COULD RESULT IN BODILY HARM AND OR PROPERTY DAMAGE Installation Programming and Service AN WARNING ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THE TERMINAL EXERCISE CARE WHEN MAKING CHECKS TESTS AND ADJU
21. nal is used with more than four Connection is via a terminal strip anglogiload cells e High level discrete output panel mount model only The high level discrete output option provides high level AC interfacing 28 to 280 VAC for the standard low level discrete outputs Up to three output blocks can be installed as part of the panel enclosure AC connections are made via terminal strips on the back panel Other versions of output blocks DC can be installed to control DC voltages rather than AC voltage e PLC network 4 02 1 3 METTLER TOLEDO PANTHER Terminal User s Guide III Specifications Physical Dimensions The PANTHER harsh environment model measures e 6 25 in 159 mm high x 7 00 in 178 mm wide at the front of the terminal e 2 59 in 66 mm deep Wall Mount Orientation 2x 00 29 178 25 4 7 00 1 00 _ d BABBBBH B po 159 6 25 Y ES 74 0 2 91 y 2x 00 50 202 Desk Mount 7 94 Orientation 90 1 4 4 02 Chapter 1 Introduction Specifications The PANTHER panel mount model measures e 3 62 in 92 mm high x 6 75 in 171 mm wide at the front of the terminal e 5 20 in 132 mm deep The optional high level optos add 1 25 in 31 7 mm to the depth
22. nce Model Software Number Revision PANTHER Analog G14891100A L7 1 PANTHER Analog C15379000A L3 1 PANTHER DigiTOL E14988700A L5 1 METTLER TOLEDO RESERVES THE RIGHT TO MAKE REFINEMENTS OR CHANGES WITHOUT NOTICE PRECAUTIONS READ this manual BEFORE operating or servicing this equipment FOLLOW these instructions carefully SAVE this manual for future reference DO NOT allow untrained personnel to operate clean inspect maintain service or tamper with this equipment ALWAYS DISCONNECT this equipment from the power source before cleaning or performing maintenance CALL METTLER TOLEDO for parts information and service ONLY PERMIT QUALIFIED PERSONNEL TO SERVICE THIS EQUIPMENT EXERCISE CARE WHEN MAKING CHECKS TESTS AND ADJUSTMENTS THAT MUST BE MADE WITH POWER ON FAILING TO OBSERVE THESE PRECAUTIONS CAN RESULT IN BODILY HARM AND OR PROPERTY DAMAGE WARNING FOR CONTINUED PROTECTION AGAINST SHOCK HAZARD CONNECT TO PROPERLY GROUNDED OUTLET ONLY DO NOT REMOVE THE GROUND PRONG 2 WARNING DISCONNECT ALL POWER TO THIS UNIT BEFORE REMOVING THE FUSE OR SERVICING N CAUTION BEFORE CONNECTING DISCONNECTING ANY INTERNAL ELECTRONIC COMPONENTS OR INTERCONNECTING WIRING BETWEEN ELECTRONIC EQUIPMENT ALWAYS REMOVE POWER AND WAIT AT LEAST THIRTY 30 SECONDS BEFORE ANY CONNECTIONS OR DISCONNECTIONS ARE MADE FAILURE TO OBSERVE THESE PRECAUTIONS COULD RESULT IN DAMAGE TO OR DESTRUCTION OF THE
23. nt value The most significant digit blinks indicating it may be adjusted You may press the Clear key to clear the current entry 4 02 2 3 METTLER TOLEDO PANTHER Terminal User s Guide 2 4 i 5 5 4 02 Te e e To move the active digit to the right use the Memory key A small right arrow appears below the key To move the active digit to the left use the Tare key A small left arrow appears below the key To increase the value of the flashing digit for example to change from 3 to 4 use the Select key Use the above keys to change the digits representing the setpoint value You may use the Memory move right and Tare move left keys and the Select increase number key in any combination you wish When the proper setpoint value is displayed press the Transact Print key to accept your entry SP2 0 is now displayed indicating you do NOT wish to edit the value for setpoint 2 If you wish to adjust the value of setpoint 2 follow the steps described above Press the Transact Print key to move on to adjusting preact values This capability must have been enabled in setup Preact is the amount of material which may be suspended in the feeder immediately after a signal to close or turn off a feeder is sent The preact amount is entered as a value relative to the setpoint For example if you wish to have a final weight on the scale of 100 kg and the material which will fall from the fe
24. or Functions To move the active digit to the right use the Memory key A small right arrow appears below the key To move the active digit to the left use the Tare key A small left arrow appears below the key To increase the value of the flashing digit for example to change from 3 to 4 use the Select key Use the above keys to change the digits representing the target value You may use the Memory move right and Tare move leff keys and the Select increase number key in any combination you wish When the proper setpoint value is displayed press the Transact Print key to accept your entry SP2 0 is now displayed indicating that you do NOT wish to edit the value for target 2 If you wish to adjust the value of target 2 follow the steps described above Repeat for targets 3 and 4 Press the Transact Print key to move on to adjusting high and low zone values This capability must have been enabled in setup Acceptable tolerance zones may be set for both high and low weights Access to these values by the operator must be enabled in the setup of the PANTHER terminal If this has not been enabled the following steps will not be available to the operator The display now shows F5 8 1 xx indicating the current high zone value This value may be between 0 0 and 4 0 of the target value or within O to 15 increments of target value Selection of percentage or weight units is determined in setup The display will now show
25. ow accept zones may be specified These zones may be determined as a percentage of the target value or as a number of increments of weight as related to the target value The high and low accept zones define the acceptable tolerances around a target value The high and low zones define the point at which the item being checked is outside of an acceptable tolerance around a target weight Setting of target values and tolerance values must be enabled in the setup of the PANTHER terminal This mode of operation must be enabled during setup Refer to the PANTHER Terminal Technical Manual for details With the scale in the normal operating mode press the Memory key The display shows SP1 0 indicating that you do NOT wish to enter or adjust the first target value Press the Transact Print key if you do NOT wish to enter or adjust this target value and to proceed to the next step adjusting the value of the next target OR Press the Select key to change the display to SP1 1 indicating that you DO wish to enter or adjust the first target value Press the Transact Print key to verify your selection or press the Select key to change the response back to a O or no The display will now show the current value stored as target value The most significant digit blinks indicating it may be adjusted Press the Clear key to clear the current value ke 3 1 e e 6 B fe Chapter 2 PANTHER Terminal Operations Advanced Operat
26. ox support Analog powers up to eight 350 Ohm cells scales supported 10 000 d display resolution Pushbutton tare Tare interlock Automatic tare above threshold Automatic clear to gross below threshold Units switching Ib kg g oz Ib oz troy oz dwt tons metric ton Automatic zero maintenance Motion detection and indication Zero indication in either gross or net mode TraxDSP vibration rejection Operator interface Consistent and intuitive operator interaction Program block setup menu Memory functions Storage of zero and tare values during power loss conditions Storage of four target weights for use in over under applications Storage of two setpoint values with preact in setpoint applications Serial data functions Three pre defined output templates Output on demand Print initiation from keyboard remote ASCII command or discrete input Automatic print at setpoint Print interlock to prevent duplicate prints Continuous data output Serial command input Discrete I O functions One programmable input Print Tare Zero Switch Units Three discrete outputs Setpoint 1 amp 2 Coincidence Zero Tolerance Chapter 1 Introduction Optional Features Optional Features Th ii e Analog output both models in Er he ide 2 The analog output option provides one 16 bit analog output port with user available when the PANTHER configurable output ranges of 4 to 20 mA or O to 10 VDC plus a status output termi
27. pplications or can be attached to a METTLER TOLEDO column A panel mount model is also available In addition drawings are available for replacing existing METTLER TOLEDO Model 8510 panel mount terminals Single terminal panel mount kits are available for replacing instruments utilizing a standard 19 inch panel opening 0000 Standard Features Hardware Features Both Models Hardware Features Harsh Model PTHN PANTHER terminals come with the standard hardware features listed on the following pages Seven digit numeric vacuum fluorescent display Six position keypad Screw terminal wiring connectors Single board design Zero and tare weight power loss protection Standard analog load cell input for up fo eight 350Q cells COMI bi directional serial port RS 232 One discrete input three discrete outputs Option expansion connector Sleek fabricated stainless steel enclosure Stainless steel stand for desk or wall mounting Power cord 6 feet 2 meters No exterior screws or latches except for stand mounting Five LEDs for indication of over under condition or setpoint status 4 02 1 1 METTLER TOLEDO PANTHER Terminal User s Guide Hardware Features Panel Mount Model PTPN Software Features Both Models 1 2 4 02 e Extruded aluminum chassis Stainless steel front bezel Certified TYPE 4 4X 12 e Three LEDs for indication of over under or setpoint status Scale functions DigiTOL and DigiTOL J B
28. press the Transact Print key to accept your entry P2 0 is now displayed indicating that you do NOT wish to edit the preact value for setpoint 2 If you wish to adjust the preact value follow the steps described above Press the Transact Print key to move on to adjusting the zero tolerance range This capability must have been enabled in setup L 0115 now displayed indicating that you do NOT wish to adjust the zero tolerance value If you do NOT wish to adjust the zero folerance value press the Transact Print key or press the Select key to change the display to L 1 indicating that you DO wish to adjust the zero tolerance value F5 4 x is displayed where x is either 0 1 or 5 representing that number of increments Press the Transact Print key to verify your selection or press the Select key to change the response to another value The display will now return to the normal weighing mode 4 02 2 5 METTLER TOLEDO PANTHER Terminal User s Guide Entry of Target Over Under Values During Normal Operation 2 6 P 5 4 02 The PANTHER terminal is designed as an Over Under terminal In this mode of operation a series of LEDs are used to indicate if a weight on the scale platform is within acceptable tolerances of a target weight Four different target values may be stored within the PANTHER terminal and recalled by the operator In addition to the specific target values high and l
29. s capable of operation with load cells and bases in a Division 1 or Zone 1 hazardous area when used with approved barriers or when purging is utilized Contact your authorized METTLER TOLEDO representative for information about hazardous area applications for the PANTHER terminal WARNING THE PANTHER TERMINAL IS NOT INTRINSICALLY SAFE DO NOT USE WITHIN AREAS CLASSIFIED AS HAZARDOUS DIVISION 1 OR ZONE 0 1 BECAUSE OF COMBUSTIBLE OR EXPLOSIVE ATMOSPHERES 4 02 1 7 METTLER TOLEDO PANTHER Terminal User s Guide Standards Compliance UL and cUL Listing Weights and Measures Approval Conducted and Radiated Emissions RFI 1 8 4 02 The PANTHER terminal has been tested and complies with UL 1950 The PANTHER terminal is designed to meet CSA standard C22 2 No 143 1975 Office Machines It carries the UL and cUL labels The PANTHER terminal meets or exceeds requirements for Class III IIIL 100006 NTEP division accuracy requirements in accordance with the National Institute of Standards and Technology NIST Handbook 44 A certificate of conformance 96 125A2 has been issued under the National Type Evaluation Program NTEP of the National Conference on Weights and Measures The PANTHER terminal was submitted for approval to the Canadian Weights and Measures Laboratories in Canada After evaluation the PANTHER terminal was found to meet and or exceed requirements for Class IIl
30. t that can be drawn from the 5 Volts DC supply is 15 mA The discrete input for PANTHER is programmable as tare print zero and unit switching Three outputs are used for setpoint coincidence and zero tolerance or zone outputs The PANTHER terminal s COM serial port is an RS 232 transmission port COMI will also support receipt of an ASCII command set which will cause the indicator to Clear Tare Zero Print or change Units COMI can also be configured as an SICS Host Interface port Connections to the Controller PCB are made using screw terminal strips The wire size range for these terminal strips is 16 to 22 AWG The PANTHER terminal can be operated between a temperature range from 14 to 113 F 10 to 45 C at 10 to 95 humidity noncondensing The storage temperature range is from 40 to 140 F 40 to 60 C at 10 to 95 humidity noncondensing Display and Keyboard Environmental Protection Hazardous Areas Chapter 1 Introduction Specifications The PANTHER panel mount terminal s front panel is made of stainless steel and is certified to TYPE 4 4X and 12 specifications The harsh environment terminal s front panel is fabricated stainless steel The display is a seven character seven segment 0 5 in 12 7 mm vacuum fluorescent numeric display The keyboard consists of a flat membrane switch covered with a domed polyester overlay The display lens on both models is polyester Lenses for both models have har
Download Pdf Manuals
Related Search