Important Information Installation User's Guide Tranceiver
Contents
1. Battery BAT 5 The back up battery provides the system the ability to transmit information and activate the siren when power is interrupted If power is ever interrupted wile the system Is activated the back up battery will be engaged The transceiver will receive a ww trigger and the siren will sound in 30 second increments If power is not restored the alarm will continue to transmit and sound for six cycles Note The system has to be correctly installed for at least 12 hours before full function of the back up battery can be used To check the status of the back up battery activate the system using button 1 e If the system chirps 3 times the back up battery is in good working condition e If the system chirps 2 times the back up battery is not fully charged or not installed If power is purposely being interrupted when the alarm is activated turn ignition key on and off before disconnecting power to limit the back up to two cycles instead of six Note If the system chirps only 2 times and it has been correctly connected for more the 12 hours the battery needs replacement Contact Aritronix for replacement options Perimeter Sensor SN 5 Mounting the SN 5 The Perimeter sensor uses high frequency Microwave technology to detect mass density movement around the motorcycle The signal can transmit through the seat fiberglass leather and plastic but not metal It is recommended to place this sensor under the sea2. sensor will be scroll between the Baas se enabled every time alarm is options gt PE sed 9 armed fergn TOS J PEr OFF Perimeter sensor will be disabled every time alarm is Ea Pr of F Transceiver Battery Information Selecting Transceiver Alert Type Audible Silent Vibrate The receiver consists of two functions RFID functions and Two way FM communication Enter programming mode Scroll to the the UAI icon press button 1 to select The LCD will display the current settings To program follow these steps tAn Transceiver will vibrate and Pr Low Battery Stages Press button 1 to a d Aon 2 to sound when a trigger occurs It s recommended that the transceiver be charged daily If the transceiver is not charged daily the scroll between the a save and following stages will occur options exit ALL oFF Transceiver will only flash backlight when a trigger occurs Low Battery When the battery is low the B icon will cycle from 3 bars to 2 bars to 1 bar SR A The transceiver should be charged as soon as possible Transceiver will only sound ul when a trigger occurs Two Way Off If the transceiver is not charged at some point approximately 7 days Two way communication will shut off At this mode the LCD displays rFld onLy The RFID Pn tn Transceiver will only vibrate system will still operate and you will still be able to automatically and manually w
3. snaps 2 Slip male T tap connector over hinged end of the female connector to make a connection Motorcycle Wire Female T tap Motorcycle Wire Male T Tap GEN 1 Wire from GEN 1 Female T tap Alert Type Aud Vibr Range Indicator Button 1 AH Shock Trigger Button 2 Audible Silent Alert Indicator 24 hour Clock Text display SHOCK 19 a TILT IGN N BK UP PER OFF System Status Battery Tilt Trigger Ignition Trigger Perimeter Trigger Back up Power Trigger Charger Input Charging Instructions We recommend that the transceiver be charged for up to 12 hours to insure full life of the battery Plug in provided charger into the transceiver While the transceiver is charging the SNe icon will scroll from empty to full When the transceiver is fully charged the Wp icon will no longer scroll It s recommended to recharge the transceiver every day to maintain full function Remote Battery Status The LCD will display 3 different SNF icons to show the transceiver battery status Motorcycle Battery Status Every time the alarm is activated or deactivated the LCD will display a text message with the current battery voltage If motorcycle battery drops below 11 volts the screen will display CYCLE bAtt LO Transceiver Back light From the main screen pres button lor 2 the screen back light will turn on for 2 seconds Back up
4. Important Information Save this information for future use FCC Notice Installation Date of purchase __ __ ___ This device complies with Part 15 of FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference that may cause undesired operation Place of purchase User s Guide Invoice Receipt Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device Model Number Tranceiver Information Production Code Notes FCC ID MKARI60 Optional Accessories SPECIAL NOTE ON RANGE The average reception range is approximately a mile 800 meters The actual reception range could be greater or less depending on the location and or the presence of obstacles between the vehicle and the receiver The reception range can also be affected by the presence of strong electromagnetic interference from outside sources Appendix Table of Contents Limited Warranty Limited Warranty Products manufactured by Aritronix Ltd are warranted by the company to the original consumer Installation purchaser to be free from defects in workmanship and materials Should a product be found defective Component List Aritronix shall repair or replace the product or any part of the product which Aritronix agrees is defective Planning the Installation 3 P
5. Programming Personal Override code A personal override code will be a sequence of left right left turn signal flashes that can be used if the remote is lost to disable the alarm Enter programming Mode 1 Manually disarm system 2 Turn ignition on off on off on The siren will chiro one time to confirm 3 Press and hold button 1 and 2 for a few seconds until alarm chirps 3 times and flashes light 3 times to confirm Select number of flashes for Code The code will be a combination of left right left right turn signal count Turn on left turn signal to desired number of flashes up to 9 Turn on right turn signal to desired number of flashes up to 9 Turn on left turn signal to desired number of flashes up to 9 Turn on right turn signal to desired number of flashes up to 9 The remote will display the sequence on the screen when done L 22 i The bike will flash the code in the same sequence entered See areal ae eae LCD screen will confirm code Using code in case of lost remote 1 Turn ignition key to on position Let alarm go thru a full cycle until the turn signal lights stop flashing If siren is turned off you do not need to wait for a full cycle 2 Enter code as originally entered 3 When correct code is entered the alarm will deactivate RPS
6. ane Soot 8 without charge during the first 24 months from the date of original purchase provided that the product is Installation Diagram 4 hen PUNGE 8 returned to Aritronix freight prepaid and accompanied by a copy of the purchase receipt UTO DIsarm Installation Warnings and Notes gt g 5 Manual Disarm 8 This warranty does not apply to any product damaged by accident physical or electrical misuse or abuse Mounting the Components 5 M LA 8 installati Herai fe Union e Tood thorized Routing the Antenna Wire 5 anual Arm Ae i SE eration any use contrary to its intended function fire flood unauthorized repair or i Programming and Customizin any other acts of Goa Making Connections 5 i 9 9 Color Code Chart 6 i Aritronix shall not be responsible for removal and or reinstallation charges or theft of the motorcycle or its Entering Programming mode 7 o i Using the T tap Connectors 6 Selecii Peri lors Defaut 3 contents or any incidental or consequential damages caused by any failure of the product to function SIBE Ing ua a S A ek properly Under no circumstances should this warranty or the product covered by warranty be construed User s Guide Selecting Transceiver Alert Type 10 as an insurance policy against loss or damage of any kind Adjusting the Accelerometer 10 Remote Transceiver Icons Selecting Siren Default 1 Aritronix neither assumes nor authorizes any person or organization to make any warranties or assume any and Message Display Set
7. hen a trigger occurs SANS SEKS IS LARA AD ya ene Adjusting the Accelerometer Shock Tilt Sensor proximity to MCM required EET ay ha pss MEE i ea Oe CA eed ee d a ia TREE A No Response If the battery is not recharged and all power is drained The transceiver will not He STI i 4 ua e aa so oe o li x i respond The transceiver has to be charged before it can operate the system ei lie lt e again program follow these steps 1 Least sensitive Press ress Uon Te button 2 fo 5 Most sensitive scroll between the save and options gt exit gt Selecting Siren Default Enter programming mode Scroll to the DR icon and press button 1 to enter the siren menu The LCD will display the current setting To program follow these steps Press button 1 to fera dees button 2 to 1 scroll between the caverdnd Siren will sound and turn options gt exit signals will flash every time alarm is triggered 19 Siren will not sound and turn signals will not flash every time alarm is triggered Setting the Clock Enter the programming mode Scroll to the time and press button 1 to select The screen will display time with the hour flashing To program follow these steps Press Press button 2 to Press button 1 to button 2 toggle between adjusteach gt a pass last digits TS digit me s digit to Zg 8 55 8 54 a NYE Note Clock only displays i
8. n 24 hour format Military time 8 55 RCS Range Confirmation Signal If the transceiver is within range of the MCM and the alarm is activated the LCD will display Yicon If the transceiver does not receive the RCS the icon will not appear Checking Violation Display with Time Stamp If no alarm triggers in memory all sensor icons will be displayed Press button Y tA p El 1 twice quickly Q Bs SHOCK TILT IGN nro ISA BK UP PEROFF DEC U or LU Press button 1 to scroll between triggers Or press and hold button 1 for two seconds to erase memory If the system was triggered the last triggered sensor will be displayed Vf I SHOCK DSi PER OFF ori Trigger Total of triggers al yw ae O SHOCK la n D C tL 7 Time of trigger co ri Transceiver Information Alarm Triggers When the system is triggered the siren will sound and the turn signal lights will flash The transceiver s LCD will display the following messages le If bike is bumped the LCD will display MK icon The siren on the bike will sound for 5 seconds and the lights will flash This cycle will repeat twice If the perimeter sensor triggers a full alarm cycle the LCD will display PER icon The siren on the bike will sound for 5 seconds This cycle will repeat twice Note The turn signal lights will not flash for a perimeter se
9. nsor trigger AR If the bike is tilted the LCD will display TILT icon The siren on the bike will sound for 30 seconds and the lights will flash This cycle will repeat six times If the ignition switch is turned on or tampered with the LCD will display IN Icon The siren on the bike will sound for 30 seconds and the lights will flash This cycle will repeat six times If the main harness or battery power suppjy is disconnected assuming optional Back Up battery is installed the LCD will display mp icon The MCM 9 will still continue to sound and transmit from its internal power source The siren on the bike will sound for 30 seconds This cycle will repeat six times The transceiver will continue to flash the triggered icon until any button is pressed Encoding a Transceiver Note The transceivers are programmed from the factory Encoding is only necessary should the transceiver lose its code and will not arm or disarm the security system or if a second or replacement remote is obtained Unplug HAR 1 from the MCM 9 and plug it back in the siren will chirp 2 times and the lights will flash 2 times Within 6 seconds of plugging in the HAR 1 turn ignition switch ON and OFF 3 times If step 2 is done correctly and within the time allowed the siren will chirp 2 times and the lights will flash an additional 2 times to confirm that the system is in Learn Mode Press and hold button 1 until the system chir
10. on 2 Siren Chirp 1 Time Turn Signals Flash 1 Time Manual Disarm Siren Chirp 1 Time Turn Signals Flash 1 Time Note Ifthe system is manually disarmed it will stay in disarmed mode At this mode the system will not auto arm upon turning ignition key off Press and hold button 1 Manual Arm system has to be manually disarmed first Via D Siren Chirp 3 Times Turn Signals Flash 1 Time Programming and Customizing Instructions Entering Programming Mode 1 van i Programmable 2 Press button 2 an a i Ta mere options will be again to scroll i quickly i displayed through GI ga nk The selected programmable ene A icon will flash ti O T mode options i prional ACCeSSsOreS I9 PER OFF 19 PER OFF i i i neo l woo hi ie nei Perimeter Sensor SN 5 Back up Battery BAT 5 Ignition Disable RID 5 Press button 1 3 to select icon and to begin programming Note Remote will time out of programming mode after 20 seconds No changes will be saved Note To exit programming mode scroll through all icons once Selecting Perimeter Sensor Default Enter programming mode The FF icon will begin to flash press button 1 to enter the perimeter sensor menu The LCD will display the current setting To program follow these steps Press button 1 to gra 24 PEr on Perimeter
11. otorcycle for placement of components LI Verify that no moving parts interfere with the components or their wires LI Verify that chosen location is not near extreme heat Component Check List TRS 9 MCM 9 RFID antenna AC Adapter GEN 1 Bag T taps x4 ACC 1 Bag Velcro Pieces x2 Zip Ties x4 Dust Cap x1 DO HAR 1 Bag Appendix O OOOOO Grey Wire Turn Signal To Battery les T FRE SENERE ee faert ome fr et ony a Grey Wire Turn Signal Optional Orange Wire Tail light Black Wire Ground Perimeter pasta Sensor Generic Connector Kit GEN 1 Accessory Harness ACC 1 Main Harness HAR 1 Ignition Disable Seng Main Control Module MCM 55 Installation Warnings and Notes g Connect the HAR 1 harness to the MCM only after installation is completed Note When the main harness HAR 1 is plugged in the siren should chirp Ifthe siren does not chirp check the alarm inline fuse connection to battery and connection to ground Ifthe battery is to be removed disconnect HAR 1 connector first Reconnect only after battery terminals are reconnected Mounting the Components Select a suitable location underneath the seat or in a side cover Mount components using velcro or cable ties Make sure that the components are not exposed or accessible o Place MCM as flat as possible to achieve best performance o Place RFID antenna
12. ps 2 times and the lights flash 2 times to indicate that the MCM has learned the code The transceiver echoes 4 chirps and the LCD displays LERN DONE to confirm that the transceiver is encoded If you are encoding a second transceiver repeat step number 4 for the second transceiver before continuing to step number six Turn ignition ON and OFF to exit Learn Mode Button 1 x 0 Main Harness HAR 1 Additional Information Sensor Memory Display When the system is disarmed the turn signals will flash to indicate if there has been an alarm trigger The lights will flash once to indicate that the system has been disarmed additional flashes indicate that the following trigger has occurred 1 flash then 1 additional flash Shock Trigger 1 flash then 2 additional flashes Tilt Trigger 1 flash then 3 additional flashes Perimeter Sensor Trigger 1 flash then 5 additional flashes Ignition Trigger Motorcycle Battery Safeguard with sleep mode e If the optional perimeter sensor is being Used and the alarm is armed for more then 10 days the system will automatically disable the perimeter sensor If the alarm is armed for more than 30 days the system will automatically shutdown its RF capabilities In this mode the transceiver will no longer be able to operate the system but the system is still armed and protecting the bike e To disarm trigger the alarm and press button 2 Manual Override Procedure
13. r to options on page 22 2 Attempt to start bike to test if correct wire is selected If bike starts the wrong wire is selected contact Aritronix for assistance If bike does not start correct wire was selected continue to step 3 3 When packaged the RID 5 wire ends have been treated with clear silicon to protect the ends from fraying Make sure they are stripped bare of this before continuing 4 Connect one end of the cut wire to one of the blue tabbed wires in RID 5 with provided butt connector or any other solid connection option 5 Connect second end of the cut wire to second blue tabbed wire in RID 5 with provided butt connector or any other solid connection option 6 Test connections to insure that they are as solid as possible Plug the RID 5 connector into the matching connector on the Accessory Harness 8 Test RID 5 by activating alarm without perimeter sensor and try to start bike If bike starts please contact Aritronix for assistance Pa Failure to test for a loose wire could cause an accidental engine cut off E i li de E Color Codes Color codes are not always valid Always verify before making connections Ke ESS Ground Tail Light Left Turn Signal Right Turn Signal Honda Green Brown Orange Blue Black White Green or Black Harley Davidson Yellow White Black White Green Using the T tap Connectors and GEN 1 Connector 1 Place the female T tap connector over wire close and squeeze until it
14. sh connected or connected to wrong wires Test wires and change connections to correct wires Perimeter Sensor not i Check connections working Sensor not connected System set on default with sensor Enter Programming mode and off change default Connect orange wire from GEN 1 to 12 volt with ignition key on In most bikes that is the tail light wire Ignition Disable does Orange wire from GEN 1 not not work connected Refer to options on the ignition disable instruction page Test selected wire before reconnecting RID 5 wires Ignition disable not connected to correct wire on bike al Manual Override Procedure Programming Personal Override Code Enter Programming Mode Select number of flashes for Code Using Code in case of lost remote Transceiver Information Alarm Triggers Range Confirmation Signal Checking Violation Display Transceiver Battery Information Low Battery Stages Optional Accessory Instructions Perimeter Sensor SN 5 Back up Battery Ignition Disable Anti hijack Unit Appendix Trouble Shooting guide Limited Warranty Important Information Notes FCC Information Special Note 14 14 14 14 15 16 16 1 1 12 21 22 al a2 a3 a3 a3 Installation Components MIL GEN 1 4 ce POS MCM 9 RFID HAR 1 antenna TRS 9 Transceiver Planning the Installation LI Check that your motorcycle battery is fully charged LI Check the layout of the m
15. t as close as possible to the center of the motorcycle With the provided Velcro you can mount this sensor on top of the battery or any flat surface making sure that the top side of the sensor is facing upwards Place the perimeter sensor as faraway from the MCM as possible Adjusting the Sensor Although the sensor is pre set from the factory it may be necessary to adjust the sensitivity to suit your needs Remove the plastic cap and turn the adjustment screw To increase sensitivity turn adjustment screw clockwise To decrease sensitivity turn the adjustment screw counter clockwise Plastic Cap Remove to adjust sensitivity Note Do not turn sensitivity above half way Doing To Accessory Harness on Main so may cause false alarms Control Module MCM Operating Instructions The SR i900 by default will be in auto arm mode and will activate with the perimeter sensor off and the siren on five seconds after turning the ignition key off Turn ignition key off Walk away from bike Press and hold button 1 and 2 Press and hold button 1 ISO y A al Auto Arm via ag Siren Chirp 3 Times Turn Signals Flash 1 Time Activate perimeter sensor Siren Chirp 4 Times Turn Signals Flash 1 Time Panic Stop Trigger when system is armed Siren Chirp 6 Times Turn Signals Flash 1 Time Auto Disarm Walk next to bike Turn ignition key on Press and hold butt
16. ting the Clock 11 liability in connection with the sale installation or use of this product Transceiver Charging Instructions 7 Encoding the Transceiver 12 Transceiver Battery Status 7 This completes Aritronix warranty and no other warranty exists Motorcycle Battery Status 7 i Transc AV er Back light 7 Acguoneinicimalon What should you do if you experience a problem with a Scorpio product O Hi meen 8 Sensor Memory display 13 First contact Aritronix Ltd Proof of purchase installer and motorcycle information will be requested lf Pe Ne MEG S Motorcycle battery safeguard 13 after assistance from our trained staff it is determined that the Aritronix product may be faulty then you will Auto A 8 MORO 7 7 U Si rm be provided with detailed information on processing a warranty claim and instructions on how to send the Activate Perimeter Sensor 8 product into our repair office All warranty claims must contain a return material authorization RMA Aritronix will not accept any package that has not been approved for warranty repair exchange and an issued RMA Shipping charges may apply Problem Possible Cause Solution Will not arm i RFID antenna not connected I from MCM to RFID Verify connection to power lead and ground connection Verify connection to 12 volt wire with key on tail light on most bikes Power or ground not connected Orange wire not connected Grey wires from GEN 1 not Turn signals will not fla
17. under seat or tail section do not chose a location that is covered with metal Routing the Antenna Wire For best performance the last 6 of the antenna should o Be as vertical as possible Antenna 6 o Be away from metal as much as possible a Extension 12 Making Connections ca The necessary connector or wires are found under the seat or in the tail section of the bike Removal of the tail section plastics or side cover might be necessary Ignition Engine Control Wire Options Option 1 Positive lead wire on fuel pump Option 2 Positive lead wire on fuel injection system Option 3 Positive wire that goes to the ignition fuse in fuse box This should be either a 10 or 15 amp fuse labeled IGN Carbureted Bikes Only Option 4 Ground wire from ignition module Option 5 Positive wire from ignition module to ignition coil Operating the Anti Hijack Feature While the engine is running press and hold the transceiver s button 1 and button 2 at the same time for 3 seconds The siren will begin to chiro confirming that the Anti Hijack feature has been activated 15 seconds later the siren will go off continuously and the engine will shut down To disarm turn off the ignition switch and press button 2 ee To Accessory Harness on Main Control Module MCM h To CUT wire on motorcycle Ignition Disable Anti hijack Module RID 5 Installation Cut the Ignition Engine control wire refe
Download Pdf Manuals
Related Search