USER MANUAL - Smart
Contents
1. Turbine maximum input power 350W 600W 1000W PV Input current range initial value 0 30A 15A O 30A 10A O 22A 8A PV Maximum input power 500W 1000W 1500W PV MPP 17 20V 34 40V 68 80V Number of output circuits 2 channel or 1 channel with dimming signal Output control mode Always open light controlled light on time off Maximum output current utility power interface Optional Operating temperature range 20 50 C Operating humidity range 35 85 no condensation Be 15 Page 15 Vil Common Faults and Troubleshooting If the above statements are not satisfied or there is any abnormal phenomenon and the controller cannot return to normal please contact the after sale service or business personnel of our company for maintenance or replacement in a timely manner Storage battery box i flickers It is over discharged The storage battery is emptied Please fully charge the storage battery before use and there is no output The system detected output overlead and will disable the overloaded output Load icon Y flickers and loop the other loop will not be affected Please check the loads and remove there is no output the unnecessary or abnormal loads Press Esc to recover The system detected output short circuit and will disable the short circuited is on and there is no output output loop the other loop will not be affected Please check the loads and connection lines After troubleshooting pre2. 5 5 DC load output mode setting interface i m x5 Charge DC OUT ji ta He au LOAD In this Manual Channel 1 load is used as an example and its setting process is stated 4 5 5 1 Normally open mode interface Lo aR ERAH xf l x5 Charge DC OUT 1 He A a LOAD In this interface as shown in Fig 4 5 5 1 press A and the Channel 1 or 2 load setting interface can be switched over For each channel press O set confirm key first and the screen will display a SET sign and then press A or 7 Channel 1 load can be switched over among the three output modes normally open light controlled on off light controlled on time controlled off Users only need to select the mode they need and then press O to confirm and press key to save and quit 4 5 5 2 Output mode interface of light controlled on off BIN Page 11 AR Bm xe ett xt Charge DC OUT 1 5 WSETS Ge AY xt LOAD 4 5 5 3 Output mode interface of light controlled on time controlled off I TH Baga oo 208 EE x5 Charge DC OUT 1 FF KS ETE 4 1 AF gt Di aN LOAD The output mode setting of Channel 2 is the same and its interface is as follows Ky 4 5 5 4 Output mode setting interface of Channel 2 load z4 Charge DC OUT 2 J SETH Fi AX on 6 LOAD 4 5 6 Manual brake operation To ensure the operation safety of wind generator and for the convenience of users this controller i
3. Esc key after confirmation for normality to manually recover it to original status Figure An icon of manual brake when it is on it indicates under manual brake status otherwise status of manual brake unlocked See Figure An icon of the item browsed 4 2 currently See Figure Unit icons A current unit A 4 2 V voltage unit V W power unit W H hour BEN Page 6 Mm A symbol of light amp time control Disa symbol of light amp time control When appears it indicates light controlled on off and when appears it indicates light controlled on time controlled off Output on off status Two channel load output Channels 1 and 2 interface 4 3 Day and night identification It is night if the photocell voltage exceeds the light controlled on voltage can be set by users for continuous 1min It is day if the photocell voltage exceeds the light controlled off voltage can be set by users for continuous 1min 4 4 Output mode Normally open output mode The voltage of battery is normal and within the rated load The controller outputs will full power normally Light controlled on time controlled off output After dark see 4 3 Day and night identification it outputs according to mode the set load upper limit and the output off time is subject to the set time Light controlled on off output mode After dark see 4 3 Day and night identification it outputs accordin
4. of the battery vr E hand brake s i aki A wind generator r en ui are lt gt g te i B day and night CHARGE x wT ee je r 2 L output interfaces 1 TR SET og g g Bi wea LEJ Ai 7 Ton OFF O AR F F Cumentiy browsing items K the conditions on off output I set state units J output modev H Digital display area Er Indicating wind generator A symbol of sun indicating daytime y A symbol of moon indicating nighttime When the battery is fully charged 5 bars inside will all display Z when the storage battery is over discharged the symbol win flicker and then stop flickering upon recovery from over discharging status when battery storage is under over voltage status a battery status indicator bar will appear and A symbol of storage battery the over voltage symbol will flicker and then with the bars inside indicating stop flickering upon recovery from over voltage status the battery charge status Under a normal load indicator lamp will appear when without output while indicator lamp will appear when with output under over load status load symbol YE flicker at this time you need to eliminate the excessive load and then press Esc key to pode nats end DIE STatl recover the output under short circuit protection ly N Short circuit symbol will be on at this time you should check the load line and then press
5. 3 V Protection Mechanism Protection Protection description contents General If the rotate speed of wind generator exceeds the preset rotate The controller speed of braking it will automatically brakes through three phase has automatic short circuit and the brake is off automatically after 3min braking function over speed brake or brake off 2 Over speed brake If there are more than successive 3 overspeed brakes within 30min or brake off under it will be determined as continuous strong wind and the brake can continuous strong be off automatically only after 4h wind Exceeding safe When it exceeds the safe temperature because of overhigh ambient The controller temperature temperature or overhigh temperature caused by heavy current the has a built in system will enable over temperate protection automatically disable temperature wind generator and photocell input but the output will not be testing module affected Temperature Over temperature protection is freed and the system recovers to decreases to safe normal state temperature This controller has good heat dissipation measures and the over temperature protection module will not be enabled under non extreme cases 14 i Page 14 VI Performance Parameters Turbine input voltage range Seinen EEE Eee Turbine input voltage range range O 100V Turbine input current range Turbine input current range initial val va O 25A 15A 0 20A 15A
6. RL AL xt occ WND 0 00W in the picture shows the current power of wind generator Press A solar PV parameter state and the current voltage current and power of solar PV can be viewed 4 5 3 Operating parameter state of solar PV module 4 5 3 1 View the voltage of solar PV 4 5B ERAH ie Charge DC OUT xt 0 00 ki 0 00V in the picture shows the current voltage of solar PV Press A to enter into the next parameter state and the current of solar PV can be viewed 4 5 3 2 View the current of solar PV BIN Page 9 FH Eis E03 See Charge DC OUT xt 0 00 Er 0 00A in the picture shows the current voltage of solar PV Press A to enter into the next parameter state and the current power of solar PV can be viewed 4 5 3 3 View the power of solar PV TH Bit IE q lt a Charge DC OUT xt 000 PY 0 00W in the picture shows the current voltage of solar PV Press A to enter into D load parameter status and the current of DC load can be viewed 4 5 4 Operating parameter state of load 4 5 4 1 View the current of DC load 4 zE ERAH 3 a Charge DC OUT Di AK xt 0 00 LOAD So far the operating parameters of various parts of the system have been all viewed if you need to look back certain parameter press P to display parameters counter cyclically In this interface as shown in Fig 4 5 4 1 press A to enter into output mode setting of Channel 1 and 2 DC load KION Page 10 4
7. USER MANUAL LCWS B Intelligent Duck amp Boost Wind Solar Hybrid 20120314 VERSION 1 Safety Caution 1 Thank you for purchasing our controller Before you install and use the product please carefully read the User s Manual and properly keep it 2 The controller shall be installed by an experienced technician in strict accordance with the User s Manual to guarantee that it can work normally 3 Keep the product free of contact with corrosive gas and humid environment for a long time 4 Be sure not to place the product at a place where it is exposed to humidity rain sun severe dust vibration corrosion or strong electromagnetic interference 5 Please don t open the product s casing to repair it by yourself Table of Contents Product OVEN VIC W a 1 ll DESCriPtiONn OF Model aan 2 Il Installation SPeCitiCatl OM ccc x2 u2a8 28 RR RR RR ER ara aan 3 IV LCD Operation and Display Instructions ccscscsecscsccsceccccsceccccsceccccsceccccscescecscescecscees 5 4 1 DeSscrption Of KeyS uuuuanana ara 5 4 2 Description Of display Content 5 4 3 Day and nieht identification u a 7 A A QUEBUEMOdE ea 7 4 5 INStFUCTIONS for control panel u a 8 V Protection Mech nism uc an gt 14 VI Performance Parameter ana 14 VII Common Faults and Troubleshooting csscecsccscecsccsceccccsceccccsceccccsceccccscescccnceccecscess 16 VIII Warranty and After sale Service aaa BRITEN 16 I Pro
8. duct Overview This controller is specially designed for high end small wind solar hybrid systems and applies to wind solar hybrid street lighting systems and wind solar hybrid monitoring systems Its main functions are shown as below 1 This controller being a high performance wind solar hybrid controller can control wind generators and solar cells to charge or discharge the storage batteries at the same time when charging it adopts high resolution PWM mode to charge the storage batteries via voltage and current limiting which can effectively prolong the storage batteries service life 2 The controller is provided with an accurate rotating soeed measuring and controlling module so it can check the wind generator rotating speed in real time and also can realize over speed brake according to the set upper limit of safe rotating speed 3 The controller is provided with two channel DC output interfaces and each channel has a maximum output current 10A for each channel the user can independently set three kinds of different output modes namely light controlled on off light controlled on time controlled off and normally open 4 The controller is provided with MPPT maximum power point tracking function It via advanced algorithm can automatically search the maximum power point to realize the maximum conversion from wind energy to electrical energy Through test compared with traditional controllers this controller can impro
9. e 3 Controller 2 Controller 1 Rs485 explanation N i Computer Rs485 interface anode cathode GND Description Each controller is provided with a RS485 communication port When two controllers are connected they shall be connected in a way of anode to anode cathode to cathode and GND to GND and finally connected to the RS485 port behind the computer via the third RS485 port and the like Connection diagram of LCWS B wind solar hybrid controller with communication port RS 485 optional Dimmer port and communication port RS485 are optional so the customer shall clearly specify what you need otherwise we will deliver the one in standard configuration After the parts of wind solar hybrid generator system and photovoltaic panel are installed and external circuit construction is completed it is required to connect and operate the system parts safely and reliably according to the following sequence 1 Open the package to confirm that the equipment is not damaged in transportation 2 Connect the DC load to DC OUTPUT terminal The loads of two channels share the same anode Connect the first channel load to 4 and 1 of DC OUTPUT and the second channel load to and 2 of DC OUTPUT 3 Connect the storage battery to the BATTERY terminal of back panel of equipment with the cable with copper conductor of 6mm2 and above A reverse connection between anode and cathode of t
10. ection storage battery over charging over discharging protection storage battery open circuit protection storage battery reverse connection prevention protection overload short circuit protection lightning protection wind generator current limiting protection wind generator over speed protection automatic and manual brake protection of wind generator controller temperature monitoring over heat protection load over voltage protection Note Except for storage battery reverse connection prevention protection other protections above won t damage the components 8 The controller casing made of high quality aluminum alloy is well designed and has an attractive appearance and a good heat dissipation performance 9 The controller is manufactured with strict production process and high quality industrial components so it can run reliably for a long time under cold high temperature or humid environment Ban Page 2 II Description of Model LCW S B1 B2 Internal code Solar energy Wind energy X Note Refer to VI Performance Parameters for detailed information II Installation Specification e Jel ejam j ulm JB Output terminal connection diagram of LCWS Bx wind solar hybrid controller with double channel standard configuration l lel 1 lr a pine Output terminal connection diagram of LCWS Bx wind solar hybrid controller with single channel dimming signal optional BIN Pag
11. g to the set load upper limit and the output is off after the dawn 3B 7 Page 7 4 5 Instructions for control panel 4 5 1 Start up interface FRE Ein e f Ch ih DC OUT 27 HE Yt xt 6 60 a In the start up interface 0 00V shows the current voltage of storage battery Press A key to enter into wind generator parameter state and the current rotate speed voltage current and power of wind can be viewed 4 5 2 Wind generator operating parameter state 4 5 2 1 View the current rotate speed of wind generator bana z gig re Charge DC OUT IE apgr en 0 00M in the picture shows the current actual rotate speed of wind generator Press A to enter into next parameter state and the current voltage of wind generator can be viewed 4 5 2 2 View the current voltage of wind generator 4 zE ay xe Charge DC OUT JALAL SE ooy Ab 0 00V in the picture shows the current voltage of wind generator Press A to enter into next parameter state and the current of wind generator can be viewed 4 5 2 3 View the current of wind generator BEN Page 8 y FH Bein IE 3 ss Charge DC OUT XL AJL xt 0 00 WIND 0 00A in the picture shows the current of wind generator Press t enter into next parameter state and the current power of wind generator can be viewed 4 5 2 4 View the power of wind generator 4 AE ERA Sie a ae Charge DC OUT J
12. he storage batteries is forbidden in order to avoid damaging components 4 When wind generator is under static or low speed running status no wind connect the wind generator output line to the WIND INPUT terminal of back panel of equipment 5 Shield and then connect the solar cell panel to the SOLAR INPUT terminal of back panel of equipment according to anode and cathode 5B 4 Page 4 6 Set corresponding parameters to select the load output mode via the keys on the controller s LCD IV LCD Operation and Display Instructions Diagram of panel keys Function description Add or display the next value if under browsing status press it to switch to next parameter display if under setting status press it to add the current parameter value modified Reduce or display the previous value if under browsing status press it to switch to previous parameter display if under setting status press it to reduce the current parameter value modified Setting confirmation if under browsing status press it to enter the setting status if under setting status press it to store the parameters and return to the browsing status Cancellation manual switch if under setting status press it to return to the browsing status but not to store the values modified if under browsing status use it as a manual setting key in case of load short circuit or over load 4 2 Description of display content 5 sor cr C status
13. s so designed that the wind generator can be braked manually under any state The specific process keep O confirm key on the panel pressed first and gt lt then press ESC key and hold for about 5min Loosen the key to enter manual braking state and there will be Brake displayed at the top right corner of the display interface If you want to quit manual braking state repeat the above operation namely keep O confirm key on the panel pressed first and then press ESC key and hold for about 5min Loosen the key to quit manual braking state Brake at the top right corner of the display interface will disappear The specific interface is shown as follows 1 Manual braking interface Brake appears at the top right corner of the display interface 12 i Page 12 lt means the wind generator brake when brake appeard here uo Re sen Kr x5 Charge DC OUT FF SET fi HR i an amp LOAD Brake appears and the wind generator brakes 2 Quit manual braking Brake at the top right corner of the display interface It means the wind generator quits braking when brake disappears here N x5 Charge DC OUT If WSETH ta 2 IS LOAD After wind generator brakes it will stop rotating or rotate at a very slow speed The wind generator is unable to generate electricity Brake disappears and the wind generator quits braking state 13 Page 1
14. ss Esc to recover The temperature of the controller is too high and the over temperature The output is normal but it is not protection the wind generator brakes the photocell has open circuit but the charged output will not be affected When the temperature decreases to recovery temperature the system will recover Vill Warranty and After sale Service 1 The product quality warranty of our company is one year or in case of any defect or fault found within the quality warranty year as agreed in the contract our company will provide free maintenance service Place contact the after sale department or related business personnel of our company 2 The warranty range in this quality warranty clause is exclusive of damages caused by external factors such as damages caused by force majeure e g accident and natural calamities use not in accordance with the product specification improper use negligence refit repair improper installation improper testing improper transportation etc oF 16 H Page 16
15. ve the charging efficiency by more than two times at maximum 5 The controller is provided with a customized LCD so the user can easily check and set the status of controller via the human computer interaction interface The items which can be checked storage battery voltage wind generator rotating speed wind generator voltage wind generator current wind generator power photocell voltage photocell current photocell power the first channel output mode the first channel output turn off time the second channel output mode the second channel output turn off time light controlled on voltage point light controlled off voltage point daytime or nighttime indicator storage battery status load status as well as the status of faults like over voltage under voltage over load and short circuit The items which can be set the first channel output mode the first channel output turn off time the second channel output mode the second channel output turn off time light controlled on voltage point and light controlled off voltage point 6 The controller is provided with a unique solar charging circuit with a small loss and heat which is of open circuit unloading mode so as to effectively prolong the solar cell s service life BIN Page 1 7 Complete safety protection functions including solar cell reverse charging prevention protection solar cell reverse connection prevention protection solar cell current limiting prot
Download Pdf Manuals
Related Search