User Guide
Contents
1. suitable in mode before you lock the control panel situations where you wish to have control of the sauna for 1 Push the up arrow a example when children are 2 Push the down arrow VW playing in the vicinity and you 3 Push the fan button want to hinder that the heater The display show LOCKED is turned on by mistake Remove the lock with the same combination a S Lock the fan or lighting When the fan or lighting is fo Lock the fan or light N locked it is impossible ee Make sure that the control panel is in Off off the ventilation or turn off mode before you lock the fan or lighting the light in the sauna The light cannot be turned off and the 1 Push the fan button or ventilation cannot be cut off the lighting button before the lock has been 2 Push the up arrow yN removed 3 Push the down arrow v 4 Push the fan button The display show LOCKED Remove the lock with the same combination g A ra Observe Do not pause more than one second when pushing the buttons as you are activating or deactivating the locks 12 Control panel Digi II Alarm When there is an alarm situation the control panel stops the heating and the cause for the alarm is shown on the display of the control panel C A Alarm Display What to do The cable of the temperature sensor is broken ALARM Check the cable to and T1 CABLE OFF from the sensor Check the cause Reset The temperature se2. User Guide Digital control panel Digi Il Model 1601 12 User Guide for the following models of contactor boxes WE3 2005 3 WE4 2005 4 WE5 2005 5 Control panel Digi II Thank you for choosing quality products from Saunatec We think that our products will live up to your expectations and give you many hours of enjoyment in your sauna We want you your family and your friends to have many comfortable sauna baths and at the same time find new ways to enjoy sauna bathing We have taken today s demands on sauna bathing into consideration and equipped the sauna heater with many usable and unique functions Among other things the control panel has four memory buttons which can be pre programmed to your personal favorite sauna bath Read this manual carefully The manual is divided into two separate sections The first is for you as a user and the second is for the installer Saunatec is the world leading producer of products for saunas and steam saunas We develop produce and market products for saunas and steam saunas in the whole world Saunatec has the largest factories of sauna products in the world Finland Germany and USA and a well developed net of retailers both nationally and internationally Our product range consists of sauna and steam rooms electric and wood heaters control panels and sauna accessories Pentti Piisku President Saunatec Group OY User Guide Digital control panel Digi II Copyrigh
3. e button to start the heater To start the sauna heater you need to adjust the following parameters 1 Start time when the heater is to start 2 Temperature the temperature in the sauna a Q Memory buttons We recommend that you take advantage of the memory buttons when using your sauna You can easily enter your preferences on separate buttons When it is time to take a sauna bath you activate them with a single push Each memory button has preset values when the control panel is delivered from the factory Read more about memory buttons on page 9 3 Duration the length of time the heater is to be on Basic settings Before you use the sauna you need to set the basic settings on the control panel These basic settings are setting the time and choosing the language Read more about basic settings on page 6 You easily set the You set the time by programming in the menu temperature with the mode See more information on page 6 digital control panel Control panel Digi II Set the time and chose the The control panel returns automatically to the off mode from the menu mode if you do not push a button within three seconds If a change is done it must be approved with the prog ok button before the control panel resumes off mode otherwise the change is not saved 7 Set the time Make sure that the control panel is in off mode before you set the time 1 Push the button prog o
4. e electricity Mount and program the control panel 0 0 15 XY DA Control panel Digi II The control panel and included parts Memory button 1 Memory button 2 Memory button 3 Memory button 4 The button prog ok Z Page downwards in the menu Page upwards in the menu ED Activate function OK Display On Off Temperature Start time ED S Duration Lighting Ventilation The display Start time 13 28 4 88 C f Temperature Duration 0451 ra Observe If lighting and ventilation have been connected to the control panel you can activate them with the appropriate buttons If they are not connected contact your retailer or a certified electrician You access the settings of the control panel clock and language by pushing the button prog ok for three seconds when the panel is not on o Tips and advice The control panel gives you the opportunity to set four separate sauna baths We recommend that you utilize the useful function of the memory buttons Read more on page 9 Control panel Digi II Functions of the control panel With the control panel you set the time for the heater to start for how long it will work and the temperature in the sauna It is also possible to program four memory buttons for special sauna baths This means that you only need to push on
5. emory buttons The digital control panel has four memory buttons As a user you have the opportunity to set four separate sauna bath programs Each program has its owns adjustments and you activate them with just a push of a button Memory buttons When the control panel is delivered from the factory the memory buttons are pre set It is a good idea however to change the settings so that you get the sauna bath of your choice Set the temperature and duration of the sauna heater according to earlier instructions see page 10 The preset values of the memory buttons are E Duration Two hours lm Temperature Button 1 60 C Button 2 70 C Button 3 80 C Button 4 90 C 7 Program a memory button 1 Enter a duration on the control panel 2 Enter a temperature on the control panel 3 Push one of the memory buttons 4 Push the button prog ok Ag A Activate a memory button 1 Start the control panel with the On Off button 2 Push one of the memory buttons J Check a memory button 1 Make sure that the control panel is in Off mode The display is not lighted 2 Push a memory button and read the settings The display is lighted W P Control panel Digi II Change the settings during the sauna bath The instructions below show how to change the settings during the sauna bath You may want to lower t
6. he temperature or shorten the duration Change the temperature 1 Push the button for temperature 2 Set the new temperature with the arrow buttons WwW 3 Approve the new temperature with the button prog ok Ne A Change the duration 1 Push the button for duration 2 Set the new duration with the arrow buttons WwW 3 Approve the new duration with the button prog ok Ne A Turn off the sauna 1 Push the On Off button The display shows 14 00 Observe _ To change the settings during the sauna bath does not change the values in the memory buttons The change only affects the ongoing sauna bath Control panel Digi II Calibrate the temperature If you have a thermometer inside the sauna that does not show the same temperature as that which has been entered on the control panel you can make a calibration Offset This means that you adjust the control panel and the thermometer after the same scale That the temperatures differ is due to the fact that the warmth in the sauna is not exactly the same in all spaces Example Your thermometer inside the sauna shows 84 C and your control panel is set on 80 C The difference is thus 4 C By setting OFFSET T1 on 4 C the control panel will show the right temperature Make sure that the control panel is in Off mode before you calibrate the temperature 1 Push the b
7. k for three seconds The display shows MENU 1 CLOCK 12 08 2 Set the time with the a arrow buttons Vv 3 Approve the new time with the button prog ok NX J Chose language Make sure that the control panel is in off mode before you chose language 1 Push the button prog ok for three seconds 2 Page to Menu 2 by pushing the button prog ok The display shows MENU 2 LANGUAGE ENGLISH 3 Chose the new language with the arrow buttons 4 Approve the new language with the button prog ok Ne J ra Observe If there is a power failure of more than 20 minutes the time is deleted from the control panel Then you have to reprogram the setting The control panel has five languages to chose from Finnish English Swedish German and Dutch Control panel Digi II Set start time temperature and duration 1 d Tips and advice Set the start time i By holding the arrow button depressed the values are The start time is the time that the paged up or down fast heater turns on for example 18 30 1 Start the panel with the On Off button The background lighting is lighted 2 Push the button prog ok The display shows earlier chosen settings for example 1400 A 70 C 01 30 3 Push the button for start time The display shows START TIME 14 00 4 Set start time for example 18 30 with the arrow v bu
8. nsor ALARM the sensor by pushing is triggered CLEAR T1 the reset button with a screwdriver 13 Control panel Digi II Connect the electricity Wiring diagram for Control panel cable control panel A1 White Bt Pink A2 Brown B2 Blue A3 Green B3 Red A4 Yellow B4 Black A5 Grey B5 Violet Control panel cable a Heater or contactor box OOO CCS E TERETE Mount and program the control panel The control panel has several holes in the back These holes are used to mount the control panel outside the sauna In order to reach the holes the control panel must be opened using the two keys that are included The control panel can be mounted in or on the wall When the control panel is installed and the lid is replaced you have to set a number of basic settings on the display The basic settings include among other things to set the time and chose the language 138 34 109 a E Tes 149 28 118 NUNN D Hdoood m J i M Dimensions of the control panel Digi II 14 Pa Mount the control panel s 1 Use the control panel opener to open the lid Set the sheet metal screws Lead the cable through the control Put the lid back on and set the Mark on the wall where the control panel sho
9. t 2004 Saunatec Group OY All rights reserved Control panel Digi II Information to the user This user guide helps you to understand and use your new sauna products We hope that you read this manual carefully and that you respect the warning texts The user guide is divided into two sections Information to the user and Information to the installer You as a user receive a thorough description of the workings of a sauna heater how to use the control panel and what you should keep in mind regarding maintenance If you have questions or if you need help with the products please turn to your local retailer Certain portions of the user guide are more important than others At these portions we use the following symbols A Warning ra Observe d Tips and advice a N Table of contents for the user The control panel and included parts ee 4 Functions of the control panel Set the time and chose the language 0 6 Set the Start time cnsccccaiencacweciecaecociees 7 Set the temperature eccececc eee eeeeeeeeeeeeeeeeeee 8 Set the duration oo eee eeeeeeceeeeeeeeeeeeeeeneeeeeneeeees 8 Program and activate the memory buttons 9 Change the settings during the sauna bath 10 Calibrate the temperature eect eeeeee 11 Activate Smartsauna Lock the control panel Lock fan or lighting eee eee eee eeeeeeeeeeees Connect th
10. ttons 5 Approve the start time rog ok with the button prog ok The display shows 1830 70 C 01 30 6 Start the heater by pushing prog ok for three seconds Ne D4 2 Set the tempera ture The temperature is the tempera ture that the heater produces in the sauna for example 80 C 1 Push the button for the temperature The display shows TEMPERATURE 70 C 2 Set the temperature with the arrow buttons WwW for example 80 C 3 Approve the tempera ture with the button prog ok prog ok The display shows 1830 4 80 C 01 30 4 Start the heater by pushing prog ok for three seconds Control panel Digi II XX A Turn on the 4 lightning 1 Push the button for lighting The display shows e N J 3 S Set the duration Duration is the time that the heater will operate Maximum duration is six hours 1 Push the button for start time The display shows ON TIME 01 30 2 Enter duration with the arrow buttons for example 30 minutes 3 Approve the duration with the button prog ok The display shows 1830 i 80 C 01 30 4 Start the heater by pushing prog ok for three seconds N Pi Activate ventilation 1 Push the button for ventilation The display shows J Control panel Digi II Program and activate the m
11. uld sit 4 2 x 13 mm in the holes and screw the control panel in place panel so that it is placed right before the lid is put back on basic settings Program the control panel The basic settings are to be done by the installer They include setting the clock and choosing the language After a power failure of more than 20 minutes the basic settings are deleted In that case the user must reset the basic settings Instructions to program the basic settings of the control panel are to be found on page 6 Control panel Digi II Open the lid of the control panel by inserting the control panel openers on the side The installer must set the basic settings They are found at page 6 15 o a S 3 S e fa gt z Saunatec PL 72 02201 ESPOO Finland PL 15 10901 HANKO Finland Homepage www saunatec fi E mail info saunatec fi 314 SYRA 13A Produced by Conclusion Sweden AB
12. utton prog ok for three seconds 2 Page to the menu 3 with the button prog ok aa 3 Calibrate the temperature with Aa the arrow buttons wW 4 Approve the temperature with the button prog ok 7 Calibrate the temperature s D Activate Smartsauna Smartsauna is a function that measures the temperature in the sauna and computes the length of time the heater will take to heat the sauna to the temperature that is set on the control panel The function only works when it is activated and in conjunction with a time setting Example You have had a hard day at work and wish to relax with a sauna bath directly when you come home When you arrive home at 16 00 you want the sauna to be ready for you By activating the function Smartsauna the control panel computes when the heater should start in order to warm up the sauna to the temperature you have chosen on the control panel Make sure that the control panel is in Off mode before you activate Smartsauna 3 Chose Smartsauna ON with a the arrow buttons WwW 1 Push the button prog ok for three seconds 2 Page to the menu 4 with the button prog ok 4 Approve the activation with the button prog ok 7 Activate Smartsauna lt J 11 Control panel Digi II Lock the control panel When a control panel is locked ia Lock the control panel N itis not possibleto startthe Make sure that the control panel is in Off heater This might be
Download Pdf Manuals
Related Search