SHOWER WALL INSTALLATION MANUAL
Contents
1. position on the floor and take the lath off the floor Figure 2 Andrese Klaasi ja Dekoori AS Betooni 7 9 Tallinn 11415 Place the telescopic tube as follows Fill U lath edges with even silicone stripe inside the shower room Clean the floor surface under the lath using spirit or acetone Remove protective film from the U lath s double sided tape and place the lath on the floor in to the marked position Press the lath strongly and evenly during about 30 sec Make an even silicone stripe with 6mm diameter in the U laths fixed on the wall and on the floor Figure 3 Figure 3 Place the shower wall glass in U laths and press it towards the wall so that silicone should stick the glass Figure 4 Do not push the glass too strongly towards the U lath fixed on the wall as this may cause glass break up With the help of level ensure vertical position of the glass edge Figure 5 If necessary place auxiliary wedges between glass and U lath Remove excessive silicone extruded out of the laths Hi Figure 4 Figure 5 e The tube should be at right angles to the wall and it should be fixed on the glass at a maximum distance of 20cm from the glass corner Figure 6 e In order to fasten the tube you need to drill a dowel hole in the wall 8mm depth 45 50mm the hole s center should be situated 17mm above the upper edge of glass Push the dowel into the hole and ensure t2. wall you should consider the width of shower door 80 or 90cm Measure off 79cm door width 80cm or 89cm door width 90cm from the shower room corner and mark the wall If you install the shower wall without door you can choose the distance between the U lath and the wall at your discretion 79cm 100cm 2 With the help of level place the longer U lath on the wall vertically U lath s edge should be on the same level with marked dot and U lath s end should rest against floor Figure 1 Mark the lath s holes on the wall and take the lath away from the wall if the marks are on edges of ceramic tiles try to turn the lath and make new marks 3 Drill holes in marked places 05mm depth 30 35mm Do not use drill s percussion mode in order to avoid tile break up Then blow dust off the holes push the dowels into the holes and ensure that the outer end of dowel does j not jut out of the wall Figure 1 4 Place the lath on the wall and fix it with screws 5 Place the shorter U lath on the floor set lath s end against the U lath fixed on the wall Place the U lath in parallel with the opposite wall at a distance of 79cm door width 80 cm or 89cm door width 90cm from the wall Figure 2 If you install the shower wall without door the distance between the shorter U lath and the opposite wall should be the same as the distance between the U lath on the wall and the opposite wall Mark the lath s
3. SHOWER WALL INSTALLATION MANUAL The wall package contains Following instruments are necessary 1 Glass 1 Measuring tape 2 U laths long and short 2 Level 3 Telescopic pipe set 3 Drill perforators 5mm and 8mm 4 Silicone 4 Silicone pistol 5 U lath fastening screws 3 5x30 dowels 5x25 5 Screwdriver 5 pes 6 Marking tool e Incase of frosted glass if you install a right handed door in addition to the shower wall leave the frosted side to the outer side of the shower corner If you install a left handed door in addition to the shower wall leave the frosted side to the inner side of the shower corner e Shower wall must be installed by two persons e The glass edge should in no circumstances contact tough floor or wall as this may cause glass break up e This manual assumes shower room walls to be straight and perpendicular If the walls are not straight and perpendicular the measurements mentioned in this manual should be changed according to actual situation when installing the shower cabin e Maximum allowed floor slope is 1 m 1m 1m e The shower cabin can be installed on floor as well as on shower base with appropriate size e Before drilling holes in wall check that there are no wires or water pipes in drilling place e The supplied dowels may be used only on stone walls If the wall is made of plasterboard or some other material special dowels should be used 1 When installing the shower
4. hat the outer end of dowel does not jut out of the wall e Fix the telescopic tube wall plug on the wall Figure 6 e Place one end of the telescopic tube into the wall plug and the other end on the upper edge of glass Be sure to place cushions supplied with the tube between the glass and tube brace in order to avoid contact between glass and metal e With the help of level ensure vertical position of glass and then fix the tube Figure 7 Remove excessive silicone Silicon shall dry completely in 24H Do not spill water over silicone until it is completely dry Figure 7 Telefon 6 061 320 Faks 6 061 332
Download Pdf Manuals
Related Search