User's Manual
Contents
1. 5 Select Chinese Post data redundant check options to appoint the times for data check on Chinese Post Code decode O Off turn data redundant check off O 173 select from 1 to 3 data redundant checks 6 Select Min Length options to set the minimum code length 1 64 select from 1 to 64 as the length 7 Select Max Length options to set the maximum code length 0 1764 select from 1 to 64 as the length 27 EZ Set User s MANUAL Data Editing Data Editing allows you to change the data formats of the barcodes Interface Function Symbology Data Editing System Terminal Window About Identifier Code Disable C Add code length as header enable Identifier Code Header and Trailer Header Coti I I IL I IE IE 1 CE I I JE JE JE Truncate Header Truncate Trailer 0 v 0 v C Function Key Emulation To manage Data Editing settings 1 2 3 Connect the scanner using EZ Set Click the Data Editing tab on top to go to the Data Editing menu Select the Identifier Code options to change the Identifier Code format Disable disable Identifier Code function 0 ZEBEX Format use ZEBEX default Identifier 8 AIM Format use AIM default Check or uncheck the Add code length as header enable check box to enable or disable adding length of Identifier Code as Header Select options from the cells in H2. Sleep Beeper EZ Set 12 User s MANUAL To setup the Beeper Tone Setting 1 Connect the scanner using EZ Set 2 Click the Function tab on top to go to the Function menu 3 Select the Beeper Tone options Speaker disable turn off the beeper function 0 High activate high tone sound Medium activate normal tone sound Low activate lower tone sound 4 Select Beeper Sound Duration options Very Short 5 msec extreme short beep time frame 5 msec Short 20 msec short beep time frame 20 msec Medium 50 msec normal beep time frame 50 msec Long 100 msec longer beep time frame 100 msec Very Long 200 msec very long beep time frame 200 msec Very Very Long 500 msec extreme long beep time frame 500 msec 5 Select Beeper Volume options 0 Loud activate loud beep sound Medium activate normal beep sound Low activate for lower beep sound 6 Select LED Beeper Transmission options to set the timing of the LED and beeper when data transmits Before light and beep before data transmission After light and beep after data transmission 7 Select Power up Tone options Enable activate beep on power up 0 Disable deactivate beep on power up 8 Select Sleep Beeper options to beep when entering sleep mode Sleep Silent deactivate beep on sleep mode Sleep Sound activate beep on sleep mode 13 EZ Set User s MANUAL Sleep Timeou
3. WARNING This computer program is protected by copyright law and international treaties Unauthorized duplication or distribution of this program or any portion of it may result in severe civil or criminal penalties and will be prosecuted to the maximum extent possible under the law Cancel 3 Click Browse to select the location your want to install the program in and click Next ig EzSet v1 20 Select Installation Folder The installer will install EzSet v1 20 to the following folder To install in this folder click Next To install to a different folder enter it below or click Browse Folder C Program Filesebex EzSet v1 20 Install E2Set v1 20 for yourself or for anyone who uses this computer O Everyone G Just me EZ Set 2 User s MANUAL 4 Continue to follow the on screen instructions and click Next to continue installation ig EzSet v1 20 Confirm Installation 5 Click Close when the installation is done ig EzSet v1 20 Installation Complete EZ Set User s MANUAL Overview Refer to the following illustrations to familiarize yourself with the user interface Main Menu Use the Main Menu to find the scanner you want to configure and to setup the PC COM port for connection EzSet p rod uct Handheld Scanners Hands Free Scanners In Counter Scanners Scan Modules Phase Out Category Z 3000 Handheld CCD Scanner Z 3001 Handheld Laser Scan
4. RS 232 Serial Communication vw To select the interface to use 1 Connect the scanner using EZ Set 2 Click the Interface tab on top to go to the Interface menu 3 Select the radio button of the interface option O RS 232 Serial Communication appoint device to use RS 232 as communication interface IBM PC AT PS 2 appoint device to use PC AT or PS 2 keyboard as communication interface USB Communication appoint device to use USB keyboard as communication interface 11 EZ Set USER S MANUAL Function The Function menu allows you to change the general settings of the scanner Options include Beeper Tone Setting Sleep Timeout Selection Inter Delay and Scan Mode Interface Function i Symbology Data Editing System Terminal Window About Beeper Tone Setting Sleep Timeouts Selection Scan Mode Beeper Tone Motor Sleep Time Scan Mode Trigger Mode v Medium v Beeper Sound Duration Laser Sleep Time Off v Medium 50 msec Beep Volume Inter Delay Same Code Delay Time 300 msec v Inter Character Delay Loud v LED Beeper Transmission Before v Power up Tone 0 ms v Inter Message Delay Enable Sleep Beeper 0 ms v Beeper Tone Setting Beeper Tone Seating Beeper Tone Lina ae Beeper Sound Duration Medium 50 msec Beep Volume LEQ Beeper Transmission Before Power up Tone Enable we
5. 13 first 0 ID code same as EAN 13 radio button to display F as ID Code 9 Select the Data Redundant Check options to appoint the time for data check on EAN 13 decode O Off turn data redundant check off O 173 select from 1 to 3 data redundant checks EAN 8 To manage EAN 8 settings Connect the scanner using EZ Set 2 Click the Symbology tab on top to go to the Symbology menu 3 Select the EAN UPC option to enter the settings screen 4 Check or uncheck the EAN 8 enable check box to enable or disable EAN 8 decode function 5 Check or uncheck the Transmit EAN 8 check digit enable check box to enable or disable EAN 8 check digit function 6 Select the Data Redundant Check options to appoint the time for data check on EAN 8 decode O Off turn data redundant check off O 173 select from 1 to 3 data redundant checks 17 EZ Set User s MANUAL UPC A To manage UPC A settings 1 Connect the scanner using EZ Set 2 Click the Symbology tab on top to go to the Symbology menu 3 Select the EAN UPC option to enter the settings screen 4 Check or uncheck the UPC A enable check box to enable or disable UPC A decode function 5 Check or uncheck the Transmit UPC A check digit enable check box to enable or disable UPC A check digit function 6 Check or uncheck the Transmit UPC A leading character enable check box to enable or di
6. Setting Setting Wedge setting USA ba Message terminator Enter w Alphabet Cl CapsLock enable C Function Key Emulation C Send Number as keypad To setup the Keyboard 1 2 3 EZ Set Connect the scanner using EZ Set Click the Interface tab on top to go to the Interface menu Select the Keyboard Wedge setting to appoint device to simulate the selective international keyboard function Select the Message terminator option to select the terminating character to attach after data is transmitted by Keyboard Wedge interface None do not use any terminating character Enter use Enter as terminating character H tab use Tab as terminating character CR LF 10 User s MANUAL 5 Select the Alphabet option to set the font format when simulate in keyboard interface Follow as keyboard defined according to keyboard set up e Always upper case always use capital letters 0 Always lower case always use small letters 6 Check or uncheck the CapsLock enable option to appoint device to simulate Caps lock function under Keyboard Wedge Interface 7 Check or uncheck the Function Key Emulation option to appoint device to simulate Function Key function under Keyboard Wedge Interface 8 Check or uncheck the Send Number as Keypad option to appoint device to simulate Numeric Keypad function when sending numbers Interface Option Interface Option Interface Setting
7. check box to enable or disable the Add on format separator function 19 EZ Set User s MANUAL CODE128 Code 128 C EAN 128 enable Code128 FNC2 concatenation enable Code 128 data redundant check or y Code 128 check digit Min Length Max Length o e 62 y To manage CODE128 settings og Connect the scanner using EZ Set Click the Symbology tab on top to go to the Symbology menu Select the CODE128 option to enter the settings screen Check or uncheck the Code 128 enable check box to enable or disable Code 128 decode function Check or uncheck the EAN 128 enable check box to enable or disable EAN128 function Select Code 128 data redundant check options to appoint the times for data check on Code 128 decode O Off turn data redundant check off O 173 select from 1 to 3 data redundant checks Select Code 128 check digit options to appoint Code 128 for check digit function No check check digit not enabled Check but not transmit check digit enabled but not transmitted Check and transmit check digit enabled and transmitted Select Min Length options to set the minimum code length 1 64 select from 1 to 64 as the length Select Max Length options to set the maximum code length 0 1764 select from 1 to 64 as the length EZ Set 20 GS1 Databar RSS14 GS1 Databar GS1 Databar C 651 Databar Limited Enable C 651 Databar Expand
8. reservation and without notification The material in this guide is for information only and is subject to change without notice All trademarks mentioned herein registered or otherwise are the properties of their various ill assorted owners Copyright O 2013 All rights reserved Guidance for Printing This manual is in A5 size Please double check your printer setting before printing it i EZ Set Table of Contents HOOF Gaines IN OC oil i ACPO CG KT 0 tri a 1 FU 1 System Reduire MERE 2 nadaa dsos 1 Misa OR aone ane Os 2 OVINA ias 4 MIN MEDU aca 4 C neuration Meni srenea ae N a andre 5 Star UNE EZ SOU caimics cs ste sucdeaenaumeaues ateadeataleuncesaneunsseniosareimic E N E A E 6 Connectine the Unten AN 6 A a scutes ots ase sake a T E 6 USNE EZ SOT nere O a RS 8 Nerea TT T T E OTS 8 RS 232C Interface SOI E A ere 9 Keyboard Interface Setting USB Interface Setting oooccccccncccnnnnnnnns 10 Merce OTI da caida 11 FUNC anana ve vaucedangnsavetasete cancer SENE ENE SEERE ES RENE TISSER ER STENEDE Es 12 Beeper Tone SCUUING aaa 12 Sleep TIMEOUT Selec OM 14 SCI a aan 15 gt ES lO Soy Ao Pe O a ai 15 SUM BOISEN ea a N 16 EAN UP oa 16 COD EPS arden ee ree 20 GS1 Databar RSS14 occcononcnnncnnncccnnnnnanonnnnnnnnonnnnonanonnnnonanonnnnnnnnaonnnnnnnnoss 21 CODES Tara ita doin talados 21 CODABA ata aa 23 MSIPUESS Canina 24 MAP a ae A 25 CODES a ena ae 26 Chinese POST COn o 27 Data EOS NAS 28 SUS ta aia
9. settings A bu Connect the scanner using EZ Set Click the Symbology tab on top to go to the Symbology menu Select the CODE93 option to enter the settings screen Check or uncheck the Code 93 enable check box to enable or disable Code 93 decode function Select Code93 data redundant check options to appoint the times for data check on Code 93 decode O Off turn data redundant check off O 173 select from 1 to 3 data redundant checks Select Code93 check digit options to appoint Code 93 check digit function 0 No check check digit not enabled Check but not transmit check digit enabled but not transmitted 0 Check and transmit check digit enabled and transmitted Select Min Length options to set the minimum code length 1 64 select from 1 to 64 as the length Select Max Length options to set the maximum code length 1 64 select from 1 to 64 as the length EZ Set 26 User s MANUAL Chinese Post Code Chinese Post Code Chinese Post Chinese Post data redundant check 1 v Min Length Max Length 1 sv 16 wv To manage Chinese Post Code settings Connect the scanner using EZ Set 2 Click the Symbology tab on top to go to the Symbology menu 3 Select the Chinese Post Code option to enter the settings screen 4 Check or uncheck the Chinese Post Code enable check box to enable or disable Chinese Post Code decode function
10. 29 Terminal WINAO Wi ati 32 ADOUT aire oido ERE RD mentees 33 User s MANUAL Introduction EZ Set is a powerful software platform for supporting ZEBEX line of scanners lt provides a quick convenient means to setup and test your scanners and offers basic and advanced features with a variety of options for different applications Designed for maximum functionality EZ Set includes user friendly menus and supports different firmware versions for various scanners making configurations and updates faster and more intuitive With EZ Set users can work smarter faster more efficiently and with dramatically increased productivity Features Supports Windows XP Vista and 7 Supports real time device and barcode settings System Requirement EZ Set requires a PC with the following specifications O Windows XP Service Pack 2 or above Microsoft Internet Explorer 5 01 or later Microsoft Framework 2 0 Disk Space Requirements 2 MB One available RS 232 Serial Port 1 EZ Set User s MANUAL Installation Follow the instructions below to install EZ Set on your computer 1 Find and click the Setup file on your computer to begin installation 2 Follow the on screen instructions and click Next when prompted to continue installation ig EzSet v1 20 Welcome to the EzSet yl 20 Setup Wizard FR y a SY The installer will guide you through the steps required to install EzSet v1 20 on your computer
11. Control Pa n el Message Terminator CRLF v C CapsLock enable Interface Option DEESA C Function Key Emulation USB Communication Send Number as Keypad Function Description Select the tabs to access different functions to Function Tabs setup or test the scanner Options available in this panel changes depending on which function tab is currently Control Panel selected Options may include interface or function settings or a terminal window for scanner testing 5 EZ Set User s MANUAL Starting EZ Set Note USB connection is for firmware update only and supports only the 32 bit devices such as Z 3100 Z 3101 Z 3151HS Z 3110 Z 3190 Z 3220 Z 6170 Z 6180 Z 6182 Z 6182 Z 5111 Z 5130 and Z 5160 Connecting the Unit A power adapter may be required to power the scanner To connect the scanner to a computer 1 Connect the scanner to a RS 232 serial port or USB port on the computer 2 Make sure the unit is turned on after the cable and the power adapter is connected Starting EZ Set To start EZ Set 1 From Windows Start Menu select Programs and select EZ Set 2 The EZ Set main screen appears on the desktop Handheld Scanners Hands Free Scanners In Counter Scanners Scan Modules Phase Out Z 3060 Handheld Omnidirectional Laser Scanner Z 3100 Advanced Middle Range Handheld CCD Scanner Z 3101 Advanced Handheld Laser Scanner Z3151HS Advanced Handhel
12. PPP 10 11 25 Connect the scanner using EZ Set Click the Symbology tab on top to go to the Symbology menu Select the ITF 2 OF 5 option to enter the settings screen Check or uncheck ITF enable to enable or disable ITF 2 of 5 decode function Check or uncheck IATA enable to enable or disable IATA decode function Select ITF 2 of 5 check character options to appoint ITF 2 of 5 for check character function No check check digit not enabled 0 Check but not transmit check digit enabled but not transmitted Check and transmit check digit enabled and transmitted Select ITF 2 of 5 data redundant check options to appoint the times for data check on ITF 2 of 5 decode e Off turn data redundant check off O 173 select from 1 to 3 data redundant checks Select Min Length options to set the minimum code length 0 1764 select from 1 to 64 as the length Select Max Length options to set the maximum code length 1 64 select from 1 to 64 as the length Select One Fix Length options to set one fixed length 0 64 select from O to 64 as the length Select Two Fix Length options to set two fixed length 0 64 select from O to 64 as the length EZ Set User s MANUAL CODE93 CODE93 Code 93 data redundant check off v Code 93 check digit check but not transmit J Min Length Max Length 03 v 62 v To manage CODE93
13. User s MANUAL Terminal Window Terminal Window is used for testing Users can test device at this page to confirm settings that was done Interface Function Symbology Data Editing System Terminal Window About To use Terminal Window Connect the scanner using EZ Set 2 Click the Terminal Window tab on top to go to the Terminal Window page 3 Scan barcodes and check the page to see if the data is correct 4 Use Show Version to show the current firmware version or Clear All to clear all information on the page EZ Set 32 User s MANUAL About Information about EZ Set Click on the http www zebex com link to go to ZEBEX website or Help to access the help file Interface Function Symbology Data Editing System Terminal Window About 33 EZ Set
14. ZZEBEX www zebex com User s Manual EZ Set ZEBEX INDUSTRIES INC M Revision History Changes to the original manual are listed below November 01 2012 Initial release 1 02 March 25 2013 Updated to 1 20 version with added USB firmware update function 1 03 June 20 2013 Added USB firmware update instruction EZ Set User s Manual Important Notice No warranty of any kind is made in regard to this material including but not limited to implied warranties of merchantability or fitness for any particular purpose We are not liable for any errors contained herein nor for incidental or consequential damages in connection with furnishing performance or use of this material We shall be under no liability in respect of any defect arising from fair wear and tear willful damage negligence abnormal working conditions failure to follow the instructions and warnings or misuse or alteration or repair of the products without previous written approval from us No part of this document may be reproduced transmitted stored in a retrieval system transcribed or translated into any human or computer or other language in any form or by any means electronic mechanical magnetic optical chemical biological manual or otherwise except for brief passages which may be quoted only for purposes of scholastic or literary review without express written consent and authorization We reserve the right to make changes in product design without
15. ck the Full ASCII Code 39 check box to enable or disable Full ASCII Code 39 decode function Check or uncheck the Code 39 Start Stop character transmission check box to enable or disable Start Stop character transmission function Check or uncheck the Code 32 transmit A character check box to enable or disable Code 32 transmit A character Select Code 39 data redundant check options to appoint the times for data check on Code 39 decode O Off turn data redundant check off 0 173 select from 1 to 3 data redundant checks Select Code 39 check digit options to appoint Code 39 for check digit function 0 No check check digit not enabled Check but not transmit check digit enabled but not transmitted Check and transmit check digit enabled and transmitted Select Min Length options to set the minimum code length e 1764 select from 1 to 64 as the length Select Max Length options to set the maximum code length 1 64 select from 1 to 64 as the length EZ Set 22 User s MANUAL CODABAR Codabar Codabar concatenation enable Codabar start stop character transmission lAB C D v Codabar check character No check Codabar data redundant check off Y Min Length Max Length 06 32 w To manage CODABAR settings Connect the scanner using EZ Set Click the Symbology tab on top to go to the Symbology menu Select the CODABAR option to enter
16. d High Speed Laser Z 3190 Gun Type Handheld CCD Scanner Z 3220 Handheld Linear Image Scanner COM Port Setting COM Port Baud Rate Parity Data Bits Stop Bit com v 9600 None Y 8 EZ Set User s MANUAL 3 In COM Port Setting select USB or a COM port 4 For the COM port selection select the values from the drop down menus You must correctly set the COM Port to enter this application program The following definition will explain individual purpose 5 The definitions of the settings are as follows COM Port the port connection to host device Baud Rate the baud rate communicates between the device and host Parity checks code between the device and host Data Bits Data Bit used between the device and host Stop Bit Stop Bit used between the device and host COM Port Setting COM Port Baud Rate Parity Data Bits Stop Bit com w 9600 None w 8 O NMN 6 Use the Product Category tabs to browse different categories of scanners Handheld Scanners Hands Free Scanners In Counter Scanners Scan Modules Phase Out Z 3060 Handheld Omnidirectional Laser Scanner Z 3100 Advanced Middle Range Handheld CCD Scanner Z 3101 Advanced Handheld Laser Scanner ZS161HS Advanced Handheld High Speed Laser Z 3190 Gun Type Handheld CCD Scanner Z 3220 Handheld Linear Image Scanner COM Port Setting COM Port Baud Rate Parity com v 9600 None y 8 7 Find and select t
17. eader and Trailer as desired to append contents to header and trailer Select Truncate Header options to appoint the number of digits add or intercept in header 0 16 select from Oto 16 Select Truncate Trailer options to appoint the number of digits add or intercept in Trailer 0 16 select from Oto 16 Check or uncheck Function Key Emulation check box to enable or disable the function key emulation function EZ Set 28 User s MANUAL System The System menu is used to update firmware load parameters and issue commands to the scanner Interface Function Symbology Data Editing System Terminal Window About Firmware Update Browse Update Parameters Load Browse Load Commands Version Save Parameters Load Parameters List Parameters To update firmware using USB connection For Z 5111 Z 5130 Z 3100 Z 3101 Z 3110 Z 3220 with BootLoad H01 04 or later Z 3151HS with BootLoad 01 03 or later Z 6180 Z 6181 Z 6182 Z 6170 or other 32 bit models only 1 Connect the scanner using USB cable and start EZ Set 2 Set the scanner to USB Update using the following barcodes For 32 bit Single line scanners 1 Enter Programming Mode 2 USB Update 29 EZ Set User s MANUAL For 32 bit Omnidirectional Scanners 1 Enter Programming Mode 2 USB Update In EZ Set select USB in COM Port Setting and click the scanner model to co
18. ed Enable To manage GS1 Databar RSS14 settings Connect the scanner using EZ Set a i USER S MANUAL Click the Symbology tab on top to go to the Symbology menu Select the GS1 Databar RSS14 option to enter the settings screen Check or uncheck the GS1 Databar Standard Enable check box to enable or disable GS1 Databar decode function 5 Check or uncheck the GS1 Databar Limited Enable check box to enable or disable GS1 Databar Limited decode function Check or uncheck the GS1 Databar Expanded Enable check box to enable or disable GS1 Databar Expanded decode function CODE39 CODE39 consists of settings for Code39 and Code 32 21 Code 39 Code 32 Code 39 enable C Code 32 enable C Full ASCII Code39 C Code 39 Start Stop character transmission Code 39 concatenation enable C Code 32 transmit A character Code 39 data redundant check of ov Code 39 check digit No check Y Min Length Max Length 03 w lc i EZ Set User s MANUAL To manage CODE39 settings RO 10 11 12 Connect the scanner using EZ Set Click the Symbology tab on top to go to the Symbology menu Select the CODE39 option to enter the settings screen Check or uncheck the Code 39 enable check box to enable or disable Code 39 decode function Check or uncheck the Code 32 enable check box to enable or disable Code 32 decode function Check or unche
19. he model of the scanner to make connection Not all models of scanners are supported Please contact us if your scanner is not listed in the program 7 EZ Set Using EZ Set Once the device is connected the Configuration Menu appears The Configuration Menu is used to change the scanner settings and to test the scanner It consists of 7 tab menus Interface Function Symbology Data Editing System Terminal Window and About To access the menus simply click on the tabs Please see the follow sections for more instructions Interface The Interface menu allows users to select and setup the interfaces for connection The options include RS 232C Interface Setting Keyboard Interface Setting USB Interface Setting and Interface Option RS 232C Interface Setting Keyboard Interface Setting USB interface Setting Handshaking Setting Handshaking Wedge setting None v USA v ACKNAK Response Time 300 ms v Message terminator Enter v ACKNAK Timeout Beeper C Beep on lt BEL gt Character Alphabet Message Terminator CRLF Y C CapsLock enable Interface Option Interface Setting C Function Key Emulation USB Communication Send Number as Keypad EZ Set User s MANUAL RS 232C Interface Setting RS 2320 Interface Setting Handshaking Handshaking None we ACEINAK Response Time 300 ms w O ACKINAK Timeout Beeper Beep on BEL Character Mo 553994 Terminat
20. igit enable E Transmit UPC A leading character enable C EAN convert to ISSN ISBN enable Data Redundant Check of v C EAN 13 first 0 can transmitted enable UPC E EAN 13 first 0 ID code same as UPC AT E UPC E enable EAN 13 first 0 ID code same as EAN 13 E Transmit UPC E check digit enable Transmit UPC E leading character enable Data Redundant Check off v Data Redundant Check of EAN 8 Addon 7 EAN 8 enable O Addon 5 enable Transmit EAN 8 check digit enable C Addon 2 enable Data Redundant check or Addon format with separator enable EZ Set 16 User s MANUAL EAN 13 To manage EAN 13 settings 1 Connect the scanner using EZ Set 2 Click the Symbology tab on top to go to the Symbology menu 3 Select the EAN UPC option to enter the settings screen 4 Check or uncheck the EAN 13 enable check box to enable or disable EAN 13 decode function 5 Check or uncheck the Transmit EAN 13 check digit enable check box to enable or disable EAN 13 check digit function 6 Check or uncheck the EAN convert to ISSN ISBN enable check box to enable or disable EAN convert to ISSN ISBN decode function 7 Check or uncheck the EAN 13 first O can transmitted enable check box to enable or disable transmitting the first digit when it is 0 8 Select EAN 13 first O ID code same as UPC A radio button to display A as ID Code or select the EAN
21. mbology tab on top to go to the Symbology menu Select the MSI PLESSY option to enter the settings screen Check or uncheck the MSI enable check box to enable or disable MSI decode function Select MSI data redundant check options to appoint the times for data check on MSI decode O Off turn data redundant check off O 173 select from 1 to 3 data redundant checks Select MSI PLESSY check digits options to appoint MSI check digit function No check check digit not enabled o Single Check but not transmit single check digit enabled but not transmitted 0 Single Check and transmit single check digit enabled and transmitted Double Check but not transmit double check digit enabled but not transmitted 0 Double Check but only first digit transmit double check digit enabled but only first digit transmitted Double Check and both digits transmit double check digit enabled and both digits transmitted Select Min Length options to set the minimum code length 0 1764 select from 1 to 64 as the length Select Max Length options to set the maximum code length 1764 select from 1 to 64 as the length EZ Set 24 User s MANUAL ITF 2 OF 5 ITF 2 of 5 ITF enable C IATA enable ITF 2 of 5 check character No check ITF 2 of 5 data redundant check cr Min Length Max Length 06 4 32 w One Fix Length Two Fix Length oo oo To manage ITF 2 OF 5 settings of B
22. ner Z 3010 Contact CCD Scanner Z 3021 Handheld Laser Scanner Z 3051HS High Speed Handheld Laser Scanner Z 3110 Advanced Handheld Contact CCD Scanner CT 131 Scan Module Product A 30M Scan Module Models A 62M COM Port Setting CO M Po rt COM Port Baud Rate Parity Data Bits Stop Bit v 9600 v None 8 Setting ZEBEX EZ Set is the configuration software for ZEBEX scanners ZEBEX ARS 232 serial cable is required for connecting the scanner and the host www zebex com To start configuration select your COM port setting and then the model to be set up Function Description Select the tabs to switch between different Product Category product types Select the scanner model to connect to the scanner you want to configure Options change depending on which product category is currently selected Used to setup the COM port of the PC so the scanner can be connected Product Models COM Port Setting EZ Set 4 User s MANUAL Configuration Menu Use the Configuration Menu to configure settings including interface function and symbology and to test the scanner Function Tabs RS 232C Interface Setting Keyboard Interface Setting USB interface Setting Handshaking Setting Handshaking Wedge setting None v USA v ACKNAK Response Time n Message terminator 300 ms v Enter v ACKNAK Timeout Beeper C Beep on lt BEL gt Character Alphabet
23. ngs 1 Connect the scanner using EZ Set 2 Click the Function tab on top to go to the Function menu 3 Select Same Code Delay Time options to appoint the time interval between reading the same data 0 50msec 1 000msec selection from 50 millisecond to 1 second Infinite do not send data if reading the same barcode 4 Select the Inter Character Delay options to appoint the time interval between characters when transmitting data e Oms 30ms select from 0 millisecond to 30 millisecond 5 Select the Inter Message Delay options to appoint the time interval between messages when transmitting data O Oms 1000ms select from O millisecond to 1000 millisecond 15 EZ Set User s MANUAL Symbology The Symbology menu allows you to change the barcode settings of the scanner Select a barcode name to enter the settings screen Options include EAN UPC Jan CODE39 CODE 128 ITF 2 OF 5 CODABAR CODE 93 Chinese Post Code MSI PLESSY and GS1 Databar RSS 14 Interface Function Symbology Data Editing System Terminal Window About Symbology Setting EAN UPC JAN CODE 128 GS1 Databar RSS 14 CODE 39 CODABAR MSI PLESSY ITF 2 OF 5 CODE 93 Chinese Post Code EAN UPC EAN UPC consists of different settings for EAN 13 EAN 8 UPC A UPC E and Addon EAN UPC EAN 13 UPC A EI EAN 13 enable UPC A enable Transmit UPC A check digit enable f Transmit EAN 13 check d
24. nnect the scanner Click the System tab on top to go to the System menu Select Browse to locate the new firmware file Select Update to update the firmware To update firmware using RS232 connection Connect the scanner using RS232 cable and start EZ Set In EZ Set select the appropriate COM port in COM Port Setting and click the scanner model to connect the scanner Click the System tab on top to go to the System menu Select Browse to locate the new firmware file Select Update to update the firmware To load saved parameters from host PRE Connect the scanner using EZ Set Click the System tab on top to go to the System menu Select Browse to locate the save parameter file Select Load to download settings to device EZ Set 30 User s MANUAL To send commands to the scanner 31 Connect the scanner using EZ Set Click the System tab on top to go to the System menu Select options in the Commends section to issue commands to the scanner Reset select this option to reset the scanner to factory default Version select this option to view the current firmware version Sleep send the scanner to the sleep mode Wake Up wake the scanner up from sleep mode Save Parameters save all parameter made during current set up process Load Parameters load other parameter set up files from host files List Parameters list current parameters being used EZ Set
25. or GRULF a To setup the RS 232C Interface Setting 1 2 3 Connect the scanner using EZ Set Click the Interface tab on top to go to the Interface menu Select the Handshaking options 0 None handshaking not required O ACK NAK activate ACK NAK for handshaking o XOn XOff activate XOn XOff for handshaking Oo RTS CTS activate RTS CTS for handshaking Unit in character Select the ACK NAK Response Time options 300ms Designate time out time is 300 millisecond 500ms Designate time out time is 500 millisecond 1 sec Designate time out time is 1 second 2 sec Designate time out time is 2 second 3 sec Designate time out time is 3 second 5 sec Designate time out time is 5 second Infinity Designate time out time is infinity Check or uncheck the ACK NAK Timeout Beeper check box to select whether to use beep notify when a timeout is reached and ACK NAK handshaking fails Check or uncheck the Beep on lt BEL gt Character check box to select whether to beep when device receives lt BEL Ox07 gt character Select the Message Terminator options to select the terminating character to attach after data is transmitted by RS 232 interface None do not use any terminating character CR LF EZ Set User s MANUAL CR LF H tab use Tab as terminating character STX ETX EOT Keyboard Interface Setting USB Interface Setting Keyboard Interface Setting USE Interface
26. sable UPC A leading character function 7 Select the Data Redundant Check options to appoint the time for data check on UPC A decode Off turn data redundant check off 0 173 select from 1 to 3 data redundant checks UPC E To manage UPC E settings 1 Connect the scanner using EZ Set 2 Click the Symbology tab on top to go to the Symbology menu 3 Select the EAN UPC option to enter the settings screen 4 Check or uncheck the UPC E enable check box to enable or disable UPC E decode function 5 Check or uncheck the Transmit UPC E check digit enable check box to enable or disable UPC E check digit function 6 Check or uncheck the Transmit UPC E leading character enable check box to enable or disable UPC E leading character function 7 Select the Data Redundant Check options to appoint the time for data check on UPC A decode O Off turn data redundant check off O 173 1 to 3 data redundant checks EZ Set 18 User s MANUAL Addon To manage Addon settings 1 Connect the scanner using EZ Set 2 Click the Symbology tab on top to go to the Symbology menu 3 Select the EAN UPC option to enter the settings screen 4 Check or uncheck the Add on 5 enable check box to enable or disable Add on 5 function 5 Check or uncheck the Add on 2 enable check box to enable or disable Add on 2 function 6 Check or uncheck the Add on format with separator enable
27. t Selection Bleep Time ouis Selection Molor Sleep Time Laser Sleep Time To manage the Sleep Timeout Selection 1 Connect the scanner using EZ Set 2 Click the Function tab on top to go to the Function menu 3 Select Motor Sleep Time options to appoint the motor to enter sleep mode after time out Off disable this function 5min enter sleep mode after 5 minutes 10min enter sleep mode after 10 minutes 20min enter sleep mode after 20 minutes 30min enter sleep mode after 30 minutes 60min enter sleep mode after 60 minutes 4 Select Laser Sleep Time options to appoint the laser to enter sleep mode after time out Off disable this function 5min enter sleep mode after 5 minutes 10min enter sleep mode after 10 minutes 15min enter sleep mode after 15 minutes 20min enter sleep mode after 20 minutes 30min enter sleep mode after 30 minutes 60min enter sleep mode after 60 minutes EZ Set 14 User s MANUAL Scan Mode Scan Mode Scan Mode Trigger Mode we To setup the Scan Mode 1 Connect the scanner using EZ Set 2 Click the Function tab on top to go to the Function menu 3 Select the Scan Mode options Trigger Mode set the scanner to Trigger Mode Auto Scan Mode set the scanner to Auto Scan Mode Inter Delay Inter Delany Same Code Delay Time 500 msec e Inter Character Delay ms w inter Message Delay mg a To setup the Inter Delay setti
28. the settings screen Check or uncheck Codabar enable to enable or disable Codabar decode function Select Codabar start stop character transmission options to appoint Codabar start stop transmit character oe oe DO 0 None start stop character transmission not enabled O A B C D start stop character transmission with A B C D O DC1 DC4 start stop character transmission with DC1 DC4 a t b n c d e start stop character transmission with a t b n c 6 Select Codabar check character to appoint Codabar check character function 0 No check check digit not enabled Check but not transmit check digit enabled but not transmitted 0 Check and transmit check digit enabled and transmitted 7 Select Codabar data redundant check options to appoint the times for data check on Codabar decode O Off turn data redundant check off O 173 select from 1 to 3 data redundant checks 8 Select Min Length options to set the minimum code length 0 1764 select from 1 to 64 as the length 9 Select Max Length options to set the maximum code length 1 64 select from 1 to 64 as the length 23 EZ Set User s MANUAL MSI PLESSY HSI PLESSY MSIPLESSY MSI data redundant check oo MSVPLESSY check digits double check but not transmit v Min Length Max Length 04 v 32 v To manage MSI PLESSY settings oS 8 Connect the scanner using EZ Set Click the Sy
Download Pdf Manuals
Related Search