FT5X Installation And User Manual
Contents
1. 10 lock the service provider 01 PIN code error 00 IMSI error Red Fast Flash serious error Error Code by Network and Inuse indicators Red defined as 1 Dark defined as 0 00 need PUK code 01 GSM baud rate error 10 other errors 5 31 FT5X User Guide 2 3 Hardware Installation Steps 1 Unscrew the SIM cover on the underside of the FT5X remove the cover insert a SIM and then reattach the SIM cover Replace the screw 2 Connect a regular telephone into the socket marked Phone indicated on FT5X back plane 3 Connect a G3 Fax machine into the socket marked Fax indicated on FT5X back plane A Caution Do NOT plug external line into Telephone socket or it may cause device damage 4 Connect a telephone line to the socket marked PSTN on FT5X back plane 5 Connect and screw up firmly the included antenna onto SMA terminator marked Y indicated on FT5X back plane 6 Make sure power switch on the back plane is in OFF position Afterwards plug one end of included power adapter into power socket and plug the other end into DC12V power interface indicated on the back plane TS Switch on power when the Status indicator turns dark and the Network indicator lights continuously The system goes into normal network registration succeed The device is ready to use 8 Shut down the device Press the power switch 3 to 5 seconds release the power switch the Power and Network2. Command 61 DN BS Description GSM divert when no reply GSM divert No Signal Command 62 DN BS Description GSM divert if there is no signal in service area GSM divert all calls Command 002 DN BS Description GSM diverting all calls GSM diverting All Terms Command 004 DN BS Description GSM diverting call under all terms GSM outgoing call limiting Command 33 PW BS Description GSM outgoing calls are limiting GSM international call restriction Command 331 PW BS Description GSM restrict the outgoing international call GSM international call restriction except the homeland Command 332 PW BS Description GSM restrict all the international call except the homeland GSM all incoming call restriction Command 35 PW BS 27 31 FT5X User Guide Description GSM restrict all the incoming call 11 GSM all incoming call restriction roam Command 351 PW BS Description GSM restrict all incoming call during roaming 12 GSM enable disable call waiting Command 43 Description GSM enable disable call waiting function 28 31 FT5X User Guide 4 Frequently Asked Questions Q how long do I wait till I am able to make a phone call or a fax A switch on power when the Status indicator turns dark and the Network indicator lights continuously The system goes into normal network registration succe
3. Indicating device not powered on or starting up The STATUS indicator is still OFF within 15 seconds when turn on the device and then the indicator becomes slowly flashing Indicators instruction 1 Power Power supply indicator two color indicator 1 Green external power supply 2 Red battery supply 3 Dark no power supply 4 31 FT5X User Guide www microdata fi support microdata fi 2 3 4 1 2 3 4 5 1 2 3 4 5 1 2 3 4 Network Network indicator two color indicator Green Slow Flash searching network Green Fast Flash voice SMS but don t support voice mail Green Connect to network strong signal Red connect to network weak signal Dark network registration failed Inuse phone fax data indicator two color indicator Green Indicating the status of talking or hanging up Red Indicating the status of Fax function Dark Indicating the status of Free Green Fast Flash Indicating a call in and ringing Red Fast Flash Indicating a fax in and ringing Status status indicator two color indicator Dark normal operation Green general error Error Code by both Network and Inuse indicators Red defined as 1 Dark defined as 0 00 no SIM card 11 input PIN code Red lock device lock SIM card lock the service provider lock cell Error Code by Network and Inuse indicators Red defined as 1 Dark defined as 0 11 lock cell
4. OK Q When I use GSM fax is it possible to fax like desktop fax machine i e make a phone call before sending faxes A Not possible FT5X does not support GSM voice fax switch over function This function requires GSM GPRS network supporting TS61 allowing user to make phone call while faxing So when sending faxes please press down Start key immediately after complete your number when receive faxes please set fax machine to Auto receive mode 29 31 FT5X User Guide WARRANTY Dear User Thank you for choosing the fixed wireless terminal of our company In order for you to enjoy our complete service please read the following warranty conditions carefully Product warranty conditions From the date you purchased this product unless otherwise damaged by intention we Offer one 1 year free of charge warranty Warranty starts from the date of purchase which is indicated on invoice In case of no such invoice available warranty starts from production date Within 15 days from purchasing if not intentionally damaged the product could be claimed for a change with Warranty card or Invoice If the product is defective user must bring with the product to the distributor or dealer by himself or herself to make a change or repair or go to the local customer service center to make a change or repair Warranty Notes Warranty is subject to normal operation of the product Any man made intentional damage including but not
5. and change the modems Maximum Speed to 115200bps Click OK When prompted for a Username and Password enter the Username and Password provided by the Network Operator When prompted for a phone number use the following number for a GPRS connection exactly as it appears here 22 31 FT5X User Guide 4 4 Telephone Keypad Configuration Commands User may enter commands by using telephone keypad of a telephone connected to the Phone socket on the back panel of the unit as follows 1 Lift Receiver 2 Enter Command a confirmation tone will then be heard 3 Replace Receiver 4 4 1 System Configuration 1 Set work mode Command 1 working mode Description Set the work mode of terminal Working mode 0 is voice mode lis voice fax mode 2 is PBX relay mode 3 is PBX extension access mode Set dial mode command 333 n Description set the terminal dialing mode n 0 is audio dial mode n 1 is pulse dial mode Set system date Command 20 y m d Description Set the system date y means 00 99 m means month 0 12 d means day 0 31 Set system time Command 21 h m s Description Set the system time of the device h means hour 0 24 m means minute 0 59 s means second 0 59 Set auto dialing delay Command 3 seconds Description Set up dialing overtime and auto sending out time upon completely entry of numbers default setting 3 seconds lt seconds gt Set point range 1 20 sec Set ext
6. battery e Airtime 2 3 hours depend on the Networks when use battery e Charging Time 12 hours for the first time 8 hours thereafter Port interface e RJ11 Fax and Phone port 2RJ11 PSTN port 1RJ11 e RS232 DB9 port e GSM Antenna TNC female 50Q e SIM card 3V SIM card Phone port e Impedance 27092 750 150nF default e Open circuit voltage OCV 50V Con hook e Feed current 25mA off hook e Ringing Load Supports integrating 3 phones 3REN e Provides polarity reversal Working Environment e Operating temperature O0 C 45 C e Operating humidity 20 75 e Storage temperature 20 C 60 C e Storage Humidity 5 95 Dimensions e LengthxWidthxHeight 20cmx15cmx4cm e Weight 0 5kg 1 3 Safety 1 3 1 Safety using this product 1 Please avoid using wireless telephone and fax functions of this product in areas where wireless transmission equipment is restricted such as hospitals health care facilities and on board aircraft 2 Please avoid using wireless telephone and fax functions of this product in gas stations bunkers and places of chemical storage 3 Please avoid using wireless telephone and fax functions of this product in chemical plants 2 31 FT5X User Guide www microdata fi support microdata fi or any other places with hazard of explosion such as gas leakage site Please avoid using this product on any metal surface that might weaken power of received signal Please avoid using PSTN netwo
7. FT5X User Guide www microdata fi support microdata fi FTSX Installation And User Manual 1 OVERVIEW 1 1 Product Features Supports dual mode voice access Mobile network GSM and Telecom PSTN GSM Fax function GSM data function Supports traditional PBX access Dynamic echo cancellations to ensure the perfect voice quality Off power bypass functions when power is off system switches to PSTN network automatically Modem mode Access the Internet by GPRS through the PC serial port Supports the phone book stored in the SIM card or in the terminal Intelligent routing Able to set up dialling regulation to route voice or fax intelligently Setup by Keyboard prompt line for convenient operation Incoming caller display function Auto dialing function Internal calling divert function Real time displaying of wireless network signal power Support POS connection depend on the networks Software upgrade 1 31 FT5X User Guide www microdata fi support microdata fi 1 2 Technical Specification Frequency Bands e EGSM 900 GSM1800MHz Transmission Power e EGSM 900 Class4 2W Peak e GSM 1800 Classi 1W Peak Frequency Range e EGSM900 890 915 MHz 935960 MHz e GSM 1800 1710 1785 MHz 1805 1880 MHz Power Consumption e Average power consumption lt 5W Power Supply e Output DC12V 1000mA e Input 100 240V AC 50 60Hz Battery backup e Lithium 3 7v 1700mAh e Standby Time 12 18 hours depend on the Networks when use
8. User Guide 4 3 2 4 Setting up GPRS The following are additional steps that need to be carried out in order to use the FT5X unit with GPRS To connect to the internet via GPRS the FT5X requires a GPRS enabled SIM Card and the following information must be provided by the Network Operator e Access Point Name APN e Username e Password Increase port speed and add Advanced Settings Click Start Settings Control Panel Double click Phone and Modem Options Click on the Standard 33600 bps Modem and click Properties Standard 33600 bps Modem Properties es General Modem Diagnostics Advanced Driver Port COM10 Speaker volume Maximum Port Speed mao D Dial Control Change the Maximum Port Speed setting to 115200 Click on the Advanced tab 21 31 FT5X User Guide Standard 33600 bps Modem Properties General Modem Diagnostics Advanced Driver Extra Settings Extra initialization commands Change Default Preferences Under Extra initialisation commands enter the following text exactly as it appears here AT CGDCONT 1 IP APN Where APN is the access point name provided by the Network operator Click OK to confirm the settings Click OK to exit the Phone and Modem options screen Configure connection Refer to the section 4 3 2 Connecting to the Internet for instructions on setting up an internet connection Right click the connection and choose Properties Click Configure
9. character string the user will need to change the current standard of caller ID identification by command 81 n Set the device to support the three different standards of caller ID identification Command 81 n Description Set the device to support the three different standards of caller ID identification O Off 1 ETSI DTMF 2 ETSI V 23 3 Bellcore Default value is 3 Set keyboard command for transmitting caller ID during calling Command 82 n Description Set keyboard command for whether or no transmitting caller ID during calling O No transmit 1 Transmit Set Serial port Mode Set serial port mode Command 83 n Description Set serial port mode O Off 1 CLI 2 MODEM SIM Card settings Input PIN code Command 86 n Description Input PIN code n is the PIN code which input by user Modify PIN code Command 88 oldpin new newV Description Modify PIN code The Oldpin is old PIN code the New is new PIN code the NewV is confirm new PIN code Input PUK code Command 89 PUK PIN Description Input PUK code PUK is input by user PIN is new PIN code input by user Set PIN code function Command 90 n pin Description Set PIN code function n 0 Disable PIN function n 1 Enable PIN function 25 31 FT5X User Guide 4 4 7 4 4 8 Hotline call number Set the hotline call number Command 65 hotlineNumber Description Set the hotline call number hotlineN
10. click Control Panel amp Control Panel File Edit View Favorites Tools Help x pe Search gt Folders A Address Control Panel Go a D A amp Vg R E P S Control Panel A Pad LiveUpdate Mail Mouse Network a b amp amp NVIDIA nview Aae Power Options Printers and Windows Update Desktop M Modem axes F Options Help and Support v i T P s 6 Regional and Scannersand Scheduled Sounds and Language Cameras Tasks Audio Devices See Also Note If the screen displayed differs to that shown here click Switch to Classic View Double click Phone and Modem Options Phone and Modem Options Dialing Rules Modems Advanced B gt The following modems are installed Modem Attached To Remove Properties Select the Modems Tab Click Add 14 31 FT5X User Guide Add Hardware Wizard Install New Modem E Do you want Windows to detect your modem a Windows will now try to detect your modem Before continuing you should 1 If the modem is attached to your computer make sure it is turned on 2 Quit any programs that may be using the modem Click Next when you are ready to continue Select Don t detect my modem I will select it from a list Click Next Add Hardware Wizard Install New Modem f Select the manufacturer and model of your modem If your modem is not listed or if you have an installation disk click Have Disk Ma
11. cting to the Internet It is assumed that an Internet account has already been set up with a service provider You will have been given e Telephone number for the dial up connection e Username and Password From the Start Menu click Control Panel amp Control Panel DER Ax File Edit View Favorites Tools Help Bach gt B pe Search gt Folders Ez Address J Control Panel m Va Control Panel 9 8 J Game Internet Java Plug in Keyboard B Switch to Category View Controllers Options iad KD See Also 5 LiveUpdate Windows Update Help and Support A NVIDIA nyiew Phone and Power Options Printers and Desktop M Faxes Double click Network Connections Click Create A New Connection Click Next New Connection Wizard Network Connection Type What do you want to do Connect to the Internet Connect to the Internet so you can browse the Web and read email Oc Connect to a business network using dial up or YPN so you can work from home a field office or another location O Set up an advanced connection Connect directly to another computer using your serial parallel or infrared port or set up this computer so that other computers can connect to it Select Connect to the network at my workplace and click Next 18 31 FT5X User Guide New Connection Wizard Network Connection How do you want to connect to the network at your workplace Create the following connec
12. ed Q What will happen if I make a wrong connection to Telephone socket and PSTN socket A No mistake is allowed for connections of Telephone socket connecting telephone and External line socket TRUNK Wrong connection may cause system failure and may cause permanent damage to the unit Q Why does the device always send the FAX as a voice outgoing call A Some outdated FAX cannot send the identification tone the user must add the 01 before the number to prompt the system this call is FAX call Such as 01 Number Q Why does the device always make the voice outgoing call when user makes the data call A Some outdated Modem cannot send the CNG identification tone so the user should add the Q2 before the number to prompt the system this call is Data call Such as 0O20 Number Q Is it possible to transmit fax via GSM by any SIM card A Before using GSM fax function the user makes sure that a For sending faxes ensure SIM card data transmission service is available GSM network support is required b For receiving ensure SIM card fax receiving service is available GSM network support is required usually this function needs dual number with one SIM card one voice number and one fax number For fax receiving only fax number is used Voice number is not expected for fax receiving Q What type of fax machine do I need to use A FT5X is in line with G3 fax criteria Any compatible G3 standard fax machine is
13. ernal line flash key delay Command 4 lt flashDelay gt Description Set external line flash key delay default 700ms delay lt delay gt 0 2000 ms Set GSM output voice volume Command 53 volume Description Set GSM output voice volume volume 0 4 Set overtime of Button R Command 85 n Description Set overtime of Button R This feature is only available in the SIM card used by the open call waiting function effectively Default 2 seconds lt n gt 1 5 seconds 23 31 FT5X User Guide 9 Set FAX and Voice Ring both Command 68 n Description Set FAX and Voice Ring both when n is 0 means off and 1 means o This function is NO effective on the hardware board version 2 0 10 Minute Prompt Command 110 n Description n 1 the device will send a prompt tone per one minute during user s conversation n 0 Off this function 4 4 2 Fax mode configuration 1 Set fax receive mode Command 63 n Description n O fax receiving mode is Synchronization n 1 fax receiving mode is Asynchronous Default n 0 2 Set fax send mode Command 64 n Description n 0 fax sending mode is Synchronization n 1 fax sending mode is Asynchronous Default n O 4 4 3 Call Diverts 1 Set the divert number from FXO to GSM Command 71 Number Description Set the divert number from FXO to GSM Number is the number which dialed from GSM port 2 Set the appointed incoming call number by FXO Command 72 number D
14. escription Set the appointed incoming call number by FXO When the incoming call number is the appointed number on FXO port the device will looks this incoming call as special call 3 Clear the incoming call number appointed by FXO Command 73 Description Clear the appointed incoming call that has been set 4 Set no answer delay for FXO Command 74 time Description Set no answer delay time for FXO 5 Set the FXO call diversion type Command 75 n Description Set the FXO call diversion type O divert always 1 divert when no answer 2 do not divert 6 Set the call divert switch from GSM to FXO Command 76 n Description Set the call divert switch from GSM to FXO O no from FXO 1 from FXO 24 31 FT5X User Guide 7 Set the call divert number from GSM to FXO Command 77 number Description Set the call diverts number from GSM to FXO When the function of call diversion from GSM to FXO is on GSM dial this Number from FXO port 4 4 4 Detect the caller ID identification function standard 4 4 5 4 4 6 Detect the standard of supporting caller ID identification Command 99 Description Detect the standard of supporting caller ID identification After completing this command the user should hang up the phone immediately If the standard of displaying caller ID identification is complied with local standard then the user s CLI display will show 0123456789 If the device can not display this
15. indicators turn off immediately 6 31 FT5X User Guide 3 Applications 3 1 Voice mode application The Voice Mode Connecting regular telephones to Phone port PSTN port connects with the entry line Under normal circumstances the users make a telephone call incoming or outgoing through the GSM network When Power down the device Automatically switch to PSTN network emergency calls can still achieve the incoming or outgoing Application solution is proposed as following ea C an Voice A E A n Voice Phone FWT Voice mode application 3 2 Voice FAX mode application FT5X connects regular telephone FAX Modem via phone and fax ports The PSTN port connects with entry line The Ethernet port connects with Ethernet that make the device become one wireless modem In normal situation user can call in and call out while telephone routes GSM network When power is off the device switches to PSTN network automatically to realize emergency calling in and out Application solution is proposed as following Voice li a Fax kA Phone a P GSM Data Call ny yn wa FWT SMS Fax Modem Voice FAX mode application 3 3 Pos connection application FT5X supports traditional POS connection depend on the networks When connecting to the FT5X RJ1i1 ports the traditional POS can be used as usual FT5X supports GSM CSD Circuit 7 31 FT5X User Guide Switched data uplink According to this comm
16. ing mode synchronous mode and asynchronous mode the user can order their own by keyboard configuration 4 2 2 Receiving a fax User can receive a fax by attaching a regular G3 Analogue fax machine to the Fax port on the back panel of the FT5X unit The device supports two fax receiving mode synchronous mode and asynchronous mode the user can order their own by keyboard configuration 11 31 FT5X User Guide A Caution FT5X does NOT support switch among GSM voice Fax This function requires GSM network supporting TS61 allowing user to use voice and fax functions in one call As a result when sending a fax please press START key immediately after you complete dialing numbers When receiving faxes please set fax machine to auto receiving fax mode 4 3 Data Function 4 3 1 POS function When the traditional POS connected to the FT5X through the RJ11 ports phone port and fax port you should make sure the number the traditional POS dialed out is data number 1 the number dialed out is data number use the traditional POS as usual 2 when you are not sure the dialing number through the traditional POS whether it is the data number Just add the prefix 02 before the dialed number to ensure the call is data call 4 3 2 Modem function The FT5X has two work modes Common Mode and Modem Mode These two modes cannot exist simultaneity Common Mode The wireless access terminal can provide all the function except the GPRS
17. limited to user self demounting or assembling refit repair dropping and operation not as per user guide etc is not liable to the warranty service The product warranty card is not valid without completely filling out and distributor s stamping Do not damage or modify the production date label Or we are not responsible for relevant service Our company has the final authority for explanation of the product service terms 30 31 FT5X User Guide Warranty Card User is required to fill out the form carefully and keep it in a safe place for future repair claim Customer Tel Name Product Device Type No Purchase __ Y __ M __ D 31 31
18. nufacturer Models Standard Modem Types ESF Standard 19200 bps Modem Nokia ES Standard 28800 bps Modem Standard 33600 bps Modem Ef Standard 56000 bps Modem EF This driver is digitally signed Tell me why driver signing is important Ensure that Standard Modem Types is selected on the left and click on Standard 33600 bps Modem on the right Click Next 15 31 FT5X User Guide Add Hardware Wizard Install New Modem E Select the port s you want to install the modem on S You have selected the following modem Standard 19200 bps Modem On which ports do you want to install it All ports Selected ports Select the serial port that the FT5X is attached to and click Next Add Hardware Wizard Install New Modem Modem installation is finished S Your modem has been set up successfully If you want to change these settings double click the Phone and Modem Options icon in Control Panel click the Modems tab select this modem and then click Properties Cancel Click Finish 16 31 FT5X User Guide Phone and Modem Options Dialing Rules Modems Advanced B gt The following modems are installed Modem Attached To 8 Standard 19200 bps Modem COMI C Click OK The FT5X is now installed as a modem on your PC If you wish to use GPRS refer to section 4 3 2 4 for instructions on setting up for GPRS 17 31 FT5X User Guide 4 3 2 2 Conne
19. ocket connects with the internal interface EXT ports or any extension The PBX extension can call the extension number of access terminal and then realize the voice call in and call out through the access terminal that access the GSM GPRS Application plan B is show as follows D AT F Ei a PBX extension access mode application 9 31 FT5X User Guide 4 Operating Instruction 4 1 Telephone Function 4 1 1 Making a phone call 1 Off hook Pick up the handset you will hear a dialing tone 2 Dial Dial the phone number the system will send out your dialed number automatically 3 Conversation When recipient picks up handset at the other end voice communication is established 4 Clear Clear after hanging up 4 1 2 Receiving a phone call When phone bell is ringing Inuse indicator is blinking Green the user can pick up handset and start talking 4 1 3 Call Waiting and Three Parties Conference Function This device support GSM Call Waiting and three parties conference function Note require starting this service on SIM card The use guide as follows During the call if there is the third party incoming in the wireless access terminals in the external phone handset will hear du du of the Voice ifthe speaker wants to ignore this incoming call do not do any operation If the speaker wants to reject this incoming call press R button and then press 0 If the speaker want to end the current conve
20. rk during thunderstorm or it might cause remote electric shock Please avoid using this product directly under sunshine too long Battery operation Do not throw battery into water or fire Battery would be ineffective when thrown into water and possible explosion might be caused when thrown into fire Do not jointing anything onto battery Jointing might damage battery to cause security malfunction Please dispose the useless battery in accordance with local rules and laws 3 31 FT5X User Guide www microdata fi support microdata fi 2 INSTALLATION INSTRUCTION 2 1 Interface Description pe12v Oona ON OFF a PHONE FAX PSTN Y FT5X Back plane FT5X Back plane interface description Y snes Antenna port DC 12V Power supply ON OFF Power switch IOIO RS232 Serial Port PHONE Phone port connect to the regular phone FAX FAX port connect to the regular fax machine PSTN External line port connect to the external phone line Caution Do NOT plug external line into Telephone socket or it may cause device damage 2 2 Indicators Power Network Inuse Status Indicators There are 4 indicators on the front panel of fixed wireless terminal functioning as follows Slow flash defines Flash once per second to indicate Quick flash defines Flash 10 times per second to indicate Dark defines
21. rsation and start the new conversation press R button and then press 1 or hang up the phone to end current conversation the phone will be ringing and pick up the phone for new incoming call if the speaker wants to hold the current conversation and accept the new call in press R button and then press 2 The speaker can also switch the talk objects by press 2 Inthe process of conference the user can press the button R and then to hold the current call Dial the new number after hearing the dial tone When the speaker talks with the new call the former conversation will still be held If the speaker wants to hold the three parties conference press button R and then 3 to add the current conversation into the holding conversation This realizes the teleconference During the teleconference the speaker can press button R and then hold the current call And dial the new number after hearing the dial tone Hang up the wireless access terminal to end the conference Caution Pressing the hook has the simulative effect in case some telephones have no button R 10 31 FT5X User Guide 4 1 4 Call Divert Function Call divert means that the system diverts the calls from PSTN and GSM The device needs to have a telephone line connected to the PSTN port in order to enable the call divert function There are two modes of the call divert A Diverted from PSTN to GSM Set by keypad command supporting two modes of the call di
22. tion Connect using a modem and a regular phone line or an Integrated Services Digital Network ISDN phone line Virtual Private Network connection Connect to the network using a virtual private network VPN connection over the Internet Click Dial up connection and click Next Click Next New Connection Wizard Connection Name Specify a name for this connection to your workplace Type a name for this connection in the following box Company Name Cellroute For example you could type the name of your workplace or the name of a server you will connect to Enter a name for the connection and click Next Enter the phone number for your internet provider and click Next Click Finish 19 31 FT5X User Guide Connect CellRoute User name Password C Save this user name and password for the following users Anyone who uses this computer 0845 xxx xxx v Enter the Username and Password given to you by your Internet provider and click Dial The computer will then connect to your Internet provider and log you on 4 3 2 3 Disconnecting from the Internet When on line there is a computer icon in the bottom right corner of the screen that flashes whenever data is being transferred A EN 13 45 To terminate the connection right click on this icon and click on Disconnect The FT5X will then go off line and return to voice mode after a few seconds 20 31 FT5X
23. umber is the hotline call number Set the hotline dialing time Command 66 seconds Description Set the time from picking up to auto sending the hotline number by the device Seconds 0 10 is the time that defined by user It indicates that the user do not dial the number after picking up the device will dial the hotline number after Seconds automatically If Second is 0 that indicate the hotline dialing function has been off Emergency call number Set the emergency call number Command 67 n Description set the emergency call number the number could be sent out without SIM card No more than 12 numbers Set the function of number 112 Command 672 n Description n 1 the all emergency call numbers have been set will be instead by 112 n 0 do not instead by 112 Delete the emergency call number Command 670 4 Description delete all the emergency call number that have been set 26 31 FT5X User Guide 4 4 9 GSM network configuration The following command code is in the keyboard commands 10 e cn code i Activate sd Register and activate Statuscheck sd Unable O Unregistered and unable DN Dialing number Pw Password x eK riz HF PW GSM divert always Command 21 DN BS Description GSM divert always GSM divert on busy Command 67 DN BS Description GSM divert on busy GSM divert on No Reply
24. under the Common Mode Modem Mode The data service provided through the serial port of the wireless Voice Data Fax access terminal by using peripheral equipments in order to provide the GPRS application Establishing the Modem Mode 1 When the auto switch mode configured by the user refer to the below the keyboard setup command the PC serial port needs to be connected to the IOIO port in the wireless access terminal Open the serial port in PC and then the device will be auto switched to the Modem mode 2 Under the Modem Mode the user can control the GSM GPRS mode through the serial port directly And user can apply the software in PC to realize the GPRS DATA FAX SMS function on the GSM 3 Using the device under the Modem Mode a Under the auto switch mode Set 83 1 when there is the incoming call on the GSM the user can configure the mode as Switch the mode while ringing or Switch after picking up the phone b Under the restricted Modem mode Set 83 2 the device wont be switched to the Common Mode when calls income Note Above keyboard configuration commands are setup with the common phone Please refer to 4 4 keyboard configuration command for the detailed configuration 12 31 FT5X User Guide To set up your PC to connect to the FT5X unit via the serial port follow the following instructions 13 31 FT5X User Guide 4 3 2 1 Installing the Modem From the Start Menu
25. unication plan people do not need any change when using the traditional POS and allocate numbers remain the same Application plane is show as bellow gag RJ11 port O Traditional POS Pos connection application 3 4 PBX relay mode application the phone port connects with PBX exterior interface TRUNK port the exterior line port connects with the entry line Under normal situation the PBX extension may realize call in or out with the help of access terminal via GSM network When power is off device automatically switches to PSTN network in order to maintain emergency calling in or out Application plane is show as bellow Ay Voice li o a A Fax GSM Data Call Trunk FWT PBX relay mode application 3 5 PBX extension access mode application This mode differ from the classic PBX rely access this mode make the device connect with any extension to realize the PBX extension call in or call out via GSM network This mode will make the PBX access more flexible and convenient Moreover this device can be installed at anyplace where the extension can be installed and easy to install without entering the PBX control room If the user wishes to extend the fully loaded PBX relay lines or manage the fixed relay line and 8 31 FT5X User Guide wireless relay line separately this mode is a best choice The device s external line socket connects with PBX internal interface EXT ports The external line s
26. vert i Call forwarding when No Reply When there is a PSTN call in the phone begins to ring Set the ring frequency by keyboard command If user does not pick up the phone the system will call the appointed number through GSM and connect PSTN with the voice channel of GSM When the call is put through the PSTN caller and GSM receiver can talk with each other il Unconditional Divert Call the appointed number through the GSM when there is a PSTN call in B Call diversion from GSM to PSTN Set by keypad command supports only one divert mode i Unconditional Divert When there is a GSM call in the device will call the appointed number through the PSTN line Set the number by keypad command NOTE Refer to Section 4 4 3 For the Call Divert Commands A Caution 1 The call diversion function can decrease the call charge when the user is out of the office 2 After launching the call diversion the phone port maybe cannot receive the call If there is no response in terminal when pick up the phone and no prompt tone in the handset it indic ate that the system is in the condition of processing the call diversion The user should can cel this function in time when user does not need this function in order to ensure the com mon using 4 2 Fax function 4 2 1 Sending a fax User can send a fax by attaching a regular G3 Analogue fax machine to the Fax port on the back panel of the FT5X unit The device supports two fax send
Download Pdf Manuals
Related Search