TIMERGPS+ USER MANUAL, ENGLISH EDITION SEPTEMBER, 2014
Contents
1. 4 1 3 Summary of basic exercise When the basic exercise has been stopped the exercise summary will be shown on display Use the UP and DOWN buttons to browse through the exercise data The exercise data of each interval will be shown on separate screens Press the INT BACK button to return to exercise standby mode 4 2 Track exercise Select the track exercise from the main menu and press START STOP to confirm The product will then begin searching for a satellite connection and once the connection has been established track exercise standby mode will begin 4 2 1 Track exercise standby mode In the standby mode of the track exercise it is possible to review the previous time and pace results to set the unit of 11 measurement for pace refer to section 8 4 2 Measuring is not yet enabled however and exercise data will not be saved in the exercise log If one is moving with the product when in standby mode the pace when the first lap was started will be shown on display 4 2 2 Starting and ending in track exercise mode Press the START STOP button in the track exercise standby mode to start the exercise The point where one is stood at the time of pressing the START STOP button is the start of the track exercise The width of the track is 30m from the leftmost to the rightmost of the marked start point Every time the start point is passed the product will automatically display the lap data time distance average and maximum pace for2. y CODtFASC e ert NI M M Localization Language iioii etiani tre EDEN De ERE QURE GER UO IEEE EE CU EORR WEE ON Units of measurement wists E Ate e a e ore tee Ph PR Se d Eia 24 Time zone 25 Exercise options Units Interval length Exercise saving 26 Alarm limits 26 Exercise Autostart function Charging the 27 Maintenance 27 Resetting the product in case of problems 28 About the GPS system iiic E ERES ROERR ESSEN 28 12 13 13 1 13 2 13 3 13 4 13 5 14 14 1 14 1 1 14 1 2 14 2 14 3 14 4 14 5 14 6 14 7 14 8 14 9 14 10 14 11 Technical description of main components eese enne 29 Terms and limitations for the use of the product sese 29 Terms for end use agreemeht ssccisicssciscsssaxesesesevsscssavarcstascascsctavansossscacsveavenssssacascsversavesesecazasye 29 Warnings and important safety instructions Declaration of conformity Compliance 32 International limited warranty seen nne ennt enne 33 Terms for end user license agreement eese enne ennt enne 35 Grant of license License annA a centia en THO E HIDE DER ERES Single seh tette eere eee A eee dere a eedem ede eee 36 Restrictions 36 Copyright
3. 1 4 4 2 4 4 3 4 4 4 4 4 5 4 4 6 45 1 452 453 5 1 7 1 7 3 7 4 7 5 Summary of competition function sesssseseeseeeeeeeeeeeenne nee 14 Pausing and continuing the competition function Pause 14 Countdown Setting an optimum time for the countdown function Setting a minute alarm time for countdown function Standby mode of the countdown function Starting and ending the countdown function Summary Of co nt TUNCHON re o ehe ee E eir reu Pausing and continuing the countdown function Pause mode anin rnia ER e HC TET ERR POTE ECHO EE senders Standby mode Of race exercise uae eere ie needed eee dee ede Starting and ending race exercise Summary of race exercise Connecting to the HR Check Using the HR Check without he TimerGPS esee StOD Watch sd oec e RO OR INEO EGG GREECE NT ER GRE LS Exercise log Browse the eetee rote oe eedee ere ee odere Selecta lorse suere tir EA Add a horse Change a horse s name Remove horse 8 5 5 10 10 1 11 Eos THanagement s doeet DG PRECOR NR Se eR ERES YAN ER e Space Remove an exercise S Empty the lot 4 eco e ee ERR ER DEG RH E E Kup M Backlight gt Displ
4. 2 Buttons and operation principles of the user interface 2 1 Power button ON OFF Press and hold the power ON OFF button to turn the product on To turn the product off press and hold the power button for two 2 seconds 2 2 START STOP button Press the START STOP button to start and stop an exercise The START STOP button will also function as the confirmation button press it to select the highlighted menu item In the countdown function using the START STOP button will exit pause mode 23 INT BACK button Press the INT BACK button to return to the previous menu In the basic exercise mode pressing the INT BACK button once will start an interval training session and pressing it a second time will end the training session Pressing it a third time will save the interval after which the product will resume basic exercises The start and end of an interval exercise are signalled by two short sounds accompanied with vibration During the countdown exercise pressing the INT BACK button will enter pause mode and pressing it again will exit pause mode 2 4 UP button Press the up button from the basic mode to enter the menu where the training functions are listed along with the product settings Use the UP button to scroll upwards in the menu or when naming a horse use the UP button to scroll backwards one 8 character when giving a name to horse During basic and race exercises pressing the up button will display the overall time
5. Setting a minute alarm time for the competition function After setting the optimum time the minute alarm time can be set Set the minute alarm time 0 10 minutes using the UP and DOWN buttons If zero 0 is set as the minute alarm time the alarm will not be used during the exercise Pressing the INT BACK button will cancel all choices and return to the previous menu Once the alarm time has been set press the START STOP button to begin establishing satellite connection Searching GPS satellites will be shown on the display After a connection has been established the product will go to the standby mode of the competition exercise 4 3 3 Competitive function standby mode In the competitive function standby mode the time and optimum time are displayed 4 3 4 Starting and ending the competition function Press the START STOP button in the competitive function standby mode to start the competitive function The countdown clock will start counting downwards from the set time As the clock approaches zero 0 the product will begin to make a beep sound after which it will begin to count upwards If the minute alarm time is set the product will alarm in intervals of the selected 13 minutes by beeping and vibrating End the competition function by pressing the START STOP button Exercise saved will be shown on the display and the product will price to competition exercise summary data 4 3 5 Summary of competition function On the f
6. for any purpose requiring precise measuring of pace speed time or distance TIMERGPS Europe Ltd makes no warranty as to the accuracy or completeness of measurement data of the product THE WARRANTIES AND REMEDIES CONTAINED HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES EXPRESS IMPIES OR STATUTORY INCLUDING LIABILITY ARISING UNDER ANY WARRANTY MERCHANT ABILITY OR FITNESS FOR A PARTICULAR PURPOSE STATUTORY OR OTHERWISE THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS WHICH MAY VARY FROM STATE TO STATE IN NO EVENT SHALL TIMERGPS Europe Ltd BE LIABLE FOR ANY INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGE INCLUDING WITHOUT LIMITATION DAMAGES FOR ANY PART OR CITATIONS WHETHER RESULTING FROM THE USE MISUSE OR INABILITY TO USE THE PRODUCT OR FROM DEFECTS IN THE PRODUCT SOME STATES DO NOT ALLOW THE EXCLUSION OF INCIDENTAL OR CONSEQUENTIAL DAMAGE SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU TIMERGPS Europe Ltd retains the exclusive right to repair or replace with a new or newly overhauled replacement product the product or software firmware or offer a full refund of the purchase price at its sole discretion SUCH REMEDY SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY To obtain warranty service contact your local TIMERGPS Europe Ltd authorized dealer or call TIMERGPS Europe Ltd 34 Product Service Centre for shipping instructions Securely pack the product and a copy of the original sales receipt which is
7. may cause undesired operation The product has been tested and found to comply with the limits for a Class B digital product pursuant to part 15 of the FCC rules These limits are designed to provide responsible protection against harmful interference in a residential installation The product generates uses and can radiate frequency energy and may cause harmful interference to radio communications if not installed and used in according with the instructions however there is no guarantee that interference will not occur in a particular installation If the product does cause harmful interference to radio or television reception which can be determined by turning the product off and on the use is encouraged to try to correct the interference by one of the following measures 32 Reorient or relocate the receiving antenna Increase the separation between the product and the receiver Connect the product into and outlet that s on a difference circuit from the receiver Consult the dealer or an experience radio television technician for help The product does not contain any user serviceable parts Repairs should only be made by an authorized TIMERGPS Ltd Product Service Centre Unauthorized repairs on modifications could result in permanent damage to the product and void your warranty and your authority to operate the product under part 15 regulations TimerGPS Europe Ltd does NOT give any authorization for the end customer or retailer to repl
8. part of the product If the product battery is damaged keep it away from children 30 Do not use the neck band or hands free if there is any possibility that you would put yourself your horse or any person or animal in any danger or an unsafe situation Contact your local waste disposal department to dispose of the product battery in accordance with any applicable local laws and regulations The product is inter to be used only as a training aid for horse trainers and must not be used for any other purpose requiring precise measuring of pace speed tempo time or distance Always use your best judgment and exercise common sense when using the product Always carefully compare information displayed on the product to all available measurement sources Do not follow the information displayed on the product if it suggest an uncertain value or would put you or your horse or any other person or animal in an unsafe situation If you see or feel the the product is broken and not working properly do not use the product Follow the instructions on how to repair or ask further instruction from TimerGPS Europe Ltd Product Service Do not use the product for horse training purpose if the outside temperature is too high or too low or there is any possibility that you would put yourself or your horse in an unsafe situation Make sure you know your own and your horse s health condition well before you start using the product as a training aid If you feel any
9. required as the proof for warranty repairs Write the tracking number clearly on the outside of the package Send the product freight charges prepaid to any TIMERGPS Europe Ltd warranty service station Contacting TIMERGPS Europe Ltd main Product Service TIMERGPS Europe Ltd Product Service Temmeksentie 3 Ovi 961 90400 Oulu Finland 14 Terms for end user license agreement 14 1 Grant of license 14 1 1 License By using the product defined in this user manual you are binding yourself hereinafter you to the terms and conditions of this end user license hereinafter EULA including the warranty disclaimers and limitations of liability provisions below If you do not agree to the terms and conditions of this EULA do not use this product YOU AGREE THAT YOU HAVE READ THIS AGREEMENT UNDERSTAND AND AGREE TO BE BOUND BY ITS TERMS AND CONDITIONS OF THIS EULA 35 14 1 2 Single product The firmware embedded integrated and or pre installed in the product and its hardware hereinafter firmware is licensed not sold to a single product by the seller or reseller who sold the product to you hereinafter reseller The firmware may only be used with that single product 14 2 Restrictions You shall not 1 copy modify amend adapt translate reverse engineer decompile disassemble except to the extent that this restriction is expressly prohibited or limited by the applicable law the firmware nor create or attempt to create deriv
10. TIMERGPS TIMERGPS USER MANUAL ENGLISH EDITION SEPTEMBER 2014 Table of Content 1 2 42 1 422 423 43 1 4 32 4 3 3 4 3 4 TimerGPS Product User 5 nennen nennen enne nnne 7 Content of the package Buttons and operation principles of the user interface sssssseeeenenen 8 Power button ON OFF 8 START STOP button 8 INT BACK button UP button DOWN button Startup and initialisation of the TimerGPS sss rennen 9 Exercise functions 1 crucMPIDECME Basic exercise standby ier eet ee n eet t n eerie 10 Starting and ending in basic exercise mode Summary of basic exercise Track exercise 11 Track exercise standby mode rere peer tere 11 Starting and ending in track exercise mode 2 12 Summary of track exercise Competition functiofi areae e preteen e deb e dees sae dees de esee Setting a countdown optimum time for the competition function sss 13 Setting a minute alarm time for the competition function 13 Competitive function standby mode 13 Starting and ending the competition function sese 13 4 3 5 4 3 6 4 4
11. ace the battery or open the device If the end customer or retailer along with anyone else outside TimerGPS Europe s official service points opens the device the warranty is automatically void 13 5 International limited warranty The product is warranted to be free from defects in materials or workmanship for one 1 years from the date of purchase Within this period TIMERGPS Europe Ltd will at its sole option repair or replace any components that fail in normal use Such repairs or replacement will be made at no charge to the customer for parts of labour provided that the customer shall be responsible for any transportation cost This warranty does not apply to 1 cosmetic damage such as scratches nicks or dents 2 consumable parts such as chargers unless product damage has occurred due to a defect in the materials or workmanship 3 damage caused by accident abuse misuse water flood fire or other act of nature or external causes 4 damage caused by service performed by anyone who is not an authorized service provider of TIMERGPS Europe Ltd or 5 damage to a product that has been modified or altered without the written permission of TIMERGPS Europe Ltd In addition TIMERGPS Europe Ltd reserves the 33 right to refuse warranty claims against products or services that are obtained and or used in contravention of the laws of any country The product is intended to be used only as a training aid for horse trainers and must not be used
12. and other rights Limitation of warranty Yo rtremedies e onion PH OPER REB DERE EUER EO TORRE I DEDERE Oed N other watranties c co sede eee oae OX on DEO LENA aoe aaa Disclaimer of liability Sri iie Sith ALM P OE WOMAN AON oye m Beneficiary Export Buttons of the device 2 START STOP button 1 INT BACK button 3 3 UP button E 4 DOWN button E 5 ON OFF power button uen M 6 USB charging and data transfer port Disclaimer The information in this document is subject to change without notice and covers the product defined in the cover sheet hereinafter referred to as simply the product This document is compiled and kept up to date as conscientiously as possible TIMERGPS Europe Ltd cannot however guarantee that the data is free of all errors meticulous or complete and therefore assumes no liability for loss or damage of any kind incurred directly or indirectly through the use of this document Products are not authorised for use in life support or safety critical conditions Use in such conditions or applications is done so at the sole discretion of the customer TIMERGPS Europe Ltd will not warrant the use of its products in such conditions or applications 1 TimerGPS Product User Instructions 11 Content of the package TimerGPS with built in battery Regional charger adapter with USB cable Neck band e Hands free wrist mount Protective silicone cover TimerGPS User manual
13. arm time 0 59 minutes using the UP and DOWN buttons If zero 0 is set as the minute alarm time the alarm will not be used during the exercise Pressing the INT BACK button will cancel all choices and return to the previous menu Once the alarm time has been set press the START STOP button to begin establishing satellite connection Searching GPS satellites will be shown on the display After a connection has been established the product will return to the standby mode of the countdown exercise 4 4 3 Standby mode of the countdown function In the standby mode of the countdown function the time and pace information is displayed to set the unit of measurement for pace see section 8 4 2 If the product is moving in standby mode the pace will be displayed but the exercise data will not be saved in the exercise log 4 4 4 Starting and ending the countdown function While in the standby mode of the countdown function press the START STOP button to start the countdown and begin measuring pace On the top of the display the countdown clock will begin to count downwards from the set time As the clock approaches the optimum time the product will make a beep sound after which it will begin to count upwards If the minute alarm time is set the product will alarm in intervals of the selected minutes by beeping Press the UP button to change 15 the field on the top part of the display to show either the countdown time time or average
14. ative works based on the firmware ii rent lease loan or otherwise transfer rights to the firmware iii publicly distribute the firmware e g by distributing the firmware on a web server for public access You shall keep the contents of the firmware confidential from unauthorized disclosure or use 14 3 Copyright and other rights title and copyrights as well as trade secret patent and other intellectual property and proprietary rights in and to the firmware including but not limited to any images photographs animations video audio music test and applets incorporated into the firmware the accompanying printed materials and any copies of the firmware are owned by the TimerGPS Europe Ltd or its licensors The firmware is protected by copyright laws and international treaty provisions You shall not copy the printed materials accompanying the firmware 14 4 Limitation of warranty The reseller does not warrant that the operation of the firmware or the media on which it is contained will be uninterrupted or 36 error free The reseller furthermore states that not all errors in the firmware or its media can be corrected or need correction nor does the reseller warrant that all defects in the firmware or its media will be corrected The reseller has no control over the conditions under which you use the firmware or media and do not and cannot warrant the results obtained by such use Similarly the reseller does not warrant that th
15. bad symptoms consult your medical doctor or in your horse s case consult a veterinarian before starting to exercise Always use your best judgment and operate the horse in a safe manner Do not become distracted by the product while driving and always be fully aware of all driving conditions Minimize the amount of time spent viewing the product s display while driving Do not change exercise settings or access any functions while driving Pull over in a safe and legal manner before attempting such operations IT IS THE USER S RESPONSIBILITY TO USE THE PRODUCT IN COMPLIANCE WITH ALL APPLICABLE LAWS AND ORDINANCES 31 DONOT USE OR HANDLE THE PRODUCT WHITE OPERATING MOTOR VEHICLES ALWAYS MOUNT YOUR PRODUCT IN A LOCATION THAT DOES NOT OBSTRUCT THE HORSE DRIVER S VIEW OF THE ROAD TIMERGPS EUROPE LTD DOES NOT ASSUME ANY RESPONSIBILITY FOR ANY FINES PENALTIES DAMAGES OR INJURIES THAT MAY BE INCURRED AS A RESULT OF ANY STATE OR LOCAL LAW OR ORDINANCE RELATING TO THE USE OF YOUR PRODUCT 13 3 Declaration of conformity Hereby TimerGPS Europe Ltd declares that the product is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC 13 4 FCC Compliance The product complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 the product may not cause harmful interference and 2 the product must accept any interference received including interference that
16. e functions contained in the firmware will meet your personal requirements or that the firmware or its media will operate in combination with other software or hardware selected by you for use by you TO THE EXTENT PERMITTED BY APPLICABLE LAW YOU ACKNOWLEDGE THAT THE FIRMWARE IS PROVIDED AS IS WITHOUT WARRANTIES OF ANY KIND EXPRESS OR IMPLIED The reseller is not responsible for problems which occur as a result of the use of firmware in conjunction with any software supped by you or with a computer which is incompatible with the operation system for which the firmware is being procured by you 14 5 Your remedies The reseller s entire liability and your exclusive remedy for breach of the foregoing warranty shall be at the resellers option either 1 refund of the price paid for the product ii replacement of the product that does not meet this warranty and which is returned to the reseller This warranty is void if failure had occurred from accident abuse negligence or misapplication 14 6 No other warranties ALL WARRANTIES NOT EXPRESSLY STATED HEREIN ARE DISCLAIMED TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW AND THE RESELLER DISCLAIMS ALL OTHER WARRANTIES EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE WITH REGARD TOE THE FIRMWARE AND THE ACCOMPANYING WRITTEN MATERIALS 37 14 7 Disclaimer of liability The reseller will not be liable for injurie
17. efore the exercise is started Use UP and DOWN keys to select Minutes or Seconds and use START STOP key to select it Using UP and DOWN keys you can adjust minutes and seconds to whatever you desire and once finished use START STOP key again to confirm your selection When ready select Ready and press START STOP key to start exercise You can toggle Autostart function on and off from the Exercise options Go to Settings gt Exercise options gt Exercise autostart Autostart function is enabled when you can see symbol in front of the Autostart word Select the Autostart word and press START STOP button to toggle feature on and off 9 Charging the battery To recharge the product use the charger adapter and USB cable included in the product package Remove the adapter from the plastic packaging and cast the packaging aside Take the USB cable and plug the USB head into the corresponding slot on the adapter Carefully open the protection cap on the bottom of the product and turn out Next plug the other end of the USB cable into the now revealed slot on the product Plug the plug into a power outlet The product should now show an escalating bar next to the BAT icon on the bottom left of the display showing its charging status When the battery is fully charged the bars in the BAT icon will remain solid PLEASE NOTE Do not charge the product below 10 C 50 F or over 30 C 86 F 10 Maintenance When not using the product store it in a d
18. ers are intended third party beneficiaries of the agreement and shall have the right to enforce 38 the terms of the agreement directly against you 1411 Export You agree to comply with all applicable export and re export restrictions Copyrights 2010 2014 TIMERGPS Europe Ltd Contact your local waste disposal department to dispose of the product battery in accordance with applicable local laws and regulations The product complies with EU directives This document is made of recyclable materials T Contact your local waste disposal department to dispose of the product battery in accordance with applicable local laws and regulations The product is CE compliant The product complies with part 15 of FCC Rules e This document is made of recyclable materials 39 TIMERGPS
19. four 4 seconds Press the UP button to show either lap time average pace or overall time on the top part of the display Press the DOWN to toggle between the distance or average pace on the bottom part of the display Press the START STOP button to stop the track exercise Exercise saved text will appear and the product automatically proceeds to the exercise summary data 4 2 3 Summary of track exercise On the first track exercise summary screen the summary data of the whole track exercise is shown Pressing the UP and DOWN buttons will check each individual lap data Press the INT BACK button to return to the track exercise standby mode 4 3 Competition function Select competition exercise from the main menu and press START STOP to begin Then the countdown optimum time will need to be set along with the minute alarm time The product will then begin searching for a satellite connection and once the connection has been established competition exercise standby mode will begin 12 4 3 1 Setting a countdown optimum time for the competition function Set the optimum time in minutes using the UP and DOWN buttons Once you have set the desired minutes press the START STOP button to proceed to the setting the time in seconds When both times have been set press the START STOP button again to proceed to the minute alarm menu where the minute alarm time can be set Press the INT BACK button to cancel all and return to the previous menu 4 3 2
20. g on the product maximum 100 by selecting log space left in the log management menu 7 8 Remove an exercise To remove one or several exercises from the product memory select remove exercise from the exercise log menu A list of horses with saved exercises will appear on the display Select a horse and confirm by pressing the START STOP button to show the list of exercises saved for that horse Select one or more exercises to be removed for a horse Exercises selected for removal will be marked with an x Once the exercises for removal have been chosen press the INT BACK button to remove the exercises The product will show a message reading Are you sure you want to remove selected exercises to confirm removal press the START STOP button To cancel removal press the INT BACK button to return to the previous screen 22 7 9 Empty the log To remove all the exercise data for a horse select clear log from the log management menu A list of horse names with saved exercise data will appear on the display Select horses individually by name or select ALL HORSES to remove the exercise data for every horse at once The number following each horses name indicates the number of saved exercises for that horse After you have selected press the START STOP button to be prompted with a message reading Are you sure you want to remove selected exercises Press the START STOP button again to confirm and remove all the exercises for a horse all ho
21. irst competition exercise summary screen the summary data of the total exercise is shown Press the DOWN and UP buttons to check each competition data Press the INT BACK button to return to the competition exercise standby mode 4 3 6 Pausing and continuing the competition function Pause mode During the competition function press the INT BACK once to pause the timer The PAUSE text will appear in the center of the display and on the top part of the display will be a negative countdown timer or a positive countdown timer if the end countdown time has been surpassed Exit the pause mode by pressing the INT BACK or by pressing the START STOP button after which the product will resume the countdown time 4 4 Countdown Select countdown from the main menu and press START STOP to confirm An optimum time and minute alarm time will need to be set 4 4 1 Setting an optimum time for the countdown function Set the optimum time in minutes using the UP and DOWN buttons Once you have set the desired minutes press the START STOP button to proceed to the setting the time in seconds When both times have been set press the START STOP 14 button again to proceed to the minute alarm menu where the minute alarm time be set Press the INT BACK button to cancel all and return to the previous menu 4 4 2 Setting a minute alarm time for countdown function After setting the optimum time the minute alarm time can be set Set the minute al
22. lete When the products has completed establishing connection with a satellite it will enter the standby mode of the basic exercise Alternatively press the START STOP button when in the start mode and the product will start the basic exercise directly 4 1 1 Basic exercise standby mode In the standby mode of the basic exercise it is possible to review the previous time and pace results to set the unit of measurement for pace refer to section 8 4 2 Measuring is not yet enabled however and exercise data will not be saved in the exercise log 10 4 1 2 Starting and ending in basic exercise mode Press the START STOP button once in the basic exercise standby mode to begin the exercise The product will now start measuring the pace distance and time During a basic exercise press the UP button to select either time average pace or overall time on the top part of the display Press the DOWN to toggle between the distance or average pace on the bottom part of the display Press the INT BACK button once to start the interval function and press it again to stop the interval When the interval has been stopped the display will now show the interval summary data Scroll through the data using the UP and DOWN buttons Press the INT BACK button once again to return to the basic exercise It is possible to make up to 23 intervals during one basic exercise session The interval length can be preset in the exercise section Refer to section 2 7 4 2
23. ns of this agreement do not use the product YOU AGREE THAT YOU HAVE READ 29 THIS AGREEMENT UNDERSTAND AND AGREE TO BE BOUND BY THE TERMS AND CONDITIONS OF THIS AGREEMENT 13 2 Warnings and important safety instructions Read before using the product Failure to avoid potential hazardous situations could result in an accident or collision resulting in death or serious injury Use the product only as specified in this use manual This product has no user replaceable components If these guidelines are not followed the product battery may experience a shortened life or may present a risk of damage to the product fire chemical burn electrolyte leak and or injury Do not charge product battery below 10 50 or over 30 86 For charger adapter and USB cable the socket outlet shall be installed near the product and shall be easily accessible Do not use product under 20 C 4 F or over 45 C 113 F Do not leave the product exposed to a heat source or in a high temperature location such as in direct sunlight in and unattended vehicle To prevent damage remove the product from the heat source and store it out of direct sunlight Do not leave the product exposed a water source or in a high moisture condition such as near to a tap or basin Product is not waterproof Do not disassemble any part from the product Do not puncture or incinerate the product battery Do not use any sharp object to clean any
24. orse To establish a connection with the HR Check bring the product close to the HR Check The devices will be paired automatically if the HR Check is receiving a heart rate signal from the HR Check transmitter 5 1 Using the HR Check without he TimerGPS After a connection has been established the TimerGPS will enter the heart rate check standby mode In the standby mode the TimerGPS will be ready to receive heart rate data from the HR Check To save the data press the START STOP button otherwise press the INT BACK button to return to the heart rate check standby mode For full instructions on how to use the HR Check consult the HR Check user manual 6 Stopwatch The stopwatch function can be used to measure lap times Select stopwatch from the main menu and press START STOP to confirm TIME 0 00 0 will be shown in the center of the display and the lap time 0 00 0 will be at the bottom Press the START STOP button to start and stop the stopwatch It is possible to measure lap times during simply by pressing the INT BACK button during the stopwatch and the lap time will be shown at the bottom of the display Restart the stopwatch by 19 pressing the INT BACK button when timing is paused 7 Exercise log In the exercise log it is possible to browse the data saved in the exercise log switch a horse for the next exercise that will be saved add or delete a horse change the name of a horse check the memory capacity of the p
25. pace Press the DOWN button to display the distance overall time and average page at the bottom part of the display Press the START STOP button to stop the countdown exercise Exercise saved will appear on the display and the product will automatically shift to the countdown exercise summary data 4 4 5 Summary of count function On the first countdown exercise summary screen the summary data for the whole exercise is shown Press the UP and DOWN buttons to browse through the data Press the INT BACK button to return to the countdown exercise standby mode 4 4 6 Pausing and continuing the countdown function Pause mode You can pause the countdown function by pressing the INT BACK button once The PAUSE text will appear in the centre of the display and on the top part of the display the current countdown time will be shown or if the time limit has been surpassed a positive countdown time will be displayed Exit the pause mode by pressing either the INT BACK button again or by pressing the START STOP button once after which the product will resume the countdown timer 4 5 Race exercise On the main menu select race exercise and press START STOP to confirm Select a distance from the list e g 1600m 2100m 2600 3100m The product will then begin searching and establishing a satellite connection and will then enter the race exercise standby mode 16 4 5 1 Standby mode of race exercise In the standby mode the time and pace info
26. respond with things such as an official race watch etc Use the UP and DOWN buttons to set the hour and press the START STOP button to confirm the selection Next select the minutes and press the START STOP button to confirm After both times have been selected Settings saved will appear on screen and the product will automatically return to the settings menu 8 5 Exercise options The exercise menu includes Units of measurement Alarm limits Interval length Exercise saving Exercise autostart 8 5 1 Units Select the desired unit of measurement for pace from the units menu There are seven 7 units of measurement to choose from min km m min km h min mi min fur yg min and mph 8 5 2 Interval length In the interval length menu the interval length can be set and can be at different lengths depending on the unit of measurement If the interval distance is set greater than 0 the interval exercise will be automatically saved according to this setting after the 25 distance has been surpassed If the interval length is set at zero 0 it is removed from the interval exercise and the interval exercise will function normally 8 5 3 Exercise saving In the exercise saving menu exercise saving can be enabled or disabled according to whether or not the product saves exercise data in its own memory or in the exercise log If saving is disabled the exercise data will only be shown immediately after the exercise and will not be sa
27. rmation is shown on display to set the unit of measurement for pace see section 8 4 2 Measuring is not active yet and the exercise data will not be saved in the exercise log 4 5 2 Starting and ending race exercise Press the START STOP button in the race exercise standby mode to start the exercise Use the DOWN button during the exercise to change between the distance and average pace information shown at the bottom of the display Use the UP button during the race exercise to change the field on the top of the display to show either overall time time or average pace When the whole distance of the race exercise has elapsed the exercise will stop automatically Time distance average and max pace information from the last 500m will appear on the display Use the UP and DOWN buttons to check the exercise summary of the whole race exercise Press the START STOP button during the race exercise to manually stop the race exercise before the selected distance is completed The average pace information of each completed interval will show on the display 17 4 5 3 Summary of race exercise The first exercise summary screen shows the summary data of the whole exercise Pressing UP and DOWN buttons to check each race data Press the INT BACK button to return to the race exercise standby mode 18 5 Connecting to the HR Check The TimerGPS can connect to the TimerGPS accessory HR Check wirelessly to check the rest and recovery heart rate of the h
28. roduct view and delete saved exercise data or delete all the data in the log browse heart rate data if paired with a HR Check The exercise log is found in the main menu 7 1 Browse the log Saved exercise data can be browsed by selecting browse log and confirming by pressing the START STOP button Select a horse with the UP and DOWN buttons and confirm the choice by pressing START STOP The exercise data for the chosen horse will now be shown and can be browsed through with the UP and DOWN buttons The number following each horses name indicates the number of saved exercises for that horse The exercise data is listed in reverse chronological order Return to the previous menu by pressing the INT BACK button 20 7 2 Select a horse Use the select a horse function to select the horse whose exercises will be saved In the exercise log highlight select a horse and press the START STOP button to confirm The selected horse will be marked with a triangle gt next to its name Select a horse with the UP and DOWN buttons and press START STOP to view a selected horse s exercise data After this the exercise data of the selected horse will be saved in the log Press the INT BACK button to return to the menu 7 3 Add a horse Use the add a horse function to add a new horse into the product s memory Select add horse from the exercise log menu Add name will appear on the display with the letter a Press the UP and Down buttons to scroll thro
29. rses To cancel removal press the INT BACK button to return to the previous menu After the removal is completed the product will automatically return to the clear log menu 8 Settings In the settings menu the settings can be customized The settings menu includes Backlight Display Contrast Sound Language Exercise settings 8 1 Backlight Select Backlight from the settings menu to adjust the brightness of the display Choose from three 3 options bright dim and off 23 8 2 Display contrast From the Display contrast menu you can adjust the contrast of the display If the graphics of the display seems to be too light or dark adjust the counter by using UP and DOWN keys 8 3 Sound In the sound menu sounds can be enabled and disabled 8 4 Localization The ocalization menu includes Language Units of measurement Time zone 8 4 1 Language Select the language in which the products display will read There are six 6 languages to choose from English French Italian Finnish Swedish and German Select a language and press the START STOP button to confirm 8 4 2 Units of measurement Select the desired unit of measurement for pace from the units menu There are seven 7 units of measurement to choose from min km m min km h min mi min fur yd min and mph 24 8 4 3 Time zone By default the product uses the time zone given by the GPS satellites but the time zone can be set manually to cor
30. ry place at room temperature Do not store within wet moist or any kind of non 27 breathable material such as plastic bags or sports bags or any material that conducts electricity e g a wet towel Do not expose it to direct sunlight for extended periods Clean the product with a cloth moistened with a mild soap and water solution Dry the product carefully with a soft towel Never use alcohol cleansing chemicals or abrasive materials such as steel wool Do not use running water or submerge the product in water or other liquids The product is not waterproof only water resistant NOTE Every time before use make sure that the plastic cap for the USB port is well in place Should the product require service contact a TimerGPS Europe Ltd Product Service Centre Check where the nearest service center is by visiting www timergps com Product warranty does not cover direct or indirect damages incurred by service that has not been authorized by TimerGPS Europe Ltd 10 1 Resetting the product in case of problems If for some reason the product does not respond to any button push and will not cease despite pushing and holding the power button down it is possible to reset the product by pressing the INT BACK button and the UP button simultaneously 11 Aboutthe GPS system The global positioning system GPS is operated by the government of the United States of America who are solely responsible for its accuracy and maintenance The system is subjec
31. s or damages to erosions or property resulting from any cause whatsoever with the exception of injuries or damages caused by the gross negligence of the reseller This limitation applies to all firmware In no event will the reseller be liable for any damages resulting from loss of data loss of use loss of revenue or any other pecuniary loss Furthermore the reseller disclaims any and all liability for indirect incidental special consequential or other similar damages even if the reseller has been advised of the possibility of such damages In any case the resellers entire liability under any provision of the terms and conditions shall be limited to the amount actually paid by you for the product less applicable depreciation 14 8 Confidentiality You shall maintain the confidentiality of the firmware and respective documentation 14 9 Termination Without prejudice to any other rights the reseller may terminate these terms with no prior notice if you fail to comply with the terms and conditions as stated heron In such an event you MUST return the product to the reseller These terms and conditions take precedence over any terms and conditions of any other agreement between the reseller and you regarding the firmware The provisions contained in the agreement that protect the interests of the reseller or TimerGPS Europe Ltd in the firmware shall survive the termination of this agreement 14 10 Beneficiary The reseller s licensors and suppli
32. t to changes which could affect the accuracy and performance of all GPS equipment When using the product in a place where the GPS signal cannot reach the product such as a dense forest under and around power lines or directly beside a mobile phone the product may temporarily show incorrect readings They will be automatically corrected when the product is moved to an area where the signal can reach the product Strong electromagnetic signals can also cause the product to display erratic readings Electromagnetic disturbances may occur near high voltage power lines traffic lights overhead lines of electric railways car motors or cellular phones 28 12 Technical description of main components Product dimensions Battery 3 7 V Li ion Li Po Heigh Weight Thickness 98mm 64 mm 18 DC Output 3 1 4 2 V 900 mAh mm Operating time 10 20 hours Product weight 70 Grams Display Transflective display Charger Included in the package GPS u Blox AC Input 100 240 V 100 mA 50 60 Hz Buzzer Build in buzzer DC Output 5 0V 550 mA Measurement accuracy 296 13 Terms and limitations for the use of the product 13 1 Terms for end use agreement By using the product defined in this user manual you are binding yourself hereinafter you to the terms and conditions of the end user agreement including the warranty disclaimers and limitations of liability provisions stated in this user manual If you do not agree to there terms and conditio
33. time or average pace at the top of the screen During a track exercise pressing the UP button will show the overall time lap time or average pace at the top of the display During a countdown exercise pressing the UP button will display the countdown time time or average pace 2 5 DOWN button Press the down button to get from the basic mode to the menu where all the training functions are listed Pressing the down button will select the next item on the menu list or brows a character forwards when naming a horse During a basic exercise track exercise or race exercise pressing the down button will show the distance average pace of time at the bottom the display 3 Startup and initialisation of the TimerGPS Press and hold the power button switch the product on The first time the product is switched on one must select a language with the UP and DOWN buttons and press the START STOP button to confirm language language can be changed later from the settings menu After the language has been selected choose the unit of distance the device will use to display data Select the desired unit with the UP and DOWN buttons and press the START STOP button to confirm The product will now switch itself off and need to be switched on again A prompt to add a horse will be shown on display The default name for the horse will be shown as UNNAMED Delete characters one by one with the INT BACK button then use the UP and DOWN buttons to select each individ
34. ual character for the horse s name Press the START STOP button to confirm a selected character then when the horse s full name has been typed select the lt 1 character from the list and press the START STOP button finally to confirm the horse s name The product will now be in start mode and you can see the version of the program the product is using Press the UP or DOWN button to go to the menu From here it is possible to browse the exercise log select different exercises or change 9 the settings of the product To begin searching for a satellite press the START STOP button in the start mode Searching GPS satellites will appear on the display and the percentage level will increase until the process is complete After the search is complete the basic exercise standby mode will be resumed Note The best way to receive satellite signals is to take the device outside and remain out of the way of any tall obstructions such as tall buildings or trees When the product is powered up for the first time it may take a few minutes to establish connections with a satellite It will be easier to find satellites if the product remains stationary 4 Exercise functions 4 1 Basic exercise Highlight basic exercise from the menu and press the START STOP button to confirm The product will now begin searching for a satellite connection Searching GPS satellites will appear on the display and the percentage level will increase until the process is comp
35. ugh characters and press START STOP to confirm a selection To delete a character press the INT BACK button When naming the horse is complete select the symbol from the list and press the START STOP button 7 4 Change a horse s name Use the rename horse function to edit or rename a horse In the exercise log menu select rename horse from the exercise log menu and press the START STOP button the saved horse s names will appear on the display For instructions on how to name the horse refer to section 7 3 7 5 Remove horse Use the remove horse function to remove a horse from the product s memory Select remove horse from the exercise log menu and press the START STOP button to show a list of all horse names on the display After selecting a horse a message reading Are you sure you want to remove horse will appear on the display Press the START STOP button to permanently remove the 21 horse The product will then return to the remove horse menu If all the horse s names are deleted the product will prompt to name new horse To return to the previous menu press the INT BACK button NOTE Once a horse has been removed all the exercise data saved for that horse will also be deleted permanently 7 6 Log management Select log management from the exercise log and press START STOP to check the memory status of the product and delete saved exercises or empty the log entirely 7 7 Space left Check how much memory is remainin
36. ved in the exercise log and cannot be accessed later If saving is enabled the exercise data will be saved in the exercise log for post analysis By default exercise saving is enabled The selected option will be marked with a triangle gt beside it 8 5 4 Alarm limits In the alarm limits menu alarm limits can be enabled or disabled When alarm limit is enabled the product will make a beep sound when it detects the user is driving slower or faster than the given minimum and maximum pace limits respectively There are four 4 options not enabled only max pace only min pace or both maximum and minimum pace limits enabled Set alarm limits in the alarm minutes menu Select the minimum pace or maximum pace and which will be defined according to which units of measurement have been set Select minimum pace and press the START STOP button Use the UP and DOWN buttons to select the minutes then press the START STOP button again to set the seconds Press START STOP once to more to confirm the minimum pace After the settings saved prompt appears on the screen the product will return to the menu Set the maximum pace in the same way the minimum pace was set 26 8 5 5 Exercise Autostart function When the Autostart function is enabled the driver can set a time of how long TimerGPS waits until the exercise will start automatically If the Autostart feature is enable the timer will ask minutes and seconds for the Autostart function every time b
Download Pdf Manuals
Related Search