TLB Light Source User Manual
Contents
1. Optional color The TLB Light Source has the ability to switch filters one colored filter in or out of the light path The handle for the filter slide is located on the right side of the TLB Light Source It is stainless steel and located between the mirror control knob and the power cord The filter slide can be pulled to the right and has three detents lt has a positive stop to prevent it from being pulled completely out of the base Pulling the filter slide all the way to the right first detent allows a color filter to be installed or removed The color filter has very fine threads and must be GENTLY screwed into the opening on the front side of the filter slide A light touch is required as forcing the threads will result in permanent damage Pushing the filter slide to the left will then engage the second middle detent This is the operating position with the color filter OUT of the light path Or ID Version 0 4 October 3 2013 7 Pushing the filter slide further to the left will then engage the third detent This is the operating position with the color filter IN the light path The foot The foot switch controls the brightness of the LED switch light It is a useful way to change the brightness optional when the operator s hands are occupied with other tasks Increase brightness by pressing on the right pedal Decrease brightness by pressing on the left pedal Momentary taps will change the brightness by one2. TLB Light Source User Manual OLIGO OI Version 0 4 October 3 2013 INDEX Warnings Safety instructions General operation General cleaning guidelines Exterior surfaces of TLB illuminating base Mirror and color filters Foot switch Product specifications TLB Light Source dimensions Replacement parts Or GID Version 0 4 October 3 2013 Oo 0 O OO I BR 10 11 WARNINGS Do not attempt to modify this product in any way without written authorization from ORIGIO and Diagnostic Instruments Inc Unauthorized modification will void the warranty and may cause personal injury The TLB Light Source is designed for the illumination of biological specimens It is the responsibility of the user to qualify that this product meets the requirements for their application In no event and under no circumstances shall the manufacturer be liable to an individual or entity for any indirect special consequential or incidental losses or damages including without limitation lost profits TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS PRODUCT TO RAIN OR EXCESSIVE MOISTURE TO REDUCE THE RISK OF ELECTRICK SHOCK DO NOT REMOVE COVERS OR OPEN POWER SUPPLY NO USER SERVICEABLE PARTS INSIDE REFER TO QUALIFIED PERSONNEL 4 Version 0 4 October 3 2013 Or GID SAFETY INSTRUCTIONS e Read these instructions e Keep these instructions e Heed all warnings e Follow all instructions Do not attempt to use this product in any manner not sp
3. e is called darkfield illumination Darkfield illumination causes small semi transparent specimens to glow against a dark background It is useful for unstained transparent biological specimens The mirror control Knob is located on the right side of the base The mirror control knob consists of two parts the inner silver locking ring and the outer black tilt control knob Turning the silver locking ring clockwise will lock both the tilt and sliding functions Turning it counterclockwise will allow the tilt and sliding functions to be adjusted The black tilt control knob is limited to a 55 range of adjustment It can be adjusted when the silver locking ring is unlocked The mirror can slide front to back when the silver locking ring is unlocked Simply push on the black tilt control knob to slide the mirror assembly from front to back Version 0 4 October 3 2013 Or GID The LED light The LED light has a lifetime of over 50 000 hours and is designed to be a permanent part of the TLB Light Source It is NOT replaceable by the customer If the LED light will not turn on check the fuse located in the power entry module The power entry module is where the power cord plugs in and is located on the right side of the base near the back In the event of a failure of the LED light or the power supply the TLB Light Source must be returned to the factory for service There are no user serviceable parts in the TLB Light Source
4. ecified by the manufacturer as manufacturer will not be held responsible Clean according to the cleaning instructions in the cleaning guidelines section of this guide This product is designed for indoor use only Do not expose to rain or excessive moisture Install in accordance with the manufacturer s instructions Do not install near any heat sources such as radiators heat registers stoves or other apparatus that produce heat Do not defeat the safety purpose of the grounding type plug The TLB Light Source uses a grounding type plug which has two blades and a third grounding prong The third prong is provided for your safety If the provided plug does not fit your outlet consult an electrician for replacement of the obsolete outlet Only use the attachments accessories specified by the manufacturer Unplug this apparatus when it will be unused for long periods of time Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as when the power supply cord or plug is damaged liquid has been spilled or objects have fallen into the apparatus the apparatus has been exposed to rain or excessive moisture does not operate normally or has been dropped Do not allow an impact shock or any objects to fall into the product Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock Do not overload wall outlets Overloaded
5. step Holding a pedal down will continuously change the brightness in steps until the pedal is released or until the brightness limit is reached Note The rocker switch brightness control on the left side of the base remains operational when the foot switch is plugged in The connector for the foot switch cable is located on the rear of the TLB Light Source To disconnect Unplug the main power cord from either the the unit power entry module on the base or from the outlet General cleaning guidelines Exterior surfaces of TLB illuminating base Use a soft cloth dampened with a mild soapy solution to wipe down all exterior surfaces Care should be taken not to spray or drip solution into the rear of the unit through the vented openings 8 Version 0 4 October 3 2013 OI Mirror and color filters Use a cotton swab slightly dampened with 70 isopropyl alcohol and gently wipe in a circular pattern from the center outward Follow with a dry cotton swab Repeat as necessary Use a cotton tipped swab with either a cardboard or plastic shaft NOT a wooden shaft Lens tissue can also be used in place of a cotton swab Allow color filters and mirror to cool before cleaning Foot switch Use a soft cloth dampened with a mild soapy solution to wipe down all exterior surfaces Care should be taken not to spray or drip solution into the foot switch Or GID Version 0 4 October 3 2013 PRODUCT SPECIFICATIONS TLB Ligh
6. t Source is manufactured for ORIGIO by Diagnostic Instruments Weight without filter or power cord 3 27kg 7 20lbs Electrical Requirements Input AC 88 250V 47 63 Hz Max Power 30 Watts Fuse 2 5 A 250V Slow Blow 5 x 20mm Operating Environment 0 C 40 C 32 F 104 F 5 95 relative humidity non condensing LED Lumens 1 020 Im Lifetime 50 000 hours at gt 70 initial brightness the LED does not fail it just slowly gets dimmer Color temperature 4 100 K CRI 80 TLB Light Source dimensions AI P 800806 IIIS UIL GSV nnnnn 10 Version 0 4 October 3 2013 Or GID REPLACEMENT PARTS Description Power supply fuse Foot Switch OrlgIo Catalog number FUSE2 5A TLBFTSWCH Version 0 4 October 3 2013 11 ORIGIO a s Knardrupvej 2 2760 M l v Denmark Tel 45 46 79 02 00 Fax 45 46 79 03 00 Customer serviceQorigio com www origio com 12 Version 0 4 October 3 2013 OrlgIo
7. wall outlets loose or damaged wall outlets extension cords frayed power cords or damaged or cracked wire insulation are dangerous Any of these conditions could result in electric shock or fire Or GID Version 0 4 October 3 2013 5 GENERAL OPERATION To get started To control the LED light To control the mirror Turn the Light Source on by pressing the I top side of the red rocker switch located on the front of the unit Turn the Light Source off by pressing the O bottom side of the red rocker switch Brightness is controlled by a large rocker switch located on the left side of the Light Source toward the front Increase brightness by pressing on the top of the rocker switch Decrease brightness by pressing on the bottom of the rocker switch Momentary taps will change the brightness by one step Holding the switch down will continuously change the brightness in steps until the switch is released or until the brightness limit is reached The TLB Light Source features a mirror that can be tilted through a 55 arc and can slide front to back Different mirror positions change the angle of light that illuminates the specimen Sliding the mirror toward the back and tilting it so that bright light fills the field of view is called brightfield illumination and is useful for large translucent specimens Sliding the mirror toward the front and tilting it so that the light hits the specimen at an angl
Download Pdf Manuals
Related Search