Biostar M7VIZ-SATA Owner's Manual
Contents
1. Item Options Description Date mm dd yy Set the system date Note that the Day automatically changes when you set the date Time hh mm ss Set the system internal clock IDE Primary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Primary Slave Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Slave Options are in its sub Press Enter to enter the menu sub menu of detailed options Drive A 360K 5 25 in Select the type of floppy Drive B 1 2M 525 in disk drive installed in your system 720K 3 5 in 1 44M 3 5 in 2 88M 3 5 in None Video EGA VGA Select the default video CGA 40 device CGA 80 MONO M7VIZ SATA BIOS Setup Item Options Description Halt On All Errors Select the situation in which No Errors you want the BIOS to stop Base Memory All but Keyboard All but Diskette All but Disk Key N A the POST process and notify you Displays the amount of conventional memory detected during boot up Extended Memory N A Displays the amount of extended memory detected during boot up Total Memory N A Displays the total memory available in the system M7VIZ SATA BIOS Setup 3 Advanced BIOS Feat2. Advanced Chipset Features This submenu allows you to configure special chipset features Integrated Peripherals This submenu allows you to configure certain IDE hard drive options and Programmed Input Output features M7VIZ SATA BIOS Setup Power Management Setup This submenu allows you to configure the power management features PnP PCI Configurations This submenu allows you to configure certain Plug and Play and PCI options PC Health Status This submenu allows you to monitor the hardware of your system Frequency Voltage Control This submenu allows you to change CPU clock Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence These configurations are factory settings optimized for this system A confirmation message will be displayed before defaults are set Load Optimized Defaults V N N Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility You will be prompted with to enter a password M7VIZ SATA BIOS Setup Set User Password If the Supervisor Password is not set then the User Password will function in the same way as the Supervisor Password If the Supervisor Password is set and the User Password is set the User will only be able to view configurations but will not be able to
3. BIOS Setup Introduction This manual discussed Award M Setup program built into the ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in battery backed RAM so that it retains the Setup information when the power is turned off The Award BIOS installed in your computer system s ROM Read Only Memory is a custom version of an industry standard BIOS This means that it supports Intel Pentium 4 processor input output system The BIOS provides critical low level support for standard devices such as disk drives and serial and parallel ports Adding important has customized the Award BIOS but nonstandard features such as virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system The rest of this manual is intended to guide you through the process of configuring your system using Setup Plug and Play Support These AWARD BIOS supports the Plug and Play Version 1 0A specification ESCD Extended System Configuration Data write is supported EPA Green PC Support This AWARD BIOS supports Version 1 03 of the EPA Green PC specification APM Support These AWARD BIOS supports Version 1 1 amp 1 2 of the Advanced Power Management APM specification Power management features are implemented via the System Management Interrupt SMI Sleep and Suspend power management modes are supported Power to t
4. DRAM Timing This item determines DRAM clock timing follow SPD or not The Choices Auto By SPD default Manual Turbo Ultra 13 M7VIZ SATA BIOS Setup DRAM CAS Latency When DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The Choices 2 5 default 2 Bank Interleave This item allows you to enable or disable the bank interleave feature The Choices Disabled default 2 bank 4 bank Precharge to Active Trp This items allows you to specify the delay from precharge command to activate command The Choices 2T 3T 4T 5T default Tras Non DDR 400 DDR 400 This item allows you to choose Non DDR 400 DDR 400 The Choices 6T 8T 7T 10T default ST 6T 8T 12T Active to Precharge Tras This items allows you to specify the minimum bank active time The Choices 7T 6T default Active to CMD Tred Use this item to specify the delay from the activation of a bank to the time that a read or write command is accepted The Choices 2T 3T 4T 5T default DRAM Burst Length The Choices 4 default 8 DRAM Queue Depth This item permits to place the depths of the memory The deeper the depth is the better is this function The Choices 4 level default 2 level 3 level DRAM Command Rate This item controls clock cycle that must occur between the last valid write operation and the next command The Choices 1T Command 2T Command default Write R
5. Slave UDMA Ultra DMA 100 functionality can be implemented if it is supported by the IDE hard drives in your system As well your operating environment requires a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both support Ultra DM A 100 select Auto to enable BIOS support The Choices Auto default Disabled IDE HDD Block Mode If your IDE hard drive supports block mode select Enabled for automatic detection of the optimal number of block read writes per sector the drive can support The Choices Enabled default Disabled VIA OnChip PCI Device If you highlight the literal Press Enter next to the OnChip PCI Device label and then press the enter key it will take you a submenu with the following options VIA 3058 AC97 Audio This option allows you to control the onboard AC97 audio The Choices Auto default Disabled VIA 3068 MC97 Modem This option allows you to control the onboard MC97 modem The Choices Auto default Disabled VIA 3043 OnChip LAN This option allows you to control the onboard LAN The Choices Enabled default Disabled Onboard LAN Boot ROM This item allows you to enable or disable Onboard LAN Boot ROM The Choices Disabled default Enabled Onchip USB Controller Select Enabled if your system contains a Universal Serial Bus USB controller and you have USB peripherals The Choices All Enabled default All
6. 2 Seepconrd Bes FS p ene DES put 5 VA feonnector e WA INVA 8 PowerlED 5 9 HDD LED Hard drive Power LED Power LED HDD LED LED Power LED S Ground Reset 14 Power button Power on 15 Resetconro bus Te Ground button v NA 8 Rey 20 Key par r 22 Ground IGonnector RRX Headers for USB Ports at Front Panel JUSB1 JUSB2 This connector allows user to connect additional USB cables at PC front panel and also can be connected with internal USB devices like USB card reader Pin Assignment Pin Assignment Hausewc i 3 UA DT eround 8 Ground GLK c p NO 1 M7VIZ SATA Fre quency Selection JC LK1 Default a cose Open Opm 34 Cose Close Open 56 Opn Opm Open Note The JCLK1 is set at 133 MHz as factor default setting Clear CMOS Header JCMOS1 By placing the jumper on pin2 3 it allows user to restore the BIOS safe setting and the CMOS data please carefully follow the procedures to avoid damaging the motherboard JCMOS1 Assignment Normal Operation Def ault X Clear CMOS Procedures Remove AC power line Set the jumper to Pin 2 3 dose Wait for five seconds Set the jumper to Pin 1 2 dose Power on the AC Reset your desired password or clear the CMOS data OP Clete oa ou M7VIZ SATA CHAPTER 4 USEFUL HELP 4 1 AWARD BIOS BEEP CODE Beep Sound
7. Disabled Onchip EHCI Controller The Choices Enabled default Disabled 18 M7VIZ SATA BIOS Setup USB Keyboard Mouse Support This item allows you to enable or disable the USB Keyboard Mouse Legacy Support The Choices Disabled default Enabled Super IO Device If you highlight the literal Press Enter next to the Super IO Device label and then press the enter key it will take you a submenu with the following options Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you wish to use it If install and FDC or the system has no floppy drive select Disabled in this field The Choices Enabled default Disabled Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports TheChoices Disab led 3 F8 IRQ4 default 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Auto Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports The Choices Disabled 2F8 IRQ3 default 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 Auto UART Mode Select This item allows you to determine which Infra Red IR function of onboard I O chip The Choices Normal default AS KIR IrDA UR2 Duplex Mode Select the value required by the IR device connected to the IR port Full duplex mode permits simultaneous two direction transmission Half duplex mode permits transmission in one direction only at
8. Fail Off gt IRQ Event Activity Detect Press Enter Ti Move Enter Select PU PD Ualue Fi Save ESC Exit Fi General Help 5 Previous Values F Optimized Defaults ACPI function This item displays the status of the Advanced Configuration and Power Management ACPI The Choices Enabled default Disabled ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system The Choices S1 POS default Power on Suspend S3 STR Suspend to RAM S1 S3 POS STR Power Management This category allows you to select the type or degree of power saving and is directly related to the followin g modes 1 HDD Power Down 2 Suspend Mode There are four options of Power Management three of which have fixed mode settings Min Power Saving 21 M7VIZ SATA BIOS Setup Minimum power management Suspend Mode 1 hr HDD Power Down 15 min Max Power Saving Maximum power management only available for sl CPU s Suspend Mode 1 min HDD Power Down 1 min User Define default Allows you to set each mode individually When not disabled each ofthe ranges are from 1 min to 1 hr except for HDD Power Down which ranges from 1 min to 15 mmn and disable HDD Power Down When enabled the hard disk drive will power down and after a set time of system inactivity All other devices remain active The Choices Disabled default 1 Min 2 Min 3 Min 4 Min 5 Min 6 Min
9. Hard disk can be read and applications files can be used but booting from hard disk 2 Ref ormat the hard driv e is impossible Re install applications and data using backup disks creen message says Invalid Rev iew system s equipment Make surg Cannot boat system after installing 1 Set master slave jumpers Second hard driv e correctly Run SETUP program and select correct drive types Call the drive manuf acturers f or compatibility with other drives 16 M7VIZ SATA CHAPTER 5 WARPSPEEDER 5 1 INTRODUCTION WarpSpeeder a new powerful control utility features three user friendly functions including Overclock Manager Overvoltage Manager and Hardware Monitor With the Overdock Manager users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click The Overvoltage Manager on the other hand helps to power up CPU core voltage and Memory voltage The cool Hardware Monitor smarty indicates the temperatures voltage and CPU fan speed as well asthe chipset information Also in the About panel you can get detail descriptions about BIOS model and chipsets In addition the frequency status of CPU memory AGP and PCI along with the CPU speed are synchronically shown on our main panel Moreover to protect users computer systems if the setting is not appropriate when testing and results in system fail or hang WarpSpeeder technology assures the system stability by autom
10. Vertical audio port including 1 line in connector 1 line out connector and 1 MIC in connector LAN Mouse Ce x port 7 gt fs Fa WE gia le E USB 2 U Keyboard ER Line In Surround Line Out Mic In 1 Base Center fu B BIOS amp Software BIOS Award legal BIOS Supports APM1 2 SupportsACPI Supports USB Function Software Supports Warpspeeder 9th Touch FLASHER Offers the highest performance for Windows 98 SE Windows 2000 Windows Me Windows XP SCO UNIX Linux etc i N M7VIZ SATA PACKAGE CHECKLIST FDD Cable X 1 HDD Cable X 1 User s Manual X 1 Fully Setup Driver CD X 1 Rear UO Panel for Micro ATX Case X 1 optional USB 2 0 Cable X1 optional S PDIF out Cable X 1 optional Serial ATA Cable X 1 optional Serial ATA Power Switch Cable X 1 optional M7VIZ SATA 1 3 MOTHERBOARD LAYOUT H IJANF 4 Note ll represents the 1 pin mO 9M ME ge rop m M7VIZ SATA 1 4 MOTHERBOARD COMPONENTS JATXPWER1 ATX power source K connector JNFAN 1 optional north bridge fan JCFAN1 Power header for CPUfan M Power headerfor L Rear side back panel connectors N JF AUDIOt Front panel audio O header JCDIN1 CD ROM audio in P connector AGP1 Accelerated Graphics Pot Q slot JSPDIF 1 optional Digital audio out R connector CNR1 Communication Network S Riser slot PCl1 3 Peripheral Component T Interconnect
11. and then is automatically set to the Disabled mode The above settings will be shown on the screen only if Manual is chosen for the resources controlled by function Legacy is the term which signifies that a resource is assigned to the ISA Bus and provides non PnP ISA add on cards PCI ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add on cards and peripherals The Choices Disabled default Enabled Resources Controlled By By Choosing Auto ESCD default the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral By Choosing Manual the user will need to assign IRQ amp DMA for add on cards Be sure that there are no IRQ DMA and I O port conflicts IRQ Resources This submenu will allow you to assign each system interrupt a type depending on the type of device using the interrupt When you press the Press Enter tag you will be directed to a submenu that will allow you to configure the system interrupts This is only configurable when Resources Controlled By is set to Manual IRQ 3 assigned to PCI Device IRQ 4 assigned to PCI Device IRQ 5 assigned to PCI Device IRQ 7 assigned to PCI Device IRQ 9 assigned to PCI Device IRQ 10 assigned to PCI Device IRQ 11 assigned to PCI Device IRQ 12 assigned to PCI Device IRQ 14 assigned to PCI Device IRQ 15 assigned to PCI Device 26 M7VIZ SATA BIO
12. for PCI slots butitis also equipped with an Accelerated Graphics Port AGP An AGP card will take advantage of AGP technology for improved video efficiency and perfomance especially wth 3D graphics Communication Network Riser Slot CNR1 The CNR specification is an open Industry Standard Architecture and it defines a hardware scalable riser card interface which supports modem only Serial ATA Connector JSATA1 JSATA2 The motherboard has a PCI to SATA Controller with 2 channels SATA interface it satisfies the SATA 1 0 spec and with transfer rate of 1 5Gb s Pin Assignment Pin Assignment Pt mm 2 e 7j L3 m A Bmwd JSAWUSWS 5 Rx 5 Be L7 jen 1 M7VIZ SATA CHAPTER 3 HEADERS amp JUMPERS SETUP 3 1 HOW TOSETUP JUMPERS The illustration shows how to set up jumpers When the jumper cap is placed on pins the jumperis close if not that means the jumperis open Pin opened Pin dosed Pin1 2 closed 52 DETAIL SETTINGS Front Panel Audio Header JE AUDIOI This header allows user to connect the front audio out put cable with the PC front panel It will disable the output on back panel audio connectors El AE AUDIOT Pin _ Pin 1 Mic in center round Mic power Bass udio power H Right me guv Speaker out g ight line out Speaker out Right 8 Resew ed Key 9 Left line out Speaker out Left 10 Left line out Speaker out Left
13. slots FDD1 Floppy Disk connector JCI1 Chassis open header JPANEL1 Front panelfacilities header JSFAN1 Power headerf or system f an SATA1 SATA2 On board serial ATA connectors JUSB1 JUSB2 Front USB ports headers IDE1 IDE2 Hard Disk connector JCLK1 CPU Frequency selection DDRA1 DDRA2 DDR memory modules JCMOS1 Clear CMOS header M7VIZ SATA CHAPTER 2 HARDWARE INSTALLATION 2 1 CENTRAL PROCESSING UNIT CPU Step 1 Pull the lever sideways away from the socket and then raise the lever up to a 90 degree angle Step 2 Look for the white dot cut edge The white dot cut edge should point wards the lever pivot The CPU will fit only in the correct orientation Step 3 Hold the CPU down firmly and then dose the lever to complete the installation Step 4 Put the CPU Fan on the CPU and buckle it Connect the CPU fan power cable to the JCFAN1 This completes the installation 2 2 FAN HEADERS CPU FAN Power Header JCFANI Pin Assignment System Fan Power Header JSFAN 1 Pin Assignment 2 12V FAN RPM rate sense M7VIZ SATA North Bridge Fan Power Header JN BFA N 1 optional Pin Assignment Bi em FAN RPM rate sense Note The JCFAN1 JSFAN1and JNBFAN 1 support system coolingf an with Smart Fan Control utility It supports 3 pin head connector When connecting with wires onto connectors please note that the red wire is the positiv e and should
14. 1 n Ehre 12 Right line in Rear speaker Right eft line in Rear speaker Left eft line in Rear speaker Left CD ROM Audio in Connector JCDIN1 This connector allows user to connect the audio source from the variety devices like CD ROM DVD ROM PCI sound card PCITV turner card etc Left channel input Pin B Ground T JCDIN1 G round Right channel input M7VIZ SATA Digital Audio out Connector JS PDIF1 optional This connector will allow user to connect the PCI bracket SPDIF output header ES REENEN Le JSPDIF OUT SPDIF OUT Chassis O pen Header ICH This connector allows sy stem to monitor PC case open status If the signal has been triggered it will record to the CMOS and show the message on next boot up Pin Assignment Tea JCH Case open signal ATX Power Source Connectors JATXPW R1 JATXPWR 1 This connector allows user to connect 20 pin power connectoron the ATX power supply Pin Assignment Pin Assignment 2 svi pev A 5V PS ON uev 000 2 s Bod round jp o Ground ek 3 15 9 Standby VoiagesSV zi pSV E JAXPWRI ANATA WC CH GK etc es LI 11 M7VIZ SATA Header for Front Panel Facilities JPANELI This 24 pin connector indudes Power on Reset HDD LED PowerLED Sleep button speaker and IrDA Connection It allows user to connect the PC case s front panel switch functions PWR_LED JPANEL1 EE
15. 5 l4 Motherboard Component sess 6 Chapter 2 Hardware Installation 7 2 1 Central Processing Unit CRU 7 2 2 Fari Headers seen rere RR ARA Rad 7 2 3 Memory Modules Installation 0 0 0 0 eee 8 24 Connectors and Slots AAA 9 Chapter 3 Headers amp Jumpers Setup 10 3 1 How to setup JUMPETS ee eee ee ee eeeeeeeeeeeeeeeenaaeeeeananees 10 3 2 Detail SettindS A eee 10 Chapter 4 Useful Help ccr 14 4 1 Award BIOS Beep Code 14 4 2 Extra Information sse 14 4 3 Troubleshooting sess 16 M7VIZ SATA CHAPTER 1 INTRODUCTION 1 1 MOTHERBOARD FEATURES A Hardware CPU I Supports Socket A E Supports single AM D Athlon Duron Sem pron Family processor E Front Side Bus at 200 266 333 MHz Chipset I North Bridge VIA KM400 I South Bridge VIAVT8237R Dimensions I AT X Form Factor 19 4cm W X 24 4cm L Main Memory I Supports up to 2 DDR devices Supports SPD DDR 200 266 333 400 MHz without ECC DDR devices I Maximum memory size is 2GB DIMM Socket Total Memory RES Size MB DDR2 64MB 128MB 256MB 512MB 1GB 1 DDR1 64MB 128MB 256MB 512MB 1GB 1 Max is 2GB On board IDE I 2 on board connectors support 4 IDE disk drives E Supports PIO mode 4 Master Mode and Ultra DMA 33 66 1 00 133 Bus Master Mode Slots E Three 32bit PCI bus master slots I One CNR slot o
16. 7 Min 8 Min 9 Min 10 Min 11 Min 12 Min 13 Min 14 Min 15Min Suspend Mode The item allows you to select the suspend type under ACPI operating system The Choices Disabled default 1 Min 2 Min 4 Min 6 Min 8 Min 10 Min 20 Min 30 Min 40 Min 1 Hour Video Off Option This field determines when to activate the video off feature for monitor power management The Choices Suspend Off default Always on Video Off Method This option determines the manner in which the monitor is goes blank V H SYNC Blank default This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS Initial display power management signaling The Choices Stop Grant PwrOn Suspend 22 M7VIZ SATA BIOS Setup Modem Use IRQ This determines the IRQ which can be applied in MODEM use The Choices 3 default 4 5 7 9 10 11 NA Run VGABIOS if S3 Resume Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state The system time is shortened if you disable the function but system will need AGP driver to initialize the card So if the AGP driver of the VGA card does not support the initialization feature the display may work abnormally or not function after S3 The Choices Auto Yes default No Soft Off by PW R B
17. I Clock Vale M7VIZ SATA C Auto overclock button User can dick this button and WarpSpeeder M will set the best and stable performance and frequency automatically WarpSpeeder utility will execute a series of testing until system fail Then system will do fail safe reboot by using Watchdog function After reboot the WarpSpeeder utility will restore to the hardware default setting orload the verified best and stable frequency according to the Recovery Dialog s setting d Verify button User can dick this button and WarpSpeeder will proceed a testing for current frequency If the testing is ok then the current frequency will be saved into system registry If the testing fail system will do a fail safe rebooting After reboot the WarpSpeeder utility will restore to the hardware default setting orload the verified best and stable frequency according to the Recovery Dialog s setting Note Because the testing programs invoked in Auto overclock and Verify include DirectDraw Direct3D and DirectShow tests the DirectX 8 1 or newer runtime library is required And please make surey our display card s color depth is High color 16 bit or True color 24 32 bit that is required f or Direct3D rendering 5 Hardware Monitor Panel Click the Hardware Monitor button in Main Panel the button will be highlighted and the Hardware Monitor panel will slide out to left as the following figure In this pa
18. M7VIZ SATA FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications There is no guarantee that interference will not occur in a particular installation The vendor makes no representations or warranties with respect to the contents here ands pecially disclaims any implied warranties of merchantability or fitness for any purpose Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand Duplication of this publication in part orin whole is not allowed without first obtaining the vendor approval in writing The content of this users manual is subject to be changed without notice and we will not be responsible for any mistakes found in this users manual All the brand and product names are trademarks of their respective companies Table of Contents Chapter 1 Introduction rere 1 1 1 Motherboard Features 1 1 2 Package Checklist eese 4 1 3 Motherboard Layout
19. Meaning One long beep followed by two short Video card not found orv ideo card beeps memory bad High low siren sound CPU overheated System will shut down automatically One Short beep when system boot up No error found during PO ong beeps every other second No DRAM detected or install 4 2 EXTRA INFORMATION A BIOS Update After you fail to update BIOS or BIOS isinvaded by virus the Boot Block function will help to restore BIOS If the following message is shown after boot up the system it means the BIOS contents are corrupted In this Case please follow the procedure below to restore the BIOS 2 P Oro eg Make a bootable floppy disk Download the Flash Utility AWDFLASH exe from the Biostar website www biostar com tw Confirm motherboard model and download the respectively BIOS from Biostar website Copy AWDFLASH exe and respectively BIOS into floppy disk Insert the bootable disk into floppy drive and press Enter System will boo up to DOS prompt Type Awdflash xxxx bf sn py r in DOS prompt System will update BIOS automatically and restart The BIOS has been recovered and will work properly 14 M7VIZ SATA B CPU Overheated If the system shutdown automatically after poweron system for seconds that means the CPU protection function has been activated When the CPU is over heated the motherboard will shutdown automatically to avoid a damage of the CPU and the system may not power
20. OS Installed No Reset Configuration Data Disabled Resources Controlled By AutoCESCD gt Select Yes if you are using a Plug and Play PCI UGA Palette Snoop Disabled capable operating Assign IRQ For UGA Enabled system Select No if Assign IRQ For USB Enabled you need the BIOS to configure non boot devices Tiee Move Enter Select PU PD Ualue Fi Save ESC Exit Fi General Help FS5 Previous Values F Optimized Defaults PNP OS Installed When set to YES BIOS will only initialize the PnP cards used for the boot sequence VGA IDE SCSI The rest of the cards will be initialized by the PnP operating system like Window 95 When set to NO BIOS will initialize all the PnP cards For non PnP operating systems DOS Netware this option must set to NO The Choices No default Yes 25 M7VIZ SATA BIOS Setup R eset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict Every peripheral device has a node which is called ESCD This node records which resources are assigned to it The system needs to record and update ESCD to the memory locations These locations 4K are reserved in the system BIOS If the Disabled default option is chosen the system s ESCD will update only when the new configuration varies from the last one If the Enabled option is chosen the system is forced to update ESCDs
21. S Setup P CI VGA Palette Snoo Choose Disabled or Enabled Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility However the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors and the graphic controller needs to know what is in the palette of the VGA controller To do this the non VGA graphic controller watches for the Write access to the VGA palette and registers the snoop data In PCI based systems where the VGA controller is on the PCI bus and a non VGA graphic controller is on an ISA bus the Write Access to the palette will not show up on the ISA bus if the PCI VGA controller responds to the Write In this case the PCI VGA controller should not respond to the Write it should only snoop the data and permit the access to be forwarded to the ISA bus The non VGA ISA graphic controller can then snoop the data on the ISA bus Unless you have the above situation you should disable this option Disabled default Disables the function Enabled Enables the function Assign IRQ For VGA This item allows the users to choose which IRQ to assign for the VGA The Choices Enabled default Disabled Assign IRQ For USB This item allows the users to choose which IRQ to assign for the USB The Choices Enabled defaul
22. TTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The Choices Delay 4 Sec Instant Off default PWRON After PW R Fail The Choices OFF default ON IRQ Event Activity Detect If you highlight the literal Press Enter next to the IRQ Event Activity Detect label and then press the enter key it will take you a submenu with the following options USB Resume from s3 The Choices Disabled default Enabled VGA When set to On any event occurring at a VGA Port will awaken a system which has been powered down The Choices Off default On LPT amp COM When this option is set to On any event occurring at a COM serial LPT printer port will awaken a system which has been powered down The Choices LPT COM default COM LPT NONE HDD amp FDD When this option is set to On any event occurring on a hard drive or a floppy drive will awaken a system which has been powered down The Choices On default Off PCI Master When set to On you need a LAN add on card which supports the power function It should also support the wake up on LAN jump The Choices Off default On 23 M7VIZ SATA BIOS Setup PowerOn by PCI Card When you select Enabled a PME signal from PCI card returns the system to Full ON state The Choices Disabled default Enabled Wake Up On LAN Ring To use this function you need a LAN a
23. The Choices Disabled default Enabled AGP Master 1 WS Read When Enabled read to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled AGP 3 0 calibration cycle The Choices Enabled default Disabled Enabled VGA share Memory size The Choices 32M default 15 M7VIZ SATA BIOS Setup CPU amp PCI Bus Control If you highlight the literal Press Enter next to the CPU amp PCI Bus Control label and then press the enter key it will take you a submenu with the following options PCI Master 0 WS Write When enabled writes to the PCI bus are executed with zero wait states The Choices Enabled default Disabled PCD Master 0 WS Write When enabled writes to the AGP bus are executed with zero wait states The Choices Enabled default Disabled PCII Post Write When Enabled CPU writes are allowed to post on the PCI bus The Choices Enabled default Disabled PCD Post Write When Enabled CPU writes are allowed to post on the AGP bus The Choices Enabled default Disabled VLink 8X Support This item allows you to enable or disable VLink 8X support The Choices Enabled default Disabled PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification The Choices Enabled default Disabled Memory Hole When enable
24. a time The Choices Half default Full Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O Address The Choices 378 IRQ7 default 278 IRQ5 3BC IRQ7 Disabled Parallel Port Mode The default value is SPP The Choices SPP default Using Parallel port as Standard Printer Port EPP Using Parallel Port as Enhanced Parallel Port ECP Using Parallel port as Extended Capabilities Port 19 M7VIZ SATA BIOS Setup ECP EPP Using Parallel port as ECP amp EPP mode ECP Mode Use DMA Select a DMA Channel for the port The Choices 3 default 1 Init Display First With systems that have multiple video cards this option determines whether the primary display uses a PCI Slot or an AGP Slot The Choices PCI Slot default AGP 20 M7VIZ SATA BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up power down features W Figure 6 Power Management Setup Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI function Enabled ACPI Suspend Type S1 P085 1 Power Management Option User Define Menu Level gt HDD Power Down Disable Suspend Mode Disable Video Off Option Suspend gt Off Video Off Method U H SYNC Blank MODEM Use IRQ 3 Run YGABIOS if 3 Resume Yes Soft Off by PWRBIN Instant Off PWRON After PWR
25. ace select Disabled to deactivate an interface If you highlight the literal Press Enter next to the Onchip IDE Control label and then press the enter key it will take you a submenu with the following options Onchip SATA The Choices Enabled default Disabled IDE DMA transfer access The Choices Enabled default Disabled OnChip IDE Channel 0 1 The motherboard chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the first and or second IDE interface Select Disabled to deactivate an interface if you are going to installa primary and or secondary add in IDE interface The Choices Enabled default Disabled IDE Prefetch Mode The onboard IDE drive interfaces supports IDE prefetching for faster drive access If the interface does not support prefetching If you install a primary and or secondary add in IDE interface set this option to Disabled The Choices Enabled default Disabled IDE Primary Secondary Master Slave PIO 17 M7VIZ SATA BIOS Setup The IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the IDE devices that the onboard IDE interface supports Modes 0 through 4 provides successively increased performance In Auto mode the system automatically determines the best mode for each device The Choices Auto default Mode0 Model Mode2 Mode3 Mode4 IDE Primary Secondary Master
26. atically rebooting the computer and then restart to a speed that is either the original system speed or a suitable one 52 SYSTEM REQUIREMENT OS Support Windows 98 SE Windows Me Windows 2000 Windows XP DirectX DirectX 8 1 or above The Windows XP operating system indudes DirectX 8 1 If you use Windows XP you do not need to install DirectX 8 1 17 M7VIZ SATA 5 3 INSTALLATION 1 Execute the setup execution file and then the following dialog will pop up Please dick Next button and follow the default procedure to install tee oe Ir fea bel Wired le aps pee Tip Or beh io ipn rell eal o emen ye oT oe Hes 2 When you see the following dialog in setup procedure it means setup is completed If the Launch the WarpSpeeder Tray Utility checkbox is checked the Tray Icon utility and WarpSpeeder utility will be automatically and immediately launched after you dick Finish button Vrat ida Ful ood E cr deis Satu ha rz hasc rct aleng e ap sers En poa compel RH Lesen te epg ve ba Usage The following figures are just only for reference the screen printed in this user manual will change according to your motherboard on hand 18 M7VIZ SATA 5 4 WARPSPEEDER M INCLUDES 1 TRAY ICON AND 5 PANELS 1 Tray Icon Whenever the Tray Icon utility is launched it will display a little tray icon on the right side of Windows Taskbar BD V 11 33 aM This utility is responsible for c
27. be connected to pin 2 and the black wire is Ground and should be connected to GND 23 MEMORY MODULES INSTALLATION 2 2 1 DDR M odule installation 1 Unlocka DIMM slot by pressing the retaining dips outward Align a DIMM on the slot such thatthe notch on the DIMM matches the break on the Slot 2 Insert the DIMM vertically and fimlyinto the slot until the retaining chip snap back in place and the DIMM is propery seated M7VIZ SATA 2 4 CONNECTORS AND SLOTS Floppy Disk Connector FDD1 The motherboard provides a standard floppy disk connector that supports 360K 720K 1 2M 1 44M and 2 88M floppy disk types This connector supports the provided floppy drive ribbon cables Hard Disk Connectors IDE1 IDE2 The motherboard has a 32 bit Enhanced PCI IDE Controller that provides PIO Mode 0 5 Bus Master and Ultra DMA 33 66 100 133 functionality It has two HDD connectors IDE1 primary and IDE2 secondary The IDE connectors can connect a master and a slave drive so you can connect up to four hard disk drives The first hard drive should always be connected to IDE1 Peripheral Component Interconnect Slots PCI1 PCI3 This motherboard is equipped with 3 standard PCI slots PCI stands for Peripheral Component Interconnect and itis a bus standard for expansion cards This PCI slotis designated as 32 bits Accelerated Graphics Port Slot AGP1 Your monitor will attach directly to that video card This motherboard supports video cards
28. change them Enter Password Save amp Exit Setup Save all configuration changes to CMOS memory and exit setup Confirmation message will be displayed before proceeding SAVE to CHOS and EXIT V N V Exit Without Saving Abandon all changes made during the current session and exit setup confirmation message will be displayed before proceeding Quit Without Saving Y N N Upgrade BIOS This submenu allows you to upgrade bios BIOS UPDRTE UTILITV V N N M7VIZ SATA BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item W Figure 2 Standard CMOS Setup Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Time hh mm ss gt 18 951 5 56 Menu Level L gt IDE Primary Master gt IDE Primary Slave Change the day month k IDE Secondary Master year and century gt IDE Secondary Slave Drive A 1 44M 3 5 in Drive B None 1 Video LEGA UGA Halt On A11 But Keyboard Ti e Move Enter Select PU PD Ualue d Eure ESC Exit Fi General Help F5 Previous Values timized Defaults M7VIZ SATA BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu
29. che Depending on the CPU chipset in use you may be able to increase memory access time with this option Enabled default Enable cache Disabled Disable cache External Cache This option enables or disables Level 2 secondary cache on the CPU which may improve performance Enabled default Enable cache Disabled Disable cache CPU L2 Cache ECC Checking This item allows you to enable disable CPU L2 Cache ECC Checking The Choices Enabled default Disabled Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution Enabled default Optional ROM is enabled Disabled Optional ROM is disabled 10 M7VIZ SATA BIOS Setup Virus Warning This option allows you to choose the Virus Warning feature that is used to protect the IDE Hard Disk boot sector If this function is enabled and an attempt is made to write to the boot sector BIOS will display a warning message on the screen and sound an alarm beep Disabled default Virus protection is disabled Enabled Virus protection is activated Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self Test POST to execute after you power up the computer Enabled default Enable quick POST Disabled Normal POST Boot Up NumLock Status Selects the NumLock State after power on On default Numpad is number keys Off Numpad is arrow keys Gate A20 Option Select if chipset or keyboar
30. d you can reserve an area of system memory for ISA adapter ROM When this area is reserved it cannot be cached Refer to the user documentation of the peripheral you are installing for more information The Choices Disabled default 15M 16M System BIOS Cacheable Selecting the Enabled option allows caching of the system BIOS ROM at F0000h FFFFFh which can improve system performance However any programs writing to this area of memory will cause conflicts and result in system errors The Choices Enabled Disabled default Video RAM Cacheable Enabling this option allows caching of the video RAM resulting in better system performance However if any program writes to this memory area a system error may result The Choices Enabled Disabled default 16 M7VIZ SATA BIOS Setup 5 Integrated Peripherals eg enpnera Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals gt UIA OnChip IDE Device Press Enter gt UIA OnChip PCI Device Press Enter gt SuperlO0 Device Press Enter Menu Level gt Init Display First PCI Slot tile Move Enter Select PU PD Value Fi Save ESC Exit F1 General Help F 0 F5 Previous Values timized Defaults VIA OnChip IDE Device The chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the first and or second IDE interface If you install a primary and or secondary add in IDE interf
31. d controller should control Gate A20 Normal A pin in the keyboard controller controls Gate A20 Fast default Lets chipset control Gate A20 Typematic Rate Setting When a key is held down the keystroke will repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be configured Disabled default Enabled Typematic Rate Chars Sec Sets the rate at which a keystroke is repeated when you hold the key down The Choices 6 default 8 10 12 15 20 24 30 Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke The Choices 250 default 500 750 1000 11 M7VIZ SATA BIOS Setup Security Option This option will enable only individuals with passwords to bring the system online and or to use the CMOS Setup Utility System A password is required for the system to boot and is also required to access the Setup Utility Setup default A password is required to access the Setup Utility only This will only apply if passwords are set from the Setup main menu MPS Version Control For OS The BIOS supports version 1 1 and 1 4 of the Intel multiprocessor specification Select version supported by the operation system running on this computer The Choices 1 4 default 1 1 OS Select For DRAM gt 64MB A choice other than Non OS2 is only used for OS2 systems with memory exceeding 64MB The Choices Non OS 2 defa
32. dd on card which support power on function It should also support the wake up on LAN jump Disabled default Wake up on LAN Ring not supported Enabled Wake up on LAN Ring supported RTC Alarm Resume When Enabled you can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode The Choices Enabled Disabled default IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events i e wake on LPT amp COMM activity Primary INTR On IRQ3 COM2 Enabled IRQ4 COMI Enabled IRQS LPT2 Enabled IRQ6 Floppy Disk Enabled IRQ7 LPT1 Enabled IRQ8 RTC Alarm Disabled IRQ9 IRQ2 Redir Disabled IRQIO Reserved Disabled IRQII Reserved Disabled IRQI2 PS 2 Mouse Enabled IRQ13 Coprocessor Enabled IRQ14 Hard Disk Enabled IRQI5 Reserved Disabled 24 M7VIZ SATA BIOS Setup 7 PnP PCI Configurations This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings W Figure 7 PnP PCI Configurations Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Menu Level Le PNP
33. ecovery Time This item allows you to select the recovery time The Choices 2T 3T default tWTR for DDR400 only This item allows you to choose tWTR for DDR 400 only The Choices 1T 2T 3T default 14 M7VIZ SATA BIOS Setup AGP amp P2P Bridge Control If you highlight the literal Press Enter next to the AGP amp P2P Bridge Control label and then press the enter key it will take you a submenu with the following options AGP Aperture Size Select the size of the Accelerated Graphics Port AGP aperture The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The Choices 64M 256M 128M default 32M 16M 8M 4M AGP Mode This item allows you to select the AGP Mode The Choices 4X default 2X 1X AGP Driving Control By choosing Auto the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card By choosing Manual it allows user to set AGP output Buffer Drive strength P Ctrl by manual The Choices Auto default Manual AGP Driving Value While AGP driving control item set to Manual it allows user to set AGP driving The Choices DA default AGP Fast Write The Choices Enabled Disabled default AGP Master 1 WS Write When Enabled writes to the AGP Accelerated Graphics Port are executed with one wait states
34. he hard disk drives and video monitors can be managed by this AWARD BIOS ACPI Support Award ACPI BIOS support Version 1 0 of Advanced Configuration and Power interface specification ACPI It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification developed by Microsoft Intel and Toshiba M7VIZ SATA BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2 1 of the Intel PCI Peripheral Component Interconnect local bus specification DRAM Support DDR SDRAM Double Data Rate Synchronous DRAM are supported Supported CPUs This AWARD BIOS supports the AMD CPU Using Setup In general you use the arrow keys to highlight items press Enter to select use the lt PgUp gt and lt PgDn gt keys to change entries press F1 for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program by using the keyboard Keystroke Function Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item on the left menu bar Right arrow Move to the item on the right menu bar Move Enter Move to the item you desired PgUp key Increase the numeric value or make changes PgDnkey Decrease the numeric value or make changes Key Increase the numeric value or make changes Key Decrease the numeric value or make changes Esc key Ma
35. in Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit Current page and return to Main Menu F1 key General help on Setup navigation keys F5 key Load previous values from CMOS F7 key Load the optimized defaults F10 key Save all the CMOS changes and exit M7VIZ SATA BIOS Setup 1 Main Menu Once you enter Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu JI WARNING The information about BIOS defaults on manual Figure 1 2 3 4 5 6 7 8 9 is just for reference please refer to the BIOS installed on board for update information W Figure 1 Main Menu Phoenix AwardB CMOS Setup Utility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status Upgrade BIOS Quit F9 Menu TETE Select Item Save amp Exit Setup Time Date Hard Disk Type Standard CM OS Features This submenu contains industry standard configurable options Advanced BIOS Features This submenu allows you to configure enhanced features of the BIOS
36. nel Click the Voltage button in Main Panel the button will be highlighted and the Voltage Panel will slide out to up as the following figure In this panel you can dedde to increase CPU core voltage and Memory voltage or not The default setting is No If you wantto get the best performance of overdocking we recommend you dick the option Yes 21 M7VIZ SATA 4 Overclock Panel Clickthe Overclock button in Main Panel the button will be highlighted and the Overclock Panel will slide out to left as the following figure E 3 fetes IA Fiecuvere Dose PA ZS UE t m asse i NULL Deco u TY U 3M Hz Buton WEE Bitze IHH once RA nem O verclock Panel contains the these features a 3MHz button 1MHz button 1MHz button and 3M Hz button provide user the ability to do real time overdock adjustment Warning Manually overclock is potentially dangerous especially when the overclocking percentage is over 110 We strongly recommend you verity ev ery speed you overclock by click the Verify button Or you can just click Auto ov erclock button and let WarpSpeeder M automatically gets the best resultfory ou b Recovery Dialog button Pop up the following dialog Let user select a restoring way if system need to do a fail safe reboot Peeg zer a nacer akon dial vill decida whal kel of cloning you pd lo do ater sytem Lai cafe reboot Oper Group C Rendre bo Hedw D elut CPL
37. nel you can get the real time status information of your system The information will be refreshed every 1 second A E Em Tia N 868 oom M7VIZ SATA 6 About Panel Click the about button in Main Panel the button will be highlighted and the About Panel will slide out to up as the following figure In this panel you can get model name and detail infomation in hints of all the chipset that are related to overclocking You can also get the mainboard s BIOS model and the Version number of WarpSpeeder utility LE chu EEE MHz 24 M7VIZ SATA Note Because the overclock overvoltage and hardware monitor features are controlled by several separate chipset WarpSpeeder divide these features to separate panels If one chipset is not on board the correlative button in Main panel will be disabled but will not interfere other panels functions This property can make WarpSpeeder utility more robust 25 M7VIZ SATA BIOS Setup BIOS SE TEE IB Maiti ldem EE 3 Standard CMS Features er enter ertet per 6 3 Advanced BIOS Features uod e t BC er CO Rete dt exe 9 4 Advanced Chipset Features 13 5 Integrated Peripherals vini ert mere doen 17 6 Power Management Setup esses eene emen 21 T PnP PCI Configurations ine P op Ht deer ane 25 8 PC EHealth Status eerte tt e be e teat eee i e we 28 9 Frequency Voltage Control eene 30 M7VIZ SATA BIOS Setup
38. nly Type B I One AGP 8X slot M7VIZ SATA Super 1 0 i Chip ITE8705F I Provides the mos commonly used legacy Super VO functionality I Environment Control initiatives H WMonitor TEs Smart Guardian function Serial ATA I Integrated in VT 8237R I Two serial ATAconnedors support 2 SATAdevices I Supports RAID 0 and RAID 1 functions I Supports 2 serial ATA SATA ports Data transfer rates up to 150 MB s Complaints with SATA Version 1 0 specification LAN PHY L Chip VIAVT6103 I Supports 10 Mb s and 100 Mb s auto negotiati on I Half Full duplex capability On board AC 97 Audio Sound Codec E Chip CMI9761A I Compliant with AC 97 spedfication I Supports 6 channels I Supports digital audio out functions optional Internal On board Connectors and Headers 1 front panel header supports front panel facilities 1 CD in connector supports CD ROM audioin function 1 front audio header supports front panel audio function 1 SPDIF out connector supports digital audio out function 1 floppy connector supports 2 FDD devices with 360K 720K 1 2M 1 44M and 2 88Mbytes I 2 IDE connectors support 4 IDE disk drives I 2 Serial ATA connedors support 2 SATA devices I 2 USB headers support 4 USB 2 0 ports at front panel M7VIZ SATA Rear Back Panel Side C onnectors 4 USB 2 0 ports 1 VGAport 1 Serial port 1 RJ 45 LAN jack 1 PS 2 Mouse amp Keyboard port 1 Parallel port SPP EPP ECP mode 1
39. on again In this case please double check 1 The CPU cooler surface is placed evenly with the CPU surface 2 CPUfanisrotated normally 3 CPU fan speed is fulfilling wth the CPU speed After confirmed please follow steps below to relief the CPU protection function 1 Remove the power cord from power supply for seconds 2 Waitfor seconds 3 Pluginthe power cord and boot up the system Or you can 1 Clearthe CMOS data See Close CMOS Header JCMOS1 section 2 Waitfor seconds 3 Power on the system again M7VIZ SATA 4 3 TROUBLES HOOTING Probable Solution No power to the system at all Make sure power cable s Power light don t illuminate f an securely plugged in inside power supply does not turnj2 Replace cable on 3 Contact technical support Indicator light on key board does not turn on System inoperativ e Keyboard lights Using even pressure on both ends of are on power indicator lights are lit the DIMM press down firmly until the and hard drive is spinning module snaps into place System does not boat from hard dek 1 Check cable running from disk to drive can be bootedf rom optical driv e disk controller board Make sure both ends are securely plugged in check the driv e type in the standard CMOS setup Backing up the hard drive is extremely important All hard disks are capable of breaking down at any time System only bootsfrom optical drive Back up data and applications
40. onveniently invoking WarpSpeeder Utility You can use the mouse by clicking the left button in order to invoke WarpSpeeder directly from the little tray icon or you can right click the little tray icon to pop up a popup menu as following figure The Launch Utility item in the popup menu has the same function as mouse left click on tray icon and Exit item will dose Tray Icon utility if selected Lanuch Utility L Est fer Sere aes 19 M7VIZ SATA 2 Main Panel If you click the tray icon WarpSpeeder utility will be invoked Please referto the following figure the utility s first window you will see is Main Panel Main Panel contains features as follows a Display the CPU Speed CPU external dock Memory dock AGP dock and PCI dock infomation b ContainsAbout Voltage Overclock and Hardware Monitor Buttons for invoking respective panels c With a user friendly Status Animation it can represent 3 overclock percentage stages Man walking overdock percentage from 10096 110 96 Panther running overclock percentage from 11096 120 Car racing overclock percentage from 120 above 4 We o ORIN P SPEED MHz AG m x Bo KT CE 333 chy CLOCK MHz PCICLOCK MHz f a MEMORY CLOCK Hardware Monitor Button L La F Over clock percentage 100 E Overclock B lllon 66 5 MHz SOEN 132 7 DE 100 MHz Voltage Button dO V 1146 AM M7VIZ SATA 3 Voltage Pa
41. quency Voltage Control Menu Level gt fi Move Enter Select PU PD Ualue Fi Save ESC Exit Fi General Help F5 Previous Values F Optimized Defaults CPU Clock This item allows you to select CPU Clock and CPU over clocking If unfortunately the system s frequency that you are selected is not functioning there are two methods of booting up the system Method 1 Clear the COMS data by setting the JCOMS1 2 3 closed as ON status All the CMOS data will be loaded as defaults setting Method 2 Press the Insert key and Power button simultaneously after that keep on pressing the lt Insert gt key until the power on screen showed This action will boot up the system according to FSB of the processor X It s strongly recommended to set CPU Vcore and clock in default setting If the CPU Vcore and clock are not in default setting it may cause CPU or M B damage 30
42. t Disabled 27 M7VIZ SATA BIOS Setup 8 PC Health Status W Figure 8 PC Health Status noenix A wardBbl 0 MO etup PC Health Status Shutdown Temperature Enabled Menu Level Ld Show H W Monitor in POST Enabled Chassis Open Warnning Disabled Tlee Move Enter Select PU PD Value F1i Save ESC Exit Fi General Help FS5 Previous Values F Optimized Defaults Shutdown Temperature This item allows you to set up the CPU shutdown Temperature This item only effective under ACPI mode The Choices Disabled default enable CPU Veore 3 3 V 5 0 V 12V 5VSB Voltage Battery Detect the system s voltage status automatically Current CPU Temperature This field displays the current temperature of the CPU Current CPU FAN Speed This field displays the current speed of CPU fan Current SYS FAN Speed This field displays the current speed SYSTEM fan 28 M7VIZ SATA BIOS Setup Show H W Monitor in POST If your computer contains a monitoring system it will show PC health status during POST stage The item offers several delay time for you to choose The Choices Enabled default Disabled Chassis Open Warning This item allows you to enable or disable Chassis Open Warning beep The Choices Disabled Default Enabled 29 M7VIZ SATA BIOS Setup 9 Frequency Voltage Control W Figure 9 Frequency Voltage Control Phoenix AwardBIOS CMOS Setup Utility Fre
43. ult OS2 Summary Screen Show This item allows you to enable disable display the Summary Screen Show The Choices Disabled default Enabled 12 M7VIZ SATA BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system This chipset manage bus speeds and access to system memory resources such as DRAM It also coordinates communications with the PCI bus The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly W Figure 4 Advanced Chipset Setup Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features gt DRAM Clock Drive Control Press Enter gt AGP amp P2P Bridge Control gt CPU amp PCI Bus Control Menu Level Ls Memory Hole i ID System BIOS Cacheable Disabled Video RAM Cacheable Disabled tiee Move Enter Select PU PD Ualue Fi Save ESC Exit Fi General Help F F5 Previous Values Optimized Defaults DRA M Clock Drive Control To control the Clock Drive If you highlight the literal Press Enter next to the DRAM Clock Drive Control label and then press the enter key it will take you a submenu with the following options DRAM Clock This item determines DRAM clock following 100MHz 133MHz 166MHz or By SPD The Choices 100MHz 133MHz By SPD default 166MHz
44. ures W Figure 3 Advanced BIOS Setup Phoenix AwardbloO MO etup Advanced BIOS Features k Boot Seq amp Floppy Setup Press Enter k Cache amp Shadow Setup Press Enter Virus Warning Disabled Menu Level Le Quick Power On Self Test Enabled Boot Up NumLock Status On Gate fi28 Option Fast Typematic Rate Setting Disabled Security Option Setup MPS Version Control For 08 1 41 OS Select For DRAM gt 64MB Non 08 2 Summary Screen Show Disabled Tle Move Enter Select PU PD Value Fi Save ESC Exit Fi General Help F5 Previous Values F Optimized Defaults Boot Seq amp Floppy Setup This item allows you to setup boot seq amp Floppy First Second Third Boot Other Device These BIOS attempt to load the operating system from the devices in the sequence selected in these items The Choices Floppy LS120 HDD 0 SCSI CDROM HDD 1 HDD 2 HDD 3 ZIP 100 USB FDD USB ZIP USB CDROM USB HDD LAN Disabled Swap Floppy Drive For systems with two floppy drives this option allows you to swap logical drive assignments The Choices Disabled default Enabled Boot Up Floppy Seek Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks Disabling this option reduces the time it takes to boot up The Choices Enabled default Disabled M7VIZ SATA BIOS Setup Cache amp Shadow Setu This item allows you to setup cache amp shadow setup CPU Internal Ca
Download Pdf Manuals
Related Search