Home

Biostar M7VIT Pro Owner's Manual

1. M7VIT Pro BIOS Setup 5 Integrated Peripherals m Figure 5 Integrated Peripherals VIA OnChip IDE Device VIA OnChip PCI Device Super IO Device Init Display First OnChip USB Controller USB Keyboard Support USB Mouse Support IDE HDD Block Mode Press Enter Press Enter Press Enter PCI Slot All Enabled Disabled Disabled Enabled Item Help Henu Level VIA OnChip IDE Device The chipset contains a PCI IDE interface with support for two IDE channels Select Enabled to activate the first and or second IDE interface If you install a primary and or secondary add in IDE interface select Disabled to deactivate an interface If you highlight the literal Press Enter next to the Onchip IDE Control label and then press the enter key it will take you a submenu with the following options OnChip IDE Channel 0 1 The motherboard chipset contains a PCI IDE interface with support for two IDE chamnels Select Enabled to activate the first and or second IDE interface Select Disabled to deactivate an interface if you are going to install a primary and or secondary add in IDE interface The Choices Enabled default Disabled IDE Prefetch Mode The onboard IDE drive interfaces supports IDE prefetching for faster drive access If the interface does not support prefetching If you install a primary and or secondary add in IDE interface set this option t
2. after S3 The Choices Auto Yes default No Soft Off by PWR BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The Choices Delay 4 Sec Instant Off default IRQ E vent Activity Detect If you highlight the literal Press Enter next to the IRQ Event Activity Detect label and then press the enter key it will take you a submenu with the following options USB Resume from S3 This item allows you to enable or disable USB Resume from S3 The Choices Disabled defautl Enabled VGA When set to On any event occurring at a VGA Port will awaken a system which has been powered down The Choices Off default On LPT amp COM When this option is set to On any event occurring at a COM serial LPT printer port will awaken a system which has been powered down The Choices LPT COM default COM LPT NONE HDD amp FDD When this option is set to On any event occurring on a hard drive or a floppy drive will awaken a system which has been powered down The Choices On default Off 23 M7VIT Pro BIOS Setup PCI Master When set to On you need a LAN add on card which supports the power function It should also support the wake up on LAN jump The Choices Off default On PowerOn by PCI Card When you select Enabled a PME signal from PCI card returns the system to Full ON state The Choices Disabled de
3. Define Menu Level gt HDD Power Down Disable Suspend Mode Disable Video Off Option Suspend gt Off Video Off Method H SYNC Blank MODEM Use IRQ 3 Soft 0ff by PHRBTN Instant 0ff IRQ Event Activity Detect Press Enter ACPI function This item displays the status of the Advanced Configuration and Power Management ACPI The Choices Enabled default Disabled ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system The Choices S1 POS default Power on Suspend S3 STR Suspend to RAM S1 S3 POS STR Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes 1 HDD Power Down 2 Suspend Mode 21 M7VIT Pro BIOS Setup There are four options of Power Management three of which have fixed mode settings Min Power Saving Minimum power management Suspend Mode 1 hr HDD Power Down 15 min Max Power Saving Maximum power management only available for sl CP Us Suspend Mode 1 min HDD Power Down 1 min User Defined default Allows you to set each mode individually When not disabled each of the ranges are from 1 mm to 1 hr except for HDD Power Down which ranges from 1 min to 15 min and disable HDD Power Down When enabled the hard disk drive will power down and after a set time of system inactivity All other devices remain active Th
4. EH 10 pcr BE 7 1 9 inbond PCI SLOT mJ USBV2 1 0 PCISLOT JWOL1 EM JPANELI CNR SLOT TE JSFANI Motherboard Description CPU Installation ai ON 1 Pull the lever sideways away from the socket then raise the lever up to 90 degree angle 2 Locate Pin A inthe socket and lock for the white dot or cut edge in the CPU Match Pin A with the white dot cut edge then insert the CPU 3 Pressthe lever down Then Put thefan onthe CPU and buckle it and put the fan s power pot into the JCFAN 1 then to complete the installation CPU System Fan Headers JCFAN1 JS FANI Bn EEE eee Sere ETE MR PE RE LT FETES A H F 1 2V E f Ground Sense Ground E 12V E Sense E i e gt See DRAM Access Time 2 5V Unbuffered Registered DDR PC1600 2100 2700 3200 Ty perequired DRAM Ty pe 64MB 128MB 256MB 512MB 1GB DIMM Module 184 pin Motherboard Description DIMM Socket DDR Module Total Memory Location Size MB DIMM 1 64MB 128MB 256MB 51 2NB 1GBI 4 DIMM 2 64MB 128MB 256MB 512MB 1GB Max is 3GB DIMM3 64MB 128MB 256MB 512MB 1GB 4 gt gt The list shown abov ef or DRAM configuration is only for ref erence List of the status of DDR 400 already passed e niet as Size 1 DDR400 KINGMAX KDL684T4AA50 Double Pass Size 256M x2 Size 256M x3 3 DDR400 TwinMOS TMD7608F8E50B Pass A DDR400 W942508BH5 Pass 5 DDR400 Winbond W942508BH 5 Double Pass Size 512M x3 Dolf use FSB 33
5. PNP OS Installed No Reset Configuration Data Disabled Resources Controlled By Auto ESCD 1 Jou are Play PCI VGA Palette Snoop Disabled Assign IRQ For VGA Enabled Assign IRQ For USB Enabled PNP OS Installed When set to YES BIOS will only initialize the PnP cards used for the boot sequence VGA IDE SCSI The rest of the cards will be initialized by the PnP operating system like Window 95 When set to NO BIOS will initialize all the PnP cards For non PnP operating systems DOS Netware this option must set to NO The Choices No default Yes Reset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict Every peripheral device has a node which is called ESCD This node records which resources are assigned to it The system needs to record and update ESCD to the memory locations These locations 4K are reserved in the system BIOS If the Disabled default option is chosen the system s ESCD will update only when the new configuration varies from the last one If the Enabled 25 M7VIT Pro BIOS Setup option is chosen the system is forced to update ESCDs and then is automatically set to the Disabled mode The above settings will be shown on the screen only if Manual is chosen for the resources controlled by function Legacy is the term which signifies that a reso
6. Virus Warning Disabled Menu Level gt Quick Power On Self Test Enabled Boot Up NumLock Status On Gate A20 Option Fast Typematic Rate Setting Disabled Security Option Setup MPS Version Control For 0S 1 4 OS Select For DRAM gt 64MB Non 0 2 Summary Screen Show Disabled Boot Seq amp Floppy Setup This item allows you to setup boot seq amp Floppy First Second Third Boot Other Device These BIOS attempt to load the operating system from the devices in the sequence selected in these items The Choices Floppy LS120 HDD 0 SCSI CDROM HDD 1 HDD 2 HDD 3 ZIP 100 LAN Disabled Swap Floppy Drive For systems with two floppy drives this option allows you to swap logical drive assignments The Choices Disabled default Enabled Boot Up Floppy Seek Enabling this option will test the floppy drives to determine if they have 40 or 80 tracks Disabling this option reduces the time it takes to boot up The Choices Enabled default Disabled M7VIT Pro BIOS Setup Cache amp Shadow Setu This item allows you to setup cache amp shadow setup CPU Internal Cache Depending on the CPU chipset in use you may be able to mcrease memory access time with this option Enabled default Enable cache Disabled Disable cache External Cache This option enables or disables Level 2 secondary cache on the CPU which may improve performance Enabled default Enable cache Disabl
7. configured Disabled default Enabled Type matic Rate Chars Sec Sets the rate at which a keystroke is repeated when you hold the key down The Choices 6 default 8 10 12 15 20 24 30 Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke The Choices 250 default 500 750 1000 Security Option This option will enable only individuals with passwords to bring the system online and or to use the CMOS Setup Utility System A password is required for the system to boot and is also required to access the Setup Utility Setup default A password is required to access the Setup Utility only This will only apply if passwords are set from the Setup main menu MPS Version Control For OS The BIOS supports version 1 1 and 1 4 of the Intel multiprocessor specification Select version supported by the operation system running on this computer The Choices 1 4 default 1 1 OS Select For DRAM gt 64MB A choice other than Non OS2 is only used for OS2 systems with memory exceeding 64MB The Choices Non OS2 default OS2 Summary Screen Show This item allows you to enable disable display the Summary Screen Show The Choices Disabled default Enabled 11 M7VIT Pro BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset mstalled on your system This chipset manage bus speeds and access to s
8. la direcci n 2 Tire la leng eta hacia afuera Inserte los m dulos de memoria DIMM en el z calo a los 90 grados luego empuje hacia abajo verticalmente de modo que ercaje en el lugar i 3 Los agujeros de montaje y las leng etas pl sticas deben caber por sobre el borde y sostenga los m dulos de memoria DIMM en el lugar 16 Motherboard Description Puentes Cabezales Conectores y Ranuras Conectores del Disco Duro IDE1 IDE2 La placa madre tiene un controlador de 32 bit PCI IDE que proporciona Modo PIO 0 4 Bus Master y funcionalidad Ultra DMA 33 66 100 Tiene dos conectores HDD IDE1 primario y IDE2 secundario El conector IDE puede conectar a un master y un drive esclavo as puede conectar hasta cuatro discos r gidos El primer disco duro debe estar siempre conectado al IDE1 Conector para Disquete FDD1 La placa madre proporciona un conedor est ndar del disquete FDC que soporta 360K 720K 1 2M 1 44M y 2 88M ipos de disquete Este conector utiliza los cables de cinta proporcionados por eldisquete Ranura del Puerto Acelerado para Gr ficos AGP1 8X Su monitor se fijar directamente a latarjeta de video Esta placa madre soporta tarjetas de video para ranuras PCI y tambi n est equipado con un Puerto Acelerado para Gr icos sta tarjeta AGP tomar ventaja de la tecnolog a del AGP para el mejoramiento de la eficiencia y funcionamiento del video especialmente con gr ficos D Ran
9. to specify the delay from precharge command to activate command The Choices 2T 3T default Tras Non DDR400 DDR400 This items allows you to set Tras Non DDR400 DDR400 The Choices 7T 10T default 6T 8T 5T 6T 8T 12T Active to CMD Tred Use this item to specify the delay from the activation of a bank to the time that a read or write command is accepted The Choices 2T 3T default DRAM Burst Length The Choices 4 default 8 DRAM Queue Depth This item permits to place the depths of the memory The deeper the depth is the better is this function The Choices 4 level default 2 level 3 level DRAM Command Rate This item controls clock cycle that must occur between the last valid write operation and the next command The Choices 1T Command 2T Command default Write Recovery Time The Choices 3T default 2T tWTR for DDR400 ONLY The Choices 3T default 1T 2T 13 M7VIT Pro BIOS Setup AGP amp P2P Bridge Control If you highlight the literal Press Enter next to the AGP amp P2P Bridge Control label and then press the enter key it will take you a submenu with the following options AGP Aperture Size Select the size of the Accelerated Graphics Port AGP aperture The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The Choi
10. 3MHz CPU the DDR DIMM only support PC2700 DDR How to install a DIMM Module 1 The DIMM socket has a Plastic Safety Tab and the DIMM memory module has an Asymmetrical notch so the DIMM memory module can only fit into the slot in one direction 2 Push the tabs out Insert the DIMM memory modules into the socket at a 90 degree angle then push down vertically so that it will fit into the place 3 The Mounting Holes and plastic tabs should ft over the edge and hold the DIMM 5 Motherboard Description memory modules in place Jumpers Headers Connectors amp Slots Hard Disk Connectors IDE1 IDE2 The motherboard has a 32 bit Enhanced PCI IDE Controller that provides PIO Mode 0 4 Bus Master and Ultra DMA 33 66 100 133 functionality It has two HDD connectors IDE1 primary IDE2 secondary and DES The IDE connectors can connect a master and a slave drive soyou canconnect up to four hard disk drives The first hard drive should always be connected to IDE1 Floppy Disk Comector FDD1 The motherboard provides astandardfloppy disk connector tha supports 360K 720K 1 2M 1 44M and 2 88M floppy disk types This connedor supports the prov idedfloppy drive ribbon cables Accelerated Graphics Port Slot AGP1 8X Your monitor will attach directly to that video card This motherboard supports video cards for PCI slots but it is also equipped with an Accelerated Graphics Port AGP An AGP card will
11. 7VIT PrO ococonconcncononcononcnoncononcononnnncncanenennennnnenennennnnnnnnnena 3 CPU Installation vases scsi desc panai oietan roana edades 4 DDR DIMM Modules DIMM1 2 3 0c2ceeccecseeeceeeeesenenceeceaceunecesceanens 4 Jumpers Headers Connectors amp Slots 6 ESPANOL EE 11 Caracter sticas del M7VIT Pro us 11 Contenido del Paquete sens 12 Disposici n del M7VIT Pro usines 13 Instalaci n dela CPU occ E cate ence ee ee Ee due ENEE ca AE co etek cand E 14 Modulos DDR DIMM DIMM1 2 3 ccscecececsceseecececeneeseceaescaneseasenes 15 Puentes Cabezales Conectores y Ranuras 17 FRANCAIS caian dee clon dadas 22 M7VIT Pro Particularit s 0 ccccccecsnececeececececeseeceueaeneneeceanscunaeaseees 22 Dessin d M7VIT Pro ENNEN 24 WARPSPEEDER dese oie di edt cenciacdccecacucceccacadsdtuccdicdeceddavseacuas 25 APA IN E E E 5 EG ul E UE 5 Installation USAG oE e E ii EEA A E EEE A E ii TROUBLE SHOOTING ss naan a N 33 SOLUCION DE PROBLEMAG scccssecscnscecssnseasceeeeamseceseueesaneeseesens 34 Motherboard Description English M 7VIT Pro Features CPU Single AMD Socket Afor AMD Ahlon Duron Family processor Running at 200 266 333 MHz Front Side Bus Chipset North Bridge VIA KT400 A South Bridge VT8235 Main Memory Supports upto3 DDR device
12. In addition thefrequency status of CPU memory AGP and PCI along with the CPU speed are sy nchronically shown on our main panel Moreover to prdect users computer systens if the setting is not appropriate when testing and results in system fail or hang WarpSpeeder technology assures the sy stem stability by automdically rebooting the computer and then restart to a speed that is eitherthe original system speed or a Suitable one System Requirement OS Support Windows 98 SE Windows Me Windows 2000 Windows XP DirectX DirectX 81 or above The Windows XP operating system includes DirectX 8 1 If you use Windows XP you do not need to install DirectX 8 1 25 Motherboard Description Installation 1 Execute the setup execution file and then the following dialog will pop up Please click Next button andfollow the ddault procedure toinstall wei In thee ridad Wis ad foe lap precia Tha ra a all q ta a eds par a computa Tocor n cick Heel 2 When you see the following dialog in setup procedure it means setup is completed If the Launch the WarpSpeeder Tray Utility checkbox is checked the Tray Icon utility and WarpSpeeder utility will be automatically and immediately launched aftery ou click Finish button Basiai heed Wu fl reckig Eau bra wer pee on pos COMA F Lr Fa pS eet Tu Ur Motherboard Description Usage The folowing figures are just only for reference the scre
13. M7VIT Pro FCC Statement and Copyright This equipment has been tested andfound to comply wth the limits of aClass B digital dev ice pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful inteference in a residential installation This equipment generates uses and can radiate radio frequency energy and f not installed and used in accordance wih the instructions may cause hamful interference to radio communications There is no guarantee that interf erence will not occur in a particular installation The vendor makes no representations or warranties with resped to the contents here of andspecially disclaims any implied warranties of merchantability or fitness for any purpose Further the vendor reserves the right to revise this publication and to make changes to thecontents here of without obligation to notify any party bef orehand Duplication of this publication in pat or in whole is not allowed without first obtaining the vendor s approval in writing The contert of this user s is subject to be changed without notice and we will not be responsible for any mistakes found in this user s manual All the brand and product names are trademarks of theirrespective companies Contents A teg Sei E is clan De sed EE REES EE SE G t en s ee 1 M7VIT Pro Features cio dodge 1 Package Content oocococonconcnnononcononcamnnonencnnennnnencnnenennennnnrn ra nenennennanena 2 Layout Of M
14. Rat n LAN Opcional JPRNT1 JGAME1 Paralelo Puerto de Juego USB COMI COM2 Salidadel Entrada Entrada de Altavoz de Linea Mic Teclado E JCOMI JCOM2 21 Motherboard Description Francais M7VIT Pro Particularit s CPU Douille A AMD Simple pour AMD processeur de Famille Dirigeant a Autobus de C t de Front de MHz 200 266 333 Chipset Pont du Nord VIA Pont du Sud VT8235 M moire Principale Soutient dispositifs jusqu 3 DDR Soutient dispositifs de DDR SDRAM de 200 266 333 400MHz sans CEE La plus grande capacit de m moire sowenir est jusqu 3GB Fentes Cinqf entes demaitre dautobus PCI 32 bits a Unefente CNR Une fente AGP Abord IDE Soutient quatre IDE des lecteurs de disques Soutient PIO Mode 4 le Mode de Ma tre et DMA Ultra 33 66 100 133 le Mode de Maitre d Autobus Chip de r seau local VT6103 Vitesse Duelle 100 10 Mbps Audio AC97 2 2 interface PC99 la plainte Soutient 6 canaux bord P riph riques Soutient 360Ko 720Ko 1 2MB 1 44MB et 2 88MB des conducteurs de disquette Soutient 2 ports p riodiques Soutient 1 por parall le SPP EPP EC P mode Soutient le souris de PS 2 et le clavier de PS 2 Soutient 2 ports en arri re USB2 0 et 4 ports USB2 0 BIOS ACCORDENT k BIOS l gal 22 Motherboard Description Soutient APM1 2 Soutient ACPI Soutient la Fonction d USB Systeme
15. WS Write When enabled writes to the AGP bus are executed with zero wait states The Choices Enabled default Disabled PCH Post Write When Enabled CPU writes are allowed to post on the PCI bus The Choices Enabled default Disabled PCR Post Write When Enabled CPU writes are allowed to post on the AGP bus The Choices Enabled default Disabled VLink 8X Support The Choices Enabled default Disabled PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification The Choices Enabled default Disabled Memory Hole When enabled you can reserve an area of system memory for ISA adapter ROM When this area is reserved it cannot be cached Refer to the user documentation of the peripheral you are installing for more information The Choices Disabled default 15M 16M System BIOS Cacheable Selecting the Enabled option allows caching of the system BIOS ROM at F0000h FFFFFh which can improve system performance However any programs writing to this area of memory will cause conflicts and result in system errors The Choices Enabled Disabled default Video RAM Cacheable Enabling this option allows caching of the video RAM resultng m better system performance However if any program writes to this memory area a system error may result The Choices Enabled Disabled default 15
16. aciones pueden ser usados pero el arranque desde el disco r gido es imposible No puede arrancar despu s de instalar el segundo disco r gido Controle el cable de ejecuci n desde el discq hasta el disco del controlador Aseg rese dd que ambos lados est n enchufados co seguridad controle el tipo de disco en l4 configuraci nest ndar CMOS Copiando el disco r gido es extremadamentd importante Todos los discos r gidos so capaces de da arse en cualquier momento SOLUCI N Copie datos y documentos de aplicaci n Vuelva a fomatear el dsco r gido Vuelva instalar las aplicaciones y datos usando el Fije correctamente el puente masteresclavo Ejecute el programa SETUP y seleccione el tipo de disco correcto lame a ung d dsco para 34 27 02 2003 35 M7VIT Pro BIOS Setup BIOS SOU EE l Man Mea 3 2 Standard CMOS Features 02 065 ste een einer me it ni 6 3 Advanced BIOS R abueg gue cnrs Mets chier tte enter tisse st 9 4 Advanced Chipset Features 12 5 Integrated Peripherals rata interne seated does 16 6 Power Management Setup su 21 AG A ong ta el med ne etre 25 SPC Health Status tt Una een wate 28 9 Frequency Voltage Control ss 30 M7VIT Pro BIOS Setup BIOS Setup Introduction This manual discussed Award Setup program built into the ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in batter
17. al e Ground i 1 JCI1 Audio a JAUDIO 1 JCDINI JAUDIOI Front Audio Header JCDIN1 y ICE CD ROM Audio In Header Motherboard Description Pin Assignment Pin Assignment Mic n__ 2 Ground MicPower 4 Audio Power 5 RTLine Out 6 RTLine Out Reserved AE NC lo LFTLine Out LET Line Out is i RTLine In 12 RT Line In LFT LineIn 14 LFT Line In Pin 5 and 6 Pin9 and 10 Audio line out signals are routed Pinll and 12 to the back panel audio line out connector Pin13 and 14 No jumpers Audio line out and mic in signals are installed availablefor front panel audio connectors Digital Audio Connector JS PDIF1 o IO O II CON CCE CCC RR CCE CET bah X JSPDIFI s00 l D D ST A TC Lidd B Acer eee eee eee ey D ce Pe eee RN Motherboard Description Ckar CMOS Jumper JCMOS1 1 Pin 1 2 on gt Normal Operation default JCMOS1 Pin2 3 0n gt Clear CMOS Data Back Panel Connectors f JKBMSI JUSBLANI ee pee E PS 2 LAN Optional se Ge Game Port on i E ca o de eee a E Keyboard l q JCOMI JCOM2 F 10 Motherboard Description Espanol o Caracter sticas del M7VIT Pro UsaChipsets North Bridge VIA KT400 South Bridge VT8235 Winbond W83697HF y Lan Chip VT6108 Contiene facilidades WO integrados en la placa madre en el que incluye dos puertos en serie un puerto paralelo un puertos de rat n PS 2 un
18. ames Contacto 1 2 5 6 gt 100 Mhz i Contacto 2 3 5 6 gt 133 Mhz SE 3 default _JCLKI Contacto 2 3 4 5 gt 166Mhz Subsistema de Audio JAUDIO1 JCDIN1 Up JAUDIO1 S ale Cabezal Frontal de Audio 13 38 14 JCDINI eoao Cabezal de Entrada de Audio q CD ROM A RITO 19 Motherboard Description JAUDIO1 Contactos Asignaci n Contactos Asignaci n 1 Entrada del MIC 2 Tierra 13 CorientedelMIC 4 Corriente de Audio RT Salida de Linea e RT Salidade Linea EE AA Ee ESA 9 LFT Salida de Linea 10 LFT Salida deL nea 1 RT Entrada de Linea 12 RTEntrada de Lineal 13 LEFT Entada de Lineal 14 LFTEntrada de L nea Contacto 5 amp 6 La se al de salida de linea del Audio Contacto9 810 encamina al conector delasalidade linea Contacto 11 amp 12 del Audio ubicado en el panel trasero Contacto 13 amp 14 La se al desalidade linea del Audio y la se al del entrada del mic estan disponibles desde el conectorde A udio del panel frontal No jumpers installed Puente de Borrar CMOS JCMOS1 i 1 Contacto 1 2 on gt Operaci n Normal default Contacto 2 3 on gt Borrar Datos CMOS JCMOSI k ad 20 Motherboard Description Conector Digital de Audio JSPDIF1 II O II eres P D JSPDIFI eog T i2 at Fait III A RIIT II RER II IR RSR EIN 1 be Conectores del Panel Trasero OU CTT JKBMS1 JUSBLANI
19. board Description 3 Voltage Panel Click the Voltage button in Main Panel the button will be highlighted and the Voltage Panel will slide ou to up as thefollowing figure In this panel you can decide to increase CPU core voltage and Memory voltage or not The default setting is No If you want to get the best performance of overclocking we recommend y ou click the option Y es nia VE ball bed 2 8 GPU SPEED 5 A 4 Overclock Panel Click the Ov erclock button in Main Panel the button will be highlighted and the Overclock Panel will slide ou to left as the following figure 29 Motherboard Description Overclock Panel contains the these features a 3MHz button 1MHz button 1MHz buton and 3MHz button provide user the ability to doreal time overclock adjustment b Warning Manually overclock is potentially dangerous o especially when the overclocking percentage is over 110 We strongly recommend you verify every speed you overclock by click the Verify button Or you can just click Auto overclock button and let WarpSpeeder automatically gets the best result for you b Recovery Dialog button Pop up the following dialog Let user select a restoring way if system need to do afail safe reboot Please select a recovery option that will decide what kind of restoring you want to do after system fail safe reboot Optio
20. board LAN Boot ROM This item allows you to enable or disable Onboard LAN Boot ROM The Choices Disabled default Enabled Super IO Device If you highlight the literal Press Enter next to the Super IO Device label and then press the enter key it will take you a submenu with the following options Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you wish to use it If install and FDC or the system has no floppy drive select Disabled in this field The Choices Enabled default Disabled 17 M7VIT Pro BIOS Setup Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports The Choices Disabled 3F8 1RQ4 default 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Auto Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports The Choices Disabled 2F8 IRQ3 default 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 Auto UART Mode Select This item allows you to determine which Infra Red IR function of onboard I O chip The Choices Normal default AS KIR IrDA RxD TxD Active This item allows you to determine which Infrared IR function of onboard I O chip The Choices Hi Lo default Hi Hi Lo Hi Lo Lo IR Trans mission Delay This item allows you to enable disable IR transmission delay The Choices Enabled default Disabled UR2 Duplex Mod
21. ces 64M 256M 128M default 32M 16M 8M 4M AGP Mode This item allows you to select the AGP Mode The Choices 4X default 2X 1X AGP Driving Control By choosing Auto the system BIOS will the AGP output Buffer Drive strength P Ctrl by AGP Card By choosing Manual it allows user to set AGP output Buffer Drive strength P Ctrl by manual The Choices Auto default Manual AGP Driving Value While AGP driving control item set to Manual it allows user to set AGP driving The Choices DA default AGP Fast Write The Choices Enabled Disabled default AGP Master 1 WS Write When Enabled writes to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled AGP Master 1 WS Read When Enabled read to the AGP Accelerated Graphics Port are executed with one wait states The Choices Disabled default Enabled AGP 3 0 Calibration cycle This item allows you to enable or disable AGP 3 0 Calibration cycle The Choices Enabled Default Disabled 14 M7VIT Pro BIOS Setup CPU amp PCI Bus Control If you highlight the literal Press Enter next to the CPU amp PCI Bus Control label and then press the enter key it will take you a submenu with the following options PCI Master 0 WS Write When enabled writes to the PCI bus are executed with zero wait states The Choices Enabled default Disabled PCD Master 0
22. de Fonctionnement Offre lex cution perf omance la plus haute pour MS DOS Windows 2000 des Fen tres Moi Windows XP SCO UNIXetc Dimensions ATX Forment le Facteur 30 5cm X 20 0cm W X L 23 Motherboard Description Dessin d M7VIT Pro TTT JUSBV I lt D 4 o n AGP SLOT PCII PCISLOT xl 6 CT iE PCI2 BE PCISLOT J USB2 PCI3 PCISLOT E 10 pcia EA inbond PCI SLOT 227 USB V2 1 0 DE JPANELI MAPA H 3 JSFANI 24 Motherboard Description WarpSpeeder e Introduction A WarpSpeeder a new power ul control utility features three userfriendly functions including Ov erclok Manager Ov ervoltage Manager and Hardware Monitor The following three sections detail the installation of FastTrak 376 drivers on a system that has Windows 98 Me already installed If you re installing the FastTrak 376 drvers on a system during a Windows 98 Me installation see Installing Drivers During Windows 98 Me Installation on page 10 With the Overclock Manager users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click The Overvoltage Manager on the other hand helps to power up CPU core voltage and Memory voltage The cool Hardware Monitor smartly indicates the temperatures voltage and CPU fan speed as well as the chipset iformation Also inthe About panel you can get detail descriptions about BIOS model and chipsets
23. e Select the value required by the IR device connected to the IR port Full duplex mode permits simultaneous two direction transmission Half duplex mode permits transmission in one direction only at a time The Choices Half default Full Use IR Pins Consult your IR peripheral documentation to select the correct setting of the TxD and RxD signals The Choices IR Rx2Tx2 default RxD2 TxD2 Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O Address The Choices 378 IRQ7 default 278 IRQ5 3BC IRQ7 Disabled Parallel Port Mode The default value is SPP The Choices SPP default Using Parallel port as Standard Printer Port EPP Using Parallel Port as Enhanced Parallel Port ECP Using Parallel port as Extended Capabilities Port 18 M7VIT Pro BIOS Setup ECP EPP Using Parallel port as ECP amp EPP mode EPP Mode Select Select EPP port type 1 7 or 1 9 The Choices EPP 1 7 default EPP 1 9 ECP Mode Use DMA Select a DMA Channel for the port The Choices 3 default 1 Game Port Address Game Port I O Address The Choices 201 default 209 Disabled Midi Port Address Midi Port Base I O Address The Choices 330 default 300 290 Disabled Midi Port IRQ This determines the IRQ in which the Midi Port can use The Choices 5 10 default Init Display First With systems that have multiple video cards this option determ
24. e Hardware Monitor panel will slide ou to left as the following figure In this panel you can get the real time status information of y our system The information will be rdreshed every 1 second Motherboard Description 6 Abou Panel Click the About button in Main Panel the buton will be highlighted and the About Panel will slide out to up as the following f igure In this panel youcan get model name and detail information in hints of all the chipset that are related to overclocking You can also get the mainboard s BIOS model and the Version number d WarpSpeeder utility WarpSpeeder Hat SA Les ah Lib lares Drey Didi D wran a Note Becaus th overclock overvoltage and hardware monitor features are controlled by several separate chipset WarpSpeeder divide these features to separate panels If one chipset is not on board the correlative button in Main panel will be disabled but will not interfere other panels functions This property can make WarpSpeeder utility more robust Motherboard Description Trouble Shooting Contact techrical support PROBABLE SOLUTION System inoperative Keyboard lights are on Using even pressure on both ends of thd power indicator Ights are lit hard drive is DIMM press down firmly until the moduld spinning snaps into place PROBABLE SOLUTION System does not boot from hard disk drive can Check cable running from dis
25. e Choices Disabled default 1 Min 2 Min 3 Min 4 Min 5 Min 6 Min 7 Min 8 Min 9 Min 10 Min 11 Min 12 Min 13 Min 14 Min 15Min Suspend Mode The item allows you to select the suspend type under ACPI operating system The Choices Disabled default 1 Min 2 Min 4 Min 6 Min 8 Min 10 Min 20 Min 30 Min 40 Min 1 Hour Video Off Option This field determines when to activate the video off feature for monitor power management The Choices Suspend Off default Always on Video Off Method This option determines the manner in which the monitor is goes blank V H SYNC Blank default This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen 22 M7VIT Pro BIOS Setup This option only writes blanks to the video buffer DPMS Initial display power management signaling The Choices Stop Grant PwrOn Suspend Modem Use IRQ This determines the IRQ which can be applied in MODEM use The Choices 3 default 4 5 7 9 10 11 NA Run VGABIOS if S3 Resume Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state The system time is shortened if you disable the function but system will need AGP driver to initialize the card So if the AGP driver of the VGA card does not support the initialization feature the display may work abnormally or not function
26. ed Disable cache CPU L2 Cache ECC Checking This item allows you to enable disable CPU L2 Cache ECC Checking The Choices Enabled default Disabled Video BIOS Shadow Determines whether video BIOS will be copied to RAM for faster execution Enabled default Optional ROM is enabled Disabled Optional ROM is disabled Virus Warning This option allows you to choose the Virus Warning feature that is used to protect the IDE Hard Disk boot sector If this function is enabled and an attempt is made to write to the boot sector BIOS will display a warning message on the screen and sound an alarm beep Disabled default Virus protection is disabled Enabled Virus protection is activated Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self Test POST to execute after you power up the computer Enabled default Enable quick POST Disabled Normal POST Boot Up NumLock Status Selects the NumLock State after power on On default Numpad is number keys Off Numpad is arrow keys Gate A20 Option Select if chipset or keyboard controller should control Gate A20 Normal A pin in the keyboard controller 10 M7VIT Pro BIOS Setup controls Gate A20 Fast default Lets chipset control Gate A20 Typematic Rate Settin When a key is held down the keystroke will repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be
27. elp 9 Previous Values ptimized Defaults CPU Clock This item allows you to select CPU Clock and CPU over clocking If unfortunately the system s frequency that you are selected is A not functioning there are two methods of booting up the system Method 1 Clear the COMS data by setting the JCOMS1 2 3 closed as ON status All the CMOS data will be loaded as defaults setting Press the lt Insert gt key and Power button simultaneously after that keep on pressing the lt Insert gt key until the power on screen showed This action will boot up the system according to FSB of the processor X It s strongly recommended to set CPU Vcore and clock in default setting If the CPU Vcore and clock are not in default setting it may cause CPU or M B damage Method 2 30
28. en printal in this user manual will change accordingto your motherboard on hand WarpSpeeder includes 1 tray icon and 5 pane 1 Tray Icon Whenever the Tray Icon utility is launched it will display a littletray icon onthe right side of Windows Taskbar This utility is responsible for conv eniently invoking WarpSpeeder Utility Youcan use the mouse by clicking the left button in order to invoke WarpSpeederTM directly from the little tray icon or you can rightclick the little tray icon to pop up a popup menu as following figure The Launch Utility item inthe popup menu has the same furction as mouse l t click on tray icon and Exit item will close Tray Icon utility if selected 2 Main Panel If you click the tray icon WarpSpeeder utility wil be invoked Please refer do the following figure the utility s first window y ou will see is Main Panel Main Panel contains features as follows a Display the CPU Speed CPU external clock Memory clock AGP clock and PCI 27 Motherboard Description clock information b Contains About Voltage Overclock and Hardware Monitor Buttons for invoking respective panels c With a userfriendy Status Animation it can represent 3 overclock percentage stages Man walking gt overclock percentagefrom 100 110 Panther running gt overclock percentage from 110 120 Car racing gt overclock percentagefrom 120 above 28 Mother
29. et the system internal clock IDE Primary Master Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options IDE Primary Slave Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options IDE Secondary Master Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options IDE Secondary Slave Options are in its sub Press lt Enter gt to enter the menu sub menu of detailed options Drive A 360K 5 25 in Select the type of floppy Drive B 1 2M 5 25 in disk drive installed in your i system 720K 3 5 in 1 44M 3 5 in 2 88M 3 5 in None Video EGA VGA Select the default video CGA 40 device CGA 80 MONO M7VIT Pro BIOS Setup Item Options Description Halt On All Errors Select the situation in which No Errors you want the BIOS to stop Base Memory All but Keyboard All but Diskette All but Disk Key N A the POST process and notify you Displays the amount of conventional memory detected during boot up Extended Memory N A Displays the amount of extended memory detected during boot up Total Memory N A Displays the total memory available in the system M7VIT Pro BIOS Setup 3 Advanced BIOS Features m Figure 3 Advanced BIOS Setup gt Boot Seq amp Floppy Setup Press Enter Item Help Cache amp Shadow Setup Press Enter
30. fault Enabled Wake Up On LAN Ring To use this function you need a LAN add on card which support power on function It should also support the wake up on LAN jump Disabled default Wake up on LAN Ring not supported Enabled Wake up on LAN Ring supported RTC Alarm Resume When Enabled you can set the date and time at which the RTC real time clock alarm awakens the system from Suspend mode The Choices Enabled Disabled default IRQs Activity Monitoring Press Enter to access another sub menu used to configure the different wake up events i e wake on LPT amp COMM activity Primary INTR On IRQ3 COM2 Enabled IRQ4 COM1 Enabled IRQS LPT2 Enabled IRQ6 Floppy Disk Enabled IRQ7 LPT 1 Enabled IRQ8 RTC Alarm Disabled IRQ9 IRQ2 Redir Disabled IRQ10 Reserved Disabled IRQ11 Reserved Disabled IRQ12 PS 2 Mouse Enabled IRQ13 Coprocessor Enabled IRQ14 Hard Disk Enabled IRQ15 Reserved Disabled 24 M7VIT Pro BIOS Setup 7 PnP PCI Configurations This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings m Figure 7 PnP PCI Configurations 0 0
31. habr completado su instalaci n CPU Cabezales del Sistema de Ventilaci n JCFANI JSFAN1 A A A O ae RARE ee MENS NARs EERE Sener nt ERC N a 12V E Tierra Sense Tierra i DE Sense i E i 1 JCFAN1 i SE e WEE EES ur A 14 Motherboard Description M dulos DDR DIMM DIMM1 2 3 DRAM Tiempo de Acceso 2 5V Unbuffered Registered DDR PC1600 2100 2700 3200 Tipo requerido DRAM Tipo 64MB 128MB 256MB 512MB 1GB M dulo DIMM 184 contactos Localizacion Modulo DDR Total del del Modulo Tama o de DIMM e DIMM 1 es 4 64MB 128MB 256MB 512MB 1GB 1 64MB 128MB 256MB 512MB 1GB 4 e La lista de arriba para la configuraci n DRAM es solamente para referencia Listado del estadodd DDR400 N mero de Serie Tama o Chip del M dulo 1 DDR400 KINGMAX KDL684T4AA50 Doble Pass Cara 256M x2 2 DDR400 SAMSUNG K4H560838D TCC4 Una Cara Pass 256M x3 ora MB Maximo de 3GB 3 DDR400 TwinMO S TMD 7608F 8E50B Una Cara Pass 256M x3 4 DDR400 Winbond W942508BH 5 Una Cara Pass 256M x3 5 DDR400 Winbond W942508BH 5 Doble Pass Cara 512M x3 e Siusa FSB 333MHz CPU DDR DIMM solamente soporta PC2700 DDR 15 Motherboard Description C mo instalar un M dulo DIMM 1 El z calo DIMM tiene una leng eta pl stica de seguridad y el m dulo de memoria DIMM tiene una muesca asim trica as el m dulo de memoria DIMM puede caber solamente en la ranura de una s
32. ines whether the primary display uses a PCI Slot or an AGP Slot The Choices PCI Slot default AGP OnChip USB Controller This option should be enabled if your system has a USB installed on the system board You will need to disable this feature if you add a higher performance controller The Choices All Enabled default All Disabled 1 amp 2 USB Port 2 amp 3 USB Port 1 amp 3 USB Port 1 USB Port 2 USB Port 3 USB Port USB Keyboard Support Enables support for USB attached keyboards The Choices Disabled default Enabled USB Mouse Support Enables support for USB attached mouse The Choices Disabled default Enabled IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write 19 M7VIT Pro BIOS Setup If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block mode most new drives do select Enabled for automatic detection of the optimal number of block read write per sector where the drive can support The Choices Enabled default Disabled 20 M7VIT Pro BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up power down features H Figure 6 Power Management Setup ACPI function Enabled Item Help ACPI Suspend Type S1 P0S 1 Power Management Option User
33. k to dis be booted from CD ROM drive controller board Make sure both ends are securely plugged in check the drive type in the standard CMOS setup Backing up the hard drive is extremel important Al hard dsks are capable o PROBABLE System only boots from CD ROM Hard disk can Back up data and applications files Reforma be read and applications can be used but the hard dive Re install applications and booting from hard disk is impossible data using backup disks PROBABLE SOLUTION Screen message says Invalid Configuration on Review system s equipment Make sure CMOS Failure correct information is in setup PROBABLE SOLUTION Cannot boot system after installing secord hard Set master slave jumperscorrectly Gig Run SETUP program and select correct drive tyes Cal drive manufacturers fo 33 Soluci n de Problemas AUSA PROB ABLE No hay corriente en el sistema La luz de corriente no ilumina ventilador dentro de la uente de alimentaci n apagada Indicador de luz del teclado apagado Sistema inoperativo Luz del teclado encendido luz de indcador de corriente iluminado disco Aseg rese que el cable de transmisi n estq seguramente enchufado Reemplace e cable CAUSA PROBABLE SOLUCION Sistema no arranca desde el disco r gido puede ser arrancado desde el CD ROM drive CAUSA PROB ABLE Sistema solamente arranca desde el CD ROM Disco r gido puede leer y aplic
34. ning Shutdown Temperature Disabled Show HAN Monitor in POST Enabled Chassis Open Warnning Disabled fl e Move Enter Select PU PD Value F1 Save ESC Exit F1 General Help F5 Previous Values F Optimized Defaults Current CPU1 Temperature This field displays the current temperature of the CPU Current CPUFAN Speed This field displays the current speed of CPU fan Current SYSFAN Speed This field displays the current speed SYSTEM fan CPU Veore 3 3V 5V 12V 12V 5V VBAT V 5VSB V Detect the system s voltage status automatically Shutdown Temperature This item allows you to set up the CPU shutdown Temperature This item only effective under Windows 98 ACPI mode The Choices Disabled default 60 C 140 F 65 C 149 F 70 C 158 F 75 C 167 F 28 M7VIT Pro BIOS Setup Show H W Monitor in POST If your computer contains a monitoring system it will show PC health status during POST stage The item offers several delay time for you to choose The Choices Enabled default Disabled Chassis Open Warning This item allows you to enable or disable Chassis Open Warning beep The Choices Disabled Default Enabled 29 M7VIT Pro BIOS Setup 9 Frequency Voltage Control m Figure 9 Frequency Voltage Control Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control Menu Level e Tl Move BEE PU PD Value TIR ESC Exit F1 General H
35. ns Group Restore to Hardware Default CPU Clock Value c Auto overclock button User can click this button and WarpSpeeder will set the best and stable performance andfrequency automatically WarpSpeeder utility will execute a series of testing until system fail Then system will dof ail saf e reboot by using Watchdog function After reboot the WarpSpeeder uility will restore to the hardware d ault setting or load the verified best and stable frequency accordingto the Recovery Dialoge setting d Verify button User can click this button and WarpSpeeder will proceed a testingf or current frequency If the testing is ok then the current f requeng will be sa ed into system registry If the testing fail system wil do a fail safe rebooting After rebod the WarpSpeeder utility wll restore to the hardware default setting or load the verified best and stable frequency according to the Recovery Dialog s setting 30 Motherboard Description Note Because the testingprograms invoked in Auto overclock and Verify include DirectDraw Direct3D and DirectShow tests the DirectX 8 1 or newer runtime library is required And please make sure your display card s color depth is High color 16 bit or True color 24 32 bit that is required for Direct3D rendering E 100 Y 5 Hardware Monitor Panel Click the Hardware Monitor button in Main Panel the button will be highlighted and th
36. o Disabled The Choices Enabled default Disabled 16 M7VIT Pro BIOS Setup IDE Primary Secondary Master Slave PIO The IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the IDE devices that the onboard IDE interface supports Modes 0 through 4 provides successively increased performance In Auto mode the system automatically determines the best mode for each device The Choices Auto default Mode Model Mode2 Mode3 Mode4 IDE Primary Secondary Master Slave UDMA Ultra DMA 100 functionality can be implemented if it is supported by the IDE hard drives in your system As well your operating environment requires a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software both support Ultra DMA 100 select Auto to enable BIOS support The Choices Auto default Disabled VIA OnChip PCI Device If you highlight the literal Press Enter next to the OnChip PCI Device label and then press the enter key it will take you a submenu with the following options VIA 3058 AC97 Audio This option allows you to control the onboard AC97 audio The Choices Auto default Disabled VIA 3068 MC97 Modem This option allows you to control the onboard MC97 modem The Choices Auto default Disabled VIA 3043 OnChip LAN This option allows you to control the onboard LAN The Choices Enabled default Disabled On
37. o change them Enter Password Save amp Exit Setup Save all configuration changes to CMOS memory and exit setup Confirmation message will be displayed before proceeding SAVE to CHOS and EXIT Y N Exit Without Saving Abandon all changes made during the current session and exit setup confirmation message will be displayed before proceeding Quit Without Saving Y N N Upgrade BIOS This submenu allows you to upgrade bios BIOS UPDATE UTILITY Y N N M7VIT Pro BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item Figure 2 Standard CMOS Setup Date mm dd yy Jan 3 2003 Time hh mm ss EIA IDE Primary Master IDE Primary Slave IDE Secondary Master IDE Secondary Slave Drive A 1 44M 3 5 in Drive B None Video EGAZYGA Halt On All But Keyboard Menu Level L Change the day year and century month M7VIT Pro BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu Item Options Description Date mm dd yy Set the system date Note that the Day automatically changes when you set the date Time hh mm ss S
38. om CMOS F6 key Load the fail safe defaults from BIOS default table F7 key Load the optimized defaults F10 key Save all the CMOS changes and exit M7VIT Pro BIOS Setup 1 Main Menu Once you enter Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu 1 WARNING The information about BIOS defaults on manual Figure 1 2 3 4 5 6 7 8 9 is just for reference please refer to the BIOS installed on board for update information Figure 1 Main Menu Standard CHOS Features Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status Upgrade BIOS Esc Quit F9 Menu in BIOS E Select Item F10 Save amp Exit Setup Time Date Hard Disk Type Standard CMOS Features This submenu contains industry standard configurable options Advanced BIOS Features This submenu allows you to configure enhanced features of the BIOS Advanced Chipset Features This submenu allows you to configure special chipset features M7VIT Pro BIOS Setup Integrated Peripherals This submenu allows
39. ower management and device configuration capabilities as defined in the ACPI specification developed by Microsoft Intel and Toshiba M7VIT Pro BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2 1 of the Intel PCI Peripheral Component Interconnect local bus specification DRAM Support DDR SDRAM Double Data Rate Synchronous DRAM are supported Supported CPUs This AWARD BIOS supports the AMD CPU Using Setup In general you use the arrow keys to highlight items press lt Enter gt to select use the lt PgUp gt and lt PgDn gt keys to change entries press lt F1 gt for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program by using the keyboard Keystroke Function Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item on the left menu bar Right arrow Move to the item on the right menu bar Move Enter Move to the item you desired PgUp key Increase the numeric value or make changes PgDnkey Decrease the numeric value or make changes Key Increase the numeric value or make changes Key Decrease the numeric value or make changes Esc key Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit Current page and return to Main Menu F1 key General help on Setup navigation keys F5 key Load previous values fr
40. puerto de teclado PS 2 puertos de audio puertos USBy un puerto de juego Soporta Single Socket A para procesadores de la familia AMD Athlor Duron corriendo a 200 266 333 MHz frecuencia Front Side Bus El sistema bus AMD Ahlon Duron soporta una alta v elocidad de 200 266 333 MHz splittransaction AMD Athlor Duron sistemas de interface bus Soporta Ultra DMA 33 66 100 133 Bus Modos Master PIO Modo 4 Modo Master y alta perf omancia del disco duro Soporta USB2 0 6 puertos Dispositivo High Speed 2 puertos en elpaneltraseroy 4 puertos en el panelf rontal El sistema controlador KT400 est dise ado para sopotar 200 266 333 400 MHz DDR SDRAMDIMMs Soporta tama o de memoria m xima de hasta 3GB Soporta una ranura CNR solamente de Tipo B una ranura AGP 4X y cinco ranuras 32 bit PCI Bus Conforma conlas especificaciones delf actor de forma de tama o PC ATX Soporta sistemas operativos populares tales cano Windows NT Windows 98SE Windows 2000 Windows ME Windows XP y LINUX Protecci n contra el exceso detemperatura de la CPU Intel AC 97 2 2 compatible High S N ratio reune los requisitos del PC 99 Entrada de L nea y Entrada del Mic compartido con el Audio trasero con untotal de 6 canales de Audio 6 Canales AC97 Codec Cambiando la Entrada de L nea por la Salida del Audio Trasero y la Entrada del MIC por la salida Bass Center a trav s de la utilidad del audio Soporta funciones delcabezal de Audio Fron
41. s Supports 200 266 333 400MHz without ECC DDR SDRAM devices The largest memory capacity isupto 3GB Slots Five 32 bit PCI bus master slots One CNR slot One AGP slot On Board IDE Supports fouriDE disk drives Supports PIO Mode 4 Master Mode and Ultra DMA 33 66 100 133 Bus Master Mode LAN Chip VT6103 Dual Speed 100 10 Mbps Audio AC97 2 2 interface PC99 complaint Supports 6 channels On Board Peripherals Supports 360K 720K 1 2MB 1 44MB and 2 88MBfloppy disk driv ers Supports 2 serial ports Supports 1 parallel port SPP EPP ECP mode Supports PS 2mouse and PS 2key board Supports 2 back USB2 0 ports and 4 front USB2 0 ports BIOS AWARD legal Bios Supports APM1 2 Supports ACPI Motherboard Description Supports USB Function Operating System Offers the highest perfomancefor MS DOS Windows 2000 Windows Me Windows XP SCO UNIX etc Dimensions ATXForm Fador 30 5 amp m X 20 0cm W XL Package contents HDD Cable X1 FDD Cable X1 Fully Setup Driver CD X1 Flash Memory Writer f or BIOS update X 1 USB Cable X2 Optional Rear I O Panelfor ATXCase X1 Optional Motherboard Description Layout of M7VIT Pro Sm Em KBV JUSBV 1 lt D O gt Q N TAN JATXP WRI KT400 MMVI GAME Port 131 1 4 ADTI AGP SLOT MAN PCI PCISLOT 1 Ji vi pcr WEB En PCISLOT J USB2 PCI3 Wa PCISLOT
42. take advantage of AGP technology for improved video efficiency and perfomance especially with 3D graphics Communication Network Riser Slot CNR1 The CNR specification is an open Industry Standard Architecture and it defines a hardware scalable riser cardinterface which supports audio network andmodem only Peripheral Component Interconnect Slots PCI1 5 This motherboard is equipped with 5 standard PCI slots PCI stands f or Peripheral Component Interconnect and it is a bus standardfor expansioncards which has supplanted the older ISA bus standard in most ports This PCI slot is designated as 32 bits Motherboard Description JATXPWRI E ATX Power Conn LEES EECH Bie e PO E EN Een O idl Pin Assignment Pin Assignment E A PE A 118000 ES El E 4 DaO 5 Data 6 Data JUSB2 3 7 Ground 8 Ground EOS E FO JUSBVI 2 JKBVI b 1 1 Pin 1 2 on gt 5V For Normal Function Pin 2 3 on gt 5V_SB For S3 Wake up Function EN Motherboard Description Front Panel OE Or JPANELI SPK gt Speaker Conn E HLED gt Hard Driver LED E RST gt Reset Button R gt Infrared Conn i SLP gt Sleep Button PWR_LED gt Power LED ONT OFF gt Power on Button J O S 6 Pin1 2 5 6 gt 100Mhz WA Pin 2 3 5 6 gt 133Mhz ed 3 default JCLKI Pin 2 3 4 5 gt 166Mhz Case Open Connector ICH P Case Open Sign
43. tal Soporta funciones SPDIF Out Lan Chip VT6103 Fast EtherNet 10 100 1 Puerto PHY Transceiver Opcional 11 Motherboard Description OG OG GG GG XA XA XA x Doble velocidad 100 10Mbps Half and Full Duplex MII Interface al Controlador Ethernet Auto Negociaci n 10 100 Full Half Duplex Conf orma con todas las aplicaciones IEEE 802 3 10 Base T y 100 Base Tx Estandar Baseline Wander Correction Contenido del Paquete Cable HDD X1 Cable FDD X1 Configuraci n completa del Driver CD X1 Flash Memoy Writer para actualizaci n del BIOS X 1 Cable USB X2 Opcional Panel Trasero I O para Caja ATX X 1 Opcional 12 Motherboard Description Disposici n del M7VIT Pro mmm kB VI JU SBV1 SocketA C H KT400 JAUDIOI eer SH BLAN Chip Lo o O 1 vn ISS PCI AL D 4 E E PCI2 LC deal rc ERA IDE 1 ID E2 19 ia JUS B3 ccs RW 1 0 JW OL1 JPANEL 1 Da ges H H JSFANI 13 Motherboard Description Instalaci n de la CPU 1 Tire de la palanca del lado del z calo luego levante la palanca hasta un ngulo de 90 grados 2 Sit e el contacto A del z calo y busque el punto blanco o corte el borde en la CPU Empareje el contacto A con el punto blanco corte del borde luego inserte la CPU 3 Presione la palanca para abajo Ponga el ventilador en la CPU y abr chelo Luego ponga el puerto de corriente del ventilador en el JCFAN1 Y ya
44. ura de la Banda de Suspersi n de Comunicaci n y Red CNR1 La especificaci n CNR es una abierta Industria de Arquitectura Est ndar que define una tarjeta de interface escalable del hardware en el que soporta audio y modem Ranura de Interconexi n del Componente Perif rico PCI1 5 Esta placa madre est equipada con 5 ranuras est ndar PCI PCI es la sigla para Interconexi n del Componente Perif rico y es un bus est ndar para tarjetas de expansi n en el quesuplantaa la antigua bus est ndar ISA en su mayor a de las partes Esta ranuraPCl est dise adocon 32 bits Conector de Corriente JATXPWR1 JATXPWRI Conector de Corriente AT X Motherboard Description Cabezal Wake On LAN J WOLI Tierra Wake up SV_SB iS 5V 5 VSB Selecci n para US B KB JUS BV1 2 JKBV1 JUSBV1 2 JKBV 1 Ve vi Contacto 1 2 on gt 5V Para Funcion Normal Se Contacto 2 3 on gt 5V_SB Para Funcion S3 Wake up F Conector Case Open KH Se al Case Open Tierra 1 CI 18 Motherboard Description Conector del Panel Frontal JPANEL1 O menntenannnn mennaan Ehe PWR_LED ofo o H 2 1 i sek YO RST HLED i SPK gt Conector de Altavoz E HLED gt LED del Disco Duro E i RST gt Bot n de Reinicio q IR gt Conector Infrarojo E SLP gt Bot n de Suspensi n E PWR_LED gt Corriente LED ON OFF gt Bot n de Encendido Seecci n del Reloj del CPU JCLK1 E
45. urce is assigned to the ISA Bus and provides non PnP ISA add on cards PCI ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add on cards and peripherals The Choices Disabled default Enabled Resources Controlled By By Choosing Auto ESCD default the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral By Choosing Manual the user will need to assign IRQ amp DMA for add on cards Be sure that there are no IRQ DMA and I O port conflicts IR Resources This submenu will allow you to assign each system interrupt a type depending on the type of device using the interrupt When you press the Press Enter tag you will be directed to a submenu that will allow you to configure the system interrupts This is only configurable when Resources Controlled By is set to Manual IRQ 3 assigned to PCI Device IRQ4 assigned to PCI Device IRQ 5 assigned to PCI Device IRQ 7 assigned to PCI Device IRQ 9 assigned to PCI Device IRQ 10 assigned to PCI Device IRQ 11 assigned to PCI Device IRQ 12 assigned to PCI Device IRQ 14 assigned to PCI Device IRQ 15 assigned to PCI Device PCI VGA Palette Snoop Choose Disabled or Enabled Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility Ho
46. wever the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors and the graphic controller needs to know what is in the palette of the VGA controller To do this the non VGA graphic controller watches for the Write access to the VGA palette and registers the snoop data In PCI based systems where the VGA controller is on the PCI bus and a non VGA graphic controller is on an ISA bus the Write Access to the palette will not show up on the ISA bus if the PCI VGA controller responds to the Write 26 M7VIT Pro BIOS Setup In this case the PCI VGA controller should not respond to the Write it should only snoop the data and permit the access to be forwarded to the ISA bus The non VGA ISA graphic controller can then snoop the data on the ISA bus Unless you have the above situation you should disable this option Disabled default Disables the function Enabled Enables the function Assign IRQ For VGA This item allows the users to choose which IRQ to assign for the VGA The Choices Enabled default Disabled Assign IR For USB This item allows the users to choose which IRQ to assign for the USB The Choices Enabled default Disabled 27 M7VIT Pro BIOS Setup 8 PC Health Status m Figure 8 PC Health Status Phoenix AwardBIOS CMOS Setup Utility PC Health Status Item Help Menu Level Enable Disabl Open Harn
47. y backed RAM so that it retains the Setup information when the power is tumed off The Award BIOS installed in your computer system s ROM Read Only Memory is a custom version of an industry standard BIOS This means that it supports Intel Pentium 4 processor input output system The BIOS provides critical low level support for standard devices such as disk drives and serial and parallel ports Adding important has customized the Award BIOS but nonstandard features such as virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system The rest of this manual is intended to guide you through the process of configuring your system using Setup Plug and Play Support These AWARD BIOS supports the Plug and Play Version 1 0A specification ESCD Extended System Configuration Data write is supported EPA Green PC Support This AWARD BIOS supports Version 1 03 of the EPA Green PC specification APM Support These AWARD BIOS supports Version 1 1 amp 1 2 of the Advanced Power Management APM specification Power management features are implemented via the System Management Interrupt SMI Sleep and Suspend power management modes are supported Power to the hard disk drives and video monitors can be managed by this AWARD BIOS ACPI Support Award ACPI BIOS support Version 1 0 of Advanced Configuration and Power interface specification ACPI It provides ASL code for p
48. you to configure certain IDE hard drive options and Programmed Input Output features Power Management Setup This submenu allows you to configure the power management features PnP PCI Configurations This submenu allows you to configure certain Plug and Play and PCI options PC Health Status This submenu allows you to monitor the hardware of your system Frequency Voltage Control This submenu allows you to change CPU Vcore Voltage and CPU PCI clock However this function is strongly recommended not to use Not properly change the voltage and clock may cause CPU or M B damage Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence These configurations are factory settings optimized for this system A confirmation message will be displayed before defaults are set Load Optimized Defaults Y N Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility You will be prompted with to enter a password Enter Password M7VIT Pro BIOS Setup Set User Password If the Supervisor Password is not set then the User Password will function in the same way as the Supervisor Password If the Supervisor Password is set and the User Password is set the User will only be able to view configurations but will not be able t
49. ystem memory resources such as DRAM It also coordinates communications with the PCI bus The default settings that came with your system have been optimized and therefore should not be changed unless you are suspicious that the settings have been changed incorrectly m Figure 4 Advanced Chipset Setup DRAM Clock Drive Control AGP amp P2P Bridge Control CPU amp PCI Bus Control Memory Hole System BIOS Cacheable Video RAM Cacheable Press Enter Press Enter Press Enter Disabled Disabled Disabled Menu Level gt DRAM Clock Drive Control To control the Clock Drive If you highlight the literal Press Enter next to the DRAM Clock Drive Control label and then press the enter key it will take you a submenu with the following options DRAM Clock This item determines DRAM clock following 100MHz 133MHz 166MHz or By SPD The Choices 100MHz 133MHz By SPD default 166MHz 12 M7VIT Pro BIOS Setup DRAM Timing This item determines DRAM clock timing follow SPD or not The Choices Auto By SPD default Manual Turbo Ultra DRAM CAS Latency When DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The Choices 2 5 default 2 Bank Interleave This item allows you to enable or disable the bank interleave feature The Choices Disabled default 2 bank 4 bank Precharge to Active Trp This items allows you

Biostar M7VIT Pro Owner's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents