Biostar I865G-M4 Owner's Manual
Contents
1. Video Off In Suspend This determines the manner in which the monitor is blanked The Choices Yes default No Suspend Type Select the Suspend Type The Choices Stop Grant default PwrOn Suspend MODEM Use IRQ This determines the IRQ which can be applied in MODEM use The Choices 3 default 4 5 7 9 10 11 NA Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off The Choices Disabled default 1Min 2Min 4Min 8Min 12Min 20Min 30Min 40Min 1Hour HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active The Choices Disabled default 1Min 2Min 3Min 4Min 5Min 6Min 7Min 8Min 9Min 10Min 11Min 12Min 13Min 14Min 15Min Soft Off by PW R BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft Off state when the system has hung The Choices Delay 4 Sec Instant Off default Intruder Detection This item allows you to enable or disable intruder detection The Choices Disabled Default Enabled Wake Up by PCI card When you select Enable a PME signal from PCI card returns the system to Full On state The Choices Enabled Disabled default 22 I865G M4 BIOS Setup USB KB Wake Up From S3 This item allows you to enable or disabled USB keyboard wake up from S3 The Choices D2. round JATXPWR2 I865G M4 CHAPTER 4 USEFUL HELP 4 1 AWARD BIOS BEEP CODE Beep Sound Meaning k One long beep followed by two short Video card not found orv ideo card beeps memory bad High low siren sound PU overheated System will shut down automatically One Short beep when system boot up No error found during PO ong beeps every other second No DRAM detected or install 4 2 EXTRA INFORMA TION BIOS Update After you fail to update BIOS or BIOS isinvaded by virus the Boot Block function will help to restore BIOS If the following message is shown after boot up the system it means the BIOS contents are corrupted In this Case please follow the procedure below to restore the BIOS 1 Make a bootable floppy disk 2 Download the Flash Utility AWDFLASH exe from the Biostar website www biostar com tw 3 Confirm motherboard model and download the respectively BIOS from Biostar website Copy AWDFLASH exe and respectively BIOS into floppy disk Insert the bootable disk into floppy drive and press Enter System will boo up to DOS prompt Type Awdflash xxxx bf sn py r in DOS prompt System will update BIOS automatically and restart The BIOS has been recovered and will work properly OOOO Gl ps I865G M4 B CPU Overheated If the system shutdown automatically after poweron system for seconds that means the CPU protection function has been activated When the CPU is over hea
3. I865G M4 BIOS Setup The Choices 3F8 IRQ4 default Disabled Auto 2F8 IRQ3 3E8 IRQ4 2E8 IRQ3 Onboard Serial Port 2 Select an address and corresponding interrupt for the first and second serial ports The Choices 2F8 IRQ3 Disabled default Auto 3F8 IRQ4 3E8 IRQ4 2E8 IRQ3 UART Mode Select This item allows you to determine which Infrared IR function of onboard I O chip The Choices Normal ASKIR IrDA default SCR UR2 Duplex Mode Select the value required by the IR device connected to the IR port Full duplex mode permits simultaneous two direction transmission Half duplex mode permits transmission in one direction only at a time The Choices Half default Full Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O Address The Choices 378 IRQ7 default 278 IRQ5 3BC IRQ7 Disabled Parallel Port Mode The default value is SPP SPP default Using Parallel port as Standard Printer Port EPP Using Parallel port as Enhanced Parallel Port ECP Using Parallel port as Extended Capabilities Port ECP EPP Using Parallel port as ECP amp EPP mode ECP Mode Use DMA Select a DMA Channel for the port The Choices 3 default 1 Power After Power Fail This setting specifies whether your system will reboot after a power fail or interrupts occurs Off Leaves the computer in the power off state On Reboots the computer Former Sts Restore
4. 11 46 am 21 I865G M4 oltage Panel Click the Voltage button in Main Panel the button will be highlighted and the Voltage Panel will slide out to up as the following figure In this panel you can dedde to increase CPU core voltage and Memory voltage or not The default setting is No If you wantto get the best performance of overclocking we recommend you click the option Yes go 1200 FM 22 I865G M4 Overclock Panel Click the Overclock button in Main Panel the button will be highlighted and the Overclock Panel will slide out to left as the following figure gt ua z D E Aerer Desi PA Ww E ey ae 11 NL Ran 5 u 00 8 is We AER on i p E Tetigi 132 8 Reset o Syren Desanti Setingi aes rd a 3H Hz Bulttn siz Buton WE Blio MH Suton iO 0 nem Overdoc Panel contains the these features 8MHz button 1 MHz button 1MHz button and 3MHz button provide user the ability to do real time overclock adjustment Warning Manually overclock is potentially dangerous especially when the overclocking percentage is over 110 We strongly recommend you verity ev ery speed you overclock by click the Verify button Or you can just click Auto ov erclock button and let WarpSpeeder automatically gets the best resultfory ou Recovery Dialog button Pop up the following dialog Let user selecta restoring way if system need to do a fail safe reboot Piene saint a ncc y oben hal val
5. Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults Reset Configuration Data The system BIOS supports the PnP feature which requires the system to record which resources are assigned and protects resources from conflict Every peripheral device has a node which is called ESCD This node records which resources are assigned to it The system needs to record and update ESCD to the memory locations These locations 4K are reserved in the system BIOS If the Disabled default option is chosen the system s ESCD will update only when the new configuration varies from the last one If the Enabled option is chosen the system is forced to update ESCDs and then is automatically set to the Disabled mode The above settings will be shown on the screen only if Manual is chosen for the resources controlled by function Legacy is the term which signifies that a resource is assigned to the ISA Bus and provides non PnP ISA add on cards PCI ISA PnP signifies that a resource is assigned to the PCI Bus or provides for ISA PnP add on cards and peripherals The Choices Disabled default Enabled 24 I865G M4 BIOS Setup Resources Controlled B By Choosing Auto ESCD default the system BIOS will detect the system resources and automatically assign the relative IRQ and DMA channel for each peripheral By Choosing Manual the user will need to assign IRQ am
6. P et ake 26 9 Frequency Control iei riae cete ir te eet vs 28 I865G M4 BIOS Setup BIOS Setup Introduction This manual discussed Award Setup program built into the ROM BIOS The Setup program allows users to modify the basic system configuration This special information is then stored in battery backed RAM so that it retains the Setup information when the power is tumed off The Award BIOS installed in your computer system s ROM Read Only Memory is a custom version of an industry standard BIOS This means that it supports Intel Pentium 4 processor input output system The BIOS provides critical low level support for standard devices such as disk drives and serial and parallel ports Adding important has customized the Award BIOS but nonstandard features such as virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system The rest of this manual is intended to guide you through the process of configuring your system using Setup Plug and Play Support These AWARD BIOS supports the Plug and Play Version 1 0A specification ESCD Extended System Configuration Data write is supported EPA Green PC Support This AWARD BIOS supports Version 1 03 of the EPA Green PC specification APM Support These AWARD BIOS supports Version 1 1 amp 1 2 of the Advanced Power Management APM specification Power management features are implemented via the Sys
7. darrie weed kod of ecto you rari io de alter sciam lakia bebe D pii Group C Hede bo Handvee D eak CPL Clock Vales I865G M4 d Auto overclock button User can dick this button and WarpSpeeder M will set the best and stable performance and frequency automatically WarpSpeeder utility will execute a series of testing until system fail Then system will do fail safe reboot by using Watchdog function After reboot the WarpSpeeder utility will restore to the hardware default setting orload the verified best and stable frequency according to the Recovery Dialog s setting e Verify button User can dick this button and WarpSpeeder will proceed a testing for current frequency If the testing is ok then the current frequency will be saved into system registry If the testing fail system will do a fail safe rebooting After reboot the WarpSpeeder utility will restore to the hardware default setting orload the verified best and stable frequency according to the Recovery Dialog s setting Note Because the testing programs invoked in Auto overclock and Verify include DirectDraw Direct3D and DirectShow tests the DirectX 8 1 or newer runtime library is required And please make surey our display card s color depth is High color 16 bit or True color 24 32 bit that is required f or Direct3D rendering 5 Hardware Monitor Panel Click the Hardware Monitor button in Main Panel the button will be h
8. data please carefully follow the procedures to avoid damaging the motherboard JCMOS1 Assignment O Normal Operation Def aut Pin 1 2 close 1 Clear CMOS data Pin 2 3 dose X Clear CM OS Procedures Remove AC power line Set the jumper to Pin 2 3 dose Wait for five seconds Set the jumper to Pin 1 2 dose Power on the AC Reset your desired password or clear the CMOS data ON ye ee I865G M4 JPANEL1 Front Panel Connector This 24 pin connector indudes Power on Reset HDD LED PowerLED Sleep button speaker and IrDA Connection It allows user to connect the PC case s front panel switch functions 2 o olle e e e e 2 P ime s njesisoobs JpANEL1 Pin Assignment Function Pin Assignment Sleep EE mene E NA TERI Somer cee LED 9 HDD LED Hard drive MEE LED Power LED TT HEE LED LED Power LED Grund Reset Power ballon a messo ton UE purum 7 gp cime e 7 iE Ky 5V IrDA CUR IrDA Connector Connector JATXPWRI JATXPWR2 Power Connectors JATXPWR 1 This connector allows user to connect 20 pin power connectoron the ATX power supply JAT XPWR2 By connecting this connector it wil provide 12V to CPU power drcuit Pin 3 3V 3 3V z uw ejay 3 Ground EA cron Oe 3 Ground o o 5 16 Ground 2 sns Ground Papen LE E Standby vorage rev T9 V Heu ajv
9. data by setting the JCOMS1 2 3 closed as ON status All the CMOS data will be loaded as defaults setting Method 2 Press the lt Insert gt key and Power button simultaneously after that keep on pressing the lt Insert gt key until the power on screen showed This action will boot up the system according to FSB of the processor X It s strongly recommended to set CPU Vcore and clock in default setting If the CPU Vcore and clock are not in default setting it may cause CPU or M B damage 29
10. of 1 5Gb s Pin Assignment Pin Assignment Lese san2 DS PX e 7 Oud 1 10 I865G M4 CHAPTER 3 HEADERS amp JUMPERS SETUP 3 1 HOW TO SETUP JUMPERS The illustration shows how to set up jumpers When the jumper cap is placed on pins the jumperis close if not that means the jumperis open Jj mi 1 2 i Pin opened Pin dosed Pin1 2 closed 3 2 DETAIL SETTINGS JU SBV 1 J U SBV 2 JUSBV3 4 Power Source Headers for USB ports at JUSB1 JUSBLAN1 amp JUSB2 JU SB3 JUSBV1 JUSBV2 Desorption JUSBV3 4 JUSBVT 5V for JKBMS1 and JUSBT Se sy JUSBV2 5V for JUSBLAN1 Pin 1 2 close JUSBV3_ 4 5V for JUSBV2 JUSBV3 JUSBV1 JKBMS1 and JUSB1 are powered by standby voltage of 5V 1 meg JUSBV2 JUSBLAN1 is powered with Pin 2 3 close standby voltage of 5V JUSBS 4 JUSB2 3 are powered by standby voltage of 5V Note In order to support this function Power on system via USB device JUSBV1 JUSBV2 JUSBV3 4 jumper cap should be placed on Pin 2 3 individually JCDIN 1 CD ROM Audio in Connector This connector allows user to connect the audio source from the veriaty devices like CD ROM DVD ROM PCI sound card PCITV turner card etc Pin Assignment Left channel input 2 round Right channel input 11 I865G M4 JSPDIF_OUT1 Digital A udio out Connector optional This connector allows user to connect the PCI bracket SPDIF output header HHD
11. sspoiF our 2 SPDIFOUT O a Ground JSPDIF_IN1 Digital Audio in Connector optional This connector allows user to connect the PCI bracket SPDIF input header Pin l BEER o me JAUDIO2 Front Panel Audio Header optional This header allows user to connect the front audio out put cable with the PC front panel It will disable the output on back panel audio connectors ier 99 7 2 JAUJDIO2 round Mic power Bass 4 Audio power 9 Right line out Speaker out Right 6 Right line out Speaker out Right DS Saar lt ONERE 9 Left ine oul Speaker out Left 10 Left Tine ouvSpeaker out Left JUSB2 JUSB3 Front USB Headers This header allows user to connect additional USB cable on the PC front panel and also can be connected with internal USB devices like USB card reader Pin Assignment Pin Assignment 5V fused 5V fused USE ve 5 Us use 8 Ground o Ky 0m I865G M4 JDJ1 optional AUDIO DJ Connector a oam Pin Assignment Pin Assignment 5 SMBDATA SMBCLK 3 INT B Key EMT AXTPWROK JCL1 Chassis Open Header This connector allows sy stem to monitor PC case open status If the signal has been triggered it will record to the CMOS and show the message on next boot up Pin Assignment JCL1 JCM OS1 Clear CM OS Header By placing the jumper on pin2 3 it allows user to restore the BIOS safe setting and the CMOS
12. to configure the onboard IDE Controllers IDE HDD Block Mode Block mode is also called block transfer multiple commands or multiple sector read write If your IDE hard drive supports block mode most new drives do select Enabled for automatic detection of the optimal number of block mode most new drives do select Enabled for automatic detection of the optimal number of block read write per sector where the drive can support The Choices Enabled default Disabled IDE DMA Transfer Access This item allows you to enable or disable the IDE transfer access The Choices Enabled default Disabled On Chip Primary Secondary PCI IDE This item allows you to enable or disable the primary secondary IDE Channel The Choices Enabled Default Disabled Primary Secondary Master Slave PIO The IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the IDE devices that the onboard IDE interface supports Modes 0 to 4 16 I865G M4 BIOS Setup will increased performance progressively In Auto mode the system automatically determines the best mode for each device The Choices Auto default Mode0 Model Mode2 Mode3 Mode4 Primary Secondary Master Slave UDMA Ultra DMA 100 functionality can be implemented if it is supported by the IDE hard drives in your system As well your operating environment requires a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If
13. with passwords to bring the system online and or to use the CMOS Setup Utility System A password is required for the system to boot and is also required to access the Setup Utility Setup default A password is required to access the Setup Utility only This will only apply if passwords are set from the Setup main menu APIC Mode Selecting Enabled enables ACPI device mode reporting from the BIOS to the operating system The Choices Enabled default Disabled MPS Version Control For OS The BIOS supports version 1 1 and 1 4 of the Intel multiprocessor specification Select version supported by the operation system running on this computer The Choices 1 4 default 1 1 11 I865G M4 BIOS Setup OS Select For DRAM gt 64MB A choice other than Non OS2 is only used for OS2 systems with memory exceeding 64MB The Choices Non OS2 default OS2 Summary Screen Show This item allows you to enable disable the summary screen Summary screen means system configuration and PCI device listing The choices Enabled Disabled default 12 I865G M4 BIOS Setup 4 Advanced Chipset Features This submenu allows you to configure the specific features of the chipset installed on your system This chipset manage bus speeds and access to system memory resources such as DRAM It also coordinates communications with the PCI bus The default settings that came with your system have been optimized and therefore should
14. I865G M4 FCC Information and Copyright This equipment has been tested and found to comply with the limits of a Class B digital device pursuant to Part 15 of the FCC Rules T hese limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications There is no guarantee that interference will not occur in a particular installation The vendor makes no representations or warranties with respect to the contents here ofand specially disclaims any implied warranties of merchantability or fitness for any purpose Further the vendor reserves the right to revise this publication and to make changes to the contents here of without obligation to notify any party beforehand Duplication of this publication in part orin whole is not allowed without first obtaining the vendor approval in writing The content of this users manual is subject to be changed without notice and we will not be responsible for any mistakes found in this users manual All the brand and product names are trademarks of their respective companies Table of Contents Chapter 1 Introduction rere 1 1 1 I865G M4 Features essssssseseeeeneeennennen 1 1 2 Package Contents sssssss
15. Increase the numeric value or make changes Key Decrease the numeric value or make changes Esc key Main Menu Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu Exit Current page and return to Main Menu F1 key General help on Setup navigation keys F5 key Load previous values from CMOS F7 key Load the optimized defaults F10 key Save all the CMOS changes and exit I865G M4 BIOS Setup 1 Main Menu Once you enter Award BIOS CMOS Setup Utility the Main Menu will appear on the screen The Main Menu allows you to select from several setup functions Use the arrow keys to select among the items and press lt Enter gt to accept and enter the sub menu 6 WARNING The information about BIOS defauls on this manual Figure 1 2 3 4 5 6 7 8 9 is just only for reference please refer to the BIOS installed on board for update information W Figure 1 Main Menu Phoenix AwardBIOS CHOS Setup Utility Standard CMOS Features gt Frequency Voltage Control Advanced BIOS Features Load Optimized Defaults Advanced Chipset Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status Upgrade BIOS Quit Menu in BIOS Tle z Select Item Save amp Exit Setup Time Date Hard Disk Type Standard CM OS Features This submenu contains industry standard configurabl
16. N1 CPUfan power header I865G M4 CHAPTER 2 HARDWARE INSTALLATION 2 1 CENTRAL PROCESSING UNIT CPU Step 1 Pull the lever sideways away from the socket and then raise the lever up to a 90 degree angle Step 2 Lookfor the white dot cut edge The white dot cut edge should point wards the lever pivot The CPU will fitonly in the correct orientation Step 3 Hold the CPU down fimly and then dose the lever to complete the installation Step 4 Put the CPU Fan on the CPU and bucke it Connect the CPU FAN power cable to the JCFAN1 This completes the installation 2 2 FAN HEADERS These fan headers support cooling fans built in the computer The fan wiring and plug may be different according to the fan manufacturer Connect the fan cable to the connector while matching the black wire to pin CPU FAN Header JCFAN1 1 G d 1 Gron oem JCFAN1 12V System Fan Header JSFAN1 Pin Ground FAN RPM rate sense Note TheJCFAN1 and JSFAN1 support 3 pin head connector When connecting with wires onto connectors please notethat thered wireisthe positi veand should beconnected to pin 2 and theblack wireis Ground and 7 I865G M4 should beconnected to GND I865G M4 2 3 MEMORY MODULE INSTALLATION 1 Unlocka DIMM slot by pressing the retaining dips outward Align a DIMM on the slot such thatthe notch on the DIMM matches the breakon the Slot 2 Insert the DIMM vertically and firmly into the slot unt
17. Tle lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults I865G M4 BIOS Setup Main Menu Selections This table shows the selections that you can make on the Main Menu Item Options Description Date mm dd yy Set the system date Note that the Day automatically changes when you set the date Time hh mm ss Set the system internal clock IDE Primary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Primary Slave Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Master Options are in its sub Press Enter to enter the menu sub menu of detailed options IDE Secondary Slave Options are in its sub Press Enter to enter the menu sub menu of detailed options 360K 5 25 in Select the type of floppy Drive A 1 2M 525 in disk drive installed in your system 720K 3 5 in Drive B 1 44M 3 5 in 2 88M 3 5 in None Video EGA VGA Select the default video CGA 40 device CGA 80 MONO I865G M4 BIOS Setup Item Options Description Halt On All Errors Select the situation in which No Errors you want the BIOS to stop Base Memory All but Keyboard All but Diskette All but Disk Key N A the POST process and notify you Displays the amount of conventional memory dete
18. ain M emory E Support 4 DDR data channels with 2 DIMMs per channel I Available bandwidth up to 3 2GB s DDR400 for single channel mode and 6 4GB s DDR400 for dual channel mode I Supports 256Mb 512Mb and 1Gb DDR technologies for x8 or x 16 non ECC DDR devices I Supports only x8 and x16 DDR devices Does not support registered DIMM or double sided x16 DIMMs I Supports 4 bank devices dual channel DDR266 333 400 MHZ I Registered DIMMs not supported I Maximum memory size is up to 4GB DIMM Location DDR Module Total real DDRA1 128MB 256MB 512MB 1 E 2 Lid DDRA2 128MB 256MB 512MB 1GB 1 DDRB1 128MB 256MB 512MB 1GB 1 DDRB2 ONEEC T 5 EL SAU T up to 4GB I865G M4 10 100 PCI LAN I Chip RTL8100C Supports 10 100Mb s auto negotiation I Supports ACPI power management L Half Full duplex capability Slots E 3 32bit PCI bus master slots I 1 AGP x4 x8 slot Super I O I Chip ITE IT8712F L Low pin count interface I Provides the most commonly used legacy super I O functionality I Environment Control initiatives H W Moniter ITE s Smart Guardian function Onboard IDE E Supports 4 IDE disk drives I Provide PIO mode 0 4 bus master and Ultra DMA33 66 1 00 function E Serial ATA 150 controller integrated in ICH5 Connects up to 2 SATA drives Up to 150MB s transfer speeds Compliants with SATA 1 0 specification Onboard A C 97 Sound Codec i Chip ALC655 I Compliants wit
19. appropriate when testing and results in system fail or hang WarpSpeeder technology assures the system stability by automatically rebooting the computer and then restart to a speed that is either the original system speed or a suitable one 5 2 SYSTEM REQUIREMENT OS Support Windows 98 SE Windows Me Windows 2000 Windows XP DirectX DirectX 8 1 or above The Windows XP operating system indudes DirectX 8 1 If you use Windows XP you do not need to install DirectX 8 1 I865G M4 5 3 INSTALIATION 1 Execute the setup execution file and then the following dialog will pop up Please dick Next button and followthe default procedure to install atcome bo fhe booted Wired bo alas paced EI PUT TI k Pe org IET PT pales Taonia Head 2 When you see the following dialog in setup procedure it means setup is completed If the Launch the WarpSpeeder Tray Utility checkbox is checked the Tray Icon utility and WarpSpeeder M utility will be automatically and immediately launched after you dick Finish button Vrat d a Fach ied UC cede Zaig ha bred ri aleng e aoe m poa Copel EJ Lern tg et pee ee Ebo U sage The following figures are just only for reference the screen printed in this user manual will change according to your motherboard on hand 19 I865G M4 5 4 WARPSPEEDER INCLUDES 1 TRAY ICON AND 5 PANELS 1 Tray Icon Whenever the Tray Icon utility is launched it will display a little tray
20. ault Enabled Delay Prior to Thermal Set this item to enable the CPU Thermal function to engage after the specified time The Choices 4 8 16 default 32 AGP Aperture Size MB Select the size of the Accelerated Graphics Port AGP aperture The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host 14 I865G M4 BIOS Setup cycles that hit the aperture range are forwarded to the AGP without any translation The Choices 64 4 8 16 32 128 default 256 Init Display First This item allows you to decide to active whether PCI Slot or on chip VGA first The Choices Onboard AGP default PCI Slot On Chip VGA This item allows you to enabled or disabled on chip VGA The Choices Enabled default Disabled On Chip Frame Buffer Size This item allows you to choose the on chip frame buffer size The Choices 16MB default 8MB I MB Boot Display This item allows you to choose the display booting The Choices Auto default CRT TV EFP 15 I865G M4 BIOS Setup 5 Integrated Peripherals W Figure 5 Integrated Peripherals rdBll Integrated Peripher Awa etup Uti y als gt OnChip IDE Device Press Enter gt Onboard Device Press Enter gt SuperI0 Device Press Enter t1l Move Enter Select PU PD Value F10 Save ESC Exit Fi General Help F5 Previous Values F7 Optimized Defaults Onboard IDE Device Press Enter
21. cted during boot up Extended Memory N A Displays the amount of extended memory detected during boot up Total Memory N A Displays the total memory available in the system I865G M4 BIOS Setup 3 Advanced BIOS Features W Figure 3 Advanced BIOS Setup Phoenix AwardBIOS CHOS Setup Utility Advanced BIOS Features Boot Seq amp Floppy Setup Press Enter Item Help Cache Setup Press Enter CPU Feature Press Enter Menu Level Ld Virus Warning Disabled Hyper Threading Technology Enabled Quick Power On Self Test Enabled Boot Up NumLock Status On Gate A20 Option Fast Typematic Rate Setting Disabled Security Option Setup APIC Mode Enabled MPS Version Control For 0SI 1 41 OS Select For DRAM gt 64MB Non 0S21 Summary Screen Show Disabled Tle Move Enter Select PU PD Value F1 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults Boot Seq amp Floppy Setup First Second Third Boot Other Device These BIOS attempt to load the operating system from the device in the sequence selected in these items The Choices Floppy LS120 HDD 0 SCSI CDROM HDD 1 HDD 2 HDD 3 ZIP 100 LAN HPT370 Disabled Enabled Swap Floppy Drive For systems with two floppy drives this option allows you to swap logical drive assignments The Choices Disabled default Enabled Boot Up Floppy Seek Enabling this option will test the flo
22. d Fast gives faster performance and slow gives more stable performance This field applies only when synchronous DRAM is installed in the system The Choices 4 default 3 2 DRAM RAS Precharge If an insufficient number of cycle is allowed for RAS to accumulate its charge before DRAM refresh the refresh may be incomplete and the DRAM may fail to retain data Fast gives faster performance and Slow gives more stable performance This field applies only when synchronous DRAM is installed in the system The Choices 4 default 3 2 Memory Frequency For This item allows you to select the Memory Frequency The Choices Auto default DDR266 DDR300 DDR400 System BIOS Cacheable Selecting Enabled allows you caching of the system BIOS ROM at F0000h FFFFFh resulting a better system performance However if any program writes to this memory area a system error may result The Choices Enabled default Disabled Video BIOS Cacheable Select Enabled allows caching of the video BIOS resulting a better system performance However if any program writes to this memory area a system error may result The Choices Disabled Enabled default Memory Hole At 15M 16M You can reserve this area of system memory for ISA adapter ROM When this area is reserved it cannot be cached The user information of peripherals that need to use this area of system memory usually2 discussed their memory requirements The Choices Disabled def
23. e options Advanced BIOS Features This submenu allows you to configure enhanced features of the BIOS Advanced Chipset Features This submenu allows you to configure special chipset features I865G M4 BIOS Setup Integrated Peripherals This submenu allows you to configure certain IDE hard drive options and Programmed Input Output features Power Management Setup This submenu allows you to configure the power management features PnP PCI Configurations This submenu allows you to configure certain Plug and Play and PCI options PC Health Status This submenu allows you to monitor the hardware of your system Frequency Control This submenu allows you to change CPU Vcore Voltage and CPU PCI clock However this function is strongly recommended not to use Not properly change the voltage and clock may cause CPU or M B damage Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence These configurations are factory settings optimized for this system A confirmation message will be displayed before defaults are set Load Optimized Defaults V N N Set Supervisor Password Setting the supervisor password will prohibit everyone except the supervisor from making changes using the CMOS Setup Utility You will be prompted with to enter a password Enter Password Set User Password If the Supervis
24. g Technology This option allows you to enable or disabled CPU Hyper Threading Enabled for Windows XP and Linux 2 4 x OS optimized for Hyper Threading Technology Disabled for other OS OS not optimized for Hyper Threading Technology The Choices Enabled Default Disabled Quick Power On Self Test Enabling this option will cause an abridged version of the Power On Self Test POST to execute after you power up the computer Disabled Normal POST Enabled default Enable quick POST 10 I865G M4 BIOS Setup Boot Up NumLock Status Selects the NumLock State after power on On default Numpad is number keys Off Numpad is arrow keys Gate A20 Option Select if chipset or keyboard controller should control Gate A20 Normal A pin in the keyboard controller controls Gate A20 Fast default Lets chipset control Gate A20 Typematic Rate Setting When a key is held down the keystroke will repeat at a rate determined by the keyboard controller When enabled the typematic rate and typematic delay can be configured The Choices Disabled default Enabled Typematic Rate Chars Sec Sets the rate at which a keystroke is repeated when you hold the key down The Choices 6 default 8 10 12 15 20 24 30 Typematic Delay Msec Sets the delay time after the key is held down before it begins to repeat the keystroke The Choices 250 default 500 750 1000 Security Option This option will enable only individuals
25. h AC 97 version 2 3 specification E Supports 6 channels I Supports stereo MIC Front Side On board Peripherals I 1 front panel header supports front panel facilities 1 CD in connector supports 1 CD ROM audio in device 1 front audio header supports front panel audio function 1 S PDIF out connector supports digital audio out function 1 chassi s open header supports PC case opened warning function I865G M4 1 Floppy port supports 2 FDD with 360K 720K 1 2M 1 44M and 2 88Mbytes 2 USB headers support 4 USB 2 0 ports 2 IDE connectors support 4 hard disk devices 2 serial ATA connectors support 2 SATAdevices Rear Side Connectors E 4 USB 2 0 ports 1 VGAport 1 serial port 1 parallel port 1 RJ 45 LAN jack 1 PS 2 Mouse amp Keyboard port 1 vertical audio port including 1 line in connector 1 line out connector and 1 MIC in connector sLutdy ANT KME ES PS 2 Mouse Py2 Keyboard USB x2 LAN qAGDEY Line In Surround Line Out Mic In 1 Base Center fo JCOMI JVGAT B BIOS amp Software BIOS E Award legal BIOS E SupportsAPM1 2 E Support ACPI E Support USB funciton Software E Support WarpSpeeder 9th Touch Raser M winRasher V E Offers the highest performance for Windows 98SE Windows 2000 Windows ME Windows XP SCO Unix and Red Hat Linux etc doo oo RRTA E I865G M4 PACKAGE CONTENTS FDD cable x1 HDD cable x1 User s manual x1 Fu
26. he palette will not show up on the ISA bus if the PCI VGA controller responds to the Write In this case the PCI VGA controller should not respond to the Write it should only snoop the data and permit the access to be forwarded to the ISA bus The non VGA ISA graphic controller can then snoop the data on the ISA bus Unless you have the above situation you should disable this option Disabled default Disable the function Enabled Enable the function 25 I865G M4 BIOS Setup 8 PC Health Status W Figure 8 PC Health Status Phoenix Awardb tup PC Health Status Shutdown Temperature Disabled Menu Level Shov H W Monitor in POST Enabled TheerMove EnterrSelect PU POrValue FIOsSave CSCrExit FirGeneral Help F FS Previous Values 7 Optimized Defaults Shutdown Temperature This item allows you to set up the CPU shutdown Temperature This item is only effective under Windows 98 ACPI mode The Choices 60 C 140 C 65 C 149 F Disabled default CPU Vcore AGP Voltage 3 3V 5 0V 12V 12V 5V 5V SB _ Voltage Battery Detect the system s voltage status automatically Current CPU Temp Show you the current CPU temperature Current CPU FAN Speed This field displays the current CPUFAN speed 26 I865G M4 BIOS Setup Current SYS FAN Speed This field displays the current speed SYSTEM fan Show H W Monitor in POST If you computer contain a monitoring system it will sh
27. icon on the right side of Windows Taskbar QO 1133 4M This utility is responsible for conveniently invoking WarpSpeeder Utility You can use the mouse by clicking the left button in order to invoke WarpSpeeder directly from the little tray icon or you can right click the little tray icon to pop up a popup menu as following figure The Launch Utility item in the popup menu has the same function as mouse left click on tray icon and Exit item will dose Tray Icon utility if selected Lanoch Utility Ext fer Serer I865G M4 2 Main Panel If you click the tray icon WarpSpeeder utility will be invoked Please refer to the following figure the utility s first window you will see is Main Panel M ain Panel contains features as follows a Display the CPU Speed CPU external clock Memory cock AGP dock and PCI clock infomation b ContainsAbout Voltage Overclock and Hardware Monitor Buttons for invoking respective panels c With a user friendly Status Animation it can represent 3 overclock percentage stages Man walking gt overclock percentage from 100 110 96 Panther running overclock percentage from 11096 120 Car racing overclock percentage from 120 above MHz Du o Bo Ree cpu GLOCK MHz PCICLOCK MHz CEA 66 5 E 7 OVER CLOCK 400 pA wEMORY CLOCK 32 7 PERCENTAGE Hardware Monitor Button i L Over clock percentage 100 m Overclock Bullion x Voltage Button O V
28. ighlighted and the Hardware Monitor panel will slide out to left as the following figure In this panel you can get the real time status infomation of your System The information will be refreshed every 1 second E 0 02m I865G M4 6 About Panel Click the about button in Main Panel the button will be highlighted and the About Panel will slide out to up as the following figure In this panel you can get model name and detail information in hints of all the chipset that are related to overclocking You can also get the mainboard s BIOS model and the Version number of WarpSpeeder utility 25 I865G M4 Note Because the overclock overvoltage and hardware monitor features are controlled by several separate chipset WarpSpeeder divide these features to separate panels If one chipsetis not on board the correlative button in Main panel will be disabled but will not interfere other panels functions This property can make WampSpeeder M utility more robust 10 08 2004 26 I865G M4 BIOS Setup BIOS SCG m IB Maiti ldem EE 3 2 St ndard C MOS Features er enter ertet per 6 3 Advanced BIOS Features iu oiu e t EC e CO eee dtt exe 9 4 Advanced Chipset Features sess 13 5 Integrated Peripherals vimi ert mere ee does 16 6 Power Management Setup esses eene nne 20 T PnP PCI Configurations ie or Ht deer ORRUR 24 8 PC Health Status oe ec tnter tte eee tete
29. il the retaining chip snap back in place and the DIMM is properly seated I865G M4 2 4 CONNECTORS AND SLOTS Accelerated Graphics Port Slot AGP1 Yourmonitor will attach directly to that video card This motherboard supports video cards for PCI slots butitis also equipped with an Accelerated Graphics Port AGP An AGP card will take advantage of AGP technology for improved video effidency and performance especially wth 3D graphics Floppy Disk Connector FDD1 The motherboard provides a standard floppy disk connector that supports 360K 720K 1 2M 1 44M and 2 88M floppy disktypes This connector supports the provided floppy drive ribbon cables Hard Disk Connectors IDE1 IDE2 The motherboard has a 32 bit Enhanced PCI IDE Controller that provides PIO Mode 0 5 Bus Master and Ultra DMA 33 66 100 functionality It has two HDD connectors IDE1 primary and IDE2 secondary The IDE connectors can connect a master and a slave drive so you can connect up to four hard disk drives The first hard drive should always be connected to IDE1 Peripheral Component Interconnect Slots PCI 1 3 This motherboard is equipped with 5 standard PCI slots PCI stands for Peripheral Component Interconnect and itis a bus standard for expansion cards This PCI slotis designated as 32 bits Serial ATA Connectors SATA1 2 The motherboard has a PCI to SATA Controller with 2 channels SATA interface it satisfies the SATA 1 0 spec and wih transfer rate
30. isabled Default Enabled Resume by Alarm This function is for setting date and time for your computer to boot up During Disabled you cannot use this function During Enabled Choose the Date and Time Alarm Date f Month Alarm You can choose which month the system will boot up Time hh mm ss Alarm You can choose shat hour minute and second the system will boot up Note If you have change the setting you must let the system boot up until it goes to the operating system before this function will work 23 I865G M4 BIOS Setup 7 PnP PCI Configurations This section describes configuring the PCI bus system PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU itself uses when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make any changes to the default settings W Figure 7 PnP PCI Configurations Phoenix AwardBIOS CHOS Setup Utility PnP PCI Configurations Reset Configuration Data Disabled Resources Controlled By AutoCESCD Menu Level gt Default is Disabled PCI UGA Palette Snoop Disabled Select Enabled to reset Extended System Configuration Data ESCD when you exit Setup if you have installed a new add on and the system reconfiguration has caused such a serious conflict that the OS cannot boot ti e Move
31. isks are capable of breaking down at any time System only boots from optical drive i Back up data and applications Hard disk can be read and applications files can be used but booting from hard disk 2 Ref ormat the hard driv e is impossible Re install applications and data using backup disks Configuration or CMOS Failure correct inf ormation is in setup Cannot boat system after installing 1 Set master slave jumpers second hard drive correctly Run SETUP program and select correct drive types Call the drive manuf acturers f or compatibility with other drives 17 I865G M4 CHAPTER 5 WARPSPEEDER 5 1 INTRODUCTION WarpSpeeder a new powerful control utility features three user friendly functions including Overclock Manager Overvoltage Manager and Hardware Monitor With the Overdock Manager users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click The Overvoltage Manager on the other hand helps to power up CPU core voltage and Memory voltage The cool Hardware Monitor smarty indicates the temperatures voltage and CPU fan speed as well asthe chipset information Also in the About panel you can get detail descriptions about BIOS model and chipsets In addition the frequency status of CPU memory AGP and PCI along with the CPU speed are synchronically shown on our main panel Moreover to protect users computer systems if the setting is not
32. lly setup driver CD x1 Rear I O panel for Micro ATX case x1 USB2 0 cable x1 optional S PDIF cable x1 optional Serial ATA cable x1 optional Serial ATA power switch cable x1 optional I865G M4 LAYOUT OF I865G M4 E pl JATXPWRI Cr LE um Socket 478 jJ 1 Eri TB E Vy RT n Cha Cy Cia JVGAT s t oum E o iona ES LANI B IDE2 JAUDIO1 RTL81 00C iin Fin 4 JC DIN1 ik JCM 2 1 JPANEL1 gl WE Note ll represents the t pin I865G M4 1 4 A B JATXPWR2 ATX power source header JUSBV1 Power source header for JKBMS1 amp JUSB1 Rear side connectors back panel JAUDIO2 Front panel audio out header JUSBV2 Power source header for JUSBLAN f JSPDIF OUT1 JSPDIF IN1 Ditigal audio out in connectors JCDIN1 CD ROM audio in connector PCI1 3 Peripheral Component Interconnect slots JUSB2 3 Front USB ports headers JSFAN1 System fan power header JDJ1 Audio DJ header COMPONENTS OF I865G M4 lt o SATA1 2 Serial ATA on board connectors JCL1 Chassis open messege header JPANEL1 Front panel facilities header JCMOS1 Clear CMOS header JUSBV3_4 Power source header for JUSB2 3 AGP1 Accelerated Graphics Port slot IDE1 2 Hard disk connectors FDD1 Floppy disk connector JATXPWR 1 ATX power source header DDRA1 A2 B1 B2 DDR Memory modules JCFA
33. not be changed unless you are suspicious that the settings have been changed incorrectly W Figure 4 Advanced Chipset Setup Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing Selectable By SPD 2 CAS Latency Time Active to Precharge Delay 8 Menu Level DRAM RAS to CAS Delay 4 DRAM RAS Precharge 4 Memory Frequency For Auto system BIOS Cacheable Enabled Video BIOS Cacheable Enabled Memory Hole At 15M 16M Disabled Delay Prior to Thermal 16 Min AGP Aperture Size MB 128 Init Display First Onboard AGP on chip VGA Enabled On chip Frame Buffer Size 16MB Boot Display Auto Tl Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults DRAM Timing Selectable When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The Choices By SPD default Manual CAS Latency Time When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing The Choices 1 5 2 default 2 5 3 Active to Precharge Delay This item controls the number of DRAM clocks to activate the precharge delay The Choices 8 default 7 6 5 13 I865G M4 BIOS Setup DRAM RAS to CAS Dela This field let you insert a timing delay between the CAS and RAS strobe signals used when DRAM is written to read from or refreshe
34. on but system will need AGP driver to initialize the card So if the AGP driver of the VGA card does not support the initialization feature the display may work abnormally or not function after S3 The Choices Auto default Yes No 20 I865G M4 BIOS Setup Power Management This category allows you to select the type or degree of power saving and is directly related to the following modes 1 HDD Power Down 2 Doze Mode 3 Suspend Mode There are four options of Power Management three of which have fixed mode settings Min Saving Minimum power management Doze Mode 1 hr Standby Mode 1 hr Suspend Mode 1 hr HDD Power Down 15 min Max Saving Maximum power management only available for sl CPU s Doze Mode 1 min Standby Mode 1 min Suspend Mode 1 min HDD Power Down 1 min User Defined default Allows you to set each mode individually When not disabled each ofthe ranges are from 1 min to 1 hr except for HDD Power Down which ranges from 1 min to 15 min and disable Video Off Method This option determines the manner in which the monitor is goes blank V H SYNC 4Blank This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer Blank Screen This option only writes blanks to the video buffer DPMS default Initial display power management signaling 21 I865G M4 BIOS Setup
35. or Password is not set then the User Password will function in the same way as the Supervisor Password If the Supervisor Password is set and the User Password is set the User will only be able to view configurations but will not be able to change them Enter Password I865G M4 BIOS Setup Save amp Exit Setup Save all configuration changes to CMOS memory and exit setup Confirmation message will be displayed before proceeding SAVE to CMOS and EXIT Y N V Exit Without Saving Abandon all changes made during the current session and exit setup Confirmation message will be displayed before proceeding Quit Without Saving Y N N Upgrade BIOS This submenu allows you to upgrade bios BIOS UPDATE UTILITY Y N N I865G M4 BIOS Setup 2 Standard CMOS Features The items in Standard CMOS Setup Menu are divided into 10 categories Each category includes no one or more than one setup items Use the arrow keys to highlight the item and then use the lt PgUp gt or lt PgDn gt keys to select the value you want in each item W Figure 2 Standard CMOS Setup Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Time hh mm ss Oe NE A Menu Level gt IDE Primary Master IDE Primary Slave change the day month IDE Secondary Master year and century IDE Secondary Slave Drive A 1 44M 3 5 in Drive B None Video EGA VGA Halt On A1 But Keyboard
36. ow PC health status during POST stage The item offers several delay time to select you want The Choices Enabled default Disabled 27 I865G M4 BIOS Setup 9 Frequency Control W Figure 9 Frequency Control pela 1X fwardBIOS CHOS Setup Utility BES Frequency Voltage Control CPU Voltage Default DIMM Voltage 2 50 Menu Level gt futo Detect PCI Clk Enabled Spread Spectrum Enabled CPU Clock 100 tie Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F7 Optimized Defaults CPU Clock Ratio The Choices 8 X default 9X 10X 11X 12X 13X 14 X 15X 16X 17X 18X 19X 20 X 21 X 22 X 23 X CPU Voltage This item allows you to select CPU Voltage Regulator The Choices Default default 8 196 45 596 42 596 DIMM Voltage This item allows you to select DDR Voltage Regulator The Choices 2 5V Default 2 6V 2 7V 2 8V Auto Detect PCI Clk This item allows you to enable disable auto Detect PCI Clock The Choices Enabled default Disabled Spread Spectrum This item allows you to enable disable spectrum for all clock The Choices Enabled default Disabled 28 I865G M4 BIOS Setup CPU Clock This item allows you to select CPU Clock and CPU over clocking If unfortunately the system s frequency that you are selected is A not functioning there are two methods of booting up the system Method 1 Clear the COMS
37. p DMA for add on cards Be sure that there are no IRQ DMA and I O port conflicts IR Resources This submenu will allow you to assign each system interrupt a type depending on the type of device using the interrupt When you press the Press Enter tag you will be directed to a submenu that will allow you to configure the system interrupts This is only configurable when Resources Controlled By is set to Manual IRQ 3 assigned to PCI Device IRQ 4 assigned to PCI Device IRQ 5 assigned to PCI Device IRQ 7 assigned to PCI Device IRQ 9 assigned to PCI Device IRQ 10 assigned to PCI Device IRQ 11 assigned to PCI Device IRQ 12 assigned to PCI Device IRQ 14 assigned to PCI Device IRQ 15 assigned to PCI Device PCI VGA Palette Snoop Choose Disabled or Enabled Some graphic controllers which are not VGA compatible take the output from a VGA controller and map it to their display as a way to provide boot information and VGA compatibility However the color information coming from the VGA controller is drawn from the palette table inside the VGA controller to generate the proper colors and the graphic controller needs to know what is in the palette of the VGA controller To do this the non VGA graphic controller watch for the Write access to the VGA palette and registers the snoop data In PCI based systems where the VGA controller is on the PCI bus and a non VGA graphic controller is on an ISA bus the Write Access to t
38. ppy drives to determine if they have 40 or 80 tracks Disabling this option reduces the time it takes to boot up The Choices Disabled Enabled default Report NO FDD for Win95 The Choices NO default I865G M4 BIOS Setup Cache Setup CPU L1 amp L2 Cache Depending on the CPU chipset in use you may be able to mcrease memory access time with this option Enabled default Enable cache Disabled Disable cache CPU Feature Thermal Management Allows you to choose the thermal management of your monitor The Choices Thermal Monitor 1 default Thermal Monitor2 TM2 Bus Ratio Represents the frequency Bus ratio of the throttled performance state that will be initiated when the on die sensor gose from not hot to hot The Choices 0X default TM2 Bus VID Represents the voltage of the throttled performance state that will be initiated when the on die sensor gose from not hot to hot The Choices 0 8375 default Limit CPU ID Max Val Set limit CPU ID maximun vale to 3 it should be disabled for WinXP The Choices Disabled default Enabled Virus Warning This option allows you to choose the Virus Warning feature that is used to protect the IDE Hard Disk boot sector If this function is enabled and an attempt is made to write to the boot sector BIOS will display a warning message on the screen and sound an alarm beep Enabled Virus protection is activated Disabled default Virus protection is disabled CPU Hyper Threadin
39. s the system to the status before power failure or interrupt occurs The Choices Off default On Former Sts 19 I865G M4 BIOS Setup 6 Power Management Setup The Power Management Setup Menu allows you to configure your system to utilize energy conservation and power up power down features W Figure 6 Power Management Setup Phoenix AwardBIOS CMOS Setup Utility Power Management Setup S1 POS ACPI Suspend Type Menu Level Power Management User Define Video Off Method DPMS Video Off In Suspend Yes Suspend Type Stop Grant MODEM Use IRQ 3 Suspend Mode Disabled HDD Power Down Disabled Soft Off by PWR BTTN Instant Off Intruder Detection Disabled Wake Up by PCI card Disabled Power On by Ring Disabled Resume by Alarm Disabled Tle Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help FS5 Previous Values F7 Optimized Defaults ACPI Function This item displays the status of the Advanced Configuration and Power Management ACPI The Choices Enabled default Disabled ACPI Suspend Type The item allows you to select the suspend type under the ACPI operating system The Choices S1 POS default Power on Suspend 3 STR Suspend to RAM S1 amp S3 POS STR Run VGABIOS if S3 Resume Choosing Enabled will make BIOS run VGA BIOS to initialize the VGA card when system wakes up from S3 state The system time is shortened if you disable the functi
40. s you to enable or disable the USB Mouse Legacy Support Enabled Enable USB Mouse Support Disabled default Disable USB Mouse Support AC97 Audio This item allows you to decide to enable disable to support AC97 Audio The Choices Auto default Disabled Onboard PCI LAN This item allows you to enable or disable the Onboard PCI LAN The Choices Auto default Disabled Onboard LAN Boot ROM This item allows you to enable or disable the Onboard LAN Boot ROM The Choices Enabled default Disabled Super IO Device Press Enter to configure the Super I O Device Power On Function This item allows you to choose the power on function The Choices Button default Password Hot Key Mouse Left Mouse Right Any Key Keyboard 98 KB Power on Possword Input password and press Enter to set the Keyboard power on password HOT Key power ON Input password and press Enter to set the Keyboard power on password The Choices Ctrl F1 default Ctrl F2 Ctrl F3 Ctrl F4 Ctr F5 Ctrl F6 Ctrl F7 Ctrl F8 Ctrl F9 Ctrl F10 Ctrl F11 Ctrl F12 Onboard FDC Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you wish to use it If install and FDC or the system has no floppy drive select Disabled in this field The Choices Enabled default Disabled Onboard Serial Port 1 Select an address and corresponding interrupt for the first and second serial ports 18
41. ssseeeeenee 4 1 3 Layout of l865G MA sess 5 1 4 Components of 865G MA4 ssssssseseee 6 Chapter 2 Hardware Installation 7 2 1 Central Processing Unit CPU 7 2 2 FAN Headers eese ene 7 2 3 Memory Module Installation sese 9 2 4 Connectors and Slots sss 10 Chapter 3 Headers amp Jumpers Setup 11 3 1 How to Setup Jumpers sssese 11 3 2 Detail Settings sssssseseeeeeeene 11 Chapter 4 Useful Help rcr 15 4 1 Award BIOS Beep Code ssssssseee 15 4 2 Extra Infomation sse 15 4 3 Troubleshooting eseeseem 17 Chapter 5 WarpSpeeder ss 18 5 1 Intro dU Cor 2 e E ee ERE teet 18 5 2 System Requirement sssssssseese 18 5 3 Installation ee ert n nee eee 19 5 4 WarpSpeeder includes 1 tray icon and 5 panels 20 I865G M4 CHAPTER 1 INTRODUCTION 1 1 1865G M4 FEATURES A Hardware CPU I Support Socket 478 I Supports Intel Pentium 4 processor up to 3 06GHz Support Northwood and Prescott CPU up to 3 4GHz Does not support Willamette CPU I Front Side Bus at 400 533 800M Hz E Supports Intel Hyper Threading Technology Chipset I North Bridge Intel 865G I South Bridge Intel ICH5 Dimensions I Micro ATX Fom Factor 24 4cm W x 23 5em L M
42. ted the motherboard will shutdown automatically to avoid a damage of the CPU and the system may not power on again In this case please double check 1 The CPU cooler surface is placed evenly with the CPU surface 2 CPU fan is rotated normally 3 CPU fan speed is fulfilling wth the CPU speed After confirmed please follow steps below to relief the CPU protection function 1 Remove the power cord from power supply for seconds 2 Wait for seconds 3 Pluginthe power cord and boot up the system Or you can 1 Clearthe CMOS data See Close CMOS Header JCMOS1 section 2 Wait for seconds 3 Power on the system again 16 I865G M4 4 3 TROUBLESHOOTING Probable Solution No power to the system at all Make sure power cable is Power light don t illuminate f an securely plugged in inside power supply does not turn 2 Replace cable on 7 Contact technical support Indicator light on key board does not turn on ystem inoperative Keyboard lights Using even pressure on both ends of are on power indicator lights are lit the DIMM press down firmly until the and hard drive is spinning module snaps into place System does not boat from hard disk 1 Check cable running from disk to driv e can be bootedf rom optical driv e disk controller board Make sure both ends are securely plugged in check the driv e type in the standard CMOS setup Backing up the hard drive is extremely important All hard d
43. tem Management Interrupt SMI Sleep and Suspend power management modes are supported This AWARD BIOS can manage power to the hard disk drives and video monitors ACPI Support Award ACPI BIOS support Version 1 0 of Advanced Configuration and Power interface specification ACPI It provides ASL code for power management and device configuration capabilities as defined in the ACPI specification developed by Microsoft Intel and Toshiba I865G M4 BIOS Setup PCI Bus Support This AWARD BIOS also supports Version 2 1 of the Intel PCI Peripheral Component Interconnect local bus specification DRAM Support DDR DRAM Double Data Rate Synchronous DRAM are supported Supported CPUs This AWARD BIOS supports the Intel Pentium 4 CPU Using Setup In general you use the arrow keys to highlight items press Enter to select use the lt PgUp gt and lt PgDn gt keys to change entries press F1 for help and press lt Esc gt to quit The following table provides more detail about how to navigate in the Setup program by using the keyboard Keystroke Function Up arrow Move to previous item Down arrow Move to next item Left arrow Move to the item on the left menu bar Right arrow Move to the item on the right menu bar Move Enter Move to the item you desired PgUp key Increase the numeric value or make changes PgDnkey Decrease the numeric value or make changes Key
44. your hard drive and your system software both support Ultra DMA 100 select Auto to enable BIOS support The Choices Auto default Disabled On Chip Serial SATA This item allows you to choose Disabled disabled SAT A Controller Auto auto arrange by BIOS Combined Mode PATA and SATA are combined max of 2 IDE drivers in each channel Enhanced Mode enabled both SATA and PATA max of 6 IDE drivers are supported SATA Only SATA is operating in legacy mode The Choices Default default Auto Combined Mode Enhanced Mode SATA only Serial ATA Port Mode The Choices Primary Master default Serial ATA Porti Mode The Choices Primary Master default Onboard Device Press Enter to configure the onboard Device USB Controller Select Enabled if your system contains a Universal Serial Bus USB controller and you have USB peripherals The Choices Enabled default Disabled USB 2 0 Controller This entry is to enabled disabled EHCI controller only This BIOS itself may may not have high speed USB support If the BIOS has high speed USB support built in the support will automatically turn on when high speed device were attached The Choices enabled default 17 I865G M4 BIOS Setup USB Keyboard Support This item allows you to enable or disable the USB Keyboard Legacy Support Enabled Enable USB Keyboard Support Disabled default Disable USB Keyboard Support USB Mouse Support This item allow
Download Pdf Manuals
Related Search