BALAY 3TI60081A Installation Manual
Contents
1. No water can be seen in the drum Water emerges from beneath the washing machine Foam escapes from detergent drawer Several attempts to start spinning Washing is not spun properly Washing results not satisfactory Detergent residues on the washing The mains plug is not correctly plugged in Plug in the mains plug correctly The door is not properly closed Close the door The tap is not turned on Turn on the tap Filter in the water inlet hose is blocked Clean the filter in the water inlet hose gt page 17 The water inlet hose is pinched or kinked The washing machine is not correctly levelled Check the water inlet hose Level the washing machine gt page 23 The transport locks have not been re moved Outlet hose fitted too low Not a fault Inlet hose screw connection is leaking Remove the transport locks gt page 23 Fit the outlet hose correctly gt page 25 During certain programmes the water level is below the visible range Tighten the screw connection Outlet hose is leaking Water pump cover not properly closed Too much detergent has been used Not a fault The unbalanced load detection system attempts to redistribute an unbalanced load by repeatedly starting to spin Large items are not distributed evenly in the drum Spin speed is automatically reduced for safety reasons Soiling heavier than assumed Have2. H A A Q max 900 mm min 500 mm lt 3 Water connection or 1400 mm Q Q ur D roo 76 kg Right hand connection bo Sd max 900 mm gt lt 7 COT EE if min 500 mm To prevent leaks or water damage you must observe the instructions in this section N B Operate the washing machine only with cold drinking water Do not connect to the mixer tap of an unpressurised hot water boiler If in doubt have a technician connect the appliance Do not use a used inlet hose Only use the inlet hose supplied or one which was purchased from an authorised specialist retailer The water inlet and outlet hoses can be routed to the left of right depending on installation conditions 24 Water inlet Water outlet Drainage into a siphon Electrical connection Do not allow the water inlet hose to be Kinked or squashed modified and cut strength no longer guaranteed Note the water pressure in the mains supply The water pressure should be between 50 900 kPa 0 5 9 bar at least 8 litres of water per minute flow when the tap is open If the water pressure is higher a pressure reducing valve must be installed Connect the inlet hose to the cold water tap Tighten the screw connections only by hand Do not remove the filter from the inlet hose After connecting the water inlet hose Open the water tap carefully checking the leak tightness of the
3. Off Unplug the mains plug from the socket Unscrew the water inlet hose from the tap Clean the filter with a small brush Reconnect the hose Turn on the water tap Check whether water comes out of the end of the hose If water is escaping check that the filter is correctly seated QOHOOO0oOoO0Ouo0v oOOu O Remove the hose from the water tap O Rinse out the filter under running water O Connect the hose Cleaning the filter on the washing machine O Remove the hose from the rear of the washing machine Cleaning the filter on the washing machine O Pull out the filter and rinse out under running water O Insert the filter and connect the hose O Turn on the tap and check whether water still escapes If water still escapes check that the filter is seated correctly O Turn off the water tap What to do it A Fault code rapid flashing of the following indicator lights Risk of electric shock technicians Repairs must only be carried out by customer services or authorised If repairs are needed or if you cannot rectify a fault yourself with the help of the following table O Turn off the tap Remedial action O Set the programme selector to Off O Disconnect the washing machine from the mains O Call the after sales service gt page 21 lavado wash The door is not properly closed Close the door centrifug spin lavado wash 3 centrif
4. This washing machine complies with Hazard warnings A Before using for the first time When washing A To protect the washing machine WEEE bx This washing machine is intended exclusively for domestic use for washing machine washable fabrics and hand washable woollens in detergent solution for operation using cold drinking water and standard detergents and care products which are suitable for use in washing machines relevant safety regulations Risk of electric shock To remove the mains plug only pull directly on the plug itself not on the plug cable Never insert or pull out the plug if your hands are wet Risk of suffocation Keep packaging plastic film and packing parts out of the reach of children Danger of death When appliances have reached the end of their service life pull out the mains plug Cut off the mains cable and remove it with the plug Destroy the loading door lock Children cannot then lock themselves in and put their life in danger Risk of poisoning Keep detergents and care products out of the reach of children Risk of explosion After being placed in the washing machine items of laundry which have been pretreated with cleaning agents containing solvent e g stain remover or cleaning solvents may cause an explo sion Hand rinse items of laundry thoroughly beforehand Risk of injury The loading door can become very hot Exercise caution when
5. Water is not flowing in See Fault Water not running in aclar enxag rinse lavado wash w flot Rinse stop Other fault codes are intended The water is not drained See Fault Water is not emptied exclusively for the after sales service Note down the fault code for the after sales service Fault Programme does not start Washing machine not react ing The water is not drained Detergent residues in the detergent drawer Possible cause Start Pause button not pressed Remedial action Press the lt gt inicio pausa Start Pause button Power failure Start programme immediately Press the inicio pausa Start Pause button The door is not properly closed Close the door Plug not inserted properly into socket Programme fault Outlet hose is twisted Detergent solution pump is blocked Damp or lumpy detergent Insert plug correctly You can use the Reset function to return to the original settings To do this press and hold the inicio pausa Start Pause button until all three programme progress lights light up Fit the outlet hose correctly Clean the detergent solution pump gt page 16 Clean and dry the detergent drawer gt page 15 Use the measuring aid for liquid detergent Water is not flowing in Intense vibrations during spinning Constant inflow of water The water is pumped out again directly through the outlet hose
6. label Press the button again to restart the programme Clean the fabric softener compartment insert and fit it correctly in the compartment amp gt page 15 Programme will continue when power is restored If washing is removed during a power failure first drain off the water gt page 16 Check whether the plug is plugged into the socket correctly the circuit breaker fuse has tripped Call the after sales service Select the programme w Empty and press lt gt inicio pausa Start Pause The programme is running or the door is locked for safety reasons Wait until the End indicator light flashes Power failure Unlock the loading door mechanically Set the programme selector to stop Off Select any programme The washing machine checks whether opening the loading door is possible Otherwise see Programme termination gt page 14 Emergency release In order to unlock the door mechanically in the event of a power failure you will have to socket same time O set the programme selector to stop Off and unplug the mains plug from the O open the base panel and drain out the water gt page 16 O pull the emergency release downwards and open the loading door at the Before opening the loading door make sure that there is no water or hot washing water in the appliance Under no circumstances open the door with the emergency release while the drum is st
7. lf you are in any doubt please consult with the after sales service or your dealer Do not install the washing machine outdoors or in areas which are prone to frost Frozen hoses may tear or burst The washing machine could suffer damage Do not stand the washing machine upside down or place it on its side Do not lift the washing machine by any of the protruding parts e g loading door Remove the transport locks and cross connectors and store in a safe place In addition to the instructions provided in this document special regulations from the relevant water and electric utility companies may apply If in doubt have a technician connect the appliance Num Description ber 4 Covers for openings left after removing the transport locks 1 Spanner for removing the transport locks and adjusting the feet 1 1 24 40 mm dia hose clamp for connection to a siphon 1 Door template 2 Door hinges with screws 1 Screw with washer for decor door On the rear of the washing machine drum Water outlet hose Water inlet hose Mains cable with plug Instruction manual and booklet containing after sales service addresses Moisture may remain in the drum following the final inspection which every washing machine undergoes before leaving the factory 22 Removing the transport locks Unscrew all four screws Completely remove all transport locks and using the span
8. program selector to a 60 C programme O Press the inicio pausa Start Pause button O At the end of the programme set the programme selector to stop Off O Open the door Leave the loading door open in order that the inside of the washing machine can dry Preparing and sorting the laundry Sorting laundry for washing Lil Check the manufacturer s care instructions and care labels The laundry may be damaged if you do not observe the fabric care symbols Knitwear made of wool or which contains a proportion of wool must have the label machine washable Wash white laundry separately from coloureds Sort according to type colour level of soiling and temperature New coloured laundry should be washed separately Risk of discolouration Unhemmed or torn items should not be washed in the machine as they may fray Do not exceed the permissible load capacity gt page 27 Sorting laundry according to the information on the care labels Preparing laundry for washing Loading the laundry A Only wash laundry with the following care labels Care label Type of laundry Cottons 90 C tiay Va077 V307 Coloureds 60 C 40 C 30 C Easy care 60 C 40 C 30 C 04 NAOT VA V0 VA Hand and machine washable silk and wool cold 40 C 30 C Laundry with care symbol Ye Do not wash Loose foreign bodies e g coins paper clips needles nails may damage the laun
9. the outlet hose replaced by the after sales service Clean the detergent solution pump gt page 16 Only use fabric compatible detergent which is suitable for use in washing machines Make sure that you use the correct dosage Always wash large and small items together Always wash large and small items together Select a suitable programme e g a programme with prewash Pretreat stains if necessary Too little or incorrect detergent used Use the correct dosage of a suitable detergent in accordance with the manufacturer s instructions Maximum load exceeded Some phosphate free detergents contain water insoluble residues which appear on washing as light specks Select the correct load for the programme Rinse washing again or change to liquid detergent Brush washing after drying 19 Grey residues on the washing Programme terminated unexpectedly The fabric softener is not completely flushed in or too much water remains in the compartment amp No response from the indicator lights The door cannot be opened Soiling caused by ointments grease or oil Amount of detergent too low Q inicio pausa Start Pause button selected by mistake The fabric softener compartment insert is not correctly attached or is blocked Power failure Rinse stop selected Wash the laundry using the maximum detergent dosage and the maximum permissible temperature see the care
10. 20 kWh 49 0 47 h Programme setting for testing in accordance with applicable standard EN60456 Note for comparison tests For testing the test programmes with specified load quantity and maximum spin speed wash by selecting the Intensive option The values may deviate from the indicated values depending on water pressure water hardness and inlet temperature ambient temperature type amount and soiling of the laundry detergent used fluctuations in the power supply and which additional functions are selected 28 Index A Adding laundry 14 C Care information Washing 8 Care product 9 Cleaning Control panel 15 Detergent drawer 15 Detergent solution pump 16 Drum 15 Housing 15 Water inlet hose 17 Connection fittings 24 Consumption rates 28 Control panel 6 Cleaning 15 D delicado delicates Programmes 11 27 28 Descaling 15 Detergent 9 Liquid detergent insert 9 10 Liquid detergent insert 10 Detergent drawer Cleaning 15 Description 9 Detergent solution pump Cleaning 16 Dimensions 24 Display Fault message 18 Door 13 Draining the water 16 Drum Cleaning 15 E Economy tips 4 Electrical connection 25 Emergency release 20 Empty 11 Special programmes 11 13 14 17 20 End of the programme 13 Environmental protection 4 F Fault message 18 Faults 18 Filter Water inlet hose 17 First wash 7 Function selection buttons
11. 3550 ESPANA STI60081A 3T160101A 12 2010 9000586513 19291011000
12. 6 H Hazard warnings Detergent 9 Housing Cleaning 15 Included with the appliance 22 inicio pausa Start Pause Button 12 Control panel 6 Installation surface 22 L lana la wool Programmes 11 Laundry Loading 8 Preparing for washing 8 Sorting for washing 7 Levelling 23 Liquid detergent insert 9 Loading door 5 29 P Power 28 Programme change 13 Programme duration 28 Programme progress Control panel 6 Programme selector 6 11 Programme termination 14 R Remedial action 18 Reset function 14 resistentes algod cottons Programmes 11 13 28 resistentes algod cottons extra Programmes 28 Rinse Spin Special programmes 11 14 17 Rinse stop Control panel 6 S Safety information 3 15 18 22 sinteticos easy care Programmes 11 27 Special programmes 11 Spin Special programmes 11 Spin speed Control panel 6 Washing options 12 T Table of programmes 27 Transport locks 23 U Unbalanced load detection system 12 W Washing 13 Washing options Indicator lights 6 Washing programmes 11 Water 28 Water inlet 25 Water inlet hose Cleaning 17 Water outlet 25 WEEE 3 30 31 Further information about our products accessories spare parts and service can be found at http www balay es or via our after sales service centres BSH Electrodome sticos Espana S A Itaroa 1 31620 HUARTE PAMPLONA NIF VAT A 2889
13. art Pause button until all three programme progress lights light up Cleaning and care Safety information A Housing and control panel Washing drum Descaling the washing machine Risk of electric shock The appliance must first be disconnected from the mains Never clean the washing machine with a jet of water Risk of explosion Never clean the washing machine with solvents Risk of scalding Hot detergent solution must be allowed to cool before being drained Remove detergent residues immediately Wipe away with a soft damp cloth Cleaning with a jet of water is prohibited Remove any foreign bodies from the drum and rubber seals Leave the loading door open in order that drum can dry Use chlorine free cleaning agents Follow the information provided by the manufacturer Never use steel wool lf there are detergent or care product residues Pull out the detergent drawer as far as the stop Press on the zone marked PUSH and take out the detergent drawer Clean the detergent drawer guide Remove the fabric softener compartment insert Clean the detergent drawer and fabric softener compartment insert under running water Insert the fabric softener compartment insert Insert the detergent drawer OO aaao Not necessary if the correct measures of detergent are used but if still required follow the information provided by the descaler manufacturer Suitable descalers can be ordered
14. centrif Unbalanced load detection system w flot button Rinse stop lt gt inicio pausa button Start Pause Programme progress The maximum spin speed depending on model programme table gt page 27 is reduced by 200 rpm This programme reduces the formation of creases By repeatedly starting and stopping drum spinning the unbalanced load detection system ensures that the laundry is evenly distributed For safety reasons the speed of the final spin is reduced or the spin cycle is not run if the laundry is very unevenly distributed The laundry remains in the last water used for rinsing Suitable for delicate fabrics and curtains gt page 13 Press lt gt inicio pausa Start Pause to start the selected programme Display of programme progress by indicator lights lighting up preparado ready lavado wash After switching on the washing machine the indicator lights lavado wash preparado ready flash When the programme is started lavado wash remains constantly lit aclar enxag rinse The light remains lit during rinsing Rinse stop selected all indicator lights are switched off Button lt Soo centrif Rinse stop flashes centrifug spin Light remains lit during spinning When spinning has finished centrifug spin fin fim finished flashes fin dim finished Washing Washing End of the programme w flot Rinse stop Programme change O Set the p
15. connec tion points N B The screw connection is under mains water pressure i gt Do not kink the outlet hose or pull it lengthways Height difference between the installation surface and the drain max 90 cm min 50 cm Secure the connection point with the 24 40 mm hose clamp The washing machine must only be connected to an alternating current via a properly installed earthed socket Only use earth leakage circuit breakers with the following symbol The mains voltage must correspond to the voltage specifications on the washing machine rating plate The connected load and fuse required are specified on the rating plate Make sure that the mains plug fits the socket the cable cross section is adequate the earthing system is properly installed the appliance is not standing on the mains cable the mains plug is accessible at all times Changes to the mains cable may only be carried out by a qualified electrician Do not use multiple plugs adapters or extension cables Mains plug Do not insert the plug into the socket or pull it out if your hands are wet When removing the plug from the socket pull on the plug body only not the cable Never pull the plug out during operation 25 After the washing machine has been installed in the fitted kitchen it can Fitting the door hinges be concealed by a door In this case the hinges included in the delivery must be fit
16. drawer is divided into three compartments Compartment Detergent for prewash Compartment II Detergent for main wash Compartment 8 Liquid additives such as starch and fabric softener Additives are automatically flushed into the machine during the last wash cycle Do not exceed the maximum capacity otherwise compartment may be emptied too early Dilute viscous additives with water before adding them to the detergent drawer compartment to prevent blockages Liquid detergent insert must be folded down before liquid detergents are used To do this O Pull out the detergent drawer as far as the stop O Press on the blue zone marked PUSH and fully remove the detergent drawer gt page 15 O Pull the blue insert in compartment II fully forward and fold downwards O Insert the detergent drawer Do not use the insert push upwards with gel type detergents and washing powder or if using programmes with Prewash Risk of poisoning Keep detergents and care products out of the reach of children Risk of injury Exercise caution when opening the detergent drawer There may still be detergent residues left in the drawer Select the correct dosage for the detergent according to the amount of laundry the instructions of the detergent manufacturer how dirty the laundry is water hardness You can find out about the water hardness in your area from your local waterworks Using the corr
17. dry and components of the washing machine e g the drum OQoOoOo0o00 o Empty the pockets of all items Brush any sand out of pockets and collars Pretreat any stains Close zips do up cover buttons Remove curtain fittings or place curtains in a laundry bag Wash the following in a laundry bag pillowcase Delicates e g tights curtains small items of laundry e g socks or handkerchief underwired bras the underwiring may come loose during the washing process and cause damage Turn trousers knitwear and jersey fabrics e g hosiery T shirts or sweatshirts inside out Before loading the washing machine make sure that there are no inappropriate objects or pets in the drum Risk of explosion Items that have been pretreated with cleaning agents containing solvents e g stain remover or stain solvent must be carefully rinsed by hand before they are loaded into the machine o o o o o o Unfold the laundry and place it loosely into the drum Load large and small items together Check the maximum drum loads programme table gt page 27 Take care not to trap items of laundry between the door and the rubber seal Close the door You will hear it click shut Measure out appropriate amounts of detergent and care products and pour into the machine Turn on the water tap Detergents and care products Detergent drawer Detergents and care products A The detergent
18. ease In the event of a power cut the door can be released mechanically gt page 20 Control panel Indicator lights for Function selection buttons with indicator lights programme progress Show the selected settings Shows the programme w flot Rinse stop progress and the centrif reduce maximum spin speed by programme status 200 rpm depending on model Operating condition Function selection buttons inicio pausa Programme selector Programme selector gt page 11 inicio pausa start pause Switches the washing machine button gt page 12 on and off and for selecting the Starts the selected programme turnable in both programme directions Reset function Do not change the position of the Resets to the original programme selector during settings gt page 14 washing Before washing for the first time Lil The washing machine was tested before leaving the factory In order to remove any testing water which may be remaining run the first washing cycle without any laundry O Make sure that the transport locks on the back of the washing machine have been removed gt page 23 O Do not load any laundry O Close the loading door urn on the water tap ull out the detergent drawer dd 1 2 a measuring cup of detergent to compartment Il gt page 9 OO rus Do not use detergents for woollens or delicates these cause foaming O Close the detergent drawer Turn the
19. ect dosage reduces the impact on the environment and gives a good washing result Measuring washing powder Measuring liquid detergent H Lil Normally soiled laundry O Set the programme O Add all the detergent according to the manufacturer s instructions to compartment Il of the detergent drawer Only use pH neutral wool detergent for woollens programmes Add fabric softener to compartment 8 Heavily soiled laundry O Set programme with prewash O Add 1 4 of the recommended amount of detergent to compartment of the detergent drawer and 3 4 of the detergent to compartment II Only use liquid detergent for the main wash cycle To do this O Add the recommended amount of detergent to a liquid detergent measuring aid and place it in the drum or O After folding down the liquid detergent insert pour the detergent into compartment Il of the detergent drawer Use the scale on the liquid detergent insert as a guide for the dosage of liquid detergent lf compartment Il is used for washing powder the liquid detergent insert must be folded up Programmes Programme selector Washing programmes Depending on model Special programmes The programme selector is used to set the washing and drying pro grammes resistentes algod Cottons Suitable for hard wearing fabrics heat resistant fabrics made from cotton or linen Coloureds up to 60 C Whites 60 C up to 90 C resis
20. emptying hot detergent solution Do not climb onto the washing machine Do not lean on the loading door when it is open Do not reach into the drum if it is still turning Install the washing machine according to the installation instructions gt page 23 Remove the transport locks and keep them in a safe place Do not operate the washing machine if it shows visible signs of damage If you are in any doubt please consult with the after sales service or your dealer Remove all objects from pockets paying particular attention to sources of ignition e g lighters matches etc Do not leave children unsupervised near the washing machine The washing machine must not be used by children or persons who have not been instructed in its use Keep pets away from the washing machine Exercise caution when emptying hot detergent solution The door can become very hot during operation Do not climb onto the washing machine Do not lean on the door of the washing machine when it is open Do not install the washing machine in an area which is prone to frost because hoses may burst or tear if they freeze Do not transport the washing machine without the transport locks in place This appliance is designated according to European Directive 2002 96 EC which governs waste electrical and electronic equipment WEEE The directive provides a framework for the return and recycling of u
21. ill turning If you cannot correct a fault yourself switching on off or a repair is required Set the programme selector to stop Off and unplug the mains plug from the socket Turn off the tap and call the after sales service gt page 21 20 After sales service E Nr Before you call the after sales service please check first whether you can correct the fault yourself gt page 18 You will be charged if a technician is called out even during the warranty period You can find your nearest after sales service here or in the enclosed after sales service directory depending on model Please give the after sales service the product number E no and production number FD of the appliance Enter the numbers of your appliance here You can find this information on the rating plate in the frame of the loading door Please help us to avoid unnecessary after sales service call outs by quoting the appliance and production numbers This will also save you the related additional costs Trust the expertise of the manufacturer Contact us for assistance In this way you can rest assured that the repair will be carried out by trained service technicians using original spare parts 21 Installation instructions Safety information A Included with the appliance The Washing machine is very heavy Exercise caution when lifting Do not operate the washing machine if it shows visible signs of damage
22. ner take the mains cable out of the retainers supplied Insert the protective machine from being damaged covers Before using the appliance for the first time ensure that all transport locks have been removed and kept safe for any subsequent transport ce For transporting at a later stage You must make sure that the transport locks are refitted which will prevent the washing Positioning and levelling Levelling Appliance stability is essential to ensure that the washing machine does not creep during spin cycles The installation area must be firm clean and level Parquet floors and soft floor coverings e g carpets or foam backed floor coverings are unsuitable Intense noise vibrations and wandering may be the result of incorrect levelling All four appliance feet must stand firmly on the ground The washing machine must not rock Check the alignment of the washing machine with a spirit level and adjust if necessary The washing machine must not rest against the side panels of the installation recess The lock nuts on the front feet of the appliance must be screwed firmly against the housing with the spanner 23 Dimensions Width x depth x height 596 mm x 585 mm x 818 mm Weight Hose and cable lengths Left hand connection 8 S a m m m 4 m 4 4 4 m 4 4 H H
23. ooo O T Please read the installation and operating instructions and all the ILL other information supplied and handle the appliance accordingly Keep all documents in a safe place for future reference or to pass on to the next owner For further information and a selection of our products visit our website htto www balay es Table of contents Operating instructions Installation instructions Appendix General safety information ctevscvlscsccaecvecadiaeus Sieadessdasdecn decvdeadeecars 3 Environmental protection economy tipS uu ccseseeseseeeteeeeeees 4 Your new washing Machine accsssisicessaxaucstewennercaseaveetedemataneveuced 5 Before washing for the first time ccescssesssessssssssesseseseees 7 Preparing and sorting the laundry ssssssssssssssssrssrsrrerrerrerennns 7 Detergents and care products sssesseisrssrssrsrierrerrnrisrrnrrnrrnrnns 9 Programmes ari e E E 11 Washing OPON S ein e a a aa aa 12 Washing ateei r T a E a 13 Cleaning and care sesessssssrssssersrisssrsrrsrnsirisrnsrnrstnsrnsrrrsrnsrarernnns 15 Whatto do Ii iai etini ar a a n iaiki 18 Aftersales SerniCE neea niaan EE Ea R 21 Installation INStrUCH ONS Scezees sansaycechcentcecuecuecbenesvsdtestdascaxauceaecse 22 Table of programmes cisitucissteteeleesschcssxcecinesiresbask suarecdttenscteteee 27 Cons mpton Tates nee ct hist e aon as 28 igre Pa Copeman ce ne ee irene ene a or ea E aE da 29 General safety information Intended use
24. rogramme selector to the desired programme e g resistentes algod Cottons 60 C O The lavado wash preparado ready indicator light flashes O Where required reduce the spin speed or select w flot Rinse stop gt page 12 O Load the laundry gt page 8 Observe the maximum load Programme table gt page 27 O Press the lt inicio pausa Start Pause button The washing programme starts The lavado wash indicator light lights up The washing programmes are automatically ended O Set the programme selector to stop Off O Remove the washing from the drum O Leave the loading door open in order that the inside of the washing machine can dry O Turn off the water tap If the spin function was deactivated at the start of washing w flot Rinse stop Without final spin laundry remains in the last water used for rinsing the washing programme is stopped after the last rinse In order to drain the rinsing water and if required spin the laundry O Set the programme selector to spin By pressing the centrif button the spin speed can be reduced by 200 rpm The water is emptied and the washing machine spins The maximum spin speed depends on the selected washing programme If you do not wish to spin the laundry O Set the programme selector to ww B Empty The water is emptied but the washing machine does not spin The programme has finished when the fin fim finished indicator light flashe
25. s O Set the programme selector to stop Off O Remove the laundry O Leave the loading door open in order that the inside of the washing machine can dry You have selected an incorrect programme by mistake O Select the programme again and press O inicio pausa Start Pause The new programme starts from the beginning Adding laundry Programme termination Reset function If you want to add laundry after the programme has started press and hold the inicio pausa Start Pause button until the lavado wash flashes The washing machine checks whether adding laundry is possible Select the inicio pausa Start Pause button to continue the programme Note If the water level and or temperature is high or if the machine is spinning the loading door remains locked for safety reasons Press and hold the inicio pausa Start Pause button until all three programme progress lights light up To continue the programme select the inicio pausa Start Pause button Press and hold the Q inicio pausa Start Pause button for three seconds For washing programmes at high temperatures Cooling the laundry select wy S Rinse Spin Select inicio pausa Start Pause For programmes with a low temperature Select ex Rinse Spin or w Empty Select inicio pausa Start Pause You can use the Reset function to return to the original settings To do this press and hold the lt inicio pausa St
26. sed appliances which is applicable across the EU Environmental protection economy tips Separate out the various waste materials of the packaging and take them to the nearest collection point Always fill the appliance with the maximum amount of laundry for each programme Wash normally soiled laundry without a prewash Instead of the resistentes algod Cottons 90 C programme select resistentes algod Cottons 60 C extra intensive gt page 11 Comparable cleaning with considerably lower energy consumption Measure the detergent according to the manufacturer s instructions and in line with the local water hardness If the laundry is subsequently dried in a tumble drier select the spin speed according to the tumble drier manufacturer s instructions Your new washing machine Description of the washing machine Loading door You have chosen to buy a modern high quality Balay domestic appliance A distinctive feature of your washing machine is its low energy consumption Every machine which leaves our factory is carefully checked to ensure that it operates correctly and is in perfect condition N B The water inlet hose and water outlet hose must be correctly attached during washing gt page 25 The water tap must be turned open A safety device prevents the door from being opened during operation Before opening Make sure that there is no water in the drum and that the drum is not moving Emergency rel
27. ted to the washing machine to the washing machine 26 Le Table of programmes Observe the information on care labels fabric type and load quantity Type of laundry T A W Ap Options made from wool or a wool blend Programmes C max load max spin speed w flot Rinse stop centrif resistentes algod frio cold 90 1000 rom Hard wearing fabrics heat resistant fabrics made of v v 6 kg cottons cotton or linen sint ticos frio cold 40 3k 800 rpm Easy care fabrics made of cotton linen synthetic v v easy care g fibre or blended fabrics delicado frio cold 600 rpm For delicate washable fabrics e g made of silk v delicates satin synthetic fibres or blended fabrics 2kg e g curtains lana la 4 wool frio cold 30 800 rom Suitable for hand or machine washable fabrics v wv Programmes and options depend on the model Consumption rates Washing Programme Load Power Water Programme duration resistentes algod cottons 0 40 kWh 60 1 51 h frio cold resistentes algod cottons 0 80 kWh 60 1 51 h o 6 kg 40 C resistentes algod Cottons 1 02 kWh 451 2 06 h 60 C extra intensive sint ticos easy care 40 C 3 kg 0 45 kWh 40 1 32 h delicado delicates frio cold 0 11 kWh 35 0 36 h lana la 67 wool frio cold 2 kg 0 05 kWh 49 0 47 h lana la wool 30 C 0
28. tentes algod Cottons 60 C extra Intensive Energy saving programme Because of the extended washing time which also consumes considerably less energy a level of cleaning comparable to the 90 C programme is achieved resistentes algod Cottons prelav Prewash for heavily soiled laundry with additional prewash sint ticos Easy care cold 40 C 60 C Washing programme for less robust fabrics made of cotton linen synthetic fibre or blended fabrics Sorting by colour is recommended delicado Delicates frio cold Low heat programme for delicate washable fabrics e g made of silk satin synthetic fibre or blended fabrics e g curtains Gentle spinning between wash cycles and reduced final spin speed lana la Wool cold 30 C Wool becomes matted under the influence of heat moisture and move ment The woollens programme takes account of these properties and finds the optimum way between drum standstill and movement Suitable for hand or machine washable fabrics made from wool or a wool blend Rinse Spin Wash cycle followed by spinning Fabric softener or starch can also be used in this programme Spin Separate spin cycle Detergent solution or water used for rinsing are emptied before the spin cycle starts w Empty Emptying of the water used for rinsing without final spin cycle after selecting a washing programme with the setting Rinse stop Washing options Button so
29. via our website or from our after sales service gt page 21 Detergent solution pump Notes on blockages O Set the programme selector to stop Off O Use a screwdriver to release the lock pins O Fold up the servicing panel and remove it upwards O Remove the drain hose from its retainer O Remove the sealing cap from the drain tube and allow the water to drain off The container for the drained water may have to be emptied several times When no more water emerges refit the sealing cap O Place the drain hose into the retainer Cleaning the detergent solution pump O Carefully unscrew the pump cover remaining water Clean the interior pump cover threads and pump housing it must be possible to turn the impeller O Replace the pump cover and screw it down O Place the servicing flap into the 4 clip in slots and fasten to the housing with the lock pin is washed Pour 1 litre of water into compartment Il and start the Empty programme il To prevent detergent flowing unused into the outlet the next time laundry If no water or an insufficient amount of water runs into the washing Filter in the water inlet machine first release the water pressure in the inlet hose Turn off the water tap Select any programme except w Rinse Spin 4 8 Empty Press the inicio pausa Start Pause button Allow the programme to run for approximately 40 seconds Set the programme selector to stop
Download Pdf Manuals
Related Search