Home

Avaya P332MF User's Manual

1. Warning Class 1 LED Product Do not view the LED through any magnifying device while it is powered on Never look directly at the fiber Tx port and fiber cable ends when powered on Backup Power Supply BUPS Physical Height Width Depth Weight Power Requirements Input voltage Input current Inrush current Output power Output voltage 2U 88 mm 3 5 482 6 mm 19 450 mm 17 7 10 kg 22 lb 100 240 VAC 50 60 Hz 7 76 A100 VAC 3 82 AQ200 VAC 70 A 100 VAC max 150 A 200 VAC max 4x27 AQ 5 5V 5 5V 156 Avaya P332MF User s Guide Appendix A Specifications Environmental Operating Temp 0 50 C 32 1220F Rel Humidity 5 to 95 non condensing Safety e UL for US approved according to UL1950 Std e C UL UL for Canada approved according to C22 2 No 950 Std e CE for Europe approved according to EN 60950 Std e Overcurrent Protection A readily accessible Listed safety approved protective device with a 16A rating must be incorporated in series with building installation AC power wiring for the equipment under protection EMC Emissions Emissions Approved according to e Europe EN55022 class A 1994 e Europe EN 6150 3 2 Harmonics Current Emissions Europe EN 6150 3 3 Flicker Immunity Approved according to e EN 50082 1 e JEC 150 4 5 BUPS MTBF e 125 194 hrs minimum see Section MTBF in Various Configurations Avaya P332MF User s Guide 157 Appendix
2. ON indicates that the local port will act upon flow control frames received from the far end OFF indicates that the local port will discard flow control frames received from the far end send Controls the sending of IEEE802 3x flow control frames from Gigabit ports only e ON indicates that the local port is allowed to send flow control frames to the far end OFF indicates that the local port is not allowed to send flow control frames to the far end all Controls the sending and receipt of flow control frames for any type of ports ON indicates that the local port will both act upon and send TEEE802 3x flow control frames OFF indicates that the local port will both discard and not send flow control frames of any type PROPRIETARY indicates that the local port will both act upon and send Avaya proprietary flow control frames proprietary A proprietary flow control which may be used when a P330 is connected to M770 10 100 ports or P110 ports module Switch number port number port Output Example P330 1 super set port flowcontrol all 2 20 on Port 2 20 flow control administration status set to on Avaya P332MF User s Guide 113 Chapter 6 CLI Layer 2 set port auto negotiation flowcontrol advertisement The set port auto negotiation flowcontrol advertisement command sets the flowcontrol advertisement for a Gigabit port when performing autonegotiation The syntax for this command is set
3. Output Example P330 N gt show cascading fault monitoring 1 Module 1 cascading down fault monitoring enabled Module 1 cascading up fault monitoring enabled 62 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show port auto negotiation flowcontrol advertisement Usetheshow port auto negotiation flowcontrol advertisement command to display the flowcontrol advertisement for a Gigabit port used to perform auto negotiation The syntax for this command is show port auto negotiation flowcontrol advertisement xmod num port num mod num Number of the switch port num Number of the port Output Example P330 N show port auto negotiation flowcontrol advertisement Port 1 1 advertises no flow control capabilities Port 1 2 advertises no flow control capabilities Port 1 3 advertises no flow control capabilities eto show trunk Usethe show trunk command to display VLAN tagging information of the ports port binding mode and the port VLAN ID The syntax for this command is show trunk lt mod_num gt lt port_num gt Output Example P330 N show trunk Port Mode Binding mode Native vlan 1 1 dotlg bound to configured vlans 1 1 2 dotlg bound to all vlans 1 1 3 off statically bound 1 1 4 off statically bound E 1 5 off statically bound l Avaya P332MF User s Guide 63 Chapter 6 CLI Layer 2 Output Example P330 N gt show trunk 1 5 Port Mode Binding mode Native vlan Vlans
4. The syntax for this command is show device mode Avaya P332MF User s Guide 49 Chapter 6 CLI Layer 2 show port Use the show port command to display port status The syntax for this command is show port lt mod_num gt lt port_num gt mod num Optional Number of the switch If you do not specify a number the ports on all switches are shown port num Optional Number of the port on the switch If you do not specify a number all the ports on the switch are shown You can also specify a range of ports separated by a dash e g 5 13 for ports 5 to 13 Output Example To display the status for port 4 on switch 3 P330 N show port 3 4 Port Name Status Vlan Level Neg Dup Spd Type 3 4 John connected 1 4 enable half 10M 100 1000Base Tx Show Port Output Fields Field Description Port Switch and port number Name The name you assigned to the port Status Status of the port connected no link disabled no Rmt Lnk VLAN VLAN ID of the port Level Priority level of the port 0 7 Neg The autonegotiation status of the port enable disable Duplex Duplex setting for the port fdx hdx Speed Speed setting for the port 10 100 50 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Type Port type for example For the P332 ML and P332GT ML switches 100BaseT 1000BaseT 1000BaseS For the P333T P334T P332MF P333R P333R LB switches 10BaseT 10BaseFL 100BaseTX 100BaseFX MM 100BaseFX SM 10 100BaseTX show
5. Port Mirroring Setting up port mirroring for ports in an Avaya P330 Switch Trap Managers Configuration Viewing and modifying the Trap Managers Table Switch Connected Addresses View devices connected to selected ports IP Multicast filtering with IGMP snooping new hardware Software support from s w 3 0 Hardware support from Hardware Ver C S 2 0 Port Security Intermodule Redundancy One pair per stack Also operates as a result of a module fault e g power failure System Requirements Minimum hardware and Operating System requirements are One of the following operating systems Windows 95 Windows 98 SP1 Windows 98 OSR Second Edition Windows ME Windows NT 4 Workstation or Server Windows 2000 Professional or Server Pentium II 400 Mhz based computer with 256 Mb of RAM 512 Mb recommended Minimum screen resolution of 1024 x 768 pixels Sun Microsystems Java plug in version 1 2 2 supplied Avaya P332MF User s Guide 139 Chapter 7 Installing the Embedded Web Manager e Microsoft Internet Explorer or Netscape Navigator CommunicatorO see table Table 7 1 Embedded Web Manager Browser Compatability Windows 95 or NT Windows 98 ME or 2000 Internet Explorer 5 0 or higher 5 01 or higher Netscape Navigator 4 7 4 73 Communicator Note for users of Netscape Navigator TheJ ava plug in requires certain services from
6. session router To configure the switch parameters on module 6 type the command session 6 switch e Note When you use the session command the security level stays the same Avaya P332MF User s Guide 33 Chapter 5 Avaya CLI Architecture Access amp Conventions Security Levels There are four security access levels User Privileged Configure and Supervisor e The User level is a general access level used to show system parameter values e The Privileged level is used by site personnel to access stack configuration options e The Configure level is used by site personnel for Layer 3 configuration e The Supervisor level is used to define user names passwords and access levels of up to 10 local users A login name and password are always required to access the CLI and the commands The login names and passwords and security levels are established using the username command Switching between the entities does not effect the security level since security levels are established specifically for each user For example if the operator with a privileged security level in the Switch entity switches to the Router entity the privileged security level is retained Entering the Supervisor Level The Supervisor level is the level in which you first enter Cajun Campus CLI and establish user names for up to 10 local users When you enter the Supervisor level you are asked for a Login name Type root as the Login n
7. P330 N clear dynamic vlans This command will delete all the vlans that were dynamically learned by the device do you want to continue Y N Avaya P332MF User s Guide 85 Chapter 6 CLI Layer 2 clear port static vlan clear cam clear log Use the clear port static vlan command to delete VLANS statically configured on a port The syntax for this command is clear port static vlan module port range vlan num module port Port range range vlan num The VLAN to unbind from the port Output Example P330 1 super clear port static vlan 1 10 5 VLAN 5 is unbound from port 1 10 Usethe clear cam command to delete all entries from the CAM table The syntax for this command is clear cam Output Example P330 N clear cam CAM table entry cleared Use the clear log command to delete the Log file of a switch The syntax for this command is clear log lt mod_num gt clear port mirror Use the clear port mirror command to cancel port mirroring The syntax for this command is clear port mirror lt source module gt lt source port gt lt dest module gt lt dest port gt 86 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Output Example P330 N clear port mirror 1 2 1 4 this command will delete the port mirror entry do you want to continue Y N y Mirroring packets from port 1 2 to port 1 4 is cleared clear secure mac Usethe clear secure mac comman
8. on lt name gt module prim port The primary port number module second port The secondary port number on Set the intermodule redundancy name The name of the fast redundancy default is fast Output Example P330 N gt set intermodule port redundancy 1 7 2 12 on backbone backbone port 2 12 is intermodule redundant to port 1 7 D Note You must disable Spanning Tree before you can enable redundancy Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york set intermodule port redundancy off Use the set intermodule port redundancy off command to clear the intermodule redundancy scheme The syntax for this command is set intermodule port redundancy off 108 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set port mirror Use the set port mirror command to define a port mirroring source destination pair in the stack The syntax for this command is set port mirror source port lt mod_num gt lt port_num gt mirror port mod num port num sampling always disable direction rxItx both always Keyword to activate the port mirroring entry disable Keyword to change the status of the port mirroring entry to not active rx Keyword to copy only incoming traffic tx Keyword to copy only outgoing traffic both Keyword to copy both incoming and outgoing traffic Output Example P330 N set port mirror source port 1 9 m
9. show autopartition module Example P330 N show autopartition 1 Mod Mode d Enable show dev log file show log Use the show dev log file command to display the encrypted device s log file Note This command is only supported by the P330 ML switches The syntax for this command is show dev log file Use the show log command to display an encrypted device s reset log This command is for Avaya technical support use The syntax for this command is show log module Output Example P330 1 super show log 1 MODULE 1 MESSAGE 01 00000000 0 05002966 0205 0000000000 MODULE 1 MESSAGE 02 Avaya P332MF User s Guide 67 Chapter 6 CLI Layer 2 00000000 0 00004242 0205 0000000000 MODULE 1 MESSAGE 03 00000000 0 00002395 0205 0000000000 show module identity Use the show module identity command to display the switch identity required for acquiring a license The syntax for this command is show module identity module Output Example show module identity module P330 1 super show module identity Mod Module Identity 1 1234567 2 4144162 show license Use the show license command to display a switch license The syntax for this command is show license mod_num mod_num The switch number Output Example P330 N gt show license 1 P330 N gt Module 1 License Mod Application License Key State Feature Flag 1 smon 0000 0000 0
10. 118 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Example P330 N set intelligent multicast client port pruning time 20 Done set intelligent multicast router port pruning time Usethe set intelligent multicast router port pruning time command to define aging time for router ports The syntax for this command is set intelligent multicast router port pruning time time time The time in seconds Example P330 N set intelligent multicast router port pruning time 20 Done set intelligent multicast group filtering delay time Usethe set intelligent multicast group filtering delay time command to define group filtering time delays The syntax for this command is set intelligent multicast group filtering delay time lt time gt time The time in seconds Example P330 N gt set intelligent multicast group filtering delay time 20 Done set secure mac Use the set secure mac command to add a unicast MAC address into the CAM table of a secured port This command is accessed only through connection to a particular switch not directly from the master switch e Note This command is not supported by the P332G ML and P332GT ML switches Avaya P332MF User s Guide 119 Chapter 6 CLI Layer 2 The syntax for this command is set secure mac lt mac address gt port mod num port num set security mode Usethe set security mode command to enable or dis
11. If autonegotiation mode is enabled for such ports the port s duplex mode is determined by autonegotiation and an error message is thus generated if you attempt to perform the set port duplex command in this case Note P332G ML and P332GT ML switch ports work in Full duplex mode only An error message is generated if you attempt to change P332G ML and P332GT ML ports to hal f duplex The syntax for this command is set port duplex mod num port num full half Example To set port 1 on module 2 to full duplex P330 N set port duplex 2 1 full Port 2 1 set to full duplex Avaya P332MF User s Guide 101 Chapter 6 CLI Layer 2 set port name set port trap set port vlan Usethe set port name to configure a name for a port If you do not specify a name the port name remains empty The syntax for this command is set port name lt mod_num gt lt port_num gt lt name gt name Name assigned to the port Output Example P330 N set port name 1 2 arthur Port 1 2 name set Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Usethe set port trap command to enable disable generic SNMP uplink downlink traps from a port The syntax for this command is set port trap mod num port num enable disable Output Example P330 N4 set port trap 1 2 enable Port 1 2 up down trap enabled Use the s
12. Note Functions operate in their default settings unless configured otherwise Avaya P332MF User s Guide 27 Chapter 4 Installation and Setup Cabling Avaya P330 modules include the following types of ports according to the speed and standard they support 10Base T 100Base TX 100Base FX 1000Base SX and 1000Base LX Note To interconnect Avaya P330 switches with twisted pairs crossed cables are required e The maximum UTP cable length connected to a 10 100 Mbps port operating as 10Base T is 100 m 328 ft e A UTP Category 5 cable must be connected to any 100Base TX port via an RJ45 connector The maximum UTP cable length connected to a 10 100 Mbps port operating as 100Base TX is 100 m 328 ft e A fiberoptic cable must be connected to any 100Base FX port via a pair of SC connectors The maximum fiber cable length connected to a 100Base FX port is 412 m 1 352 ft when operating in half duplex and 2 km 6 562 ft when operating in full duplex e The maximum length of fiber optic cable connected to a 12 fiber MT RJ port is 2 km 6 562 ft Appropriate cables are available from your local supplier Table 4 3 Gigabit Ethernet Cabling GE See Diameter S dth se Ge Wavelength ype qua MhzKm m m EEN 1000BASE SX MM 62 5 160 220 2 850 1000BASE SX MM 62 5 200 275 2 850 1000BASE SX MM 50 400 500 2 850 1000BASE SX MM 50 500 550 2 850 1000BASE LX MM 62 5 500 550 2 1
13. X330 OC12Fl 500m Multimode fiber can also be OC 3 reduced range e X330 0C1251 15 km Single mode fiber can also be OC 3 The ATM Modules can be installed in the following Avaya P330 Family switches e Avaya P333T Hardware Version C S 1 3 and higher with Embedded S W 2 4 and higher Note The ATM Expansion Module cannot be used in Avaya P333T hardware Versions lower than C S 1 3 e Avaya P334T Embedded S W Ver 2 4 and higher e Avaya P332MF Embedded S W Ver 3 0 and higher e Avaya P333R Embedded S W Ver 2 4 and higher Refer to the Avaya X330 ATM Access Module Installation Guide for installation procedures The multimode Avaya X330 OC12F1 and X330 OC3F1 future ATM Modules are Class 1 LED products The single mode X330 0C1251 ATM Module is a Class 1 Laser product They comply with EN 60825 1 and Food and Drug Administration FDA 21 CFR 1040 10 and 1040 11 The Modules must be operated under recommended operating conditions Safety Information Single mode Module Laser Classification CLASS 1 LASER PRODUCT Note Class 1 lasers are inherently safe under reasonably foreseeable conditions of operation Caution The use of optical instruments with this product will increase eye hazard Avaya P332MF User s Guide 155 Appendix A Specifications Multi Mode Module LED Warning The following warnings apply to the X330 ATM Modules equipped with multi mode fiber Class 1 LED Product
14. set radius authentication server clear radius authentication server set radius authentication retry time set radius authentication retry number set radius authentication udp port Enables secret authentication for the Avaya P330 unit Sets a primary or secondary RADIUS server IP address Removes a primary or secondary RADIUS authentication server Sets the time to wait before re sending an access request Sets the number of times an access request is sent when there is no response Sets the RFC 2138 approved UDP port number EW archive Page 133 Page 133 Page 133 Page 134 Page 134 Page 134 132 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set radius authentication secret Usethe set radius authentication secret command to enable secret authentication for the P330 unit The syntax for this command is set radius authentication secret string string text password Example P330 N super set radius authentication secret sodot set radius authentication server Use the set radius authentication server command to set a primary or secondary RADIUS server IP address The syntax for this command is set radius authentication server lt ip address gt lt primary secondary gt ip addr IP address of the RADIUS authentication server primary default Primary authentication server secondary Secondary authentication server Example P330 N supe
15. the initial prompt shows the number of the Master module in the Avaya P330 stack For example if the stack Master is Module 5 counting from the bottom up then the prompt is P330 5 gt In this document the Module number in the prompt is generic and is represented by NDS If you wish to open a session with an Avaya P333R LB routing module in the stack or reopen a session with the M aster module usethe session command see below The command prompt is nat hierarchical in structure If you wish to use several commands each beginning with the same keyword you must retype all parts of the command each time For example if after you want to set the system contact and the system name you musttype both set system contact and set system name However you can use command abbreviations Avaya P330 Sessions You can use sessions to switch between P330 modules or to switch between Layer 2 and Layer 3 commands in the P333R CLI To switch between P330 modules use the command session mod num mode The mod num is the number of the module in the stack counting from the bottom up The mode can be either switch or router When Module Number is not specified the command switches between the modes in the local module Use switch mode to configure layer 2 commands Use router mode to configure routing commands Examples To configure router parameters in the module that you are currently logged into type the following command
16. 12 enable 52 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show intermodule port redundancy Usethe show intermodule redundancy command to display the intermodule redundancy entry defined for the stack The syntax for this command is show intermodule port redundancy Output Example P330 N show intermodule port redundancy Primary Port 1 1 Primary Port status Disable Secondary Port 1 2 Secondary Port status Disable show port mirror Use the show port mirror command to display mirroring information for the stack The syntax for this command is show port mirror mod num port num Output Example P330 N show port mirror port mirroring Mirroring both Rx and Tx packets from port 1 2 to port 1 4 is enabled show port vlan binding mode Usethe show port vlan binding mode command to display port vlan binding mode information The syntax for this command is show port vlan binding mode module port module port The switch number the port number Avaya P332MF User s Guide 53 Chapter 6 CLI Layer 2 Output Example P330 N gt show port vlan binding mode port 1 1 is statically bound port 1 2 is statically bound port 1 3 is statically bound port 1 4 is statically bound port 1 6 is statically bound port 1 7 is statically bound port 1 8 is statically bound S S S S port 1 5 is statically bound S S S S port 1 9 is statically bound port 1 10 is s
17. 135 show port mirror 53 show port redundancy 52 show port security 54 show port self loop discovery 57 show port trap 51 show port vlan binding mode 53 show ppp authentication 72 show ppp baud rate 73 show ppp configuration 73 show ppp incoming timeout 73 show ppp session 72 show radius authentication 136 show rmon alarm 71 show rmon event 72 show rmon history 71 show rmon statistics 70 show secure mac port 77 show security mode 76 show self loop discovery 78 show snmp 47 show snmp retries 48 show snmp timeout 48 show spantree 65 show system 69 show tftp download software status 74 show tftp download upload status 74 show time 45 show timeout 48 show timezone 45 show timezone parameters 45 show trunk 63 show username 136 show vlan 64 show web aux files url 75 sync time 123 Avaya P332MF User s Guide Index of CLI Commands 162 Avaya P332MF User s Guide How to Contact Us To contact Avaya s technical support please call In the United States Dial 1 800 237 0016 press 0 then press 73300 In the EMEA Europe Middle East and Africa Region Local Dial In Local Dial In Country Number Albania 31 70 414 8001 Austria 43 1 36 0277 1000 Azerbaijan 31 70 414 8047 Bahrain 800 610 Belgium 32 2 626 8420 Belorussia 31 70 414 8047 Bosnia 31 70 414 8042 Herzegovina Bulgar
18. A Specifications MTBF in Various Configurations The following table provides the MTBF for the Avaya P333T PWR P332MFin various configurations Table B Z MTBF for the Avaya P332MF in Various Configurations Model Without BUPS With BUPS Without With Without With X330STK X330STK X330STK X330STK P332MF 163 995 140 766 242 000 200 000 P332MF X330T16 137 893 121 080 186 000 159 000 P332MF X330F2 133 227 117 467 178 000 154 000 P332MF X330L2 125 298 111 259 165 000 144 000 X33052 P332MF X330L1 gt 125 298 gt 111 259 gt 165 000 gt 144 000 X330S1 P332MF X330G2 128 568 113 830 168 000 149 000 P332MF X330GT2 137 571 120 831 186 000 160 000 158 Avaya P332MF User s Guide Index of CLI Commands clear cam 86 clear dynamic vlans 85 clear log 86 clear port mirror 86 clear port static vlan 86 clear radius authentication server 133 clear screen 41 clear secure mac 87 clear snmp trap 84 clear timezone 84 clear vlan 85 copy module config tftp 129 copy stack config tftp 128 copy tftp EW_archive 131 copy tftp module config 130 copy tftp stack config 130 copy tftp SW_image 131 dir 79 dir 79 get time 123 hostname 83 no hostname 82 no rmon alarm 82 no rmon event 83 no rmon history 82 no username 135 nvram initialize 125 ping 41 reset 124 reset mgp 125 reset stack 124 rmon alarm 127 rmon event 128 rmon history 126 session 40 set allowed
19. BUPS Connector D Power Supply Connector Cable to Cable to Lower Unit Upper Unit BUPS Connector D Power Supply Connector 22 Avaya P332MF User s Guide Chapter4 Installation and Setup Figure 4 3 Avaya P330 Stack Connections X330RC X3305C X330LC Avaya P332MF User s Guide 23 Chapter 4 Installation and Setup Installing Expansion Sub modules v Caution The expansion sub modules contain components sensitive to electrostatic discharge Do not touch the circuit board unless instructed to do so Installing the Expansion Sub module into the Avaya P330 1 Remove the blanking plate or other sub module if installed 2 Insert the sub module gently into the slot ensuring that the Printed Circuit Board PCB is aligned with the guide rails The PCB not the metal base plate fits into the guide rail 3 Firmly press the sub module until it is completely inserted into the Avaya P330 4 Gently tighten the two screws on the front panel of the expansion sub module by turning them Removing an Existing Expansion Sub module 1 Loosen the screws by turning the kno
20. If no switch number is defined or the switch number of the Master is defined the command resets the entire system If the switch number is defined the command resets the specified switch only Note You should perform a reset after downloading software to the switch The syntax for this command is reset module number Output Example To reset the Master agent and force the entire system to reset P330 N reset This command will force a switch over to the master module and disconnect your telnet session Do you want to continue y n n y Connection closed by foreign host Output Example To reset switch 4 P330 N reset 4 This command will reset module 4 and may disconnect your telnet session Do you want to continue y n n y Resetting module 4 reset stack Use the reset stack command to perform a hardware reset in the entire stack The syntax for this command is reset stack 124 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 reset mgp Use the reset mgp command to perform a software reset in the G700 Media Gateway Processor The syntax for this command is reset mgp reset wan Use the reset wan command to perform a software reset in the X330 WAN Access Router Module The syntax for this command is reset wan module number bank a module Optional the module number where the WAN module to be number reset resides bank a Optional boot the WAN module from bank a after r
21. P330 is 2U 88mm 3 5 high Place the Avaya P330 in the rack as follows 1 Snap open the hinged ends of the front panel to reveal the fixing holes 2 Insert the unit into the rack Ensure that the four Avaya P330 screw holes are aligned with the rack hole positions as shown in Figure 4 1 Figure 4 1 Avaya P330 Rack Mounting Ja Dadi Jaja Jaa Jajan Dev nen pen sr E m Li F Lj gt z Li Li e Li C LI Ci ILI CO KEY A Hole in rack e Screw position 3 Secure the unit in the rack using the screws Use two screws on each side Do not overtighten the screws 4 Snap closed the hinged ends of the front panel 5 Ensure that ventilation holes are not obstructed 20 Avaya P332MF User s Guide Chapter 4 Installation and Setup Connecting Stacked Switches Note The two ends of the Octaplane cable terminate with different connectors Each connector can only be connected to its matching port The following cables are used to connect stacked switches Short Octaplane cable X3305C ivory colored used to connect adjacent switches Catalog No CB0223 or switches separated by a BUPS unit Long Extra Long Octaplane cable X330LC X330L LC ivory colored used to connect switches from two different physical stacks or switches separated by a BUPS unit Catalog No CB0225 CB0270 Redundant Long Redundant Octaplane cable X330RC X330L RC black used to connect t
22. at the same value as the host The syntax for this command is set ppp baud rate 9600 19200 38400 Example P330 N set ppp baud rate 38400 Avaya P332MF User s Guide 117 Chapter 6 CLI Layer 2 set web aux files url Use the set web aux files url command to allow the Device Manager to automatically locate the URL the http www address and path of the Web server containing the Device Manager help files and Java plug in Note Ensure that the Web server is always accessible otherwise Web access to the device may take a few minutes The syntax for this command is set web aux files url lt IP address directory name Example P330 N4 set web aux files url 192 168 47 25 emweb aux files Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york set intelligent multicast Usethe set intelligent multicast command to enable or disable the IP multicast filtering application The syntax for this command is set intelligent multicast enable disable Example P330 N set intelligent multicast enable Done set intelligent multicast client port pruning time Usethe set intelligent multicast client port pruning time command to define aging time for client ports The syntax for this command is set intelligent multicast client port pruning time time time The time in seconds
23. copy stack config tftp c conf cfg 192 168 49 10 Beginning upload operation 128 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 This operation may take a few minutes Please refrain from any other operation during this time For more information use upload status command Dk ck ck ck Ck ck ck CK Ck kk ck Ck ck ck Ck ck kk ck Ck ck ck Ck ck ck ck ck ck ck ck ck ck ck ck ck kk ck ck ehh kk heh h ck ck Sk ck ko hk kk ko ko ko If you are currently running the P330 Device Manager application it is recommended to exit from it before performing configuration download operations kk ck ck ck ck ck ck ck Sk ck Ck KKK KKK KKK KKK ck kk Ck ck ck kk ck kk ck KKK KKK KKK KKK KKK ko kk kk kk ko Sk KKK ko kc KK copy module config tftp Usethe copy module config tftp command to upload the switch level parameters from the current NVRAM running configuration into a file via TFTP If an error occurred during upload you can check this using the command show tftp upload status you must fix the problem The following is a list of possible problems a You did not create an empty text file at the destination server 0 Bytes b You do not have the correct path to the file c The destination server is not active on d The destination server is unreachable Then perform the upload procedure again twice as follows a Delete the destination file and recreate a correctly named empty file at the destination server 0 Bytes Type
24. ft A 50 mm or 62 5 mm multimode MMF fiber cable may be connected to a 1000Base LX GBIC port The maximum length is 550 m 1 804 ft for 50 mm and 62 5 mm cable The LX transceiver has a Wavelength of 1300 nm Transmission Rate of 1 25 Gbps and Input Power of 5V X330G2 SX GBIC Transceiver A 50 um or 62 5 um multimode MMF fiber cable may be connected to a 1000Base SX GBIC port The maximum length is 500 m 1 640 ft for 50 um cable and 220 m 722 ft for 62 5 um cable The SX transceiver has a Wavelength of 850 nm Transmission Rate of 1 25 Gbps and Input Power of 5V 152 Avaya P332MF User s Guide Appendix A Specifications Agency Approval The transceivers comply with e EMC Emission US FCC Part 15 Subpart B Class A Europe EN55022 class A e Immunity EN50082 1 e Safety UL for US UL 1950 Std C UL UL for Canada C22 2 No 950 Std Food and Drug Administration FDA 21 CFR 1040 10 and 1040 11 and CE for Europe EN60950 Std Complies with EN 60825 1 MTBF The Mean Time Between Failures MTBF for the X330G2 Expansion Sub module is 594 639 hours X330GT2 Gigabit Ethernet Expansion Module The X330GT2 Expansion Module provides two copper Gigabit Ethernet 1000Base T ports Note The X330GT2 module is only supported by Avaya P330 embedded software versions 2 4 and higher Installing the Expansion Module in the Avaya P330 1 Remove the blanking plate or other Module if installed 2 I
25. gt P330 1 super show tftp download software status odule 1 odule Source file Destination file 1 d p340sw gt m1 3 5 18 p340 web EW_Archive Host Running state Failure display Last warning 149 49 70 61 Writing null No warning 74 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show web aux files url Use the show web aux files url command to display the URL Directory from where the P330 can access the Device Management auxiliary files for example help files The syntax for this command is show web aux files url show intelligent multicast Use the show intelligent multicast command to display the intelligent multicast configuration The syntax for this command is show intelligent multicast Output Example P330 N show in telligent multicast Intelligent multicast configuration intelligent multicast stat Disabled Intelligent multicast client port pruning time 600 Sec Intelligent multicast router port pruning time 1800 Sec intelligent multicast group filtering delay time 10 Sec Intelligent multicast HW configuration Module 1 No IPMc Support Not Installed Sub Module Cascade No IPMc Support Avaya P332MF User s Guide 75 Chapter 6 CLI Layer 2 show intelligent multicast hardware support Use the show intelligent multicast hardware support command to display the in
26. gt show port blocking Port Blk Fwd 1 Blocking 2 Blocking 3 Blocking 4 Blocking 5 Blocking 6 Blocking 7 Blocking 8 Blocking 9 Blocking 10 Blocking 11 Blocking 12 Forwarding 13 Blocking 14 Blocking 15 Blocking 16 Blocking 17 Blocking 18 Blocking 19 Blocking 20 Blocking 21 Blocking 22 Blocking 23 Blocking 24 Forwarding 56 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show port self loop discovery Use the show port self loop discovery command to display which port or switch has an enabled IBM token ring cable loop discovery status Gi Note This command is not supported by the P330 ML switches Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch The syntax for this command is show port self loop discovery module num port number Output Example P330 N gt show port self loop discovery 1 5 Self Loop Discovery is enabled on port 1 5 show internal buffering The show internal buffering command displays the size options Maximum Minimum or Medium of the Receive Rx buffer allocated to each port of the specified switch The syntax for this command is show internal buffering lt mod_num gt Output Example P330 N gt show internal buffering 1 Module Internal Buffer 1 med Note Internal buffering for the P330 ML switches will always have the value Not supported This comma
27. is set interface ppp lt ip_addr gt lt net mask gt ip_addr IP address used by the P330 to connect via its PPP interface net mask Subnet mask used by the P330 to connect via its PPP interface Output Example P330 N gt set interface ppp 149 49 34 125 255 255 255 0 Interface ppp has its ip address set You can also use the set interface ppp command to enter modem mode enter terminal mode disconnect the PPP session or to reset the connected modem The syntax for this command is set interface ppp enablelenable always disableloff reset enable Enable PPP and enter modem mode enable always Enable automatic reentry into modem mode after modem cable disconnection or reconnection disable Disable PPP and enter terminal mode off Disconnect the active PPP session reset Reset the connected modem Output Example P330 N gt set interface ppp reset PPP has reset the connected modem 98 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set port level Output Example P330 N set interface ppp enabl Entering the Modem mode within 60 seconds Please check that the proprietary modem cable is plugged into the console port Output Example P330 N set interface ppp disable Entering the Terminal mode immediately Usethe set port level command to set the priority level of a port Untagged without an 802 1p priority header packets travelling through ports set with priority 0
28. port trap Usethe show port trap command to display information on SNMP generic link up down traps sent for a specific port The syntax for this command is show port trap mod num port num Output Example P330 N show port trap 1 1 Port 1 1 up down trap is disabled show port channel Usethe show port channel command to display Link Aggregation Group LAG information for a specific switch or port The syntax for this command is show port channel lt mod_num gt lt port_num gt Output Example show port channel 1 Port Channel Status Channel Name 1 1 off 1 2 off 1 3 on serverl 1 4 on serverl 1 5 off Guy Avaya P332MF User s Guide 51 Chapter 6 CLI Layer 2 show port classification Use the show port classification command to display a port s classification The syntax for this command is show port classification module port module port The switch number the port number Output Example P330 1 super show port classification Port Port Classification IX regular 1 2 regular 17 3 regular 1 4 regular 1 5 regular 1 6 regular 1477 regular QUO E show port redundancy Usethe show port redundancy command to display information about all redundancy schemes defined for this stack The syntax for this command is show port redundancy Output Example P330 N show port redundancy Redundancy Name Primary Port Secondary Port Status uplink 1 7 2
29. retries ENEE 48 show snmp timeouts ai dene dee tetris 48 Show meonta 5t SNN RR SNN aa 48 show logout kotamu Aa tret aee e AA Hain 48 SNOW terrateniente 49 show device mode conooccocccooncconnoconanonnonancconncnnnocnnonnnocnnnconncnnno a a ieies 49 SNOW ee GE 50 SHOW POrt trap cles A eere emi eter E 51 show port channel tret rte ree rre 51 Show port classification EE 52 show port redundancy ENEE 52 show intermodule port redundancy sss 53 SHOW ele Oe EE 53 show port vlan binding mode eee 53 Show port Seeuriby si se ee Pesce ANE NAN REP ane 54 show port blocking dimana terree 55 show port self loop discovery ENEE 57 show internal buffering ENEE 57 showbootbank 5 tete te aei daneben tenis 58 show module eph ette Ee e to Pee pe BNN 58 show port tlowcoritrol erento nire erret eerte dentes 60 SHOW CAM fd uet cet des iei do as His HO tet Pet iie Sen 62 show cascading fault monitoring sss 62 show port auto negotiation flowcontrol advertisement 63 SHOW e Ee e oo E 63 SNOW lans etre eee eth sees E aa n 64 show leakyevlani ere 65 SHOW SPA rn eee AA e He deett ette 65 show AULOP Art HOM a evan temer ere mri rte eres 67 show dey log file nci tete eei oe fas 67 Ee 67 show module identity ENEE 68 SHOW license cease cero roter ertt eere pietre ote ces eel even nun 68 Show System s nne et pede tede ese aa 69 SHOW timor statisties eter pese tester de
30. the command copy module config tftp for the first time c Delete the destination file and recreate a correctly named empty file at the destination server 0 Bytes d Type the command copy module config tftp again a second time The syntax for this command is copy module config tftp filename ip mod num filename The file name full path ip The IP address of the TFTP server mod num The switch number Output Example P330 N copy module config tftp c config switchl cfg 192 168 49 10 5 Beginning upload operation This operation may take a few minutes Please refrain from any other operation during this time Avaya P332MF User s Guide 129 Chapter 6 CLI Layer 2 For more information use show tftp upload status command kc ck ck ck ck ck ck Ce KKK KKK KKK KKK KKK KKK KK KKK KK KR KKK KKK KKK KKK KKK KK KKK KKK KKK KKK KKK If you are currently running the P330 Device Manager application it is recommended to exit from it before performing configuration download operations ZS kk ck ck ck ck ck ck KK ck Ck Sk KKK ck kk KK ck ck ck KK KKK KKK KK Ck ck KKK KKK KKK kk ck kk kk Sk kk kk ko KKK KKK KK copy tftp stack config Usethe copy tftp stack config command to download the stack level configuration from a saved file into the current NVRAM running configuration via TFTP To use this command you need to have an active tftp server and to create a file into which to download
31. the data If Avaya Multi Service Network Manager is running an additional TFTP server is not required Note You should perform the nvram initialize command prior to the copy tftp operation The syntax for this command is copy tftp stack config filename ip filename The file name full path ip The IP address of the TFTP server Example P330 N4 copy tftp stack config c config switchl cfg 192 168 49 10 copy tftp module config Use the copy tftp module config command to download the switch level configuration from a saved file into the current NVRAM running configuration of a switch via TFTP To use this command you need to have an active tftp server and to create a file into which to download the data If Avaya Multi Service Network Manager is running an additional tftp server is not required Note You should perform the nvram initialize command prior to the copy tftp operation 130 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 The syntax for this command is copy tftp module config filename ip filename The file name full path ip The ip address of the TFTP server Example P330 N copy tftp module config c config switchl cfg 192 168 49 10 5 copy tftp EW_archive Use the copy tftp EW_archive command to download the P330 Device Manager application into the switch via TFTP To use this command you need to have an active TFTP server and to create a file i
32. three screws in the terminal block is M3 5 3 The pitch between each screw is 9 5mm Warning Before performing any of the following procedures ensure that DC power is OFF Y Caution This product is intended for installation in restricted access areas and is approved for use with 18 AWG copper conductors only The installation must comply with all applicable codes 4 Connect the power cable to the DC power supply a Warning The proper wiring sequence is ground to ground positive to positive and negative to negative Always connect the ground wire first and disconnect it last Avaya P332MF User s Guide 25 Chapter 4 Installation and Setup Configuring the Switch The Avaya P330 may be configured using the text based Command Line Interface CLI the built in Avaya P330 Device Manager Embedded Web or Avaya Multi Service Network Manager For instructions on the text based utility see the CLI chapter For instructions on installation of the graphical user interfaces see the Avaya P330 Device Manager Appendix For instructions on the use of the graphical user interfaces refer to the Device Manager User s Guide on the Documentation and Utilities CD Avaya P330 Default Settings The default settings for the Avaya P330 switch and its ports are determined by the Avaya P330 software These default settings are subject to change in newer versions of the Avaya P330 software See the Release Notes
33. version can beabbreviated ver For ambiguous commands type the beginning letters on the command line and then use the Tab key to toggle through all the possible commands beginning with these letters 36 Avaya P332MF User s Guide Chapter 5 Avaya CLI Architecture Access amp Conventions Universal Commands Universal commands are commands that can be issued anywhere in the hierarchical tree Top and Up commands The Up command moves you up to the next highest level in the CLI command hierarchy The Top command moves you to the highest level Retstatus command Usethe retstatus command to show whether the last CLI command you performed was successful It displays the return status of the previous command The syntax for this command is retstatus Output Example P330 set port negotiation 2 4 disable Link negotiation protocol disabled on port 2 4 Tree command The tree command displays the commands that are available at your current location in the CLI hierarchy The syntax for this command is tree Avaya P332MF User s Guide 37 Chapter 5 Avaya CLI Architecture Access amp Conventions 38 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 This chapter provides all the Layer 2 CLI commands parameters and their default values The CLI is command line driven and does not have any menus To activate a configuration option you must type the desired command at the prompt a
34. when performing flowcontrol autonegotiation advertisement show trunk Displays VLAN tagging information of Page 63 the ports port binding mode and the port VLAN ID show vlan Displays the VLANs configured in the Page 64 stack switch show leaky vlan Displays the leaky VLAN status Page 65 show spantree Shows Spanning Tree Protocol STP Page 65 settings show autopartition Shows the autopartition settings Page 67 show dev log file Displays the encrypted device log file Page 67 show log Displays an encrypted device reset log Page 67 show module Displays the switch s identity Page 68 identity show license Shows the license Page 68 show system Shows system parameters Page 69 e show rmon statistics Shows the traffic statistics of an interface Page 70 show rmon history Shows the existing history entries Page 71 show rmon alarm Shows the existing alarm entries Page 71 Avaya P332MF User s Guide 43 Chapter 6 CLI Layer 2 show rmon event Shows the existing event entries Page 72 show ppp session Shows the PPP parameters of the active Page 72 PPP session show ppp Shows the authentication method used Page 72 authentication for PPP sessions show ppp incoming Shows the amount of time PPP sessions Page 73 timeout can remain idle before being disconnected show ppp baud rate Shows the baud rate Page 73 show ppp Displays the ppp configuration Page 73 configuration show tftp upload Shows the status of the TF
35. 0 stack For a full description of the SMON routing License and the installation procedure please refer to the Installation Guide provided with the SMON routing License The syntax for this command is set license module license featureName module The switch number license The license number featureName The name of the feature either smon or routing Example P330 N set license 1 021 1ad bad ca5 8d2 ccd smon 116 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set ppp authentication incoming Usetheset ppp authentication incoming command to define the authentication method used for a PPP server or client session The syntax for this command is set ppp authentication incoming pap chap none pap PAP authentication method chap CHAP authentication method none No authentication Example P330 N super set ppp authentication incoming chap set ppp incoming timeout Usethe set pppincoming timeout command to configure the number of minutes until the system automatically disconnects an idle PPP incoming session The syntax for this command is set ppp incoming timeout lt time gt time The timeout in minutes Output Example P330 N set ppp incoming timeout 15 PPP incoming session will automatically disconnect after 15 minutes of idle time set ppp baud rate Use the set ppp baud rate command to define the baud rate used in PPP sessions Note that the peer baud rate must be set
36. 000 0000 0000 0000 licensed 1 68 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show system Usethe show system command to display the up time system name location and contact person The syntax for this command is show system Output Example P330 N show system Uptime d h m s 0 2 40 55 System Name System Location System Contact P332 version 3 0 5 Alpha LAB Ygdal Naouri Switch MAC address 00 40 Od 8a 04 b4 Avaya P332MF User s Guide 69 Chapter 6 CLI Layer 2 RMON Tools The following are a series of RMON commands however we recommend using the P330 Device Manager show rmon statistics Use the show rmon statistics command to show the RMON statistics counters for a certain interface number according to the MIB 2 interface table numbering scheme The syntax for this command is show rmon statistics lt module port gt module port range of ports the defaultis full switch Output Example P330 1 super show rmon statistics Statistics for switch is active owned by Monitor Received 171665151 octets 1474442 packets 1030346 broadcast and 369540 multicast packets 0 undersize and 0 oversize packets 1 fragments and 0 jabbers 11 CRC alignment errors and 0 collisions of dropped packet events due to a lack of resources 0 of packets received of length in octets 64 862274 65 127 973110 128 255 173921 256 511 72880 512 1023 4374 1024 1518 29744
37. 1000Base SX X330L2 2 1000Base LX X33081 1 1000Base SX X330L1 1 1000Base LX Laser Safety The Avaya X330S1 S2 multi mode transceivers and the Avaya X330L1 X330L2 single mode transceivers are Class 1 laser products They comply with IEC 825 1 and Food and Drug Administration FDA 21 CFR 1040 10 and 1040 11 The transceivers must be operated under recommended operating conditions Avaya P332MF User s Guide Appendix A Specifications Laser Classification CLASS 1 LASER PRODUCT Note Class 1 lasers are inherently safe under reasonably foreseeable conditions of operation Caution The use of optical instruments with this product will increase eye hazard q Usage Restriction The optical ports of the module must be terminated with an optical connector or a dust plug when not in use Laser Data Avaya P330S2 Expansion Modules Wavelength 850 nm Output power dissipation Max 0 63W Transmit power Min 9 dbm Max 4 dbm Receive power Min 17 dbm Max 0 dbm Avaya P330L1 2 Expansion Modules Wavelength 1300 nm Output power dissipation Max 0 68W Transmit power 9 um SME Min 9 5 dbm Max 3 dbm Transmit power 62 5 um and 50 um MMF Min 11 5 dbm Max 3 dbm Receive power 9 um SMF 62 5 um and 50 um MMF Min 20 dbm Max 3 dbm Avaya P332MF User s Guide 149 Appendix A Specifications Fast Ethernet Fiber Expansion Module Table A 3 Fiber Fast Ethernet Expansion
38. 2 Avaya P330 stacks with an Avaya 330 backbone Avaya P330 Avaya P330 EE e 10 100 Mbps Ethernet Gigabit Ethernet with LAG Avaya P332MF User s Guide Chapter2 Applications Application 3 This application shows Avaya P880 as the network backbone with Avaya P332MF deployed as a distribution switch An Avaya P333R multilayer switch provides local IP routing The Avaya P333T stacks act as closet devices with LAG and redundant links Figure 2 3 Avaya P332MF with an Avaya P882 backbone 10 100 M bps Ethernet LAG Redundancy 10 100 Mbps 100 Mbps p Ethernet Fiber Optic Ethernet with LAG 10 100 Mbps Ethernet Avaya P333R Server Farm Gigabit Ethernet with LAG ze Avaya P882 4x100 Mbps LAG Avaya P332MF User s Guide 7 Chapter 3 Avaya P332MF Front and Back Panels Avaya P332MF Front Panel The Avaya P332MF front panel contains LEDs controls connectors and an expansion Module slot as well as a console connector The status LEDs and control buttons provide at a glance information The front panel LEDs consist of Port LEDs and Function LEDs The Port LEDs display information for each port according to the illuminated function LED The function is selected by pressing the left or right button until the desired parameter LED is illuminated For example if
39. 3 LAG member 20 128 4 LAG member 20 128 5 not connected 20 128 6 not connected 20 128 OUO Avaya P332MF User s Guide 65 CLI Layer 2 Output Fields Field Spanning tree Designated Root Designated Root Priority Designated Root Cost Designated Root Port Root Max Age Hello Time Bridge ID MAC ADDR Bridge ID Priority Port State Cost Priority Description Status of whether Spanning Tree Protocol is enabled or disabled MAC address of the designated spanning tree root bridge Priority of the designated root bridge Total path cost to reach the root Port through which the root bridge can be reached shown only on nonroot bridges Amount of time a BPDU packet should be considered valid Number of times the root bridge sends BPDUs Bridge MAC address used in the sent BPDUs Bridge priority Port number Spanning tree port state disabled inactive not connected blocking listening learning forwarding bridging or type pvid inconsistent Cost associated with the port Priority associated with the port Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show autopartition Use the show autopartition command to display the automatic partition Note Autopartition for the P330 ML switches will always have the value disabled This command is used to display the autopartition status for the other P330 switches in the stack The syntax for this command is
40. 3 will be served only after packets traveling through ports set with priority 4 7 in case of congestion Packets arriving with an 802 1p priority header will not be modified by this command The syntax for this command is set port level lt mod_num gt lt port_num gt value value Priority level 0 7 Output Example To set the priority level for port 2 on module 1 to 7 P330 N set port level 1 2 7 Port 1 2 port level set to 7 set port negotiation Usethe set port negotiation command to enable or disable autonegotiation on a port If autonegotiation is disabled you can set port parameters using the relevant CLI commands If autonegotiation is enabled these commands have no effect For Fiber Gigbit Ethernet ports it can determine the flow control pause mode only Note Copper ports in the P332GT ML can work at 1000Mbps Full Duplex only if autonegotiation is enabled on both cable ends and you are using a 4 pair 8 wires Ethernet cable If autonegotiation is disabled these ports can only work at 100Mbps Full Duplex and autonegotiation should be disabled on both cable ends Avaya P332MF User s Guide 99 Chapter 6 CLI Layer 2 The syntax for this command is set port negotiation lt mod_num gt lt port_num gt enable disable Output Example To disable autonegotiation on port 1 module 4 P330 N4 set port negotiation 4 1 disable Link negotiation protocol disabled on port 4 1 set port
41. 30 is fully compliant with IEEE standards for VLAN Tagging Gigabit Ethernet Spanning Tree and Flow Control This full standards compliance combined with auto negotiation for 10 100 1000 Mbps and half full duplex facilitates the expansion of your network to match your company s growing needs Avaya P330 Family Features e You can connect up to 10 Avaya P330 switches in a stack Moreover this stack can be either in one rack or split over several racks using the X330LC Long Cable according to your requirements e Avaya X330STK this stacking Module is used to connect Avaya P330 switches in a stack via the Octaplane e Avaya P330 BUPS this back up power supply module supports up to four Avaya P330 switches e One RJ 45 RS232 front panel console connector for both terminal and modem sessions e Two fan units in every switch with operation sensors e One virtual IP address for managing the whole stack the P330 stack is managed as a single entity e Hot swapping of one switch at a time by activation of the redundant cable Does not disrupt the operation of other Avaya P330 switches Does not change stack configuration Does not require network downtime e Connection through Telnet from the front panel ports of any switch with multiple levels of password protection login and inactivity timeouts Avaya P332MF User s Guide 1 Chapter 1 Avaya P330 Overview Avaya P330 Standards Supported The Avaya P330 compl
42. 310 1000BASE LX MM 50 400 550 2 1310 1000BASE LX SM 9 NA 10 000 2 1310 28 Avaya P332MF User s Guide Chapter 4 Installation and Setup Connecting the Console Cable The Avaya P330 has one serial port on the front panel of the switch for connecting a terminal a terminal emulator or a modem The serial port on the front panel is labelled Console and has a RJ 45 connector Connect the P330 to a terminal or a terminal emulator using the supplied console cable and the RJ 45 to DB 9 adaptor To connect a modem use the supplied cable and an RJ 45 to DB 25 adaptor Note The cable and two adaptors can be found in the accessory set and they are clearly marked Configuring the Terminal Serial Port Parameters Connecting a The serial port settings for using a terminal or terminal emulator are as follows e Baud Rate 9600 bps e Data Bits 8 bits e Parity None e Stop Bit 1 e Flow Control None e Terminal Emulation VT 100 Modem to the Console Port A PPP connection with a modem can be established only after the Avaya P330 is configured with an IP address and net mask and the PPP parameters used in the Avaya P330 are compatible with the modem s PPP parameters 1 Connect a terminal to the console port of the Avaya P330 switch as described in Connecting the Console Cable on page 29 2 When you are prompted for a Login Name enter the default name root 3 When you
43. 4 seconds All LEDs on stack light up until buttons are released FIV Force Initial Version boot from backup initial version of the Avaya P330 software from Bank A see Note below 10 Avaya P332MF User s Guide Chapter 3 Avaya P332MF Front and Back Panels Note To perform Force Initial Version reset the module and at the same time press the FIV reset button use an opened paper clip or other pointed object Release the reset buttons first and 1 or 2 seconds later release the FIV button Note The Port LEDs of the P332MF are numbered from 1 12 Expansion Module ports are numbered from 51 Port LED numbers 49 50 are reserved Avaya P332MF User s Guide 11 Chapter 3 Avaya P332MF Front and Back Panels Avaya P330 Back Panel The Avaya P330 back panel contains a stacking sub module slot power supply and BUPS connector Figure 3 3 shows the back panel of the AC switch top and the DC switch bottom with a stacking sub module installed Figure 3 3 Avaya P330 AC and DC Back Panels Connector AC Input Cable to Cable to Lower Unit__ Upper Unit Power Supply Connector BUPS Connector DC Input Ed Cablelo Cable to Lower Unit___ Upper Unit 8 Power Supply Connector Note Further illustrations of the Avaya P330 Back Panel will be that of the AC model the topmost panel in Figure 3 3 Figure 3 3 shows
44. 48 Gigabit Ethernet Expansion Modules ooooc 148 Laser Safety iih tee dia aon iret tea 148 Laser ClassifiCatiOfi e ree ias 149 Usage Restriction eiii a A eene 149 L ser Dita etr eee e ere RE E e NN 149 Fast Ethernet Fiber Expansion Module ooooooooooo 150 Ethernet Fast Ethernet Expansion Module ooo 150 GBIC Expansion Module EE 151 Safety Information e eret terrent 151 Usage Restriction ns hei egest 151 Avaya P332MF User s Guide vii Table of Contents Avaya Approved GBIC Transceivers 152 SPECILI CAHIONS 2th AR RAN hana ee beet 152 Agency Approval sars eneng e ana 153 TED Pa Ne ani an ed RU Bra all i ie eve EE 153 X330GT2 Gigabit Ethernet Expansion Module 153 Installing the Expansion Module in the Avaya P330 153 Removing an Existing Expansion Module oo 154 Cable LN AN aa 154 ATM Expansion Modules ENEE 155 Safety Informaticas ee De e estia 155 Backup Power Supply BUPS see eee 156 Physical io casi 156 Power Requirements EE 156 ENVIO Mad 5 n eerie tates ERE e RE EE 157 SUN AAA A EN erede 157 EMC Emissions ierit etr ao ertet qeria E E dee eee eee det 157 EMISSIONS edu ttes tee oen Hemd Edel Ea 157 IMMUNITY i ote LINE AU teh tens 157 BUPS IMTBE ere IA reete ee te re RAE ee 157 MTBF in Various Confieurattons eene 158 Index of CLI Commandes 159 How to Gontact US ucro tte ocak tvs eret e a ER PEERS NER e ts 163 In
45. 70 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show rmon history Use the show rmon history command to show the most recent RMON history log for a given History Index The history index is defined using the rmon history command on Page 126 or using an RMON management tool The syntax for this command is show rmon history History Index gt P330 N show rmon history 1026 history Entry 1026 is active owned by amir onitors ifEntry 1 1026 every 30 seconds Requested 4 of time intervals ie buckets is 20 Granted 4 of time intervals ie buckets is 20 Sample 1 began measuring at 2 53 9 Received 62545 octets 642 packets 391 broadcast and 145 multicast packets 0 undersize and 0 oversize packets 0 fragments and 0 jabbers 0 CRC alignment errors and 0 collisions of dropped packet events due to a lack of resources 0 Network utilization is estimated at 0 show rmon alarm Use the show rmon alarm command to show the parameters set for a specific alarm entry that was set using the rmon alarm command on Page 127 or using the P330 Device Manager The syntax for this command is show rmon alarm lt Alarm Index gt Output Example P330 N gt show rmon alarm 1026 alarm alarm 1026 is active owned by amir Monitors ifEntry 1 1026 every 60 seconds Taking delta samples last value was 1712 Rising threshold is 10000 assigned to event 4 1054 Falling threshold is 10 assigned t
46. 86 EET EN EE 86 clear E E A E reputo EN NN NN mel mam tte etos 86 cleatiport mitrOE it AA Te A A reet 86 clearse cute TE 87 Set Commands Summary Table sss 88 See TR 91 SEE timezon NA BASA NN EN NENEK NAN 92 set time protocol eerte id 92 set time Server iu et esit s NN EN 93 SAA e e i tm rut et t a ede 93 SEL IP TOUTE i a eee eee eere ne ai me n RR ie s 93 Set snmp community En 94 iv Avaya P332MF User s Guide Table of Contents le E EE 94 set Stimp trap uth E 95 Set SNMP TEES eege dE ee tu na 95 set snmp timeout oom 96 set system location 4 nete eerie eer har deer dee 96 set system name En 96 set system contact En 96 set device mode 1 eese ettet ethernet tenente ense en 97 Seb TD terface eon eto eie EUM I debe ruris PO ttt ana ett tnt qe co deg 97 set interface PPP nos sucer ee otis an s 98 set port level ii eee tA a ir a eed e etre 99 set port negotiation ococooconcnconcnnononnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn entrent 99 Set port enable e eee e e ee endete lins 100 set port disables 22 eta dn Su de MN Na aan 100 s t port speed iui oe edi eee en atre MENARA 101 set port duplex crecido eene oit ere tate tratte diia 101 set port name seet eene ian aded inis 102 Setporttrap iii ee Na Bana 102 Set port Vai JA A A AAN NN ha 102 set port vlan binding mode se csse 103 Set port static vl n e eee taie iere tiere akta 103 set port self loop discovery Admin Statu
47. Activate SNMP traps disable Deactivate SNMP traps all Optional Specify all trap types config Optional Specify the ConfigChange trap from the TRAP MIB fault Optional Specify the Fault trap from the TRAP MIB rcvr addr IP address or IP alias of the system to receive SNMP traps 94 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Output Example To enable SNMP ConfigChange traps to a specific manager P330 N set snmp trap 192 168 173 42 enable config SNMP config change traps enabled Output Example To enable all traps to a specific manager P330 N set snmp trap 192 168 173 42 enable all All SNMP traps enabled Output Example To disable SNMP config traps to a specific manager P330 N set snmp trap 192 168 173 42 disable config SNMP config traps disabled Output Example To add an entry in the SNMP trap receiver table with default P330 N set snmp trap 192 168 173 42 SNMP trap receiver added set snmp trap auth Use the set snmp trap auth commands to enable disable the sending of SNMP traps upon SNMP authentication failure The syntax for this command is set snmp trap enable disable auth Output Example P330 N set snmp trap enable auth Authentication trap enabled set snmp retries Use the set snmp retries command to set the number of retries initiated by the Device Manager application when it tries to send SNMP messages to the de
48. GMT show timezone Usethe show timezone command to display the current stack timezone The syntax for this command is show timezone Output Example P330 N show timezone Timezone set to GMT offset from UTC is 0 hours show time parameters Usethe show time parameters command to display the status and parameters The syntax for this command is show time parameters Output Example P330 N show time parameters Current time L 02 49 11 02 JAN 1999 isl Timezone set to isl offset from UTC is 2 hours Time Server 0 0 0 0 Time acquired from Time Server 0 0 0 0 Time protocol set to TIME protocol Avaya P332MF User s Guide 45 Chapter 6 CLI Layer 2 show ip route Usethe show ip route command to display IP routing table entries The syntax for this command is show ip route Output Example P330 N gt show ip route Destination Gateway 149 49 1 1 THQ 20222201 190 20 0 0 17220122202 172 20 0 0 172 20 22 96 show image version Usethe show image version command to display the software version of the image on both memory banks of a specified switch The syntax for this command is show image version lt mod_num gt If no switch number is specified the image version of the all switches will be displayed Output Example P330 N show image version 1 Mod Module Type Bank Version il 24x10 100Base T with optional expansion slot A 3 3 14 1 24x10 100Base T with optiona
49. I Layer 2 No Expansion Not Present P330STK 2542 Conn Up Ok Conn Down Ok BUPS BUPS Not Prsnt Fans None Type None Avaya P332MF User s Guide 59 Chapter 6 CLI Layer 2 Output Fields Field Description Mod Switch number Type Module Type Expansion sub module type S N Serial number of the switch C S Hardware Configuration Symbol of the module expansion sub module Statuses Status of the module expansion sub module show port flowcontrol Usethe show port flowcontrol command to display per port status information related to flow control The syntax for this command is show port flowcontrol Output Example lt mod_num gt lt port_num gt P330 N gt show port flowcontrol 3 2 Port Send Flowcontrol Receive Flowcontrol Admin Oper 3 2 off Admin Oper 60 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Output Fields Field Port Send Flowcontrol Admin Send Flowcontrol Oper Receive Flowcontrol Admin Receive Flowcontrol Oper Description Switch and port number Send flow control administration Possible settings ON indicates that the local port is allowed to send flow control frames to the far end OFF indicates that the local port is not allowed to send flow control frames to the far end Send flow control operation mode Possible modes ONindicates that the local port will send flow control frames to the far end e OFF indicates that the local
50. Module Name Numbers Interface Ports X330F2 2 100Base FX Ethernet Fast Ethernet Expansion Module Table A 4 Ethernet Fast Ethernet Expansion Module Name Number ot Interface Ports X330T16 16 10 100Base T 150 Avaya P332MF User s Guide Appendix A Specifications GBIC Expansion Module 4 9 The Avaya X330G2 Expansion Module is the GBIC 1 25 Gbit s Gigabit Ethernet Expansion Module for the Avaya P330 family of stackable switches Note In order to use this module the Avaya P330 switch must must have Embedded S W Version 2 2 or higher You can download this from http www avayanetwork com The X330G2 can be used either as a Gigabit Ethernet link or as a high Bandwidth backplane for connecting switches The introduction of the GBIC interface to the Avaya P330 family presents an added value over the existing Gigabit Ethernet expansion modules You can insert any of the Avaya authorized GBIC transceivers into the X330G2 Expansion Module socket This provides you with a highly modular and customisable Gigabit Ethernet interface The GBIC transceivers are hot swappable Safety Information The multimode and single mode GBIC transceivers are Class 1 Laser products They comply with EN 60825 1 and Food and Drug Administration FDA 21 CFR 1040 10 and 1040 11 The GBIC transceivers must be operated under recommended operating conditions Laser Classification CLASS 1 LASER PR
51. ODUCT Note Class 1 lasers are inherently safe under reasonably foreseeable conditions of operation Caution The use of optical instruments with this product will increase eye hazard Usage Restriction When a GBIC transceiver is inserted into the X330G2 Expansion Module but is not in use then the Tx and Rx ports should be protected with an optical connector or a dust plug Avaya P332MF User s Guide 151 Appendix A Specifications v Avaya Approved GBIC Transceivers Caution All Avaya approved GBICs are 5V Do not insert a 3 3V GBIC Avaya supplies the following two GBIC transceivers for the Avaya P330 X330G2 Expansion Modules You can order these directly from your local Avaya representative using the PEC or COM Codes Type Description PEC Code COM Code GBIC SX Multimode Fiber 4705 122 108659228 Transceiver 1000BaseSx 550 m GBIC LX Single mode Fiber 4705 121 108659210 Transceiver 1000BaseLx 10 km In addition Avaya has tested and approved a number of GBIC transceivers from other manufacturers for use with the Avaya X330C2 Expansion Module An up to date list can be found in Avaya s website at the following address http www avayanetwork com Click on the Supported Devices icon Specifications X330G2 LX GBIC Transceiver A 9 mm or 10 mm single mode fiber SMF cable may be connected to a 1000Base LX GBIC port The maximum length is 10 km 32 808
52. P address or directly to one of the Router IP address 1 Connect your station to the network 2 Verify that you can communicate with the Avaya P330 using Ping to the IP of the Avaya P330 If there is no response using Ping check the IP address and default gateway of both the Avaya P330 and the station Note The Avaya P330 default IP address is 149 49 32 134 and the default subnet mask is 255 255 255 0 3 From the Microsoft Windows taskbar of your PC click Start and then Run or from the DOS prompt of your PC then start the Telnet session by typing telnet P330 IP address For example telnet 149 49 32 134 4 Ifthe IP Address in Telnet command is the IP address of the stack then connection is established with the Switch CLI entity of the Master module If you want to connect to the Router CLI entity use the session command If the IP address in the Telnet command is of the router connection is established to the Router CLI entity in the router module 5 When you see the Welcome to P330 menu and are prompted for a Login Name enter the default name root 6 When you are prompted for a password enter the User Level password root or norm inlower case letters do NOT use uppercase letters The User level prompt will appear when you have established communications with the Avaya P330 32 Avaya P332MF User s Guide Chapter 5 Avaya CLI Architecture Access amp Conventions Command Line Prompt When you start the CLI
53. PP incoming timeout is 10 minutes show ppp baud rate Use theshow ppp baud rate command to display the set baud rate The syntax for this command is show ppp baud rate Output Example P330 N show ppp baud rate PPP baud rate is 38400 show ppp configuration Use the show ppp configuration command to display the ppp configuration The syntax for this command is show ppp configuration Output Example P330 N show ppp configuration PPP baud rate is 38400 PPP incoming timeout is 0 minutes PPP Authentication Parameters Incoming None Avaya P332MF User s Guide 73 Chapter 6 CLI Layer 2 show tftp download upload status Use the show tftp download status and show tftp upload status commands to display the status of the current TFTP configuration file copy process into from the device The syntax for this command is show tftp download upload status Output Example lt mod_num gt P330 N gt show tftp upload status 1 Module Source file Destination file Host Running state Failure display Last warning show tftp download software status 1 stack config c conf cfg 149 49 36 200 Executing null No warning Use the show tftp download software status commands to display the status of the current TFTP Device Manager S W Embedded Web download process into the device The syntax for this command is show tftp download software status Output Example lt mod_num
54. R Deeg Biriez e hr User A A om n ordi mr re Avaya P332MF User s Guide 141 Chapter7 Installing the Embedded Web Manager Ifyou have the Java plug in installed the Web based manager should open in a new window see Figure 7 2 Figure 7 2 Web based Manager Ifyou do not have the Java plug in installed follow the instructions on the Welcome page that offers a variety of options to install the plug in see Figure 7 1 142 Avaya P332MF User s Guide Chapter 7 Installing the Embedded Web Manager Installing the Java Plug in If the network manager has configured the system the plug in should be installed automatically Note Ensure that Java or JavaScriptis enabled on your Web browser Please refer to your browser on line help or documentation for further information If the plug in is not installed automatically then you have three options for installing it manually 1 Installing from the Avaya P330 Documentation and Utilities CD 1 Close all unnecessary applications on your PC Insert the Avaya P330 Documentation and Utilities CD into the CD drive Click Start on the task bar Select Run Type x emweb aux files plug in_1_3_1 exe where x is the CD drive letter Follow the instructions on screen Jg A ON oN 2 Install from the Avaya Site Click on the link in the Welcome page 3 Install from your Local Web Site Click on the link in the Welcome page Note This option is on
55. Sets the switch parameters Page 88 a group of commands synctime Synchronizes the time between switches Page 118 e get time Gets the time from the time server Page 123 reset Restarts the system or a switch Page 124 e reset stack Causes a hardware reset to the stack Page 124 reset mgp Causes a software reset to the Media Page 124 Gateway Processor nvram initialize Initializes the NVRAM to its factory Page 125 defaults rmon history Creates a history entry Page 126 rmon alarm Creates an alarm entry Page 127 rmon event Creates an event entry Page 128 copy stack config Uploads stack configuration to a file Page 128 tftp using TFTP The file must exist before you Upload copy module Uploads switch configuration to a file Page 129 config tftp using TFTP The file must exist before you Upload copy tftp stack Downloads a stack configuration file Page 130 config using TFTP into the device Avaya P332MF User s Guide 81 Chapter6 CLI Layer 2 copy tftp module Downloads a switch configuration file Page 130 config using TFTP copy tftp Downloads the Device Manager S W Page 131 EW Archive Embedded Web Archive file using TFTP into the device copy tftp Updates the software image and device Page 131 SW image manager application of a designated switch radius Sets radius authentication parameters Page 132 authentication 1 The clear command corresponds to a group of commands and is shown
56. TP upload Page 74 download status download configuration per switch show tftp download Shows the status of the TFTP software Page 74 software status download of the Device Manager software to the switch show web Shows the location URL directory of Page 75 aux files url the P330 Device Manager Help files show intelligent Shows the status IP multicast filtering Page 75 multicast application show intelligent Shows whether the connected unit s Page 76 multicast hardware hardware supports IP multicast filtering support show security mode Displays the status of the MAC security Page 76 feature enabled disabled e show secure mac port Shows the secure MAC addresses of a Page 77 port e show arp tx interval Displays the keep alive status Page 77 show arp aging Displays the ARP table aging interval for Page 77 interval gateways entries show self loop Displays the self loop discovery mode Page 78 discovery show allowed Displays the status of the allowed Page 78 managers status managers feature enabled disabled show allowed Displays the IP addresses of the allowed Page 79 managers table managers 44 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 dir Displays the file types that have been Page 79 downloaded to the module show time Usethe show time command to display the current stack time The syntax for this command is show time Output Example P330 N show time 10 32 34 27 JAN 2000
57. User s Guide AVAYA P332MF STACKABLE SWITCH SOFTWARE VERSION 3 12 May 2002 AVAYA Preface FCC Notice This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense Changes or modifications to this equipment not expressly approved by Avaya Inc could void the user s authority to operate the equipment Conventions Used in the Documentation CLI Documentation for this product users the following conventions to convey instructions and information e Mandatory keywords you type in are in the computer bold font e Information displayed on screen is displayed in computer font e Variables that you supply are in pointed brackets lt gt e Optional keywords are in square brackets e Alternative but mandatory keywords are grouped in braces and separated by a vertical bar e Lists of parameters from which you should choose are enc
58. Y Windows 95 which are not present if Internet Explorer is not installed In order to add these services to the operating system please install Internet Explorer version 3 or higher You can then use either browser to manage the switch Running the Embedded Web Manager o Note You should assign an IP address to the switch before beginning this procedure 1 Open your browser 2 Enter the url of the switch in the format http aaa bbb ccc ddd where aaa bbb ccc ddd is the IP address of the switch Note The user name is root The default password for read write access is root Note The Web management passwords are the same as those of the CLI If you have created additional CLI user names or changed the default passwords then you can use those passwords for Web management as well 140 Avaya P332MF User s Guide Chapter7 Installing the Embedded Web Manager The welcome page is displayed Figure 7 1 The Welcome Page Webcome to the Coup P330 Device Manager Te appleumen re parry ior Som bcne Lem Pag in rerema L Des br ied y prar oram Ee ur xcd dirrach morie im re dr prc rbv el da ume d En poa brape shh wi chor rre e ror conira i7 ell iur rem Han dos wor eco atum a Een un Odit POS RAF gn epes pln kd zsm Ms diodos ian Mer ia alib Joli Lar draw abd E tl Eur ee e Kx 8 ben jer dike domm aiu coi acm br eer lr pmi amm rra b o oapiri orc rha wm mci labis a krit dran ie mcer CE pnmo d dl Hn FI
59. a Modem to the Console Port eee 29 Assigning P330 s IP Stack Address 30 Avaya CLI Architecture Access amp ConventiOnS ooo o 31 Establishing a Serial Connection 31 Establishing a Telnet Connection seen 32 Command Line Prompt sese eene eene 33 Avaya P330 EE 33 Security Levels a A A eee AA 34 Entering the Supervisor Level esses 34 Defining new users ENEE 34 Exiting the Supervisor Level ooooooooooocc 34 Entering the CET netten AE 35 Entering the Technician Level EEN 35 Conventions Used iia MERASA Pul 35 Navigation Cursor Movement and Shortcuts oooooo 36 Getting Flelpi sc ina dt tree RR TR elei ies 36 Command Syria ue icem rette Fre aan rese reveren 36 Command Abbreviations eese nennen enne nnne 36 Universal Commands isi eege Ee ee 37 Top and Up commands een 37 Retstatus commande 37 Tree COMMA retener de Lt D eer te e DS 37 CLE Sayre nita AAS ee AN NAN NN BEE 39 User Level Commandes 39 SOSSLOM EE 40 terminal a dte tentem muse NN e siete od 40 Clear SEE GE 41 PIE Deia A NN NN NN 41 Show Commands Summary Table E 42 ii Avaya P332MF User s Guide Table of Contents STOW EE 45 show TIMEZONE EE 45 show time parameters oooooooooooooo 45 Show Ip Toute ceci la en etie asah 46 show image version ENEE 46 show download status sess eene nente 47 A eee peni eee Hh eerie ree eee 47 show SNMP
60. able Enables disables the SNMP authentication trap Sets the number of SNMP retries Sets the SNMP timeout Sets the system location Sets the system name Sets the system contact person Sets the basic mode of operation Configures the management interface of the device Configures the device ppp interface Sets the priority level of a port Sets the auto negotiation mode of a port Administratively enables a port Page 91 Page 92 Page 92 Page 93 Page 93 Page 93 Page 94 Page 94 Page 95 Page 95 Page 96 Page 96 Page 96 Page 96 Page 97 Page 97 Page 98 Page 99 Page 99 Page 100 88 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set port disable Administratively disables a port Page 100 set port speed Sets the speed for a 10 100 port Page 101 e set port duplex Sets the duplex mode of a port Page 101 setport name Assigns a name to a port Page 102 set port trap Enables disables the SNMP up down Page 102 link traps sent for port e set port vlan Assigns the Port VLAN ID PVID Page 102 e setportvlan binding Defines the port binding method Page 103 mode set port static vlan Defines a multiple VLANs per port Page 103 set port self loop Defines a port s IBM token ring Page 104 discovery discovery mode Admin Status set port channel Defines a LAG interface Page 104 set port classification Defines port classification Page 105 setport redundancy Defines de
61. able MAC security at the stack level When enabled the ports are secured based on their individual configuration When disabled all the ports in a stack are non secured The syntax for this command is set security mode enable disable Output Example P330 N set security mode enable Security mode enabled set arp aging interval Use this command to set the ARP table aging interval for gateways entries in the agent ARP table The MAC value for the default gateway of ML agent in the ARP table is deleted at the end of every aging interval The default value is 10 minutes The syntax for this command is set arp aging interval value value The number representing the interval from 0 10 minutes Example P330 N set arp aging interval 20 ARP aging interval was set to 20 minutes set arp tx interval Use the set arp tx interval command to set the keep alive frames sending interval Setting the interval to 0 disables the transmission of the keep alive frames The syntax for this command is set arp tx interval value value The interval in seconds 120 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Output Example P330 N set arp tx interval 15 ARP tx interval was set to 15 seconds set self loop discovery Admin Status Usetheset self loop discovery Admin Status command to enable or disable IBM token ring discovery feature at the module level Note You must dis
62. able Spanning Tree before you can enable self loop discovery Note This command is not supported by the P332G ML and P332GT ML switches The syntax for this command is set self loop discovery Admin Status lt enable disable gt modul num Example P330 N set self loop discovery Admin Status enable 1 Self Loop Discovery is disabled on module 1 set welcome message Usethe set welcome message command to set a welcome message to appear after a reboot or after opening a new session see session command in the stack The syntax for this command is set welcome message string string string The string to be used as the welcome message blank Restores the default string Output Example P330 N set welcome message avaya The new welcome string is avaya Avaya P332MF User s Guide 121 Chapter 6 CLI Layer 2 Note If you wish to define a string which includes spaces you must enclose the entire string in quotation marks e g new york set allowed managers Use the set allowed managers command toenable disable the Allowed Managers feature When this feature is enabled only those stations whose IP addresses are listed in the Allowed Managers table can access the device over Telnet SNMP or HTTP The syntax for this command is set allowed managers enabled disabled Output Example P330 N set allowed managers enabled Managers ar nabled set allowed
63. aces of the device Shows the operating mode you are currently in Shows settings and status for all ports Shows the port trap Shows the port channel Displays the port classification Displays information on redundancy schemes Shows the stack s intermodule redundancy Shows mirroring information Shows port vlan binding mode settings Lists the security mode of the ports of a switch or stack Displays the port blocking mode on a particular switch Page 45 Page 45 Page 45 Page 46 Page 46 Page 47 Page 47 Page 48 Page 48 Page 48 Page 48 Page 49 Page 49 Page 50 Page 51 Page 51 Page 52 Page 52 Page 53 Page 53 Page 53 Page 54 Page 54 42 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 e show portself loop Displays which port or switch has an Page 57 discovery enabled IBM token ring cable loop discovery status show internal Shows the current internal buffering Page 57 buffering capacity show boot bank Displays the software bank from which Page 58 the switch will load show module Shows switch status and information Page 58 show port Shows the per port status information Page 60 flowcontrol related to flow control e show cam Shows the CAM table entries for a Page 62 specific port e show cascading fault Shows cascading fault monitoring mode Page 62 monitoring show port auto Displays the flowcontrol advertisement Page 63 negotiation for a Gigabit port
64. al The interval between 2 samples number of The number of buckets defined buckets owner name The owner name string Output Example P330 N rmon history 1026 1026 3 2 30 buckets 20 owner amir history 1026 was created successfully 126 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 rmon alarm Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Usethe rmon alarm command to create a new RMON alarm entry The syntax for this command is rmon alarm Alarm Number variable interval lt sampletype gt rising threshold rising threshold rising event falling threshold falling threshold falling event startup alarm owner alarm number variable interval sample type rising threshold rising event falling threshold falling event startup alarm owner Output Example This is the alarm index number of this entry itis advisable to use the same interface number as your alarm index number This is the MIB variable which will be sampled by the alarm entry The interval between 2 samples This can be set to either delta the difference between 2 samples or an absolute value This sets the upper threshold for the alarm entry The RMON event entry that will be notified if the upper threshold is passed This sets the lower threshold for the alarm entry The RMON event entry tha
65. allowed on trunk 1 5 off statically bound 1 1 Output Fields Field Description Port Switch and port number s Mode Tag status of the port dot1q dot1O tagging mode show vlan off clear mode Binding mode Binding mode of the port Native VLAN Number of the Port VLAN ID the VLAN to which received untagged traffic will be assigned VLANsallowed Range of VLAN values allowed on the port on trunk Use the show vlan command to display the VLANs configured in the stack switch The syntax for this command is show vlan Output Example P330 N show vlan VLAN ID Vlan name 1 v1 5 v5 10 V10 15 V15 20 V20 25 V25 64 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show leaky vlan Use the show leaky vlan command to display the leaky VLAN status The syntax for this command is show leaky vlan Output Example P330 N gt show leaky vlan Leaky VLAN mode Disable show spantree Usethe show spantree command to display spanning tree information The syntax for this command is show spantree mod num port num Output Example P330 N show spantree Spanning tree enabled Designated Root 00 40 0d 88 06 c8 Designated Root Priority 32768 Designated Root Cost 20 Designated Root Port 1 1 Root Max Age 20 Hello Time 2 Bridge ID MAC ADDR 00 40 0d 92 04 b4 Bridge ID priority 32768 Port State Cost Priority 1 Forwarding 20 128 2 not connected 20 128
66. ame and the default password root inlowercase letters Welcome to P330 Login root Password Password accepted P330 N super Defining new users Define new users and access levels using the username command in Supervisor Level see page 135 Exiting the Supervisor Level To exit the Supervisor level type the command exit 34 Avaya P332MF User s Guide Chapter 5 Avaya CLI Architecture Access amp Conventions Entering the CLI To enter the CLI enter your username and password Your access level is indicated in the prompt as follows The User level prompt is shown below P330 N The Privileged level prompt is shown below P330 N The Configure level prompt for Layer 3 configuration is shown below P330 N configure The Supervisor level prompt is shown below P330 N super Entering the Technician Level This level is can only be accessed from the Privileged and Supervisor levels not from the User level This feature is not documented and is for use by Avaya Technical Support only Conventions Used The following conventions are used in this chapter to convey instructions and information e Mandatory keywords are in boldface e Variables that you supply are in pointed brackets lt gt e Optional keywords are in square brackets e Alternative but mandatory keywords are grouped in braces and separated by a vertical bar e If you enter an alphanumeric string of two w
67. ar 31 70 414 8059 Yemen 31 70 414 8062 Romania 31 70 414 8027 Yugoslavia 31 70 414 8038 Russia 7 095 733 9055 Zimbabwe 31 70 414 8063 Saudi Arabia 31 70 414 8022 Email csctechnical avaya com 164 Avaya P332MF User s Guide How to Contact Us In the AP Asia Pacific Region Country Local Dial In outs Local Dial In Number Australia 1800 255 233 Hong Kong 2506 5451 Indonesia 800 1 255 227 Japan 0 120 766 227 Korea 0 80 766 2580 Email sgcoe avaya com In the CALA Caribbean and Latin America Region Email caladatasupp avaya com Hot Line 1 720 4449 998 Fax 1 720 444 9103 Number Malaysia 1800 880 227 New 00 800 9828 9828 Zealand Philippines 1800 1888 7798 Singapore 1800 872 8717 Taiwan 0 80 025 227 For updated information visit www avayanetwork com and click Global Support Organization GSO Avaya P332MF User s Guide 165 How to Contact Us All trademarks registered trademarks service names product and or brand names are the sole property of their respective owners Copyright O 2002 Avaya Inc All rights reserved 166 Avaya P332MF User s Guide
68. are prompted for a password enter the password root You are now in Supervisor Level 4 Atthe prompt type set interface ppp lt ip_addr gt lt net mask gt with an IP address and netmask to be used by the Avaya P330 to connect via its PPP interface Note The PPP interface configured with the set interface ppp command must be on a different subnet from the stack inband interface Avaya P332MF User s Guide 29 Chapter 4 Installation and Setup 5 Set the baud rate ppp authentication and ppp time out required to match your modem These commands are described in the Command Line Interface chapter 6 At the prompt type set interface ppp enable The CLI responds with the following Entering the Modem mode within 60 seconds Please check that the proprietary modem cable is plugged into the console port 7 Use the DB 25 to RJ 45 connector to plug the console cable to the modem s DB 25 connector Plug the other end of the cable RJ 45 connector to the Avaya P330 console s RJ 45 port 8 The Avaya P330 enters modem mode 9 You can now dial into the switch from a remote station and open a Telnet session to the PPP interface IP address Assigning P330 s IP Stack Address Note All P330 switches are shipped with the same default IP address You must change the IP address of the master P330 switch in a stack in order to guarantee that the stack has its own unique IP address in the network Use
69. authentication is set show radius authentication Usethe show radius authentication command to display all RADIUS authentication configurations The shared secrets are not displayed The syntax for this command is show radius authentication 136 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Example P330 N super show radius authentication RADIUS authentication parameters Mode Enabled Primary server 192 168 42 252 Secondary server 192 168 48 134 Retry number 4 Retry time 5 UDP port 1645 Shared secret sodot set radius authentication Usethe set radius authentication command to enable or disable authentication for the P330 unit RADIUS authentication is disabled by default The syntax for this command is set radius authentication enable disable tech Use the tech command to enter tech mode This command is reserved for service personnel use only Avaya P332MF User s Guide 137 Chapter 6 CLI Layer 2 138 Avaya P332MF User s Guide Chapter 7 Installing the Embedded Web M anager The Embedded Web Manager provides the following Managing and monitoring Power over Ethernet Device Configuration Viewing and modifying the different device configurations Virtual LANs Viewing and editing Virtual LAN information Link Aggregation Groups LAGs Viewing and editing LAG information Software Redundancy Setting software redundancy for ports in an Avaya P330 Switch
70. bs 2 Take hold of the two knobs one near each side of the front panel and pull gently but firmly towards yourself 3 Insert another expansion sub module or the blanking plate Note If an expansion sub module is removed from the stack with the power supply e on all configuration definitions on expansion sub modules are lost To remove an expansion sub module and save configuration definitions 1 Turn off the power supply 2 Remove an expansion sub module 3 Insert another expansion sub module 4 Tumon the power supply Note The Avaya P330 switch must not be operated with the expansion slot open the expansion sub module slot should be covered with the supplied blanking plate if necessary 24 Avaya P332MF User s Guide Chapter 4 Installation and Setup Powering On Avaya P330 Module AC For the AC input version of the Avaya P330 insert the AC power cord into the power inlet in the back of the unit The unit powers up even if no direct AC power is applied to it 1 If you are using a BUPS insert a power cord from the BUPS into the BUPS connector in the back of the unit The unit powers up 2 After power up or reset the Avaya P330 performs a self test procedure Powering On Avaya P330 Module DC For the DC input version of the Avaya P330 connect the power cable to the switch at the input terminal block 1 The terminals are marked and with the IEC 5019a Ground symbol 2 The size of the
71. ce mode command to change the Basic Mode of Operation of the P332 ML P332GT ML P333R P333R LB switches between Router and Layer 2 modes Note This command is not supported by the P333T P334T P332MF switches which do not have Router mode The syntax for this command is set device mode mode mode Router Layer2 set interface Usethe set interface command to configure the management interface on the Master agent of the stack The syntax for this command is set interface inband lt vlan gt lt ip_addr gt lt netmask gt inband Interface name used for the management vlan The number of the VLAN to be used for management ip_addr IP address used for managing the stack netmask Subnet mask of the management interface Output Example P330 N set interface inband 1 192 168 42 252 255 255 255 0 Interface inband IP address set You must reset the device in order for the change to take effect Avaya P332MF User s Guide 97 Chapter 6 CLI Layer 2 setinterface ppp Use the set interface ppp command to configure the P330 PPP interface IP parameters exit modem mode disconnect the PPP session or reset the connected modem A PPP connection can be established only after the P330 is configured with an IP address and net mask The IP address is a dummy address that is shared between two peers and must be taken from a subnet that is different from the agent s IP sub net The syntax for this command
72. d to remove a MAC address from the CAM table of a secured port o Note This command is not supported by the P330 ML switches The syntax for this command is clear secure mac lt mac address gt port mod num port num Output Example P330 N clear secure mac 1 2 3 4 5 port 1 17 01 02 03 04 05 cleared from secure address list for port 1 17 Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch Avaya P332MF User s Guide 87 Chapter 6 CLI Layer 2 Set Commands Summary Table Following is a Table of the Privileged Level set commands set logout set timezone set time protocol set time server set time client set ip route set snmp community set snmp trap set snmp trap auth set snmp retries set snmp timeout set system location set system name set system contact set device mode set interface set interface ppp set port level set port negotiation set port enable Sets the number of minutes before an inactive CLI session automatically logs out Sets the timezone for the system Sets the time protocol for use in the system Sets the NTP server address Enables or disables the time client Adds IP addresses to the IP routing table Sets the SNMP community string for a specific switch Sets the SNMP trap of the system or add delete an entry into from the SNMP trap receiver t
73. e User and Privileged Levels including all show and set commands Use the username command to add a local user account You can only do this from within the Supervisor Level The syntax for this command is username lt name gt password lt passwd gt access type read only read writeladmin name New user name passwd User s password access type Access type definition read only read write or administrator Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Use the no username command to remove a local user account The syntax for this command is no username lt name gt Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Avaya P332MF User s Guide 135 Chapter 6 CLI Layer 2 show username Use the show username command to display the username The syntax for this command is show username Output Example P330 N gt show username User account password access type root AAA admin set ppp chap secret Usethe set ppp chap secret command to configure the shared secret used in PPP sessions with CHAP authentication The syntax for this command is set ppp chap secret lt chap secret gt chap secret The shared secret 4 to 32 characters Output Example P330 N super set ppp chap secret sodot PPP shared secret for CHAP
74. e blanking plate from the back of the Avaya P330 switch Insert the stacking sub module gently into the slot ensuring that the metal base plate is aligned with the guide rails The metal plate of the X330STK and not the PCB fits onto the guide rails Press the sub module in firmly until it is completely inserted into the Avaya P330 Gently tighten the two screws on the side panel of the stacking sub module by turning them Note The Avaya P330 switch must not be operated with the back slot open the stacking sub module should be covered with the supplied blanking plate if necessary Positioning Avaya P330 can be mounted alone or in a stack in a standard 19 inch equipment rack in a wiring closet or equipment room Up to 10 units can be stacked in this way When deciding where to position the unit ensure that It is accessible and cables can be connected easily and according to the configuration rule Cabling is away from sources of electrical noise such as radio transmitters broadcast amplifiers power lines and fluorescent lighting fixtures Water or moisture cannot enter the case of the unit There is a free flow of air around the unit and that the vents in the back and sides of the case are not blocked Avaya P332MF User s Guide 19 Chapter4 Installation and Setup BD Note Use Octaplane cables to interconnect with other switches Rack Mounting The Avaya P330 case fits in most standard 19 inch racks Avaya
75. e tese esae ee peo do 70 show mon history descente eere ite eee AA 71 Show rmorvalattm erret rro to roe trn sonas Lage Se EE 7 Avaya P332MF User s Guide iii Table of Contents le une eine t NN BNN ee dee Pedes 72 show ppp session E 72 show ppp authentication sese eee nenne 72 Show ppp incoming timeout eee eee nen 73 show ppp ba d rate siss e nue ee eei esi e 73 show ppp configuration seeeeseeeeeeeeeeee nennen 73 show tftp download upload status ooooooooooco ooooo 74 show tftp download software status oooooooooo 74 show web aux files url sss netten 75 show intelligent multicast EE 75 show intelligent multicast hardware support o 76 show security mode erede pe erred tenentes 76 show secure MAC Port madina inn ema SEENEN 77 show arp tx interval ENEE 77 show arp aging interval oooocooooo 77 show self loop discovery sss 78 show allowed managers status o ooooooo 78 show allowed managers table ooooooooooo Woooc 79 nde m EE 79 Privileged Level Commands EEN 81 no h stridme s iae etii net temet ei ER 82 tio mor listory ase de nee Bala 82 MOM Or RER EE 82 NS ACRI ERR 83 lafe TEE 83 Clear Commands Summary Table een 83 clear mezotie rae EN UNNES 84 E Ee 84 Clear simp trap xn atte ed ed eet ee bts 84 ACA IO da ES 85 Clear dynamic vlans mes minta en tmn laman Banana 85 Clear portistatic laicidad
76. ee BNN o codon ee d Pe NN NN 135 show DEE EE 136 set ppp chap Secret iii AE aid edens 136 show radius authentication oooooWooo oo 136 set radius authentication sss nennen nennen 137 tech Ges e EU REINES RU SE 137 Chapter 7 Installing the Embedded Web Manager 139 System Requirements EE 139 Running the Embedded Web Manager oooo oo o oooo 140 Installing the Java Plug in tene 143 Installing the On Line Help and Java Plug In on your Web Site 144 Documentation and Online Help EE 144 Software Download 3 5 cites eka 144 Appendix A Specificatioris es epe rtt te re ee Pete cios 145 Avaya P332MF Switch cei ie e e ise to ee Ae 145 Physical Eta utendo et t oet 145 Power Requirements AC EE 145 Power Requirements DC eee eee 145 Laser Data iua dte einem i te isse IR 145 Ernvitonmoental 2 35 unite nite c E E 146 Safety c M 146 Avaya P330 DC Input Version En 146 Agency Approvals tiet bue tinte aie Bt det ite ete be pe reete 146 EMCZEmissiOofns ueste ee adds 146 Immunity tee rero hes ive CREER e reir ve e Si 147 OREN donis cote et Drei a resto eae esee tite Torten 147 Interfaces niis te mt tti eie e fi 147 Standards Compliance 147 TEE E eT nete Rte eese Pe iat bes 147 IER RE 147 Basie MTBE 532 estet est ted tenet scere e Pe UN 147 stacking Module conoci iere eee ete 148 Expansion Modules 43 etre reete Pre EE 1
77. eful for access using the Device Manager The syntax for this command is show snmp timeout Output Example P330 N show snmp timeout the SNMP Timeout is 2000 Usethe show timeout command to display the amount of time the CLI can remain idle before timing out in minutes If the result is 0 there is no timeout limit The default is 15 minutes The syntax for this command is show timeout Output Example P330 N show timeout CLI timeout is 10 minutes Usethe show logout command to display the amount of time the CLI can remain idle before timing out in minutes If the result is 0 there is no timeout limit The default is 15 minutes 48 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 The syntax for this command is show logout Output Example P330 N show logout CLI timeout is 10 minutes show interface Usethe show interface command to display information on network interfaces The syntax for this command is show interface Output Example To display the interface P330 N show interface Interface Name VLAN IP address Netmask inband 1 10 0 0 1 255 255 255 0 ppp disable 1 0 0 0 0 0 0 0 0 show device mode Use the show device mode command to show the P332G ML P332GT ML P333R P333R LB operating mode you are currently in Possible modes are Router or Switch Note This command is not supported by the P333T P334T P332MF P333T PWR switches which do not have Router mode
78. enable Usethe set port enable command to enable a port or a range of ports The syntax for this command is set port enable mod num port num mod num The switch number port num The port number Output Example To enable port 3 on module 2 P330 N set port enable 2 3 Port 2 3 enabled set port disable Usethe set port disable command to disable a port The syntax for this command is set port disable mod num port num Output Example P330 N set port disable 5 10 Port 5 10 disabled 100 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set port speed Usethe set port speed command to configure the speed of a 10 100Base T port If autonegotiation mode is enabled for such ports the port s speed is determined by autonegotiation and an error message is thus generated if you attempt to perform the set port speed command in this case Note This command does not apply to P332G ML and P332GT ML ports An error message is generated if you attempt to perform the set port speed command for P332G ML and P332GT ML ports The syntax for this command is set port speed mod num port num value Output Example To configure port 2 on module 2 port speed to 10 Mbps P330 N set port speed 2 2 10MB Port 2 2 speed set to 10 Mbps set port duplex Usethe set port duplex command to configure the duplex mode of a 10 100Base T port You can configure the duplex mode to either Half or Full duplex
79. er dissipation 150 W max Input current 53A Power Requirements DC Input voltage 36 to 72 VDC Power dissipation 150 W max Input current 5 1 A max Inrush current 50 A max Laser Data Laser type Multimode Wavelength 1300 nm Avaya P332MF User s Guide 145 Appendix A Specifications Output power 0 60 W max dissipation Transmit power 19 dbm min 14 dbm max Receive power 31 dbm max Environmental Operating Temp 5 to 50 C 23 to 122 F Safety Relative Humidity 5 to 95 non condensing UL for US approved according to UL1950 Std C UL UL for Canada approved according to C22 2 No 950 Std CE for Europe approved according to EN 60950 Std Laser components are Class 1 Laser Products EN 60825 IEC 825 1 for Europe FDA 21 CFR 1040 10 and 1040 11 for USA Overcurrent Protection A readily accessible listed safety approved protective device with a 16A rating must be incorporated in series with building installation AC power wiring for the equipment under protection Avaya P330 DC Input Version Restricted Area Access This device should only be installed in a restricted access area Installation Codes This device must be installed in accordance with the US National Electrical Code Articles 110 26 and 110 27 and the Canadian Electrical Code Section 12 Overcurrent Protection A readily accessible Listed branch circuit overcurrent protective device with a 15A rating must be incorporated in the building
80. ers are disabled 78 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show allowed managers table Use the show allowed managers table command show the list of the twenty possible allowed managers IP addresses show allowed managers table show allowed managers status Output Example P330 N gt 1 149 49 32 134 2 Not Used 3 Not Used 4 Not Used 5 Not Used 6 Not Used 7 Not Used 8 Not Used 9 Not Used 10 Not Used 11 Not Used 12 Not Used 13 Not Used 14 Not Used 15 Not Used 16 Not Used 17 Not Used 18 Not Used 19 Not Used 20 Not Used dir Use the dir command to show the file types that have been downloaded to the switch The syntax for this command is dir lt mod_num gt Avaya P332MF User s Guide 79 Chapter6 CLI Layer 2 Output Example P330 N dir Mt file ver num file type file location file description 1 Booter Image E Ee SW Boot Image Nv Ram Booter Image 1 module config N A Running Conf Ram Module Configuration 1 stack config N A Running Conf Ram Stack Configuration 1 EW Archive N A SW Web Image Nv Ram Web Download 2 Booter Image 3 2 5 SW Boot Image Nv Ram Booter Image 2 module config N A Running Conf Ram Module Configuration 2 EW Archive N A SW Web Image Nv Ram Web Download Output Fields Field Description MH The switch number file There are several files loaded into the switch s memory e module config file which contains the conf
81. eset Example To reset a WAN module residing on switch 2 P330 N4 reset wan 2 This command will force a switch over to the wan device and disconnect your telnet session xxx Reset do you want to continue Y N y nvram initialize Usethe nvram initialize command to reset the P330 parameters to the factory defaults If no options are specified for this command only the Layer 2 parameters will be reset Avaya P332MF User s Guide 125 Chapter 6 CLI Layer 2 rmon history The syntax for this command is nvram initialize switch all switch Resets all the switching level parameters Layer 2 only throughout the stack all Resets all parameters including licenses and routing parameters of the Layer 3 switches present in the stack Output Example P330 N nvram initialize This command will force a factory default and switch over to the master module and disconnect your telnet session Do you want to continue y n n y Connection closed by foreign host host Use the rmon history command to create an RMON history entry The syntax for this command is rmon history lt history index gt lt module gt lt port gt interval lt interval gt buckets lt number of buckets gt owner lt owner name gt history_index This is the history index number of this entry it is advisable to use the same interface number as your history index number module port The switch number the port number interv
82. et port vlan command to set the Port s VLAN ID PVID The VLAN number must be within the range 1 to 3071 The syntax for this command is set port vlan value mod num port num value Number between 1 and 3071 identifying the VLAN mod num The switch number the port number port num 102 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Output Example To set VLAN 850 to include ports 4 through 7 on module 3 P330 N set port vlan 850 3 4 7 VLAN 850 modified VLAN Mod Ports 850 3 4 7 set port vlan binding mode Use the set port vlan binding mode command to define the binding method used by ports The syntax for this command is set port vlan binding mode port list value port list Switches and ports to bundle format switch port value static the port supports only the VLAN as configured per port bind to configured the port supports the VLANs configured on the device bind to all the port support the whole range of VLANs on the device Output Example P330 N set port vlan binding mode 1 5 9 static Set Port vlan binding method 1 5 Set Port vlan binding method 1 6 set port static vlan Use the set port static vlan command to statically assign VLANs to ports The syntax for this command is set port static vlan module port range vlan num module port port range vlan range vlan to bind to port Avaya P332MF User s Guide 103 Chap
83. for the management vlan from 1 to 3071 Avaya P332MF User s Guide 111 Chapter 6 CLI Layer 2 set vlan The syntax for this command is set inband vlan value value A VLAN number between 1 and 3071 Output Example P330 N set inband vlan 1 Management VLAN number set to 1 Use the set vlan command to create VLANS The syntax for this command is set vlan vlan id name vlan name vlan id vlan number vlan name vlan name Output Example P330 N set vlan 3 name v3 VLAN ID 3 is named v3 Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york set port flowcontrol Use the set port flowcontrol command to set the send receive mode for flow control frames IEEE 802 3x or proprietary for a full duplex port Each direction send or receive can be configured separately only for Gigabit Ethernet ports Proprietary flow control cannot be configured on Gigabit ports The set flowcontrol command cannot be used on Gigabit ports for which autonegotiation is enabled The syntax for this command is set flowcontrol direction module port value where the parameters of direction are receive send all and the parameters of value are on off proprietary 112 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Field Description receive Controls the receipt of IEEE802 3x flow control frames on Gigabit ports only
84. for the most up to date settings Table 4 1 Default Switch Settings Function Default Setting IP address 149 49 32 134 Default gateway 0 0 0 0 VLANs VLAN 1 Spanning tree Enabled Bridge priority for Spanning Tree 32768 Time server IP address 0 0 0 0 Timezone offset 0 hours Read only SNMP community string Public Read write SNMP community string Public Trap SNMP community string Public SNMP retries number 3 SNMP timeout 2000 Seconds SNMP authentication trap Disabled CLI timeout 15 Minutes User Name Password root root 26 Avaya P332MF User s Guide Chapter 4 Installation and Setup Table 4 2 Default Port Settings Function Default Setting 10 100Base TX ports 100Base F ports 1000 Base X ports Duplex mode Full duplex Full duplex Full duplex only Port Speed 100M 100M 1000M Flow control Off Off Off Flow control Off N A Off No pause advertisement Backpressure On only in Half duplex Not Applicable Not Applicable Autopartitioning Disabled only in Half N A N A duplex Auto negotiation Enable Not Applicable Enable Administration status Enable Enable Enable Port VLAN 1 1 1 Tagging mode Clear Clear Clear Port priority 0 0 0 Spanning Tree cost 20 20 4 Spanning Tree port 128 128 128 priority 1 Ensurethat the other side is also set to Autonegotiation Enabled
85. he top and bottom switches of a stack Catalog No CB0222 CB0269 These are the same cables that are used with all P330 family modules To connect stacked switches Note When adding a module to an existing stack first connect the stacking cables and then power up the module Plug the light grey connector of the Short Octaplane cable into the port marked to upper unit of the bottom Avaya P330 switch Plug dark grey connector of same Short Octaplane cable to the port marked to lower unit in the unit above The connections are illustrated in Figure 4 3 Repeat Steps 1 and 2 until you reach the top switch in the stack If you wish to implement stack redundancy use the Redundant Cable to connect the port marked to lower unit on the bottom switch to the port marked to upper unit on the top switch of the stack Power up the added modules Caution Do not cross connect two Avaya P330 switches with two Octaplane light colored cables If you wish to cross connect for redundancy use one light colored Octaplane cable and one black redundancy cable Figure 4 2 shows an incorrect connection Avaya P332MF User s Guide 21 Chapter 4 Installation and Setup Note You can build a stack of up to 10 Avaya P330 switches If you do not wish to stack all the switches in a single rack use long Octaplane cables to connect two physical stacks as shown in Figure 4 3 Figure 4 2 Incorrect Stack Connection
86. his parameter you will get the default entity of the stack Layer 2 session to the Master switch routerlatmlmgplwan optional The entity to which you want to open a session If you do not specify this parameter you will get the default entity of the specific module switch Layer 2 entity of the switch see Note below router Routing entity atm ATM entity mgp Media Gateway Precessor wan WAN access router entity Note Layer 2 commands are only available if you opena switch session with the Master switch Note When you usethe session command the security level stays the same terminal Use the terminal width and terminal length commands to set the width and length of the terminal display in characters The syntax for this command is terminal width length lt characters gt 40 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 clear screen ping The clear screen command clears the current terminal display The syntax for this command is clear screen Usethe ping command to send ICMP echo request packets to another node on the network The syntax for this command is ping host number host Host IP address Internet address of route destination If missing then the last host IP is used number Number of packets to send If missing then the last number is used If the last number is not available the default is 4 Note You can use this command via the Master switch
87. ia 31 70 414 8004 Croatia 31 70 414 8039 Cyprus 31 70 414 8005 Czech Rep 31 70 414 8006 Denmark 45 8233 2807 Egypt 31 70 414 8008 Estonia 372 6604736 Finland 358 981 710 081 Country Number France 33 1 4993 9009 Germany 49 69 95307 680 Ghana 31 70 414 8044 Gibraltar 31 70 414 8013 Greece 00800 3122 1288 Hungary 06800 13839 Iceland 0800 8125 Ireland 353 160 58 479 Israel 1 800 93 00 900 Italy 39 02 7541 9636 Jordan 31 70 414 8045 Kazakhstan 31 70 414 8020 Kenya 31 70 414 8049 Kuwait 31 70 414 8052 Latvia 371 721 4368 Avaya P332MF User s Guide 163 How to Contact Us Local Dial In Local Dial In Country Number Country Number Lebanon 31 70 414 8053 Slovakia 31 70 414 8066 Lithuania 370 2 756 800 Slovania 31 70 414 8040 Luxemburg 352 29 6969 5624 South Africa 0800 995 059 Macedonia 31 70 414 8041 Spain 34 91 375 3023 Malta 31 70 414 8022 Sweden 46 851 992 080 Mauritius 31 70 414 8054 Switzerland 41 22 827 8741 Morocco 31 70 414 8055 Tanzania 31 70 414 8060 Netherlands 31 70 414 8023 Tunisia 31 70 414 8069 Nigeria 31 70 414 8056 Turkey 800 4491 3919 Norway 47 235 001 00 UAE 31 70 414 8036 Oman 31 70 414 8057 Uganda 31 70 414 8061 Pakistan 31 70 414 8058 UK 44 0207 5195000 Poland 0800 311 1273 Ukraine 31 70 414 8035 Portugal 351 21 318 0047 Uzbekistan 31 70 414 8046 Qat
88. ies with the following standards IEEE e 802 3x Flow Control on all ports e 802 10 VLAN Tagging support on all ports and 802 1p compatible e 802 1D Bridges and STA e 8032z Gigabit Ethernet ports e 8032u Ethernet Fast Ethernet ports IETF e MIB II RFC 1213 e Bridge MIB for Spanning Tree RFC 1492 e RMON RFC 1757 e SMON RFC 2613 e Bridge MIB Groups RFC 2674 dotldbase and dot1dStp fully implemented Support for relevant MIB objects dot1q dot1gBase dotlqVlanCurrent Avaya P330 Network Management Comprehensive network management is a key component of today s networks Therefore we have provided multiple ways of managing the Avaya P330 to suit your needs Avaya P330 Device Manager Embedded Web The built in Avaya P330 Device Manager Embedded Web Manager allows you to manage an Avaya P330 stack using a Web browser without purchasing additional software This application works with the Microsoft Internet Explorer and Netscape Navigator web browsers and Sun Microsystems Java Plug in Avaya P330 Command Line Interface CLI The Avaya P330 CLI provides a terminal type configuration tool for local or remote configuration of Avaya P330 features and functions 2 Avaya P332MF User s Guide Chapter 1 Avaya P330 Overview Avaya Multi Service Network Manager When you need extra control and monitoring or wish to manage other Cajun Campus equipment then the Avaya Multi Service Network Manager network manage
89. igation Cursor Movement and Shortcuts 36 Embedded Web Manager Browser Compatability 140 Stacking Module tree ete te etes 148 Gigabit Ethernet Expansion Modules ssssssssssstsrtsrstrt1ese 148 Fiber Fast Ethernet Expansion Module 150 Ethernet Fast Ethernet Expansion Module 150 BR SADA Ss Bete DER atte Me ake 158 AT a ad 158 MTBF for the Avaya P332MF in Various Configurations 158 Avaya P332MF User s Guide xi List of Tables xii Avaya P332MF User s Guide Chapter 1 Avaya P330 Overview The Avaya P330 family of stackable Ethernet workgroup switches includes a range of modules with 10 100 1000 Mbps ports and a Layer 3 capability ATM Expansion Module The Avaya P332MF switch has 12x100BaseFX MT RJ ports and an Expansion Module slot The optional expansion modules provide additional Ethernet Fast Ethernet and Gigabit Ethernet connectivity An Avaya P330 stack can contain up to 10 switches and up to 3 backup power supply units The stacked switches are connected using the Avaya X330STK stacking Modules which plug into a slot in the back of the Avaya P330 They are connected using the X330SC or X330LC cable if the stack is split between two racks The Avaya X330RC cable connects the top and bottom switches in the stack and provides redundancy and hot swappability in the same way that modules can be swapped in a modular switching chassis The Avaya P3
90. iguration settings made to this switch e stack config file which contains the configuration settings made at the stack level for example IP address of the stack EW Archive file which contains the Device Manager Embedded Web software vernum S W Version number relevant only for the Device Management S W file type There are several file types file location file description e Running Conf the configuration currently in use and the startup configuration in the P330 ML P333R and P333R LB e SW Web Image Device Manager S W archive file Type of internal memory into which the file is loaded Description of the file Note If the N A is displayed for the EW_Archive file this means that the Device Manager S W is not loaded correctly Download the Device Manager S W again 80 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Privileged Level Commands Following is a table of the Privileged Level commands This level includes all the commands from the User Level described above see the User Level Commands Section for a description of these common commands no hostname Returns the prompt to its default Page 82 normon history Deletes an existing history entry Page 82 normon alarm Deletes an existing alarm entry Page 82 normon event Deletes an existing event entry Page 83 hostname Displays or sets a new prompt Page 83 clear Clears current settings Page 83 a group of commands e set
91. in a separate Table on Page 83 2 The set command corresponds to a group of commands and is shown in a separate Table on Page 88 3 The radius authentication commands corresponds to a group of commands listed on Page 132 no hostname Usethe no hostname command to return the CLI prompt to its default The syntax for this command is no hostname Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch no rmon history Usethe no rmon history command to delete an existing RMON history entry The syntax for this command is no rmon history History Index no rmon alarm Usethe no rmon alarm command to delete an existing RMON alarm entry The syntax for this command is no rmon alarm Alarm Index 82 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 no rmon event hostname Use the no rmon event command to delete an existing RMON event entry The syntax for this command is no rmon event lt Event Index gt Use the hostname command to change the Command Line Interface CLI prompt The current switch number always appears at the end of the prompt The syntax for this command is hostname lt hostname_string gt hostname string none displays current hostname string the string to be used as the hostname up to 20 characters Note If this command is to be implemented on a switch other than the stack mas
92. internal CLI The CLI is command line driven and does not have any menus To activate a configuration option you must type the desired command at the prompt and press Enter You can also configure your Avaya P330 using the P330 Manager with its graphical user interface For details see the Avaya P330 Device Manager Appendix and the Avaya Multi Service Network Manager P330 Device Manager User s Guide on the Documentation and Utilities CD Establishing a Serial Connection Perform the following steps to connect a terminal to the Avaya P330 Master Switch Console port for configuration of Stack or Router parameters 1 Use the serial cable supplied to attach the RJ 45 console connector to the Console port of the Avaya P330 Master Switch Connect the DB 9 connector to the serial COM port on your PC terminal 2 Ensure that the serial port settings on the terminal are 9600 baud 8 bits 1 stop bit and no parity 3 When you are prompted for a Login Name enter the default login The default loginis root 4 When you are promoted for a password enter the user level password root 5 Now you can begin the configuration of Module or Stack parameters Avaya P332MF User s Guide 31 Chapter 5 Avaya CLI Architecture Access amp Conventions Establishing a Telnet Connection Perform the following steps to establish a Telnet connection to the Avaya P330 for configuration of Stack or Router parameters You can Telnet either the Stack Master I
93. interval Page 120 e setself loop discovery Sets the IBM token ring discovery mode Page 121 Admin Status set welcome message Sets a welcome message to appear after Page 121 a reboot e setallowed managers Enables disables the Allowed Managers Page 122 enabled disabled feature e setallowed managers Used to add or remove an IP address Page 122 IP from the allowed managers table set psu type Sets the main power supply type AC Page 122 set logout DC of the module The set logout command is used to set the number of minutes until the system automatically disconnects an idle session The syntax for this command is set logout lt timeout gt timeout Number of minutes 0 to 999 until the system automatically disconnects an idle session Setting the value to O disables the automatic disconnection of idle sessions default is 15 minutes Output Example To set the number of minutes until the system disconnects an idle session Avaya P332MF User s Guide 91 Chapter6 CLI Layer 2 automatically P330 N4 set logout 20 Sessions will be automatically logged out after 20 minutes of idle time Output Example To disable the automatic disconnection of idle sessions P330 N4 set logout 0 Sessions will not be automatically logged out set timezone Usethe set timezone command to assign a timezone name and set the time difference of your P330 relative to the Coordinated Universal Time UTC GMT The mi
94. irror port 1 10 sampling always direction both Mirroring both Rx and Tx packets from port 1 9 to port 1 10 is enabled set port spantree Use the set port spantree command to enable or disable the spanning tree mode for specific switch ports The syntax for this command is set port spantree enable disable module port enable disable Enables or disables the spanning tree mode for the specified ports module port The switch port number Output Example Enable the spanning tree mode for port 2 on module 3 P330 N set port spantree enable 3 2 Avaya P332MF User s Guide 109 Chapter 6 CLI Layer 2 set port spantree priority Use the set port spantree priority command to set the priority level of a port This value defines the priority of a port to be blocked in case two ports with the same costs cause a loop The syntax for this command is set port spantree priority module port value module port The switch number the port number value Number representing the priority of the port The priority level is from 0 to 255 with 0 indicating high priority and 255 indicating low priority A port with a lower priority will be blocked set port spantree cost Use the set port spantree cost command to set the cost of a port This value defines which port will be allowed to forward traffic if two ports with different costs cause a loop The syntax for this command is set port spantree cost modu
95. l expansion slot B 329 19 46 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show download status show snmp Use the show download status command to display a summary of the last software download operation The syntax for this command is show download status slot Output Example P330 1 super 4 sh download status 1 Mod Bank Download State Activity Status Download Size 15 Bank B idle Download idle 0 Mod Version Host File I 3 5 18 149 49 70 61 d p340sw gt m1 3 5 18 p332gt_ml Note This command is only supported by the P332G ML and P332GT ML switches Use the show snmp command to display SNMP information The syntax for this command is show snmp Output Example P330 N gt show snmp Authentication trap disabled Community Access Community String read only public read write public trap public Trap Rec Address Traps Enabled Doel de config fault eto Avaya P332MF User s Guide 47 Chapter 6 CLI Layer 2 show snmp retries Usethe show snmp retries command to display the number of retries initiated by the Device Manager application when it tries to send SNMP messages to the device The syntax for this command is show snmp retries Output Example P330 N gt show snmp retries the SNMP Retries Number is 3 show snmp timeout show timeout show logout Use the show snmp timeout command to display the default SNMP timeout in seconds This command is us
96. le port value module port The switch number the port number value Number representing the cost The cost level is set from 1 to 65535 A lower cost lower value specifies precedence of a port to forward traffic 110 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set port security Usethe set port security command to enable MAC security on a port or a range of ports at the module level The port security is activated only after you enable the secutity mode at the stack level using the set security mode command Note This command is not supported in P332G ML and P332GT ML switches This command is used to set port security for ports in other P330 switches in the stack The syntax for this command is set port security enable disable lt module gt lt port gt enable disable Set the port security enable or disable module port The switch number the port number Output Example P330 N set port security enable 1 2 Port 1 2 secured set cascading Use the set cascading command to enable or disable fault trap sending for unconnected cascading links The default setting is disable The syntax for this command is set cascading up down fault monitoring enable disable lt mod num gt Output Example P330 N set cascading down fault monitoring enable 1 Module 1 cascading down fault monitoring enabled set inband vian Use the set inband vlan command to set a value
97. letes a link redundancy Page 106 on off entry setport redundancy Enables disables all the defined link Page 106 redundancy schemes setinternal buffering Sets internal buffering capacity to Page 107 maximum minimum setboot bank Configures the boot bank from which Page 107 the switch will boot setintermodule port Defines the stack s unique fast Page 108 redundancy redundancy scheme setintermodule port Clears the intermodule redundancy Page 108 redundancy off set port mirror Sets a port mirroring source destination Page 109 pair in the stack set port spantree Enables or disables the spanning tree for Page 109 switch ports set port spantree Sets the port spantree priority level Page 110 priority Avaya P332MF User s Guide 89 Chapter 6 CLI Layer 2 set port spantree cost set port security set cascading set inband vlan set vlan set port flowcontrol set port auto negotiation flowcontrol advertisement set trunk set leaky vlan set spantree set spantree priority set autopartition set license set ppp authentication incoming set ppp incoming timeout set ppp baud rate set web aux files url set intelligent multicast setintelligent multicast client port pruning time Sets the port spantree cost Enables MAC security on a range of ports Sets switch cascading fault monitoring mode Sets the management VLAN ID Creates VLANs Sets the flow control mode of a por
98. losed in square brackets and separated by a vertical bar e If you enter an alphanumeric string of two words or more enclose the string in inverted commas Avaya P332MF User s Guide Notes Cautions and Warnings Note Notes contain helpful information or hints or reference to material in other documentation Vv Caution You should take care You could do something that may damage equipment or result in loss of data Warning This means danger Failure to follow the instructions or warnings may result in bodily injury You should ensure that you are qualified for this task and have read and understood all the instructions II Avaya P332MF User s Guide Table of Contents Chapter 1 Chapter 2 Chapter 3 Chapter 4 NO I ECC Notice eap e SAS iei een itera eee petes I Conventions Used in the Documentation sse I CET isaeieetusne aa I Notes Cautions and Warnings een II Table Of Contents ees etre tie NN epe eid i Listof EE ix Lis Of MET xi Avaya P330 OvVerview aotism iure e deii 1 Avaya P390 Family Features er S ier 1 Avaya P330 Standards Supported 2 TEE A Reto RTT Te NC HP CARE CAR EO SIN 2 IE TE i iue O E PRISES 2 Avaya P330 Network Management sss 2 Avaya P330 Device Manager Embedded Web 2 Avaya P330 Command Line Interface CLD 2 Avaya Multi Service Network Manager M ooo ooooooo 3 Avaya P330 Netw
99. ly available if the network manager has placed the files on the local Web server Avaya P332MF User s Guide 143 Chapter 7 Installing the Embedded Web Manager Installing the On Line Help and Java Plug In on your Web Site e Note This procedure is optional Copying the help files and Java plug in to a local Web server allows users to access the on line help for the Embedded Manager and enables automatic installation of the Java plug in the first time the users tries to manage the device 1 Copythe emweb aux files directory from the Avaya P330 Documentation and Utilities CD to your local Web server Please refer to your Web server documentation for full instructions 2 Define the URL in the Avaya P330 using the following CLI command set web aux files url IP address directory name where IP address directory name is the location of the directory from the previous step Refer to Chapter 6 for further details of the command Documentation and Online Help Refer to the Avaya P330 Documentation and Utilities CD Software Download You can perform software download using the CLI or Avaya UpdateMaster part of the Avaya Multi Service Network Manager Suite 144 Avaya P332MF User s Guide AppendixA Specifications Avaya P332MF Switch Physical Height 2U 88 mm 3 5 Width 482 6 mm 19 Depth 450 mm 17 7 Weight 8 kg 17 6 Ib Power Requirements AC Input voltage 100 to 240 VAC 50 60 Hz Pow
100. managers 122 set allowed managers IP 122 set arp aging interval 120 set arp tx interval 120 set autopartition 116 set boot bank 107 set cascading 111 set inband vlan 111 set intelligent multicast 118 set intelligent multicast client port pruning time 118 set intelligent multicast group filtering delay time 119 set intelligent multicast router port pruning time 119 set interface 97 set interface ppp 98 set intermodule port redundancy 108 set intermodule port redundancy off 108 set internal buffering 107 set ip route 93 set leaky vlan 115 set license 116 set logout 91 set port auto negotiation flowcontrol ad vertisement 114 set port channel 104 set port classification 105 set port disable 100 set port duplex 101 set port enable 100 Avaya P332MF User s Guide Index of CLI Commands set port flowcontrol 112 set port level 99 set port mirror 109 set port name 102 set port negotiation 99 set port redundancy 106 set port redundancy on off 106 set port security 111 set port self loop discovery Admin_Status 104 set port spantree 109 set port spantree cost 110 set port spantree priority 110 set port speed 101 set port static vlan 103 set port trap 102 set port vlan 102 set port vlan binding mode 103 set ppp authentication incoming 117 set ppp baud rate 117 set ppp chap secret 136 set ppp incoming timeout 117 set psu type 122 set radius authentication 137 set radius authen
101. managers IP set psu type Use the set allowed managers IP command to add or remove an IP address from the Allowed Managers table The Allowed Managers table can contain up to twenty IP addresses The syntax for this command is set allowed managers ip add delete IP address Output Example P330 N P330 1 super set allowed managers ip add 149 49 32 134 Ip was added to the table Use the set psu type command to set the main power supply type AC DC of the module Note This command is not applicable to P332G ML and P332GT ML switches This command is used to set the power supply types for other P330 switches in the stack 122 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 The syntax for this command is set psu type AC DC module number Output Example P330 N gt set psu type DC 3 Power supply type was changed to DC on module 3 sync time Use the sync time command to synchronize the time used by all switches in a stack The syntax for this command is sync time Output Example P330 N sync time Time has been distributed get time Use the get time command to retrieve the time from the network The syntax for this command is get time Output Example P330 N get tim Time is already being acquired from network Avaya P332MF User s Guide 123 Chapter 6 CLI Layer 2 reset Use the reset command to restart the system or an individual switch
102. ment suite is the answer This suite provides the ease of use and features necessary for optimal network utilization e Avaya Multi Service Network Manager is available for Windows NT 2000 and Solaris 8 e Avaya Multi Service Network Manager can operate in Stand Alone mode with Windows NT 2000 e Avaya Multi Service Network Manager operates under HP OpenView for Windows NT 2000 and Solaris 8 Avaya P330 Network Monitoring RMON MIBs RFC 1757 RMON support for groups 1 2 3 and 9 Statistics History Alarms Events SMON MIBs RFC 2613 SMON support for groups Data Source Capabilities Port Copy VLAN and Priority Statistics Bridge MIB Groups RFC 2674 e dotldbase and dot1dStp fully implemented e Support for relevant MIB objects dotlg dotlqBase dot1qVlanCurrent Port Mirroring The Avaya P330 provides port mirroring for additional network monitoring functionality You can filter the traffic and mirror either incoming traffic to the source port or both incoming and outgoing traffic This allows you to monitor the network traffic you need Ports which are members in a Link Aggregation Group LAG cannot also be used as Port Mirroring Destination or Source ports Avaya P332MF User s Guide 3 Chapter 1 Avaya P330 Overview SMON The Avaya P330 supports Avaya s ground breaking SMON Switched Network Monitoring which the IETF has now adopted as a standard RFC2613 SMON p
103. nd is used to display the internal buffering status for the other P330 switches in the stack Avaya P332MF User s Guide 57 Chapter 6 CLI Layer 2 show boot bank show module Usethe show boot bank command to display the software bank from which the switch will boot at the next boot process This command should be issued separately for each switch in the stack using the session command Note This command is not supported by the P333R and P333R LB switches Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch The syntax for this command is show boot bank Output Example show boot bank Boot bank set to bank a Usethe show module command to display switch status and information For each switch with an expansion sub module installed both switch and expansion sub module type and information are shown The syntax for this command is show module lt mod_num gt mod num Optional Number of the switch expansion sub module If you do not specify a number all switches expansion sub modules are shown Output Example P330 N show port flowcontrol 3 2 Mod Type C S S N Statuses E P3337 1 0 4144162 PS OK Fans OK Mode Layer X330GT2 2 0 P330STK 2 0 Conn Up Fail Conn Down Ok BUPS BUPS Not Prsnt Fans None Type None 2 P333T PWR 3 0 4455428 PS OK Fans OK Mode Layer2 58 Avaya P332MF User s Guide Chapter 6 CL
104. nd press Enter e Note The terms module and switch are used interchangeably User Level Commands This section describes all commands that are available from the User level Following is a table of the User Level commands and command groups all commands are also available at the higher levels session terminal width terminal length clear screen show ping dir Opens a session to another P330 switch X330 ATM Access sub module X330 WAN Access sub module or G700 MGP Displays or sets the width of the terminal display Display or set the length of the terminal display Clears the current terminal display Shows the current switch parameters Sends ICMP echo request packets to another node on the network Show files in the system Page 40 Page 40 Page 40 Page 41 Page 42 Page 41 Page 79 1 This command corresponds to a group of commands and is shown in a separate Table on Page 42 Avaya P332MF User s Guide 39 Chapter 6 CLI Layer 2 session Usethe session command to open a session with a specific entity in a switch of the stack For example you can open a session with the Routing entity of a P332G ML switch in the stack or with an the X330 ATM sub module entity plugged into a specific switch The syntax for this command is session lt mod_num gt switch router atm mgp wan mod_num optional The switch number If you do not specify t
105. nk Box is the stack Master and the stack is in redundant mode The following Function LEDs apply to ports 1 to 66 OFF Port disabled LNK Port status ON Port enabled and link OK Blink Port enabled and the link is down Avaya P332MF User s Guide 9 Chapter 3 Avaya P332MF Front and Back Panels Table 3 1 Avaya P332MF LED Descriptions LED Name Description LED Status OFF No collision or FDX port COL Collision ON Collision occurred on line OFF No transmit activity Tx Transmit to line ON Data transmitted on line from the module OFF No receive activity Rx Receive from line ON Data received from the line into the module OFF Half duplex mode FDX Half Full Duplex ON Full duplex mode OFF No Flow Control FC Flow Control ON Symmetric Asymmetric Flow Control mode is enabled and port is in full duplex mode Hspd High Speed 10 100 1000 OFF 10 N A ON 100 1000 NE Link Aggregation OFF No LAG defined for this port Group Trunking ON Port belongs to a LAG Table 3 2 Avaya P330 lt gt Select buttons Description Function Left Right Individual select LED function see table above Reset module Press both right and left buttons together for approximately two seconds All LEDs on module light up until buttons are released Reset stack Press both right and left buttons together for
106. nsert the Module gently into the slot ensuring that the Printed Circuit Board PCB is aligned with the guide rails The PCB not the metal base plate fits into the guide rail Press the Module in firmly until it is completely inserted into the Avaya P330 4 Gently tighten the two screws on the front panel of the expansion module by turning the screws e gt y Note The expansion modules contain components sensitive to electrostatic discharge Do not touch the circuit board unless instructed to do so Avaya P332MF User s Guide 153 Appendix A Specifications Removing an Existing Expansion Module 1 Loosen the screws by turning the knobs 2 Grasp the two knobs one near each side of the front panel and pull gently but firmly towards yourself 3 Insert another expansion module or the blanking plate Note The Avaya P330 switch must not be operated with the expansion slot open the expansion module should be covered with the supplied blanking plate if necessary Note X330GT2 Modules are hot swapable and can be inserted or removed in an operating base unit Cabling A Category 5 copper cable with RJ 45 termination should be used You should use all eight wires in the cable The maximum copper cable length connected to a 1000Base T port is 100 m 328 ft 154 Avaya P332MF User s Guide Appendix A Specifications ATM Expansion Modules 4 9 There are three Avaya P330 ATM Expansion Modules e
107. nto which to download the data If Avaya Multi Service Network Manager is running an additional TFTP server is not required The syntax for this command is copy tftp EW_archive lt filename gt lt ip gt lt mod_num gt filename Embedded Web Manager image file name full path ip The ip address of the TFTP server mod_num Target switch number Example P330 N copy tftp EW_archive c p330 p330web201 192 168 49 10 5 copy tftp SW_image Use the copy tftp SW_image command to update the software image and the device manager applications of a designated switch To use this command you need to have an active TFTP server and to create a file into which to download the data If Avaya Multi Service Network Manager is running an additional tftp server is not required The syntax for this command is copy tftp SW_image lt image file gt EW_archive lt filename gt lt ip gt Avaya P332MF User s Guide 131 Chapter 6 CLI Layer 2 lt mod_num gt image file filename ip mod num Example P330 N copy tftp SW image c 1p3301p330web101 Common name for the files that contain the Software Image and Embedded Web archive full path Embedded Web Manager image file name full path The ip address of the TFTP server Target switch number c 1p3301p330web201 192 168 49 10 5 Radius Commands The following radius commands are accessible from Privileged mode set radius authentication secret
108. nutes parameter can only be set to 30 The syntax for this command is set timezone zone name hours hours min gt Output Example set timezone GMT 3 30 Timezone set to GMT offset from UTC is 3 30 hours Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york set time protocol Use the set time protocol command to set the protocol for use in the system as either SNTP protocol or TIME protocol The syntax for this command is set time protocol sntp protocol time protocol Output Example P330 N4 set time protocol sntp protocol The protocol has been set to SNTP protocol Output Example P330 N set time protocol time protocol 92 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 The protocol has been set to TIME protocol set time server The set time server command is used to set the TIME server address The syntax for this command is set time server lt ip gt ip IP address of the TIME server set time client The set time client command is used to enable or disable the periodic network time acquisition by the switch from the network time server SNTP or TIME protocol The syntax for this command is set time client lt enable disable gt set ip route Usethe set ip route command to add IP addresses to the IP routing table You can configure from one to ten 10 default gateways for a P330 s
109. o event 4 1054 On startup enable rising or falling alarms Avaya P332MF User s Guide 71 Chapter 6 CLI Layer 2 show rmon event Use the show rmon event command to show the parameters of an Event entry defined by the rmon event command on Page 128 or using the P330 Device Manager The syntax for this command is show rmon event lt Event Index gt Output Example P330 N gt show rmon event 1054 event Event 1054 is active owned by amir Description is event for monitoring amir s co Event firing causes log and trap to community public last fired 0 0 0 show ppp session Use the show ppp session command to display PPP parameters and statistics of a currently active PPP session The syntax for this command is show ppp session Example P330 N show ppp session show ppp authentication Usethe ppp authentication command to see the authentication method used for PPP sessions The syntax for this command is show ppp authentication Output Example P330 N show ppp authentication PPP Authentication Parameters Incoming CHAP 72 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show ppp incoming timeout Usetheppp incoming timeout command to see the amount of time in minutes that a PPP session can remain idle before being automatically disconnected The syntax for this command is show ppp incoming timeout Output Example P330 N show ppp incoming timeout P
110. ommand is clear snmp trap lt rcvr_addr gt all rcvr addr IP address or IP alias of the trap receiver the SNMP management station to clear all Keyword that specifies every entry in the SNMP trap receiver table Output Example P330 N clear snmp trap 192 122 173 82 SNMP trap receiver deleted 84 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 clear vlan Usethe clear vlan command to delete an existing VLAN and return ports from this VLAN to the default VLAN 1 When you clear a VLAN all ports assigned to that VLAN are assigned to the default VLAN 1 The syntax for this command is clear vlan vlan id name lt vlan_name gt vlan_id Number of the VLAN range is 1to 3071 vlan_name VLAN name Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Output Example To delete an existing VLAN VLAN 5 from a management domain P330 N clear vlan 5 name V5 This command will assign all ports on vlan 5 to their default in the entire management domain do you want to continue Y N y All ports on vlan id 5 assigned to default vlan VLAN 5 was deleted successfully clear dynamic vlans Use the clear dynamic vlans command to clear dynamic vlans Only the VLANs learned by the switch from incoming traffic are cleared using this command The syntax for this command is clear dynamic vlans Output Example
111. only Output Example To ping the IP number 149 49 48 1 four times P330 N gt ping 149 49 48 1 4 PING 149 49 48 1 56 data bytes 64 bytes from 149 49 48 1 icmp_seq 0 time 0 ms 64 bytes from 149 49 48 1 icmp seg l time 0 ms 64 bytes from 149 49 48 1 icmp_seg 2 time 0 ms P330 1 super 64 bytes from 149 49 48 1 icmp seq 3 time 0 ms 149 49 48 1 PING Statistics 4 packets transmitted 4 packets received 0 packet loss round trip ms min avg max 0 0 0 Avaya P332MF User s Guide 41 Chapter 6 CLI Layer 2 Show Commands Summary Table Following is a table ofthe show commands show time show timezone show time parameters show ip route show image version show download status show snmp show snmp retries show snmp timeout show timeout show logout show interface show device mode show port show port trap show port channel show port classification show port redundancy show intermodule port redundancy show port mirror show port vlan binding mode show port security show port blocking Shows the current time Shows the current timezone offset Shows the status and parameters Shows the IP routing table entries Shows the image version Shows the last download operation Shows the SNMP community strings Shows the SNMP retries number Shows the SNMP timeout Shows the CLI logout time setting Shows the CLI logout time setting Shows the interf
112. ords or more enclose the string in inverted commas e Information displayed on screen is displayed in text font Avaya P332MF User s Guide 35 Chapter 5 Avaya CLI Architecture Access amp Conventions Navigation Cursor Movement and Shortcuts The CLI contains a simple text editor with these functions Table 5 1 Navigation Cursor Movement and Shortcuts Keyboard Functions Backspace Deletes the previous character Up arrow Down arrow Scrolls back and forward through the command history buffer Left arrow Right arrow Moves the cursor left or right Tab Completes the abbreviated command Type the minimum number of characters unique to the command An exception is the Reset System command which you must type in full Enter Executes a single line command uu If you type a name with quotation marks the marks are ignored Getting Help On line help may be obtained at any time by typing a question mark or the word help on the command line or by pressing the F1 key To obtain help for a specific command type the command followed by a space and a question mark Example Router show Command Syntax Commands are not case sensitive That is uppercase and lowercase characters may be interchanged freely Command Abbreviations All commands and parameters in the CLI can be truncated to an abbreviation of any length as long as the abbreviation is not ambiguous For example
113. ork Monitoring ee 3 RMON MIBs REC 1757 aa aaa nennen rennen enne ense nnne nn 3 SMON MIBs RFC 2613 7 4 eese nennen nennen nennen 3 Bridge MIB Groups REC 2674 een 3 Port MitfOTIfig ass ede ge ge atts P ER ed ec nt ia fee e tena 3 SIMON ee ee A EE E 5 Application an BEN NS tos 5 Applic tioti2 aiii int aite e NN NN 6 Application Satriani e ee eine deines 7 Avaya P332MF Front and Back Panels ue 8 Avaya P332MF Front Padel nicas 8 Avaya P390 Back E EE 12 BUES Input Connector i aine eroe eed ene hort 12 Installation and Setup invicta ee eerte i hne 19 Installing the X330STK Stacking Sub module in the P330 19 Avaya P332MF User s Guide Table of Contents Chapter 5 Chapter 6 POSIUODITIgz ei tre neq han in id TER an 19 Rack Mounting et ed terere ient teneri fei ear Ste en 20 Connecting Stacked Switches sss 21 To connect stacked switches sse 21 Installing Expansion Sub modules sse eee 24 Installing the Expansion Sub module into the Avaya P330 24 Removing an Existing Expansion Sub module ooooooooooo 24 Powering On Avaya P330 Module AC 25 Powering On Avaya P330 Module DC ee 25 Configuring the Switch EE 26 Avaya P330 Default Settings ee 26 arii a UN UR 28 Connecting the Console Cable o oooooocoooooocc 29 Configuring the Terminal Serial Port Parameters 29 Connecting
114. port auto negotiation flowcontrol advertisement lt mod_num gt port num no flowcontrol asym tx only sym only sym and asym rx no flowcontrol The port will advertise no pause capabilities asym tx only The port will advertise asymmetric Tx pause capabilities only sym only The port will advertise symmetric pause capabilities only sym and asym rx The port will advertise both symmetric and asymmetric Rx pause capabilities Output Example P330 N set port auto negotiation flowcontrol advertisement 1 5 asym tx only P330 N4 Port 1 5 pause capabilities was set set trunk Usethe set trunk command to configure the tagging mode of a post set trunk module port value module port module port number value off dotlg Output Example P330 1 super set trunk 2 20 dotlg Dot1Q VLAN tagging set on port 2 20 114 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set leaky vlan Use the set leaky vlan command to define the P330 stack s leaky VLAN mode In this mode VLAN test is done only on broadcast multicast unknown frames and not on unicast frames The syntax for this command is set leaky vlan lt enable disable gt Output Example P330 N set leaky vlan enabl Leaky VLAN mode enabled set spantree Usethe set spantree command to enable disable the spanning tree protocol for the stack Note When you disable STP blocking ports are disabled in order to prevent loops in the network As a result
115. port will not send flow control frames to the far end Receive flow control administration Possible settings e ON indicates that the local port will act upon flow control indications if received from the far end OFF indicates that the local port will discard flow control frames if received from the far end Receive flow control operation mode Possible modes ON indicates that the local port will act upon flow control indications received from the far end OFF indicates that the local port will discard flow control frames received from the far end Avaya P332MF User s Guide 61 Chapter6 CLI Layer 2 show cam Usethe show cam commands to display the CAM table entries for a specific port ER Note MACS associated with LAGs appear under the LAG ID not under the LAG port The syntax for this command is show cam mac mac addr module port Output Example P330 N show cam 1 1 Dest MAC Route Dest Destination Ports 00 40 0d 59 03 78 1 1 00 d0 79 0a 0a da 1 1 00 40 0d 43 1 9 1 1 Gic Output Example P330 N show cam mac 00 40 0d 88 06 c8 Dest MAC Route Dest Destination Ports 00 40 0d 88 06 c8 LAL Total Matching CAM Entries Displayed 1 show cascading fault monitoring Use the show cascading fault monitoring command to display the status of the fault trap sending mode for cascading links The syntax for this command is show cascading fault monitoring lt mod_num gt
116. r set radius authentication server 192 168 38 12 primary clear radius authentication server Use the clear radius authentication server command to remove a primary or secondary RADIUS authentication server The syntax for this command is clear radius authentication server primary secondary Avaya P332MF User s Guide 133 Chapter 6 CLI Layer 2 set radius authentication retry time Use the set radius authentication retry time command to set the time to wait before re sending an access request The syntax for this command is set radius authentication retry time lt time gt time Retry time in seconds set radius authentication retry number Use the set radius authentication retry number command to set the number of times an access request is sent when there is no response The syntax for this command is set radius authentication retry number lt number gt number Retry number set radius authentication udp port Usethe set radius authentication udp port command to set the RFC 2138 approved UDP port number Normally the UDP port number should be set to its default value of 1812 Some early implementations of the RADIUS server used port number 1645 The syntax for this command is set radius authentication server udp port lt number gt 134 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 Supervisor Level Commands username no username This level includes all the commands of th
117. rovides an unprecedented top down monitoring of switched network traffic at the following levels e Enterprise Monitoring e Device Monitoring e VLAN Monitoring e Port level Monitoring This top down approach gives you rapid troubleshooting and performance trending to keep the network running optimally Note Avaya Multi Service Network Manager is required to run SMON monitoring Note You need to purchase one SMON License per Avaya P330 Stack Avaya P332MF User s Guide Chapter 2 Applications The following sections describe typical applications for the Avaya P330 in a network with other Cajun Campus products Application 1 This application shows Avaya P882 as the network backbone with Avaya P333T and Avaya P334T stacks as closet devices with LAG and redundant links Figure 2 1 Avaya P333T and Avaya P334T stacks with an Avaya P882 Backbone 10 100 Mbps Ethernet J ze mm pe sess sesos E Avaya P333T Avaya P333T Avaya P334T Avaya P334T Avaya P334T Avaya P334T Avaya P334T Avaya P333T Avaya P334T Gigabit Ethernet with LAG LAS Gigabit Ethernet with LAG Avaya P882 4x100 Mbps LAG Avaya P332MF User s Guide 5 Chapter 2 Applications Application 2 This application shows an Avaya P330 stack forming the backbone of a Small Medium sized Enterprise SME network with Avaya P330 stacks as closet devices with LAN and redundant links Figure
118. rt channel port list value name port list Switch and ports to bundle format module port value on off to enable disable a channel for the specified module ports 104 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 name Channel name Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york Output Example P330 1 super set port channel 1 1 3 on test Port 1 1 channel mode set to on Port 1 2 was added to channel Port 1 3 was added to channel set port classification Use the set port classification command to set the port classification to either regular or valuable Any change in the Spanning Tree state from Forwarding for a valuable port will erase all learnt MAC addresses in the stack The syntax for this command is set port classification module port regular valuable module port switch port range regular valuable port classification Output Example P330 1 super set port classification 2 19 valuable Port 2 19 classification has been changed Avaya P332MF User s Guide 105 Chapter 6 CLI Layer 2 set port redundancy on off Usethe set port redundancy command to define delete port redundancy schemes between a Primary and a Secondary link There should not be any redundancy scheme already defined on any of the links The syntax for this command is set port redundancy mod num prim po
119. rt num mod num second port num on off redundancy name prim port num Primary link of the redundancy scheme second port num Secondary link of the redundancy scheme redundancy name Name for the redundancy scheme optional Output Example P330 N4 set port redundancy 1 7 2 12 on redl uplink Port 2 12 is redundant to port 1 7 Port redundancy is active entry is effective immediately Note If you wish to define a name which includes spaces you must enclose the entire name in quotation marks e g new york set port redundancy Usethe set port redundancy commands to activate or disable all defined port redundancy schemes within the stack This command will not delete existing port redundancy entries A port redundancy scheme is removed once the switch containing either its primary or secondary ports is removed from the stack Note You must disable Spanning Tree before you can enable redundancy The syntax for this command is set port redundancy enable disable Output Example P330 N4 set port redundancy enable All redundancy schemes are now enabled 106 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set internal buffering The set internal buffering command allows you to set the size either Maximum or Minimum of the Receive Rx buffer allocated to each port of the specified switch This command is meaningless when any port of the switch is operating with flow con
120. rval The syntax for this command is show arp tx interval Output Example P330 N show arp tx interval ARP tx interval is set to 5 seconds show arp aging interval Use the show arp aging interval command to display the ARP table aging interval for gateways entries Avaya P332MF User s Guide 77 Chapter6 CLI Layer 2 The syntax for this command is show arp aging interval Output Example P330 N gt show arp aging interval ARP table aging interval for gateways was set to 10 minutes show self loop discovery Use the show self loop discovery command to display a switch s IBM token ring cable discovery status Note This command is not supported by the P330 ML switches Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch The syntax for this command is show self loop discovery mod num Output Example P330 N show self loop discovery 1 Self Loop Discovery is disabled on module 1 show allowed managers status Usethe show allowed managers status command to display the activation status of the Allowed Managers feature When this feature is enabled only those stations whose IP addresses are listed in the Allowed Managers table can access the device over Telnet SNMP or HTTP The syntax for this command is show allowed managers status Output Example P330 N show allowed managers status Manag
121. s 2 104 set port channel Lean Ste dnte ter peer fete rena 104 set port classification EE 105 set port redundancy on off ee 106 set portredundancy ah hana ene cn die tlah 106 set internal buffering oom men ttt teet 107 SEEDOOUDANK Ze gege irte tice ee cet tree eet ve i eee E 107 set intermodule port redundancy sss 108 set intermodule port redundancy off ee 108 Set port A SEN NN NN 109 set port spantree En 109 Set port spantree priority e sss 110 set port spantree Coste 110 set port security ien Ete nee ehe eed 111 Set CASCA GING EE 111 setanband vla n s iot een sd RSS 111 SOE VAIN E te oet ce e ne e uda 112 set port flowcontrol oom 112 set port auto negotiation flowcontrol advertisement 114 EE 114 Sel Vd t te ias 115 set spantree A e RR NS SNN tian 115 set spantree priority En 115 Avaya P332MF User s Guide v Table of Contents Ee Ee Marita a 116 Seb Ticense c sn eene Ee i eee 116 set ppp authentication incoming oo 117 set ppp incoming timeout EE 117 setippp baud Tate deiere cotter Aa Naa 117 set web aux files url essent 118 set intelligent multicast ue 118 set intelligent multicast client port pruning time 118 set intelligent multicast router port pruning time 119 set intelligent multicast group filtering delay time 119 Seb Secure MAC Jona eroi inei e ein Kana nan un duh 119 Set Security MOE c conan rare ete e petrae re
122. stet mm 120 set arp aging interval ENEE 120 setarp tx interval do dente EEN 120 set self loop discovery Admin Status 2 121 set welcome message ENEE 121 set allowed managers ENEE 122 set allowed managers IP 122 set psu type iie senescere ten ret e eeu NN 122 cuu Cd Ho 123 e q APOCO nee eei e iet eet 123 TeSeb ss a ee ted eed ceci tes see Ad Ba 124 feset stack eo eee rece Re SNN NN 124 A M races 125 reset Wan ni Eu nee itecto egre Eb a AN 125 TAM Eet EE x aee unnm 125 FMON histOEy eee ee et en re Eee t ever en 126 ee E EE 127 TMOT EV EME laica ANN Nu NN 128 copy stack config tftp ooooooooooonnnnaana 128 copy module config tftp ENEE 129 copy tftp stack config ENEE 130 copy tftp module config ENEE 130 Copy ttp EW archiye c et anne mann hah an NN 131 copy tftp 5W IMAGE oe ee Pte thee uan lala 131 Radi s Commands ott Ert ester eene en na 132 set radius authentication secret oWoWoWoWoo 133 set radius authentication server ocooomoooom 133 clear radius authentication server oooooo oo 133 set radius authentication retry ti ME 134 set radius authentication retry number ooooooooooo 134 set radius authentication udp port o ooooooooo 134 Supervisor Level Commands Siia i 135 USO A A E uve ehe ae a eue eese eee me ver eei doped 135 vi Avaya P332MF User s Guide Table of Contents nO sernatne etra H
123. t Sets the flowcontrol advertising capabilities of a Gigabit port Sets the tagging mode of a port Enables disables leaky VLAN mode Enables disables Spanning Tree Protocol STP Sets the STP Bridge priority level Enables or disables autopartitioning for switches in a stack Enters a license number for the stack Defines the PPP authentication method Sets the time after which the system automatically disconnects an idle PPP incoming session Sets the baud rate used in PPP sessions Sets the location URL directory of the P330 Device Manager Help files Enables or disables the IP multicast filtering application Sets the aging time for client ports Page 110 Page 111 Page 111 Page 111 Page 112 Page 112 Page 114 Page 114 Page 115 Page 115 Page 115 Page 116 Page 116 Page 117 Page 117 Page 117 Page 118 Page 118 Page 118 90 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 setintelligent multicast Sets the aging time for router ports Page 119 router port pruning time setintelligent multicast Sets the time delay before a filter is Page 119 group filtering delay applied to a specific group time setsecure mac Adds a unicast MAC address into the Page 119 CAM table of a secured port setsecurity mode Enables or disables the stack s MAC Page 120 security e setarp aging interval Sets the ARP aging interval Page 120 setarp bcinterval Sets the keep alive
124. t will be notified if the lower threshold is passed The instances in which the alarm will be activated The possible parameters are Rising Falling risingOrfalling Owner name string P330 N rmon alarm 1026 1 3 6 1 2 1 16 1 1 1 5 1026 60 delta rising threshold 10000 1054 falling threshold 10 1054 risingOrFalling amir Avaya P332MF User s Guide 127 Chapter 6 CLI Layer 2 rmon event alarm 1026 was created successfully Usethe rmon event command to create an RMON event entry The syntax for this command is rmon event Event Number type description description owner owner event number This is the event index number of this entry type The type of the event The possible parameters are trap log logAndTrap none description A user description of this event owner Owner name string Output Example P330 N rmon event 1054 logAndTrap description event for monitoring amir s computer owner amir event 1054 was created successfully copy stack config tftp Usethe copy stack config tftp command to upload the stack level parameters from the current NVRAM running configuration into a file via TFTP Note Create the file into which you wish to upload the stack level parameters prior to executing this command The syntax for this command is copy stack config tftp filename ip filename The file name full path ip The IP address of the TFTP server Output Example P330 N4
125. tack The syntax for this command is set ip route destination gateway destination IP address of the network or specific host to be added gateway IP address of the router Output Example This example shows how to add a default route to the IP routing table P330 N set ip route 0 0 0 0 192 168 1 1 destination 0 0 0 0 gateway 192 168 1 1 ROUTE NET TABLE destination gateway flags Refcnt Use Interface 0 0 0 0 182 158 1 1 1 1 3199 se0 127 1 1 0 ID ele LT 1 8 7606 sel Avaya P332MF User s Guide 93 Chapter 6 CLI Layer 2 ROUTE HOST TABLE destination gateway flags Refcnt Use Interface 127 0 0 1 1210 05 5 2 131 100 10 10 1010 192 168 1 1 7 0 0 se0 set snmp community set snmp trap Use the set snmp community command to set or modify the switch s SNMP community strings The syntax for this command is set snmp community lt access_type gt community string access type read only read write or trap Output Example P330 1 super set snmp community read only read SNMP read only community string set Use the set snmp trap commands to add an entry into the SNMP trap receiver table and to enable or disable the different SNMP traps for a specific receiver First add the rcvr addr and then enable disable the different traps for it The syntax for this command is set snmp trap lt rcvr_addr gt set snmp trap rcvr addr enable disable all config fault enable
126. tatically bound show port security Usethe show port security command to list the security mode of the ports of a switch or stack When no port number is specified this command displays all the secured ports in the stack The syntax for this command is show port security lt module gt lt port gt Example P330 N show port security 1 Port 1 1 port security disabled Port 1 2 port security disabled Port 1 3 port security disabled Port 1 4 port security disabled Port 1 5 port security disabled ete Note Port security for the P330 ML switches will always have the value unknown This command is used to display the security status for the other P330 switches in the stack 54 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show port blocking Usethe show port blocking command to display the port blocking mode on a play tne p 8 particular switch Use the session command to change switches before using this command The show port blocking command is used with the show self loop discovery command to confirm a port s blocking mode The syntax for this command is show port blocking Note This command is not supported by the P330 ML switches Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch Avaya P332MF User s Guide 55 Chapter 6 CLI Layer 2 Output Example P330 N
127. telligent multicast hardware support configuration The syntax for this command is show intelligent multicast hardware support Output Example P330 N show intelligent multicast hardware support Intelligent multicast HW configuration Module Sub Module Cascade Support IPMc Not Installed Support IPMc show security mode Usethe show security mode command to display the status of the MAC security feature Note Layer 2 commands are only available if you opena switch session with the Master switch The syntax for this command is show security mode Output Example P330 N show security mode Security mode enabled 76 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 show secure mac port Usethe show secure mac port command to display the secure MAC addresses of a port from the sub agent CLI This command is accessed only through connection to a particular switch Note This command is not supported by the P330 ML switches Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch The syntax for this command is show secure mac port lt module gt port Output Example P330 N show secure mac port 1 Port Secure Src Addrs 1 17 00 50 04 07 6a fa 01 02 03 04 05 06 show arp tx interval Use the show arp tx interval command to display the keep alive frames transmission inte
128. ter a session should be opened to the relevant switch Clear Commands Summary Table Following is a Table of the Privileged Level clear commands clear timezone Returns the timezone to its default UTC Page 84 clear ip route Clears IP routing table entries Page 84 clear snmp trap Clears SNMP trap on the system Page 84 clear vlan Clears VLAN entries Page 85 clear dynamic vlans Clears dynamic VLAN entries Page 85 clear port static vlan Clears a VLAN statically configured ona Page 86 port clear cam Clears all the CAM entries Page 86 clear log Clears the Log entries of a switch Page 86 clear port mirror Cancels port mirroring Page 86 clear secure mac Clears a MAC address Page 87 Avaya P332MF User s Guide 83 Chapter 6 CLI Layer 2 clear timezone Returns the timezone to its default Coordinated Universal Time UTC The syntax for this command is clear timezone clear ip route Usethe clear ip route command to delete IP routing table entries The syntax for this command is clear ip route destination gateway destination IP address of the network or specific host to be added gateway IP address of the router Output Example To delete the route table entries using the clear ip route command P330 N clear ip route 134 12 3 0 192 1 1 1 Route deleted clear snmp trap Use the clear snmp trap command to clear an entry from the SNMP trap receiver table The syntax for this c
129. ter 6 CLI Layer 2 Example P330 N4 set port static vlan 1 4 6 9 set port self loop discovery Admin_Status Use the set port self loop discovery Admin_Status command to enable or disable a port s IBM token ring discovery mode The port s self loop discovery feature is activated only after you enable the self loop discovery mode at the module level using the set self loop discovery Admin status command Note This command is not supported by the P330 ML switches The syntax for this command is set port self loop discovery Admin Status lt enable disable gt lt module port gt Output Example P330 N4 set port self loop discovery Admin Status enable 1 2 Self Loop Discovery enabled on port 1 2 set port channel Usethe set port channel command to enable or disable a Link Aggregation Group LAC interface on the switch LAG creation requires a LAG name to be specified There is no default name You can also add or remove a port from an existing LAG When adding or removing a port to an existing LAG type the same LAG name All ports in the LAG are configured with the parameters of the first port that is added to the LAG These parameters include port administrative status speed duplex autonegociation mode VLAN ID tagging mode binding mode and priority level The ports added to a LAG must belong to the same LAG group refer to the LAG marking on device s front panel The syntax for this command is set po
130. the CLI to assign the P330 stack an IP address and net mask The network management station can establish communications with the stack once this address had been assigned and the stack has been inserted into the network To assign a P330 IP stack address 1 Establish a serial connection by connecting a terminal to the Master P330 switch of the stack 2 When prompted for a Login Name enter the default name root 3 When you are prompted for a password enter the password root You are now in Supervisor Level 4 Atthe prompt type set interface inband lt vlan gt ip address lt netmask gt Replace vlan ip address and lt netmask gt with the VLAN IP address and net mask of the stack 5 Press Enter to save the IP address and net mask 6 At the prompt type reset and press Enter to reset the stack After the Reset log in again as described above 7 Atthe prompt type set ip route dest gateway and replace dest and gateway with the destination and gateway IP addresses 8 Press Enter to save the destination and gateway IP addresses 30 Avaya P332MF User s Guide Chapter 5 Avaya CLI Architecture Access amp Conventions This chapter describes the Avaya P330 CLI architecture and conventions and provides instructions for accessing the Avaya P330 for configuration purposes The configuration procedure involves establishing a Telnet session or a serial connection and then using the Avaya P330 s
131. the COL LED is illuminated then all Port LEDs show the collision status of their respective port If you wish to select the LAG function then press the right button until the LAG Function LED is lit if you then wish to select Rx then press the left button several times until the Rx function LED lights Figure 3 1 shows the Avaya P332MF front panel Figure 3 2 shows a detailed view of the LEDs described in Table 3 1 pushbuttons the Expansion Module slot and the RJ 45 console connector at the bottom right Figure 3 1 Avaya P332MF Front Panel Avaya P332MF User s Guide 8 Chapter 3 Avaya P332MF Front and Back Panels Figure 3 2 Avaya P332MF LEDs Port LEDs 51 2 53 54 Eb 58 a es 3 4 5 6 7 8 9 10 11 12 qp PRA O0000000 000000000000 LA b Nao 000000007 000000000000 59 60 61 62 63 64 SS cr IA EG e uu FV Left RIght a gg and Reset both FIV Switch Function LEDs Switches D Note All LEDs are lit during a reset Table 3 1 Avaya P332MF LED Descriptions LED Name Description LED Status OFF power is off PWR Power status ON power is on Blink using BUPS only OFF Module is booting OPR CPU operation ON Normal operation OFF Module is a slave in a stack ON Module is the Master of the stack and the Octaplane and Redundant cable are SYS System Status connected correctly This LED will also light in Standalone mode Bli
132. the United States 4x eerte tine iet iste NA 163 In the EMEA Europe Middle East and Africa Region 163 In the AP Asia Pacific Region sess eee 165 In the CALA Caribbean and Latin America Region 165 viii Avaya P332MF User s Guide List of Figures Figure 2 1 Avaya P333T and Avaya P334T stacks with an Avaya P882 Backbone nit Be REKENING NN 5 Figure 2 2 Avaya P330 stacks with an Avaya 330 backbone 6 Figure 2 3 Avaya P332MF with an Avaya P882 backbone 7 Figure3 1 Avaya P332MF Front Panel oooooooooo 8 Figure3 2 Avaya P332MF LEDS REENEN 9 Figure 3 3 Avaya P330 AC and DC Back Panels oooooooo oo 12 Figure3 4 BUPS Input Connector Sticker e 12 Figure4 1 Avaya P330 Rack Mounting NEEN 20 Figure42 Incorrect Stack Connection sese eee 22 Figure 4 3 Avaya P330 Stack Connections sss 23 Figure7 1 The Welcome Page 141 Figure 7 2 Web based Manager sss eene 142 Avaya P332MF User s Guide ix List of Figures Avaya P332MF User s Guide List of Tables Table 3 1 Table 3 2 Table 4 1 Table 4 2 Table 4 3 Table 5 1 Table 7 1 Table A 1 Table A 2 Table A 3 Table A 4 Table A 5 Table B 6 Table B 7 Avaya P332MF LED Descriptions oocc 9 Avaya P330 lt gt Select buttons 10 Default Switch Settings ENEE 26 Default Port Settings eege EES 27 Gigabit Ethernet Cabling sess 28 Nav
133. the back panel of the AC switch top and the DC switch bottom with a stacking sub module installed BUPS Input Connector The BUPS input connector see Figure 3 4 is a 5 VDC connector for use with the Avaya P330 BUPS unit only A BUPS Input sticker appears directly to the right the BUPS input connector Figure 3 4 BUPS Input Connector Sticker WV BUPS Input 12 Avaya P332MF User s Guide Chapter 3 Avaya P332MF Front and Back Panels Avaya P332MF User s Guide 13 Chapter 3 Avaya P332MF Front and Back Panels 14 Avaya P332MF User s Guide Chapter 3 Avaya P332MF Front and Back Panels Avaya P332MF User s Guide 15 Chapter 3 Avaya P332MF Front and Back Panels 16 Avaya P332MF User s Guide Chapter 3 Avaya P332MF Front and Back Panels Avaya P332MF User s Guide 17 Chapter 3 Avaya P332MF Front and Back Panels 18 Avaya P332MF User s Guide Chapter 4 Installation and Setup The Avaya P332MF is ready to work after you carry out the installation instructions given below All the Avaya P332MF ports provide complete connectivity and no configuration is required to make the system work Installing the X330STK Stacking Sub module in the P330 V Caution The stacking sub modules contain components sensitive to electrostatic discharge Do not touch the circuit board unless instructed to do so To install the stacking sub module in the Avaya P330 1 2 Remove th
134. tication retry number 134 set radius authentication retry time 134 set radius authentication secret 133 set radius authentication server 133 set radius authentication udp port 134 set secure mac 119 set security mode 120 set self loop discovery Admin Status 121 set snmp community 94 set snmp retries 95 set snmp timeout 96 set snmp trap 94 set snmp trap auth 95 set spantree 115 set spantree priority 115 set system contact 96 set system location 96 set system name 96 set time client 93 set time protocol 92 set time server 93 set timezone 92 set trunk 114 set vlan 112 set web aux files url 118 set welcome message 121 show allowed managers status 78 show allowed managers status 78 show allowed managers table 79 show arp aging interval 77 show arp tx interval 77 show autopartition 67 show boot bank 58 show cam 62 show cascading fault monitoring 62 show image version 46 show intelligent multicast 75 show intelligent multicast hard ware sup port 76 show interface 49 show intermodule port redundancy 53 show internal buffering 57 show ip route 46 show leaky vlan 65 show license 68 show log 67 show module 58 show module identity 68 show port 50 show port auto negotiation flowcontrol advertisement 63 show port blocking 55 160 Avaya P332MF User s Guide Index of CLI Commands show port channel 51 tech 137 show port classification 52 terminal 40 show port flowcontrol 60 username
135. trol ON e Note This command is not supported by P332G ML and P332GT ML switches The syntax for this command is set internal buffering mod num max med min max Sets the internal receive buffer to its maximum size med Sets the internal receive buffer capacity dynamically min Sets the internal receive buffer to its minimum size this is the Default Example P330 N set internal buffering 1 max Done set boot bank Usethe set boot bank command to configure the software bank from which the switch will boot at the next boot process This command should be issued separately for each switch in the stack using the session command Note This command is not supported by the P333R and P333R LB switches Note If this command is to be implemented on a switch other than the stack master a session should be opened to the relevant switch The syntax for this command is set boot bank value value bank a bank b Avaya P332MF User s Guide 107 Chapter6 CLI Layer 2 Output Example P330 1 super set boot bank bank a Boot bank set to bank a setintermodule port redundanc y Use the set intermodule port redundancy command to define or delete the stack s unique intermodule redundancy scheme The defined scheme can be cleared using the set intermodule port redundancy off command The syntax for this command is set intermodule port redundancy module prim port module second port
136. vice The syntax for this command is set snmp retries lt number gt Avaya P332MF User s Guide 95 Chapter 6 CLI Layer 2 set snmp timeout Usethe set snmp timeout command to set the SNMP timeout in seconds This command is useful for access using the Device Manager The syntax for this command is set snmp timeout lt number gt set system location Usethe set system location command to set the mib2 system location MIB variable The syntax for this command is set system location lt string gt string Location name The location name is cleared if this field is left blank A string of 2 words or more must be type in quotation marks e g Operations Floor set system name Usethe set system name command to set mib2 system name MIB variable The syntax for this command is set system name lt string gt string System name The system name is cleared if this field is left blank A string of 2 words or more must be type in quotation marks e g Backbone Stack set system contact Usethe set system contact command to set mib2 system contact MIB variable The syntax for this command is set system contact lt string gt string Contact person The contact person field is cleared if this field is blank A string of 2 words or more must be type in quotation marks e g Yigdal Naouri 96 Avaya P332MF User s Guide Chapter 6 CLI Layer 2 set device mode Usethe set devi
137. wiring Agency Approvals EMC Emissions Approved according to US FCC Part 15 Subpart B Class A EU EN55022 Class A EU EN61000 3 2 146 Avaya P332MF User s Guide Appendix A Specifications Interfaces Japan VCCI A Immunity Approved according to EN55024 EU EN61000 3 3 Other Approved according to CLEI Code According to Tecordia Bellcore KS 22022 Standard NEBS Level 3 AC Product with optional brackets DC Product certified 12 x 100BASE FX MT RJ port connectors RS 232 for terminal setup via RJ45 connector on front panel Standards Compliance The Avaya P330 complies with Basic MTBF IEEE 802 3x Flow Control on all ports 802 1p Priority Tagging compatible on all ports 802 10 VLAN Tagging support on all ports 802 1D Bridges and STA 803 2z Gigabit Ethernet ports 803 2u Ethernet Fast Ethernet ports IETF MIB II RFC 1213 Bridge MIB for Spanning Tree RFC 1493 Bridge MIB for STP and CAM contents RFC 1314 ATM Management RFC 1695 RMON REC 1757 SMON RFC 2613 Avaya P332MF User s Guide 147 Appendix A Specifications e 140 000 hrs minimum see Section MTBF in Various Configurations Stacking Module Table A1 Stacking Module Number of RE Ports X330STK 2 Expansion Modules Gigabit Ethernet Expansion Modules Table A 2 Gigabit Ethernet Expansion Modules Name EES Interface Ports X33082 2
138. you should wait 30 seconds before disabling STP if you reset the switch enabled STP or inserted a new station The syntax for this command is set spantree enable disable Output Example P330 N set spantree enable bridge spanning tree enabled set spantree priority Usethe set spantree priority command to set the bridge priority for STP The syntax for this command is set spantree priority value value Number representing the priority of the bridge with a priority level from 0 to 65535 with 0 indicating high priority and 65535 indicating low priority Avaya P332MF User s Guide 115 Chapter 6 CLI Layer 2 Example To set the priority to 45000 P330 N4 set spantree priority 45000 Priority enabled set autopartition set license Usethe set autopartition command to enable or disable auto partitioning on specific switches of the stack Note This command can not be executed on the P332G ML and P332GT ML switches This command is used to set the autopartition status for the other P330 switches in the stack The syntax for this command is set autopartition enable disable module Output Example P330 N4 set autopartition enable 3 Auto partition is enabled in module 3 The set license command enables you to activate the SMON routing capability of the Avaya P330 stack An Avaya P330 stack can include several Avaya P330 switches One SMON routing license is required per Avaya P33

Avaya P332MF User's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents