Auto Page RF-425LCD Installation Manual
Contents
1. If your built in timer controls window sunroof closure in your car DO NOT change the timer setting This requires installer only programming Changing the value will adversely effect operation and may cause damage Note 2 Momentary output The momentary output selection will output a negative signal from the Channel 3 or 4 output immediately when the channel 3 or 4 button is pressed and will continue until the button is release Latched output The latched output selection will output a negative signal as soon as the Channel 2 3 amp 4 button is pressed and will continue until the button is pressed again Press Transmitter Button One Chirp LED one pulse Factory Default Setting Two Chirps LED two pulses Three Chirps LED three pulses Four Chirps LED four pulses 1 Channel 2 Output 2 sec Pulse Channel 2 Output Latched Channel 2 Output Timer control Pager Output 2 Channel 3 Output Momentary Channel 3 Output Latched Channel 3 Output Timer control Pager Output 3 Pink Wire 2 Step Unlock Pink Wire Factory Disarm 4 Channel 4 Output 2 sec Pulse Channel 4 Output Momentary Channel 4 Output Latched Channel 4 Output Timer control 12 960 Knox Street Unit B Torrance California 90502 Main Office 310 323 1800 Technical Support 800 262 2527 Ext 461 For Authorized Dealers Only www autopageusa com2. 1 RF 425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL FOR AUTHORIZED DEALERS ONLY THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY System Antenna No Connections Valet Override Switch Super Bright LED Status Indicator 87 87a 30 NORMALLY OPEN N O NORMALLY CLOSE N C COMMON The coil contacts 85 amp 86 are not needed as they are controlled within the main unit Standard Relay For Refference Orange Port 1 Dual Shock White Port 2 Optional Sensor BLUE CONNECTOR WHITE CONNECTOR 6 PIN 5 PIN WHITE DOME LIGHT OUTPUT RELAY REQUIRED GRAY 2ND CHANNEL OUTPUT WHITE BLUE 3RD CHANNEL OUTPUT 200mA 200mA PINK 2 STEP DOOR UNLOCK RELAY REQUIRED ORANGE STARTER INTERUPT OUTPUT RELAY REQUIRED GREEN NEGATIVE TRIGGER INPUT YELLOW IGNITION INPUT VIOLET POSITIVE TRIGGER INPUT BLUE TRUNK HOOD TRIGGER INPUT RF 425 R F 4 2 5 For Technical Assistance Call 800 945 2527 1 0 A BLUE BLACK HORN OUTPUT WHITE LIGHT FLASH BATTERY BROWN SIREN OUTPUT 1 5 A RED 12V MAIN POWER BLACK MAIN SYSTEM GROUND VIOLET UNLOCK N O 87 BROWN UNLOCK SWITCH N C 87a BLUE UNLOCK MOTOR COMMON 30 GREEN LOCK MOTOR COMMON 30 VIOLET RED LOCK N O 87 20A WHITE LOCK SWITCH N C 87a BLACK BLUE 4TH CHANNEL OUTPUT 200mA 10 PIN
3. 1 Way AM Transmitting Antenna WIRING HARNESS MAIN 5 PIN WIRE HARNESS 10 PIN MINI CONNECTOR WIRE HARNESS 6 PIN DOOR LOCK WIRE HARNESS 87 87a 30 NORMALLY OPEN N O NORMALLY CLOSE N C COMMON The coil contacts 85 amp 86 are not needed as they are controlled within the main unit Standard Relay For Refference VIOLET UNLOCK N O 87 BROWN UNLOCK SWITCH N C 87a BLUE UNLOCK MOTOR COMMON 30 GREEN LOCK MOTOR COMMON 30 VIOLET RED LOCK N O 87 20A WHITE LOCK SWITCH N C 87a 5 PIN 1 0 A BLUE BLACK HORN OUTPUT WHITE LIGHT FLASH BATTERY BROWN SIREN OUTPUT 1 5 A RED 12V MAIN POWER BLACK MAIN SYSTEM GROUND WHITE DOME LIGHT OUTPUT RELAY REQUIRED GRAY 2ND CHANNEL OUTPUT WHITE BLUE 3RD CHANNEL OUTPUT 200mA 200mA PINK 2 STEP DOOR UNLOCK RELAY REQUIRED ORANGE STARTER INTERUPT OUTPUT RELAY REQUIRED GREEN NEGATIVE TRIGGER INPUT YELLOW IGNITION INPUT VIOLET POSITIVE TRIGGER INPUT BLUE TRUNK HOOD TRIGGER INPUT BLACK BLUE 4TH CHANNEL OUTPUT 4 WIRING Keep wiring away from moving engine parts exhaust pipes and high tension cable Tape wires that pass through holes on the firewall to prevent fraying Be careful of sharp edges that may damage wires and causes short circuit CAUTION Do not connect the wire harness to the control module until all wiring
4. BLUE UNLOCK MOTOR COMMON 30 LT GREEN LOCK MOTOR COMMON 30 VIOLET RED LOCK N O 87 20A WHITE LOCK SWITCH N C 87a NOT USED NOT USED LOCK UN LOCK GROUND 8 5 WIRE REVERSE POLARITY ADDING ACTUATORS VIOLET UNLOCK N O 87 BROWN UNLOCK SWITCH N C 87a LT BLUE UNLOCK MOTOR COMMON 30 LT GREEN LOCK MOTOR COMMON 30 VIOLET RED LOCK N O 87 20A WHITE LOCK SWITCH N C 87a LOCK UN LOCK 12 VOLTS 20A 12v B LOCK UNLOCK LOCK UNLOCK GROUND LOCK LOCK UNLOCK UNLOCK FRONT DOORS BACK DOORS WHITE WIRE amp BROWN WIRE VIOLET WIRE amp VIOLET RED GREEN WIRE BLUE WIRE 9 VACCUM DOOR LOCK SYSTEM PROGRAMMING A TRANSMITTER PROGRAMMING Enter 1 Turn the Ignition switch OFF ON 3 TIMES and stay in ON position Within 15 seconds 2 Push the Valet switch 2 times and hold in on the 2nd push when a long chirp is heard then release the valet switch You are now in the Transmitter programming mode Program 1 Press any button on transmitter 1 until the siren responds with a confirming chirp the first transmitter is now programmed 2 Press any button on the second transmitter until the siren responds with a confirming chirp the second transmitter is now programmed 3 Apply the same procedure to program 3rd and 4th Exit Turn Ignition to OFF position or leave it for 15 seconds 3 long chirps and 3 Parking
5. Light will confirm exit Note If more than 4 transmitters programmed the system will only keep the last four LOCK UN LOCK BROWN FROM DOOR BROWN WIRE BLUE WIRE VIOLET WIRE 12v B WHITE WIRE GREEN WIRE GREEN WIRE TO PUMP VIOLET RED WIRE GROUND 405 6 PIN CONNECTOR LOCK PUMP 10 ALARM FEATURE A PRORAMMING 1 Turn the Ignition switch ON OFF 3 TIMES and stay in OFF position 2 Push the Valet switch 3 times and hold in on the 3rd push when a long chirp is heard then release the valet switch You are now in the Alarm feature A programming mode 3 Press the transmitter button corresponding to the feature you want to program a The factory default settings is always 1 LED flash 1 chirp 4 Depress the transmitter button again to change the feature Simply keep pressing the transmitter button again until the module advances to your desired setting Press Transmitter Button One Chirp LED one pulse Factory Default Setting Two Chirps LED two pulses Three Chirps LED three pulses Four Chirps LED four pulses 1 Siren Confirmation chirp on only All Confirmation chirps On Horn Confirmation chirp on only All Confirmation chirps off 2 Automatic Rearm off Automatic Rearm on 3 Instant Door Ajar error chirp 45 seconds delay Door Ajar error chirp Exit Turn Ignition to OFF position or leave it for 15 seconds 3 long chirps and 3 Parki
6. and keep it away from large metal objects or chassis for best reception 4 PIN BLACK CONNECTOR AM TRANSMITTING ANTENNA MODULE The transmitting antenna mounting location should be the upper left or lower left corner of driver s windshield For optimum range we suggest that the antenna be mounted as shown in picture to the right Antenna tip facing up Warning Do not mount in such a manner that it obstructs the driver s view Paging button used to page person in possession of the 2 Way transmitter Remove the protective tape backing Carefully align the two way transceiver antenna and apply to windshield Route the black connector wire behind the trim and connect to the two way transceiver antenna Connect the other end to the control module Special considerations must be made for windshield glass as some newer vehicles utilize a metal shielded window glass that will inhibit or restrict RF reception In these vehicles route the two ways transceiver antenna module away from metallic shielded window glass as far as possible 7 VIOLET UNLOCK N O 87 BROWN UNLOCK SWITCH N C 87a LT BLUE UNLOCK MOTOR COMMON 30 LT GREEN LOCK MOTOR COMMON 30 VIOLET RED LOCK N O 87 20A WHITE LOCK SWITCH N C 87a LOCK UN LOCK NOT USED NOT USED 12 VOLTS 6 PIN DOOR LOCK CONNECTOR 3 WIRE NEGATIVE 3 WIRE POSITIVE VIOLET UNLOCK N O 87 BROWN UNLOCK SWITCH N C 87a LT
7. ay I E Pager interface 9 GRAY WIRE 200mA PROGRAMMABLE OUTPUT CHANNEL 2 OUTPUT Factory default setting This will become a 2 seconds pulse ground by activate channel 2 on transmitter for two seconds the current capacity of this wire is 200 mA This feature allows you to remote control trunk release or other electric device This output can also be programmed to provide the following type of output 2 sec pulse latched timer control and pager See Alarm Feature C 1 Programming PAGER OUTPUT See Feature C 1 Programming This wire provides a negative output when the alarm triggered The current capacity of this wire is 200mA For optional electrical device in this system please connected to an additional relay I E Pager interface 10 WHITE WIRE 200mA DOME LIGHT CONTROL OUTPUT This wire becomes grounded when the dome light controls circuit active The current capacity of this wire is 200mA This wire can control the operation of the interior lights An optional 10 Amps relay can be used to this system for interior lights operation a Upon disarming the interior lights will remain on for 30 seconds b If the vehicle is v iolated the interior light will flash for the same duration as the siren RF ANTENNA BLACK THIN WIRE The black thin wire on the control module is the receiver antenna wire Antenna placement is very important Ensure that it is unwrapped and stretched out with the last 6 straight
8. ay in OFF position 2 Push the Valet switch 7 times and hold in on the 7th push when a long chirp is heard then release the valet switch You are now in the Alarm feature C programming mode 3 Press the transmitter button corresponding to the feature you want to program Exit Turn Ignition to OFF position or leave it for 15 seconds 3 long chirps and 3 Parking Light will confirm exit Channel 2 3 4 Timer Control Output Programming Enter 1 Turn the Ignition switch ON OFF 3 TIMES and stay in OFF position 2 Push the Valet switch 7 times and hold in on the 7th push when a long chirp is heard then release the valet switch You are now in the Alarm feature C programming mode Timer Program Channel 2 3 4 1 a CH2 Press and release the transmitter button 3 times 3 LED flash 3 siren horn chirp to indicate you are in features Channel 2 Timer Programming mode 1 b CH3 Press and release the transmitter button 3 times 3 LED flash 3 siren horn chirp to indicate you are in features Channel 3 Timer Programming mode 1 c CH4 Press and release the transmitter button 4 times 4 LED flash 4 siren horn chirp to indicate you are in features Channel 4 Timer Programming mode 2 Press and hold the valet switch the timer will immediately start 3 When the desired interval has passed release the valet switch 1 long chirp for confirmation Set to any interval between 1 second and 2 minutes Note 1
9. d to a Ignition switched 12 volts source This wire should receive 12 Volts when the ignition key is in the ON and START position When the ignition is turned OFF this wire should receive 0 voltage 5 GREEN WIRE NEGATIVE DOOR SWITCH SENSING INPUT This wire is the ground trigger input wire for negative door pin switch This wire connection is for grounding a factory type door pin switch locate the common wire for all door pin switches and make the connection of the Green Wire 6 ORANGE WIRE 500mA GROUNDED OUTPUT WHEN ARMED This wire will become grounded when the alarm is armed The current capacity of this wire is 500mA This output can control starter disable when an intrusion is detected and the system is triggered The alarm will prevent any unauthorized persons from starting the vehicle NOTE If more than one electronic device will be connected to the H10 6 ORANGE Wire it will be necessary to isolate the connection of each device control wires with a 1N4003 diode 7 PINK WIRE 2 STEPS UNLOCK OUTPUT FACTORY DISARM See Feature C 3 Programming The 2 steps unlock feature will work for the most fully electronic door lock circuit The vehicle must have an electronic door lock switch which locks and unlocks all of vehicle s doors When wired for this feature press the button one time the alarm will disarm and unlock the driver s door only If you press the button two times within 3 seconds the ala
10. e Wire Zone 4 Ground Trigger 2 Black Wire Negative 1 Red Wire 12Volts Function For both Orange Port 1 and White Port 2 Allows easy positive negative instant trigger and warn away trigger connection with quick disconnect ability for other detection devices 5 10 PIN MINI CONNECTOR WIRE HARNESS 1 BLUE WIRE GROUND INSTANT TRIGGER INPUT This wire is the ground trigger input wire for hood trunk pin switches 2 Black BLUE WIRE 200mA Timer Control Channel 4 Output This wire has a built in user programmable timer output that provides a ground through this wire Press the transmitter and button at the same time You may program the built in timer to send a ground signal for any time interval between 1 second and 2 minutes For instance this timer output may be used to turn on the headlight with the remote control Also on certain BMW Mercedes Benz Jaguar and Volkswagen cars you can use this unique timed output to allow remote closure of all power window and sunroof without the need for an external module See Feature C 4 Programming 3 VIOLET WIRE POSITIVE DOOR SWITCH SENSING INPUT This wire is the positive trigger input wire for positive door pin switch This wire connection is for positive type factory door pins typical FORD MOTOR Locate the common wire for all door pin switches and make the connection of the Violet Wire 4 YELLOW WIRE TO IGNITION SWITCHED 12V This wire is connecte
11. ng Light will confirm exit ALARM FEATURE B PRORAMMING 1 Turn the Ignition switch ON OFF 3 TIMES and stay in OFF position 2 Push the Valet switch 5 times and hold in on the 5th push when a long chirp is heard then release the valet switch You are now in the Alarm feature B programming mode 3 Press the transmitter button corresponding to the feature you want to program Exit Turn Ignition to OFF position or leave it for 15 seconds 3 long chirps and 3 Parking Light will confirm exit Press Transmitter Button One Chirp LED one pulse Factory Default Setting Two Chirps LED two pulses Three Chirps LED three pulses Four Chirps LED four pulses 1 0 8 second Door lock pulses 3 5 second Door lock pulse Double pulse unlock Door lock with Comfort Feature 2 Active arming Passive arming without passive door locking Passive arming with passive door locking 3 Ignition controlled door locks amp unlocks Ignition controlled door locks only Ignition controlled door unlocks only Without ignition controlled door locks amp unlocks 4 Pathway illumination feature off Parking light turns on for 30 second upon an unlock signal Parking light turns on for 30 second upon an unlock signal amp 10 second upon a lock signal 11 ALARM FEATURE C PRORAMMING 1 Turn the Ignition switch ON OFF 3 TIMES and st
12. rm will disarm and unlock all doors FACTORY SECURITY DISARM SIGNAL OUTPUT This wire is designed to disarm a factory installed security system This wire sends a negative 1 seconds pulse upon a remote door unlocking This makes integration of this system into a vehicle with a factory alarm very simple lt Starter Wire key side gt lt Yellow gt lt 12V Ignition gt lt Red gt Orange Starter Disable Wire lt Starter Wire motor side gt STARTER 87 87a 30 86 85 lt White Wire gt lt Purple gt RK 1 6 8 WHITE BLUE WIRE PROGRAMMABLE OUTPUT CHANNEL 3 OUTPUT Factory default setting This wire is built in user programmable timer output provides a ground through this wire Press the button on the transmitter You may program the built in timer to send a ground signal for any time interval between 1 second and 2 minutes For instance this timer output may be used to turn on the headlight with the remote control Also on certain BMW Mercedes Benz Jaguar and Volkswagen cars you can use this unique timed output to allow remote closure of all power window and sunroof without the need for an external module See Alarm Feature C 2 Programming PAGER OUTPUT See Feature C 2 Programming This wire provides a negative output when the alarm triggered The current capacity of this wire is 200mA For optional electrical device in this system please connected to an additional rel
13. to vehicle is complete MAIN 5 PIN WIRE HARNESS WHITE WIRE PARKING LIGHT RELAY OUTPUT 12 V 10A OUTPUT Connect the WHITE wire to the parking light wire coming from the headlight switch Do not connect the WHITE wire to the dashboard lighting dimmer switch Damage to the dimmer will result The limitation of the WHITE wire is 10 AMP max Do not exceed this limit or damage to the alarm and parking relay will result BLACK WIRE SYSTEM GROUND This is main ground connection of the alarm module Make this connection to a solid section of the vehicle frame Do not connect this wire to any existing ground wires supplied by the factory wire loom make the connection to the vehicle s frame directly BROWN WIRE SIREN OUTPUT This is the positive output connection for the siren Current capacity is 2 amps Make connection to the red wire from the siren Make the black wire coming from the siren to a good chassis ground RED WIRE SYSTEM POWER 12V CONSTANT The RED wire supplies power to the system Connect this wire to a constant 12 volt source BLUE BLACK WIRE HORN OUTPUT This wire is provided to use the existing vehicle s horn as the alarm system s optional warning audible device It s a transistorized low current output and should only be connected to the low current positive output from the vehicle s horn switch 4 PIN ORANGE CONNECTOR FOR 2 STAGE SHOCK SENSOR 4 Green Wire Warn Away Input 3 Blu
Download Pdf Manuals
Related Search