Home

ASUS P8H61 Owner's Manual

1. 7 C Co Coma Ea P8H61 Series 240 pin DDR3 DIMM sockets Chapter 1 Product introduction 1 13 1 7 2 Memory configurations You may install 512MB 1GB 2GB and 4GB unbuffered non ECC DDR3 DIMMs into the DIMM sockets N You may install varying memory sizes in Channel A and Channel B The system maps the total size of the lower sized channel for the dual channel configuration Any excess memory from the higher sized channel is then mapped for single channel operation According to Intel CPU specification DIMM voltage below 1 65V is recommended to protect the CPU Always install DIMMs with the same CAS latency For optimum compatibility we recommend that you obtain memory modules from the same vendor Due to the memory address limitation on 32 bit Windows OS when you install 4GB or more memory on the motherboard the actual usable memory for the OS can be about 3GB or less For effective use of memory we recommend that you do any of the following Use a maximum of 3GB system memory if you are using a 32 bit Windows OS Install a 64 bit Windows OS when you want to install 4GB or more on the motherboard This motherboard does not support DIMMs made up of 512Mb 64MB chips or less The maximum 16GB memory capacity can be supported with 8GB or above DIMMs ASUS will update the memory QVL once the DIMMs are available in the market
2. 1 19 UNTO E 1 20 Bel TC 1 21 1 10 1 Rear panel connectors 1 21 1 10 2 Internal connectors T 1 22 Contents 1 11 SO IIWare SUNN 1 27 1 11 1 Installing an operating system 1 27 1 11 2 Support DVD information 1 27 Chapter 2 BIOS information 2 1 2 2 2 3 2 4 2 5 Managing and updating your BIOS 2 1 2 1 1 ASUS Update utility 2 1 212 ASUS EZ Hash EE 2 2 2 1 8 ASUS CrashFree BIOS 3 utility 2 3 2 1 4 ASUS BIOS Updater 2 4 BIOS setup Program sam arsen 2 7 Malm EE EN 2 11 2 3 1 System Language 2 11 2 3 2 System Date sreronrernnronnnnvenrnvrnnnrvrnnnvennnnvrnrnvnnnnvernnnnen 2 11 233 System TUNG _ u u u u uu u uuu uu uu uu 2 11 EE OCUN EEE 2 11 Ai Tweaker menu 2 13 2 4 1 Ai Overclock Tune 2 13 2 4 2 Memory Frequencoy 2 14 2 4 3 EPU Power Saving Mode 2 14 244 En 2 14 2 4 5 DRAM Timing Control 2 14 2 4 6 CPU Power Managem
3. Front Panel Type HD Allows you to set the front panel audio connector AAFP mode to legacy AC 97 or high definition audio depending on the audio standard that the front panel audio module supports HD Sets the front panel audio connector AAFP mode to high definition audio AC97 Sets the front panel audio connector AAFP mode to legacy AC 97 Realtek LAN Controller Enabled Enabled Enables the Realtek LAN controller Disabled Disables the controller Realtek PXE OPROM Disabled This item appears only when you set the previous item to Enabled and allows you to enable or disable the PXE OptionRom of the Realtek LAN controller Configuration options Enabled Disabled Serial Port Configuration The sub items in this menu allow you to set the serial port configuration Serial Port Enabled Allows you to enable or disable the serial port COM Configuration options Enabled Disabled ASUS P8H61 Series Change Settings IO 3F8h IRQ 4 Allows you to select the Serial Port base address Configuration options IO 3F8h IRQ 4 lO 2F8h IRQ 3 IO 3E8h IRQ 4 I0 2E8h IRQ 3 Parallel Port Configuration The sub items in this menu allow you to set the parallel port configuration Parallel Port Enabled Allows you to enable or disable the parallel port LPT LPTE Configuration options Enabled Disabled Change Settings IO 3F8h IRQ 4 Allows you to select an optimal setting for Super I O devices Conf
4. Connect the CPU fan cable to the connector on the motherboard labeled CPU_FAN CPU_FAN GND CPU FAN PWM CPU FAN IN CPU FAN PWR P8H61 Series CPU fan connector Do not forget to connect the CPU fan connector Hardware monitoring errors can occur if 1 6 3 you fail to plug this connector Uninstalling the CPU heatsink and fan To uninstall the CPU heatsink and fan 1 2 3 Disconnect the CPU fan cable from the connector on the motherboard Rotate each fastener counterclockwise Pull up two fasteners at a time in a diagonal sequence to disengage the heatsink and fan assembly from the motherboard ASUS P8H61 Series 4 Carefully remove the heatsink and fan assembly from the motherboard 5 Rotate each fastener clockwise to ensure correct orientation when reinstalling 1 7 System memory 1 7 1 Overview The motherboard comes with two Double Data Rate 3 DDR3 Dual Inline Memory Modules DIMM sockets A DDR3 module has the same physical dimensions as a DDR2 DIMM but is notched differently to prevent installation on a DDR2 DIMM socket DDR3 modules are developed for better performance with less power consumption The figure illustrates the location of the DDR3 DIMM sockets DIMM_B1 lt 2 a Channel Sockets Channel A DIMM_A1 Channel B DIMM Bi
5. 1 1 1 3 2 Innovative ASUS features 1 2 Before YOU proceed 1 5 Motherboard overview u 1 6 1 5 1 Placement direction 1 6 152 SAM NE aa 1 6 1 5 3 Motherboard layoul 1 7 154 Layout contents 1 7 Central Processing Unit CPU 1 8 1 6 1 Installing the CPU 1 8 1 6 2 Installing the CPU heatsink and fan 1 11 1 6 3 Uninstalling the CPU heatsink and fan 1 12 VSEM MEMNON save 1 13 1 7 1 OE ER 1 13 1 7 2 Memory configurations 1 14 1 3 Installing a DIMM 1 18 1 7 4 Removing a DIMM sseeeneseessrreerrsrrrsernsrrrsrrrsrrrsresee 1 18 EXPANSION E sirinin aeea aaee 1 19 1 8 1 Installing an expansion card 1 19 1 8 2 Configuring an expansion card 1 19 CS9 CI GIONS u u EE 2 an asss ss 1 19 1 8 4 PCI Express WE 1 19 1 85 PCI Express x16 slot
6. 1 24 Front panel audio connector 10 1 pin AAFP 1 7 1 8 1 6 Central Processing Unit CPU The motherboard comes with a surface mount LGA1155 socket designed for the Intel Second Generation Core i7 Core i5 Core i3 processors N Unplug all power cables before installing the CPU e Upon purchase of the motherboard ensure that the PnP cap is on the socket and the socket contacts are not bent Contact your retailer immediately if the PnP cap is missing or if you see any damage to the PnP cap socket contacts motherboard components ASUS will shoulder the cost of repair only if the damage is shipment transit related Keep the cap after installing the motherboard ASUS will process Return Merchandise Authorization RMA requests only if the motherboard comes with the cap on the LGA1155 socket The product warranty does not cover damage to the socket contacts resulting from incorrect CPU installation removal or misplacement loss incorrect removal of the PnP cap 1 6 1 Installing the CPU To install a CPU 1 Locate the CPU socket on the motherboard All ONA DCH O ome A P8H61 Series CPU socket LGA1155 2 Press the load lever with your thumb A Land lever and then move it to the right B until it is released from the retention tab A To prevent d
7. 2 2 Z The ASUS Update utility is capable of updating itself through the Internet Always update the utility to avail all its features Updating from a BIOS file a Select Update BIOS from file then click Next b Locate the BIOS file from the Open window then click Open 3 Follow the onscreen instructions to complete the updating process 2 1 2 ASUS EZ Flash 2 The ASUS EZ Flash 2 feature allows you to update the BIOS without using an OS based utility Before you start using this utility download the latest BIOS file from the ASUS website at www asus com eng To update the BIOS using EZ Flash 2 1 Insert the USB flash disk that contains the latest BIOS file to the USB port 2 Enter the Advanced Mode of the BIOS setup program Go to the Tool menu to select ASUS EZ Flash Utility and press lt Enter gt to enable it ASUSTek EZ Flash 2 BIOS ROM Utility VOO 75 il Flash Info MODEL P8H61 VER 0210 DATE 01 04 2011 File Path fsO Drive Folder Info LEON 01 01 11 10 23p 4194304 P8H61 ROM gd File Info MODEL Help Info Enter Select or Load Tab Switch Up Down PageUp PageDown Home End Move Esc Exit F2 Backup ASUS P8H61 Series 3 Press lt Tab gt to switch to the Drive field 4 Press the Up Down arrow keys to find the USB flash disk that contains the latest BIOS and then press lt Enter gt 5 Press lt Tab gt to switch to the Folder Info field 6 Press the Up Down arrow keys to
8. The default memory operation frequency is dependent on its Serial Presence Detect SPD which is the standard way of accessing information from a memory module Under the default state some memory modules for overclocking may operate at a lower frequency than the vendor marked value To operate at the vendor marked or at a higher frequency refer to section 2 4 Ai Tweaker menu for manual memory frequency adjustment For system stability use a more efficient memory cooling system to support a full memory load 2 DIMMs or overclocking condition ASUS P8H61 Series P8H61 Series Motherboard Qualified Vendors Lists QVL DDR3 1333 MHz capability Vendors Part No AD31333001GOU AD31333G001GOU AD31333002GOU AD31333G002GMU 78 A1GC6 9L1 78 A1GC6 9L1 CM3X1024 1333C9DHX CM3X1024 1333C9 TR3X3G1333C9 G TR3X3G1333C9 G CM3X1024 1333C9DHX CMD24GX3M6A1333C9 XMP CMX8GX3M4A1333C9 CT12864BA1339 8FF CT25664BA1339 16FF BL25664BN1337 16FF XMP EBJ10UE8EDFO DJ F EBJ21UE8EDFO DJ F F3 10600CL8D 2GBHK XMP F3 10666CL7T 3GBPK XMP F3 10666CL9T 3GBNQ F3 10600CL8D 4GBHK XMP F3 10666CL8D 4GBECO XMP F3 10666CL7T 6GBPK XMP F3 10666CL7D 8GBRH XMP F3 10666CL9D 8GBRL GET316GB1333C9QC GV32GB1333C9DC GG34GB1333C9DC GV34GB1333C9DC HMT112U6TFR8A H9 HMT325U6BFR8C H9 HMT125U6TFR8A H9 HMT351U6BFR8C H9 FLFD45F B8KL9 NAES FLFE85F C8KF9 CAES FLFE85F C8KM9 NAES FLFE85F B8KL9 NEES FLFF65F C8KM9 NEES KVR1333D3N9 1G KVR1333D3N9 2G KVR1333
9. 24 9 9 9 24 9 9 S 1 65V 1 35V low voltage 1 35V low voltage 7 7 7 18 1 5 1 6V 9 9 9 24 1 5 1 6V 8 8 8 21 1 5 1 6V 8 8 8 24 XMP 1 35V 7 7 7 18 1 5 1 6V 7 7 7 21 1 5V 9 9 9 24 1 5V 9 9 9 24 1 5V 9 9 9 24 1 5V en 27 9 9 9 24 1 5V 1 35V low voltage 1 35V low voltage KFCSFNMXF BXX 15A KKB8FNWBFGNX 26A KFC8FNMXF BXX 15A J1108BDBG DJ F H5TQ2G83AFRH9C J1108BDBG DJ F D1288JPNDPLD9U J1108BDSE DJ F H5TQ2G83AFRH9C H5TQ2G83AFR D9LGQ 9FF22D9KPT D9LGK 9KF27D9KPT D9LGK continued on the next page 1 5V 1 5V 1 5V 1 5V 1 65V XMP 1 25V 1 5V OO N IcO cO cO cO oO 9 9 9 20 1 65V 9 9 9 20 1 7V 9 9 9 20 1 7V DDR3 1333 MHz capability DIMM socket Vendors Part No i i Timing Voltage support Optional 1 DIMM 2 DIMMs 9 9 9 20 1 65V 7 7 7 20 1 65V 7 7 7 20 1 75V 9 9 9 20 1 65V 3 x 2GB 7 7 7 20 1 65V OCZ3X1333LV6GK XMP 6GB 3 x 2GB DS 8 8 8 20 1 60V OCZ3G1333LV8GK 8GB 2x 4GB DS 9 9 9 20 1 65V OCZ3RPR1333C9LV8GK 8GB 2x 4GB DS 9 9 9 20 1 65V AL7F8G73D DG1 1GB SS PSC A3P1GF3DGF 8 8 8 24 1 5V AL7F8G73F DJ2 1GB SS PSC A3P1GF3FGF AL8F8G73D DG1 2GB DS PSC A3P1GF3DGF 8 8 8 24 1 5V AL8F8G73F DJ2 2GB DS PSC A3P1GF3FGF AMSUNG M378B2873FHS CH9 1GB SS Samsung K4B1G0846F AMSUNG M378B5673FHO CH9 2GB DS Samsung K4B1G0846F AMSUNG M378B5273CH0 CH9 4GB DS Samsung K4B2G0846C uper Talent W1333UA1GH 1GB SS HYNIX H5TQ1G83TFR uper Talent W1333UB2GS 2GB DS Samsung K4B1G0846F uper Talen
10. 6 Anti Surge Suppolt 2 25 Bet TE EE EE ER 2 26 2 7 1 Bootup NumLock State 2 26 272 Full Screen Logo 2 26 2 7 3 Option ROM Messages 2 26 274 SUP I uu uuu uu Meee ee are eee 2 26 2 7 5 Boot Option Priorities 2 27 276 BOO OVE tte eebe 2 27 19019 MEDU Hr 2 28 2 8 1 ASUS EZ Flash Utility 2 28 2 8 2 ASUS SPD Information 2 28 2 8 3 ASUS OC Profile 2 28 DE NE EEE 2 29 vi Notices Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions This device may not cause harmful interference and This device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with manufacturer s i
11. BIOS in the future Copy the original motherboard BIOS using the ASUS Update utility 2 1 1 ASUS Update utility The ASUS Update is a utility that allows you to manage save and update the motherboard BIOS in Windows environment e ASUS Update requires an Internet connection either through a network or an Internet Service Provider ISP This utility is available in the support DVD that comes with the motherboard package Installing ASUS Update To install ASUS Update 1 Place the support DVD in the optical drive The Drivers menu appears 2 Click the Utilities tab then click Al Suite Il 3 Follow the onscreen instructions to complete the installation V Quit all Windows applications before you update the BIOS using this utility Updating the BIOS To update the BIOS 1 From the Windows desktop click Start gt Programs gt ASUS gt Al Suite Il gt Al Suite II X XX XX to launch the Al Suite II utility The Al Suite II Quick Bar appears 2 Click Update button from the Quick Bar and then click ASUS Update from the popup menu The ASUS Update main screen appears From the list select either of the following methods Updating from the Internet a Select Update BIOS from the Internet then click Next b Select the ASUS FTP site nearest you to avoid network traffic then click Next c Fromthe FTP site select the BIOS version that you wish to download then click Next Chapter 2 BIOS information 2 1
12. Failure to do so can cause severe damage to both the motherboard and the components 1 Press the retaining clips outward to DIMM notch unlock a DIMM socket 2 Align a DIMM on the socket such that the notch on the DIMM matches the DIMM slot key on the socket Unlocked retaining clip DIMM SI t key Ki A DIMM is keyed with a notch so that it fits in only one direction DO NOT force a DIMM into a socket in the wrong direction to avoid damaging the DIMM 3 Firmly insert the DIMM into the socket until the retaining clips snap back in place and the DIMM is properly seated Locked Retaining Clip 1 7 4 Removing a DIMM To remove a DIMM 1 Simultaneously press the retaining clips outward to unlock the DIMM Z Support the DIMM lightly with your fingers when pressing the retaining clips The DIMM might get damaged when it flips out with extra force 2 Remove the DIMM from the socket ASUS P8H61 Series 1 8 Expansion slots In the future you may need to install expansion cards The following sub sections describe the slots and the expansion cards that they support 4 Unplug the power cord before adding or removing expansion cards Failure to do so may cause you physical injury and damage motherboard components 1 8 1 Installing an expansion card To install an expansion card 1 Before installing the expansion card read the documentation that came with it and make the necessary hardware settings for the
13. Line Out Front Speaker Out Front Speaker Out Front Speaker Out Pink Rear panel Mic In Mic In Bass Center Bass Center Lime Front panel _ _ _ Side Speaker Out To configure an 8 channel audio output Use a chassis with HD audio module in the front panel to support 8 channel audio output Chapter 1 Product introduction 1 21 1 22 7 USB 2 0 ports 1 and 2 These two 4 pin Universal Serial Bus USB ports are for USB 2 0 1 1 devices 8 USB 2 0 ports 3 and 4 These two 4 pin Universal Serial Bus USB ports are for USB 2 0 1 1 devices 9 Serial port This 9 pin COM1 port is for pointing devices or other serial devices 10 PS 2 Keyboard port purple This port is for a 1 10 2 Internal connectors 1 Front panel audio connector 10 1 pin AAFP PS 2 keyboard This connector is for a chassis mounted front panel audio I O module that supports either HD Audio or legacy AC 97 audio standard Connect one end of the front panel audio I O module cable to this connector AAFP SENSE2_RETUR m m PORT2 L NC far Line out L o m SENSE SEND o m NC SENSE1_RETUR Ja st PORT2 R NC Je gl Line out R PRESENCE slk PORT1 R NC Ja sit MICPWR GND PORT1 L AGND Ja gl MIC2 PIN 1 PIN 1 HD audio compliant Legacy AC 97 ss pin definition compliant definition W P8H61 Series Front panel audio con
14. Select Yes to load the default values Save Changes amp Reset Once you are finished making your selections choose this option from the Exit menu to ensure the values you selected are saved When you select this option or if you press lt F10 gt a confirmation window appears Select Yes to save changes and exit Discard Changes amp Exit This option allows you to exit the Setup program without saving your changes When you select this option or if you press lt Esc gt a confirmation window appears Select Yes to discard changes and exit ASUS EZ Mode This option allows you to enter the EZ Mode screen Launch EFI Shell from filesystem device This option allows you to attempt to launch the EFI Shell application shellx64 efi from one of the available devices that have a filesystem Chapter 2 BIOS information 2 29 2 30 ASUS P8H61 Series ASUS contact information ASUSTeK COMPUTER INC Address Telephone Fax E mail Web site Technical Support Telephone Online support 15 Li Te Road Peitou Taipei Taiwan 11259 886 2 2894 3447 886 2 2890 7798 info asus com tw www asus com tw 86 21 38429911 support asus com ASUS COMPUTER INTERNATIONAL America Address Telephone Fax Web site Technical Support Telephone Support fax Online support 800 Corporate Way Fremont CA 94539 USA 1 510 739 3777 1 510 608 4555 usa asus com 1 812 282 2787 1 812 284 0883 support asus com ASUS COMPUTER Gmb
15. quality Conductive Polymer Capacitors P8H61 PLUS only continued on the next page P8H61 Series specifications summary ASUS exclusive Precision Tweaker overclocking features vCore Adjustable CPU voltage at 0 01V increment VCCIO Adjustable I O voltage at 0 005V increment vDRAM Bus 190 step Memory voltage control VPCH 190 step Chipset voltage control SFS Stepless Frequency Selection BCLK PEG frequency tuning from 80MHz up to 300MHz at 1MHz increment Overclocking protection ASUS C P R CPU Parameter Recall Rear panel ports 1 x PS 2 Mouse port green 1 x PS 2 Keyboard port purple 1 x COM port 1 x LPT port 1 x LAN RJ 45 port 4 x USB 2 0 1 1 ports 3 x Audio jacks ene iyan y 3 x USB 2 0 1 1 connectors support additional 6 USB 2 0 1 1 switches buttons ports 4 x SATA 3 0 Gb s connectors 1 x CPU fan connector 1 x Chassis fan connector 1 x Front panel audio connector 1 x S PDIF Out connector 1 x System panel connector 1 x Internal speaker connector 1 x 24 pin EATX power connector 1 x 4 pin ATX 12V power connector BIOS features 32 Mb Flash ROM EFI BIOS PnP DMI v2 0 WfM 2 0 ACPI v2 0a SM BIOS v2 6 Multi language BIOS Accessories 2 x Serial ATA 3 0Gb s cables 1 x I O shield 1 x User Manual 1 x Support DVD Support DVD Drivers ASUS utilities ASUS Update Anti virus software OEM version Form factor ATX form factor 12 in x 8 in 30 5 cm x 20 3 cm Specifications are subjec
16. shut down or reset the system while updating the BIOS Doing so can cause system boot failure Chapter 2 BIOS information 2 3 2 4 2 1 4 ASUS BIOS Updater The ASUS BIOS Updater allows you to update BIOS in DOS environment This utility also allows you to copy the current BIOS file that you can use as a backup when the BIOS fails or gets corrupted during the updating process The succeeding utility screens are for reference only The actual utility screen displays may not be same as shown Before updating BIOS 1 Prepare the motherboard support DVD and a USB flash drive in FAT32 16 format and single partition 2 Download the latest BIOS file and BIOS Updater from the ASUS website at http support asus com and save them on the USB flash drive N NTFS is not supported under DOS environment Do not save the BIOS file and BIOS Updater to a hard disk drive or USB flash drive in NTFS format 3 Turn off the computer and disconnect all SATA hard disk drives optional Booting the system in DOS environment 1 Insert the USB flash drive with the latest BIOS file and BIOS Updater to the USB port 2 Boot your computer When the ASUS Logo appears press lt F8 gt to show the BIOS Boot Device Select Menu Insert the support DVD into the optical drive and select the optical drive as the boot device Please select boot device SATA XXXXXXXXXXXXXXXX USB XXXXXXXXXXXXXXXXX UEFI XXXXXXXXXXXXXXXX Enter Setup T and
17. with the configuration options for that item Scroll bar A scroll bar appears on the right side of a menu screen when there are items that do not fit on the screen Press the Up Down arrow keys or lt Page Up gt lt Page Down keys to display the other items on the screen Navigation keys At the bottom right corner of the menu screen are the navigation keys for the BIOS setup program Use the navigation keys to select items in the menu and change the settings General help At the top right corner of the menu screen is a brief description of the selected item Configuration fields These fields show the values for the menu items If an item is user configurable you can change the value of the field opposite the item You cannot select an item that is not user configurable A configurable field is highlighted when selected To change the value of a field select it and press lt Enter gt to display a list of options ASUS P8H61 Series 2 3 Main menu The Main menu screen appears when you enter the Advanced Mode of the BIOS Setup program The Main menu provides you an overview of the basic system information and allows you to set the system date time language and security settings Ai Tweaker Advanced Monitor Choose the system default language System Language English System Date Mon 09 13 2010 System Time 16 46 15 gt Security 2 3 1 System Language English Allows you to choose the BIOS language version fr
18. 0 The Intel Turbo Boost technology 2 0 support depends on the CPU types Refer to www asus com for Intel CPU support list Chipset Memory 2 X DIMMs max 16GB DDR3 1333 1066 MHz non ECC un buffered memory Dual channel memory architecture Supports Intel Extreme Memory Profile XMP The maximum 16GB memory capacity can be supported with 8GB or above DIMMs ASUS will update the memory QVL once the DIMMs are available in the market Refer to www asus com for the latest Memory QVL Qualified Vendors List When you install a total memory of 4GB capacity or more Windows 32 bit operating system may only recognize less than 3GB We recommend a maximum of 3GB system memory if you are using a Windows 32 bit operating system Expansion slots 1 x PCI Express 2 0 x16 slot 2 x PCI Express 2 0 x1 slots 3 x PCI slots Storage Intel H61 Express Chipset 4x Serial ATA 3 0 Gb s connectors LAN Realtek 8111E Gigabit LAN controller Audio Realtek ALC887 8 channel High Definition Audio CODEC Use a chassis with HD audio module in the front panel to support an 8 channel audio output USB 10 x USB 2 0 1 1 ports 6 ports at the mid board 4 ports at the back panel ASUS unique ASUS Anti Surge Protection features ASUS EPU ASUS TurboV ASUS Auto Tuning ASUS Fan Xpert ASUS EFI BIOS ASUS Al Suite II ASUS Al Charger ASUS CrashFree BIOS 3 ASUS EZ Flash 2 ASUS MyLogo 2 Other features 100 All High
19. 005V interval q The values of the CPU Offset Voltage DRAM Voltage VCCIO Voltage CPU PLL Voltage and PCH Voltage items are labeled in different color indicating the risk levels of high voltage settings The system may need better cooling system to work stably under high voltage settings 2 4 12 Load Line Calibration Auto Load line is defined by Intel VRM specification and affects CPU voltage The CPU working voltage will decrease proportionally to CPU loading Higher load line calibration would get higher voltage and better overclocking performance but increase the CPU and VRM thermal This item allows you to set this function for better system performance Configuration options Auto Disabled Enabled Z The actual performance boost may vary depending on your CPU specification 2 4 13 Auto PSI Enabled Allows you to enable or disable the Auto PSI function Configuration options Disabled Enabled 2 4 14 CPU Spread Spectrum Auto Auto Automatic configuration Disabled Enhances the BCLK overclocking ability Enabled Sets to Enabled for EMI control ASUS P8H61 Series 2 5 Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices WM Be cautious when changing the settings of the Advanced menu items Incorrect field values H can cause the system to malfunction Ai Tweaker Advanced Monitor Boot CPU Configuration Paramete
20. 1 1 DDR3 1333 Support KD bss PCle 2 0 loi P ymer apacitors 18 1 3 2 Intel H61 Express Chipset The Intel H61 Express Chipset is the latest single chipset design to support the new 1155 socket Intel Core i7 Core i5 Core i3 second generation processors It provides improved performance by utilizing serial point to point links which allows increased bandwidth and stability Dual Channel DDR3 1333 1066MHz support The motherboard supports DDR3 memory that features data transfer rates of 1333 1066 MHz to meet the higher bandwidth requirements of the latest 3D graphics multimedia and Internet applications The dual channel DDR3 architecture enlarges the bandwidth of your system memory to boost system performance PCI Express 2 0 support This motherboard supports PCI Express 2 0 devices for double speed and bandwidth which enhances system performance 8 channel high definition audio The onboard 8 channel HD audio High Definition Audio previously codenamed Azalia CODEC enables high quality 192KHz 24 bit audio output and jack detect feature that automatically detects and identifies what types of peripherals are plugged into the audio I O jacks and notifies users of inappropriate connection which means there will be no more confusion of Line in Line out and Mic jacks Gigabit LAN solution The onboard LAN controller is a highly integrated Gb LAN controller It is enha
21. 1ojerpey euonuau q Hedqns I Hed OA O s1ojerpey peuonuau O uedqns I ped ODA O s1ojerpey euonuajumun g uedans st ued ODA P suoneoanyIdads SULMOT OF 201 0 SUIIOJUO SM1d L9H8d L9H8d J8QUNN IPPON pieoqi ujol SWEN 9npoid jonpoad ay y s re o p Aq 1ou SSSP SO9 OTS LLLE 6EL OTS ON xBq ouoyg 6ES 6 VO Mowag Aem 27810d10D 008 ss ippy gUOntUJJJUJ Jo nduo snsy uregN va lqisuods q 8 LLOT 7 UOS T Wed DDA Jed ALIANYOHNOD HO NOLLVUV IONA
22. CPU Parameter Recall C P R feature Shut down and reboot the system then the BIOS automatically resets parameter settings to default values 1 20 ASUS P8H61 Series 1 10 Connectors 1 10 1 Rear panel connectors 1 2 3 45 10 9 8 7 6 1 PS 2 Mouse port green This port is for a PS 2 mouse 2 Parallel port This 25 pin port connects a parallel printer a scanner or other devices LAN RJ 45 port This port allows Gigabit connection to a Local Area Network LAN through a network hub Refer to the table below for the LAN port LED indications LAN port LED indications Activity Link Speed Activity Link LED Speed LED LED LED OFF No link OFF 10Mbps connection ORANGE Linked ORANGE 100Mbps connection BLINKING Data activity 1Gbps connection LAN port 4 Line In port light blue This port connects to the tape CD DVD player or other audio Sources 5 Line Out port lime This port connects to a headphone or a speaker In the 4 6 and 8 channel configurations the function of this port becomes Front Speaker Out 6 Microphone port pink This port connects to a microphone V Refer to the audio configuration table below for the function of the audio ports in 2 4 6 or 8 channel configuration Audio 2 4 6 or 8 channel configuration Headset 2 channel 4 channel 6 channel 8 channel Light Blue Rear panel Line In Rear Speaker Out Rear Speaker Out Rear Speaker Out Lime Rear panel
23. D3N9 2G low profile KVR1333D3N9 2G KVR1333D3N9 2G KHX1333C7D3K2 4GX XMP KHX1333C9D3UK2 4GX XMP KVR1333D3N9 4G low profile KVR1333D3N9 4G MT4JTF12864AZ 1G4D1 MT8JTF12864AZ 1G4F1 MT8JTF25664AZ 1G4D1 MT16JTF25664AZ 1G4F1 MT16JTF51264AZ 1G4D 1 OCZ3G1333LV3GK OCZ3F13334GK OCZ3G13334GK Chapter 1 Product introduction 1GB 3GB 3 x 1GB 2GB 2GB 2GB 2GB 1GB 1GB 3GB 3 x 1GB 3GB 3 x 1GB 1GB 24GB 6x4GB 8GB 4 x 2GB 1GB 2GB 6GB 3 x 2GB 1GB 2GB 1GB 3GB 3 x 1GB 3GB 3 x 1GB 4GB 2 x 2GB 4GB 2 x 2GB 6GB 3 x 2GB 8GB 2 x 4GB 8GB 2 x 4GB 16GB 4x 4GB 2GB 2 x 1GB 4GB 2 x 2GB 4GB 2 x 2GB 1GB 2GB 2GB 4GB 1GB 2GB 2GB 2GB 4GB 1GB 2GB 2GB 2GB 2GB 4GB 2 x 2GB 4GB 2 x 2GB 4GB 4GB 1GB 1GB 2GB 2GB 4GB 3GB 3 x 1GB 4GB 2 x 2GB 4GB 2 x 2GB A Data A Data APACER Apacer Corsair Micron Micron ELPIDA ELPIDA G SKILL GEIL HYNIX HYNIX HYNIX HYNIX KINGMAX KINGMAX KINGMAX KINGMAX KINGMAX ELPIDA HYNIX ELPIDA KTC ELPIDA HYNIX Hynix MICRON Micron MICRON Micron MICRON AD30908C8D 151C E0906 AD30908C8D 151C E0903 AM5D5808DEWSBG AM5D5808FEQSBG 9FF22D9KPT 9KF27D9KPT J1108EDSE DJ F J1108EDSE DJ F GL1L128M88BA12N H5TC1G83TFRH9A H5TQ2G83BFRH9C H5TC1G83TFRH9A H5TQ2G83BFRH9C KKB8FNWBFGNX 27A KFC8FMFXF DXX 15A DIMM socket support Optional 1DIMM 2DIMMs Voltage 1 65 1 85V 1 65 1 85V 9 S 9 9 9 24 9 9 9 24 9 9 9 24 9 9 9 24 9 9 9
24. F 45 0 C 5 160V CPU_FAN 3325RPM CHA FAN I U l I i MB 75 2 F 40 0 C 12 248V i l U i i i i Ci System Performance Performance Energy Saving Normal d Boot Priority Use the rnouse to drag or keyboard to navigate 15 decide the boot priority Boot Menu F8 Default F5 Selects the boot device priority Power Saving mode Loads optimized default Displays the system properties of the Normal mode ASUS Optimal mode selected mode on the right hand side Selects the boot device priority Z The boot device options vary depending on the devices you installed to the system The Boot Menu F8 button is available only when the boot device is installed to the system ASUS P8H61 Series Advanced Mode The Advanced Mode provides advanced options for experienced end users to configure the BIOS settings The figure below shows an example of the Advanced Mode Refer to the following sections for the detailed configurations To access the EZ Mode click Exit then select ASUS EZ Mode Back button Menu items Menu bar Configuration fields General help exit Li Main Ai Tweaker Advanced Monitor gw Back Advahced Onboard Devices Configuration gt Enabled Disabled Realtek LAN HD Audio Controller Enabled Front Panel Type HD Realtek LAN Controller Enabled Realtek PXE OPROM Realtek LAN Controller Disabled Disabled gt Serial Port Configuration Enabled gt Parallel Port Configuration lt Sele
25. H Germany and Austria Address Fax Web site Online contact Technical Support Telephone Component Telephone System Notebook Eee LCD Support Fax Online support Harkort Str 21 23 D 40880 Ratingen Germany 49 2102 959911 www asus de www asus de sales 49 1805 010923 49 1805 010920 49 2102 9599 11 support asus com EUR 0 14 minute from a German fixed landline EUR 0 42 minute from a mobile phone TIOZ OG ULF ainjeubis 7 uayg Aller oweN 039 uolllSOq lt DUDJEW AlluuoJuoo D3 LLOZ Bureu 35 Bulxiye ulB q o 1e A LLOZ LO uer jeq uoneiel5 q Burysew 223 LOLOLL 3A gooz oez9 Na O 600Z 82Z ON 03 uonenbey G007 LOEZ9 NA 600Z Z79 ON 03 uonenbey 9007 LOEZ9 Na O 800Z SZZL ON 03 uogenbay BANDE d13 23 SZL 600Z 1 800 L LW 9007 LW 7007 99009 NI o 600Z LL W 9007 L 09609 N3 X 9007 L 09609 N3 O dANDSJIG GAT 23 96 9007 L0 6007 L L LA Een ZOE NA G0 900Z Le LA Z ZS LOE NI 60 2002 L LA 9ZE ZOE NI 90 2002 z z LA Z 9Z ZOE NI 60 2002 Lv LA 77 68t LOE NA 90 6002 L L ZA ZL 68t LOE NA LL 2002 L LA 6 68 LOE NI LL S00Z Le LA 2 687 LOE NI 80 Z002 L LA t 68 LOE NI 80 2002 L Y LA 687 LOE NI v0 800Z 18 LA 1 687 LOE NI LILILILILILILILILILILI zooz sseos Na O Z00Z 1ZE0S NI L00Z 09 0S NI 10 6002 L L LA Z rrS ZOE NI 0 S00Z lv LA 68 LOE NI 90 2002 L Z N 2 806 LOE
26. I to move selection ENTER to select boot device ESC to boot using defaults 3 When the Make Disk menu appears select the FreeDOS command prompt item by pressing the item number 4 Atthe FreeDOS prompt type d and press lt Enter gt to switch the disk from Drive C optical drive to Drive D USB flash drive Welcome to FreeDOS http www freedos org C gt d D gt ASUS P8H61 Series Backing up the current BIOS To backup the current BIOS file using the BIOS Updater aN Ensure that the USB flash drive is not write protected and has at least 1024KB free space to save the file 1 Atthe FreeDOS prompt type bupdater o filename and press lt Enter gt D gt bupdater oOLDBIOS1 rom Filename Extension The filename is any user assigned filename with no more than eight alphanumeric characters for the filename and three alphanumeric characters for the extension 2 The BIOS Updater backup screen appears indicating the BIOS backup process When BIOS backup is done press any key to return to the DOS prompt ASUSTek BIOS Updater for DOS V1 18 BOARD tt BOARD MUAKkNONN VER 0220 VER Unknown DATE 01 04 2011 DATE Unknown PATH Bay BIOS backup is done Press any key to continue a BIOS Chapter 2 BIOS information 2 5 Updating the BIOS file To update the BIOS file using BIOS Updater At the FreeDOS prompt type bupdater pc g and press lt Enter gt 1 D g
27. NI 90 200Z L Z N L 806 LOE NI 0 002 2 0 6A LLS LOE NI 0 800Z L Z LA Z Obt 00 NI G0 800Z Lv LA L Obt 00 NI 90 9000 L Z LA 8Z 006 NZ BAe 311 21 23 S 666L 1 200 020SS NA 800 00019 NA 00 cV l00 1V 8661 720SS NA HS 900 2V 002 1V 1L002 E LOSS NA 9002 Z 00019 N3 D 2002 1W 9002 2z0ss N3 X seAn984IP Buimo joj ay JO SJUBWINbad Ienu ss au YIM WOJU 8A 99410 DONF 23 80 L YO0TIX SN1d LIH8d LIH8d SWEU SPON pieoqi u oNW SWEU 9npoiq snyesedde Buimo oj au asejoap ANVNY3D Auyyuno9 NAONILVY 0880r Z LZ HIS IHOMYVH Au ss ippv HO YILNdNOD SNSV redoing u Ane u s id i pezioyujyny NVMIVL Ayyuno9 0 0 Y NVMIVL ELL Id IVL NOLIAd GY 31 17 094 ON AUD sseuppy ONI YILNdNOD APLSNSV JSJNJIOBJNUEN LORDA Alt e VOGEL Eau ETI AJ1UIJOJUOS JO UO paubis4apun 34 IM HEJE 29G 93 I TOT OG uer IA SINJEUFIS 23 e JU DISS4d suey 9A9 S WEN S_UOSIOg JANBJUISIIday uoryelodo possopun sneo Aew yey 30U9I9JI9JUI SuIpNyout p AI9991I DoUdIOFJoyUI Aue Wang snur 231IA9p sm Z pue oou r jj lui njuney osned jou Aeul 3AP SIYL I suonrpuoo OM SurAo oj 201 o p fqns s uone19d0 Sammy ODA 94 JO I Hed uA S rlduto5 IMAP SUL uonguIIoJUJ 18JUIWIJddng s
28. P8H61 P8H61 PLUS Le KN CO Lo Ga eb mm aiam O e E6320 First Edition V1 January 2011 Copyright 2011 ASUSTeK Computer Inc All Rights Reserved No part of this manual including the products and software described in it may be reproduced transmitted transcribed stored in a retrieval system or translated into any language in any form or by any means except documentation kept by the purchaser for backup purposes without the express written permission of ASUSTeK Computer Inc ASUS Product warranty or service will not be extended if 1 the product is repaired modified or altered unless such repair modification of alteration is authorized in writing by ASUS or 2 the serial number of the product is defaced or missing ASUS PROVIDES THIS MANUAL AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESS OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE IN NO EVENT SHALL ASUS ITS DIRECTORS OFFICERS EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING DAMAGES FOR LOSS OF PROFITS LOSS OF BUSINESS LOSS OF USE OR DATA INTERRUPTION OF BUSINESS AND THE LIKE EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL U
29. Part No Size oe Chip Brand Chip NO Timing Voltage support Optional 1DIMM 2DIMMs rucial CT12864BA1067 8FF 1GB SS Micron 9GF22D9KPT 7 rucial CT25664BA1067 16FF 2GB DS Micron 9HF22D9KPT 7 e e ELPIDA EBJIOUESEDFO AE F 1GB SS ELPIDA J1108EDSE DJ F dee LPIDA EBJ11UD8BAFA AE E 1GB DS Elpida J5308BASE AC E S ELPIDA EBJ2i1UE8EDFO AE F 2GB DS ELPIDA J1108EDSE DJ F Ag KINGSTON KVR1066D3N7 1G 1GB SS KTC D1288JPNDPLD9YU 7 1 5V KINGSTON KVR1066D3N7 2G 2GB DS ELPIDA J1108BDSE DJ F 7 1 5V KINGSTON KVR1066D3N7 4G 4GB DS Hynix H5TQ2G83AFR 7 1 5V Micron MT8JTF12864AZ 1G1F1 1GB SS Micron 9GF22D9KPT 7 Micron MT16JTF25664AZ 1G1F1 2GB DS Micron 9HF22D9KPT 7 CZ OCZ3G1066LV4GK 4GB 2 x2GB DS Micron 9BF27D9KPV 7 7 7 20 1 65V lixir M2Y2G64CB8HC5N BE 2GB DS Elixir N2CB1G80CN BE lixir M2Y2G64CBHA9N BE 2GB DS 7 7 7 20 lixir M2Y2G64CBHC9ON BE 2GB DS Elixir Kingtiger 2GB DIMM PC3 8500 2GB DS Hynix H5TQ1G83AFP G7C SS Single sided DS Double sided DIMM support 1 DIMM Supports one module inserted into either slot as single channel memory configuration 2 DIMMs Supports one pair of modules inserted into both the blue slots as one pair of dual channel memory configuration N Visit tne ASUS website at www asus com for the latest QVL N Chapter 1 Product introduction 1 7 3 Installing a DIMM Unplug the power supply before adding or removing DIMMs or other system components
30. SE ONLY AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Offer to Provide Source Code of Certain Software This product may contain copyrighted software that is licensed under the General Public License GPL and under the Lesser General Public License Version LGPL The GPL and LGPL licensed code in this product is distributed without any warranty Copies of these licenses are included in this product You may obtain the complete corresponding source code as defined in the GPL for the GPL Software and or the complete corresponding source code of the LGPL Software with the complete machine readable work that uses the Library for a period of three years after our last shipment of the product including the GPL Software and or LGPL Software which will be no earlier than December 1 2011 either 1 for free by downloading it from http support asus com download or 2 for the cost of reproduction and shipment which is dependent on the preferred carrier and the loc
31. VSY ZNXL VIVSY AND LNXY VLVSY bdxXY VLVSY INXL VLVSY ONG O z el ONG Zz o e zi a Oci Ed P8H61 Series SATA connectors WW You must install Windows XP Service Pack 3 or later version before using Serial ATA hard disk drives When using hot plug and NCQ set the SATA Mode item in the BIOS to AHCI Mode See section 2 5 4 SATA Configuration for details 7 USB connectors 10 1 pin USB56 USB78 USB910 These connectors are for USB 2 0 ports Connect the USB module cable to any of these connectors then install the module to a slot opening at the back of the system chassis These USB connectors comply with USB 2 0 specification that supports up to 480 Mbps connection speed USB56 USB78 USB910 gt od gt see d IS roc ean THs onma amma onma NNNZO NNNZO NNNZO n 5335502 535502 55502 PIN 1 1 PIN 1 S PIN 1 a SE SERS BPH Kate 12 0 Kate O a A m a A m a Am 5509 252 2752 amp gt 3 5 3 P8H61 Series USB2 0 connectors AN Never connect a 1394 cable to the USB connectors Doing so will damage the motherboard The USB module cable is purchased separately Chapter 1 Product introduction 1 25 System panel connector 10 1 pin F_PANEL This connector supports several chassis mount
32. ally adjust depending on the chassis temperature Silent Sets to Silent to minimize the fan speed for quiet chassis fan operation Turbo Sets to Turbo to achieve maximum chassis fan speed Manual Sets to Manual to assign detailed fan speed control parameters Z The following four items appear only when you set Chassis Fan Profile to Manual Chassis Upper Temperature 70 Use the lt gt and lt gt keys to adjust the upper limit of the CPU temperature The values range from 40 C to 90 C Chassis Fan Max Duty Cycle 100 Use the lt gt and lt gt keys to adjust the maximum chassis fan duty cycle The values range from 60 to 100 When the chassis temperature reaches the upper limit the chassis fan will operate at the maximum duty cycle Chassis Lower Temperature 40 Displays the lower limit of the chassis temperature CPU Fan Min Duty Cycle 60 Use the lt gt and lt gt keys to adjust the minimum chassis fan duty cycle The values range from 60 to 100 When the chassis temperature is under 40 C the chassis fan will operate at the minimum duty cycle 2 6 5 CPU Voltage 3 3V Voltage 5V Voltage 12V Voltage The onboard hardware monitor automatically detects the voltage output through the onboard voltage regulators Select Ignore if you do not want to detect this item 2 6 6 Anti Surge Support Enabled This item allows you to enable or disable the Anti Surge function Configu
33. amage to the socket pins do not remove the PnP cap unless you are installing a CPU Retention tab ASUS P8H61 Series 3 Lift the load lever in the direction of the arrow until the load plate is completely lifted 4 Remove the PnP cap from the CPU socket by lifting the tab only 5 Position the CPU over the socket ensuring that the gold triangle is on the bottom left corner of the socket and then fit the socket alignment keys into the CPU notches The CPU fits in only one correct H orientation DO NOT force the CPU into the socket to prevent bending the connectors on the socket and damaging the CPU Chapter 1 Product introduction 6 Apply some Thermal Interface Material to the exposed area of the CPU that the heatsink will be in contact with ensuring that it is spread in an even thin layer Some heatsinks come with pre applied thermal paste If so skip this step The Thermal Interface Material is toxic and inedible DO NOT eat it If it gets into your eyes or touches your skin wash it off immediately and seek professional medical help 7 Close the load plate A and then push down the load lever B ensuring that the front edge of the load plate slides under the retention knob C 8 Insert the load lever under the retention tab ASUS P8H61 Series 1 6 2 Installing the CPU heatsink and fan The Intel LGA1155 processor requires a specially designed heatsink and fan a
34. ation where you want to have it shipped to by sending a request to ASUSTeK Computer Inc Legal Compliance Dept 15 Li Te Rd Beitou Taipei 112 Taiwan In your request please provide the name model number and version as stated in the About Box of the product for which you wish to obtain the corresponding source code and your contact details so that we can coordinate the terms and cost of shipment with you The source code will be distributed WITHOUT ANY WARRANTY and licensed under the same license as the corresponding binary object code This offer is valid to anyone in receipt of this information ASUSTeK is eager to duly provide complete source code as required under various Free Open Source Software licenses If however you encounter any problems in obtaining the full corresponding source code we would be much obliged if you give us a notification to the email address gpl asus com stating the product and describing the problem please do NOT send large attachments such as source code archives etc to this email address Contents NOU ann vi LENA telen d ur uuu u uuu u genet vii ABDOU UNIS ULT vii P8H61 Series specifications summary ix Chapter 1 Product introduction 1 1 1 2 1 3 1 4 1 5 1 6 1 7 1 8 1 9 1 10 W eg REE EE 1 1 PACKAGE Comten IS uadressert 1 1 beet EE 1 1 1 3 1 Product highlights
35. autious when changing the settings of the Ai Tweaker menu items Incorrect field values can cause the system to malfunction The configuration options for this section vary depending on the CPU and DIMM model you installed on the motherboard ZE Ka EFI BIOS Utility Advanced Mode Q Ai Tweaker Advanced Monitor Boot X M P When XMP is enabled BCLK frequency CPU ratio and memory parameters will be auto optimized Memory Frequency Auto EPU Power Saving MODE Disabled gt OC Tuner gt DRAM Timing Control gt CPU Power Management CPU Offset Mode Sign lt Select Screen CPU Voltage TL Select Item Enter Select DRAM Voltage Change Opt F1 General Help VCCIO Voltage F2 Previous Values F5 Optimized Defaults CPU PLL Voltage F10 Save ESC Exit PCH Voltage Version 2 00 1201 Copyright C 2010 American Megatrends Inc Scroll down to display the following items Load Line Calibration Auto Auto PSI Enabled CPU Spread Spectrum Auto Version 2 00 1201 Copyright C 2010 American Megatrends Inc Target DRAM Speed xxxxMHz Displays the current DRAM speed 2 4 1 Ai Overclock Tuner Auto Allows you to select the CPU overclocking options to achieve the desired CPU internal frequency Select any of these preset overclocking configuration options Auto Loads the optimal settings for the system Manual Allows you to individually set overclocking parameters Chapter 2 BIOS i
36. card 2 Remove the system unit cover if your motherboard is already installed in a chassis 3 Remove the bracket opposite the slot that you intend to use Keep the screw for later use 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot 5 Secure the card to the chassis with the screw you removed earlier 6 Replace the system cover 1 8 2 Configuring an expansion card After installing the expansion card configure it by adjusting the software settings 1 Turn on the system and change the necessary BIOS settings if any See Chapter 2 for information on BIOS setup 2 Assign an IRQ to the card 3 Install the software drivers for the expansion card aN When using PCI cards on shared slots ensure that the drivers support Share IRQ or that the cards do not need IRQ assignments Otherwise conflicts will arise between the two PCI groups making the system unstable and the card inoperable 1 8 3 PCI slots The PCI slots support cards such as a LAN card SCSI card USB card and other cards that comply with PCI specifications 1 8 4 PCI Express x1 slots This motherboard supports PCI Express x1 network cards SCSI cards and other cards that comply with the PCI Express specifications 1 8 5 PCI Express x16 slot This motherboard has a PCI Express 2 0 x16 slot that supports PCI Express x16 2 0 graphic cards complying with the PCI Express specifications Chapt
37. ct Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F5 Optimized Defaults F10 Save ESC Exit Version 2 00 12 1 Copyright C 2010 American Megatrends Inc Submenu item Pop up window Scroll bar Navigation keys Menu bar The menu bar on top of the screen has the following main items For changing the basic system configuration Ai Tweaker For changing the overclocking settings Advanced For changing the advanced system settings Monitor For displaying the system temperature power status and changing the fan settings For changing the system boot configuration For configuring options for special functions For selecting the exit options and loading default settings Chapter 2 BIOS information 2 9 Menu items The highlighted item on the menu bar displays the specific items for that menu For example selecting Main shows the Main menu items The other items Ai Tweaker Advanced Monitor Boot Tool and Exit on the menu bar have their respective menu items Back button This button appears when entering a submenu Press lt Esc gt or use the USB mouse to click this button to return to the previous menu screen Submenu items A greater than sign gt before each item on any menu screen means that the item has a submenu To display the submenu select the item and press lt Enter gt Pop up window Select a menu item and press lt Enter gt to display a pop up window
38. e system fails to boot after changing any BIOS setting try to clear the CMOS and reset the motherboard to the default value See section 1 9 Jumpers for information on how to erase the RTC RAM Chapter 2 BIOS information 2 7 2 8 BIOS menu screen The BIOS setup program can be used under two modes EZ Mode and Advanced Mode You can change modes from the Exit menu or from the Exit Advanced Mode button in the EZ Mode Advanced Mode screen EZ Mode By default the EZ Mode screen appears when you enter the BIOS setup program The EZ Mode provides you an overview of the basic system information and allows you to select the display language system performance mode and boot device priority To access the Advanced Mode click Exit Advanced Mode then select Advanced Mode Z The default screen for entering the BIOS setup program can be changed Refer to the Setup Mode item in section 2 7 Boot menu for details Selects the display language of Clicks to display all fan the BIOS setup program speeds if available CPU SV 3 3V 12V voltage output the changes saves the changes and resets CPU chassis fan speed the system or enters the Advanced Mode Exit Advanced Mode i i Rete English Y i BIOS Version 0210 Build Date 01 04 2011 CPU Type Intel R Core TM i5 2500 CPU 0 3 30GHz Speed 3300 MHz Friday 10 08 2010 Total Memory 1024 MB DDR3 1333MHz z 1 Temperature Voltage KR Fan Speed CPU 113 0
39. ed functions P mE sO P8H61 Series F PANEL PLED PIN 1 mm fa m PLED Ground mg PWR E Io mj HD LED HD LED a P8H61 Series System panel connector System power LED 2 pin PLED This 2 pin connector is for the system power LED Connect the chassis power LED cable to this connector The system power LED lights up when you turn on the system power and blinks when the system is in sleep mode Hard disk drive activity LED 2 pin HDLED This 2 pin connector is for the HDD Activity LED Connect the HDD Activity LED cable to this connector The IDE LED lights up or flashes when data is read from or written to the HDD Power Soft off button 2 pin PWRBTN This 2 pin connector is for the system power button Reset button 2 pin RESET This 2 pin connector is for the chassis mounted reset button for system reboot without turning off the system power ASUS P8H61 Series 1 11 Software support 1 11 1 Installing an operating system This motherboard supports Windows XP Vista 7 Operating Systems OS Always install the latest OS version and corresponding updates to maximize the features of your hardware Z Motherboard settings and hardware options vary Refer to your OS documentation for detailed information Ensure that you
40. emperature MB Temperature xxx C xxx F The onboard hardware monitor automatically detects and displays the CPU and motherboard temperatures Select Ignore if you do not wish to display the detected temperatures 2 6 2 CPU Chassis Fan Speed xxxx RPM or Ignore N A The onboard hardware monitor automatically detects and displays the CPU and chassis fan speeds in rotations per minute RPM If the fan is not connected to the motherboard the field shows N A Select Ignore if you do not wish to display the detected speed Chapter 2 BIOS information 2 23 2 24 2 6 3 CPU Q Fan Control Enabled Disabled Disables the CPU Q Fan control feature Enabled Enables the CPU Q Fan control feature CPU Fan Speed Low Limit 600 RPM This item appears only when you enable the CPU Q Fan Control feature and allows you to disable or set the CPU fan warning speed Configuration options Ignore 200 RPM 300 RPM 400 RPM 500 RPM 600 RPM CPU Fan Profile Standard This item appears only when you enable the CPU Q Fan Control feature and allows you to set the appropriate performance level of the CPU fan Standard Sets to Standard to make the CPU fan automatically adjust depending on the CPU temperature Silent Sets to Silent to minimize the fan speed for quiet CPU fan operation Turbo Sets to Turbo to achieve maximum CPU fan speed Manual Sets to Manual to assign detailed fan speed control parameters The f
41. en press lt Enter gt 4 Confirm the password when prompted To clear the administrator password follow the same steps as in changing an administrator password but press lt Enter gt when prompted to create confirm the password After you clear the password the Administrator Password item on top of the screen shows Not Installed User Password If you have set a user password you must enter the user password for accessing the system The User Password item on top of the screen shows the default Not Installed After you set a password this item shows Installed To set a user password 1 Select the User Password item and press lt Enter gt 2 From the Create New Password box key in a password then press lt Enter gt 3 Confirm the password when prompted To change a user password 1 Select the User Password item and press lt Enter gt 2 From the Enter Current Password box key in the current password then press lt Enter gt 3 From the Create New Password box key in a new password then press lt Enter gt 4 Confirm the password when prompted To clear the user password follow the same steps as in changing a user password but press lt Enter gt when prompted to create confirm the password After you clear the password the User Password item on top of the screen shows Not Installed ASUS P8H61 Series 2 4 Ai Tweaker menu The Ai Tweaker menu items allow you to configure overclocking related items Be c
42. ent 2 14 2 4 7 Offset Mode Sign 2 15 2 48 DRAM Voltage 2 16 24 9 VOCIO Voltage rerrarernnrnravvernrrennvrrnvrernvsesvrerseresresenenens 2 16 2 4 10 CPU PLL Voltage 2 16 24211 PET Voll8 8 eee 2 16 2 4 12 Load Line Calibration 2 16 2413 AP 2 16 2 4 14 CPU Spread Spectrum 2 16 Advanced NC E 2 17 2 5 1 CPU COME Lane 2 17 2 5 2 System Agent Configuration 2 19 258 PCH Configuration 2 19 2 5 4 SATA Configuration eeeseeeeeeeeeeeereererrrrrrerrrrrrnrrerenne 2 19 Contents 2 6 2 7 2 8 2 9 255 USB Configuration 2 20 2 5 6 Onboard Devices Configuration 2 20 207 APN E 2 21 Monitor Cu UE 2 23 2 6 1 CPU Temperature MB Temperature 2 23 2 6 2 CPU Chassis Fan Speed 2 23 2 6 3 CPU Q Fan Control 2 24 2 6 4 Chassis Q Fan Control 2 24 2 6 5 CPU Voltage 3 3V Voltage 5V Voltage 12V Voltage 2 25 2 6
43. er 1 Product introduction 1 19 1 9 Jumpers Clear RTC RAM 3 pin CLRTC This jumper allows you to clear the Real Time Clock RTC RAM in CMOS You can clear the CMOS memory of date time and system setup parameters by erasing the CMOS RTC RAM data The onboard button cell battery powers the RAM data in CMOS which include system setup information such as system passwords oy EL e E CLRTC 1 2 2 3 EJ Ge 0 m Normal Clear RTC DCH Co mum ee Default P8H61 Series Clear RTC RAM To erase the RTC RAM 1 Turn OFF the computer and unplug the power cord 2 Move the jumper cap from pins 1 2 default to pins 2 3 Keep the cap on pins 2 3 for about 5 10 seconds then move the cap back to pins 1 2 3 Plug the power cord and turn ON the computer 4 Hold down the lt Del gt key during the boot process and enter BIOS setup to re enter data AN Except when clearing the RTC RAM never remove the cap on CLRTC jumper default position Removing the cap will cause system boot failure Ifthe steps above do not help remove the onboard battery and move the jumper again to clear the CMOS RTC RAM data After clearing the CMOS reinstall the battery You do not need to clear the RTC when the system hangs due to overclocking For system failure due to overclocking use the
44. find the BIOS file and then press lt Enter gt to perform the BIOS update process Reboot the system when the update process is done 3 This function supports USB flash disks with FAT 32 16 format and single partition only DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure 2 1 3 ASUS CrashFree BIOS 3 utility The ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process You can restore a corrupted BIOS file using the motherboard support DVD or a USB flash drive that contains the updated BIOS file aN Before using this utility rename the BIOS file in the removable device into P8H61 ROM for P8H61 or H61PLUS ROM for P8H61 PLUS s The BIOS file in the support DVD may not be the latest version Download the latest BIOS file from the ASUS website at www asus com Recovering the BIOS To recover the BIOS 1 Turn on the system 2 Insert the support DVD to the optical drive or the USB flash drive that contains the BIOS file to the USB port 3 The utility automatically checks the devices for the BIOS file When found the utility reads the BIOS file and enters ASUS EZ Flash 2 utility automatically 4 The system requires you to enter BIOS Setup to recover BIOS setting To ensure system compatibility and stability we recommend that you press lt F5 gt to load default BIOS values AN DO NOT
45. get to connect the fan cables to the fan connectors Insufficient air flow inside the system may damage the motherboard components These are not jumpers Do not place jumper caps on the fan connectors Z The CPU_FAN connector supports a CPU fan of maximum 2A 24 W fan power 5 Digital audio connector 4 1 pin SPDIF_OUT This connector is for an additional Sony Philips Digital Interface S PDIF port Connect the S PDIF Out module cable to this connector then install the module to a slot opening at the back of the system chassis P CR CH 5 Pene Seia O L gt aQ o 66 HERH ad OCC CY re SPDIF OUT P8H61 Series Digital audio connector Z The S PDIF module is purchased separately 1 24 ASUS P8H61 Series 6 Intel H61 Serial ATA 3 0Gb s connectors 7 pin SATA3G_1 4 These connectors connect to Serial ATA 3 0 Gb s hard disk drives and optical drives via Serial ATA 3 0 Gb s signal cables o SATA3G 4 SATA3G 3 l l GND RSATA TXP4 GND RSATA RXP4 GND GND RSATA TXP3 GND RSATA RXP3 GND RSATA_TXN4 RSATA_RXN4 RSATA_TXN3 RSATA_RXN3 gt gt O O N gt gt O O bdXL VIVSE ZdXL VIVSY ON CNN VIVSY ZdXY4 VI
46. herwise the system will not boot up We recommend that you use a PSU with higher power output when configuring a system with more power consuming devices The system may become unstable or may not boot up if the power is inadequate e If you are uncertain about the minimum power supply requirement for your system refer to the Recommended Power Supply Wattage Calculator at http support asus com PowerSupplyCalculator PSCalculator aspx SLanguage en us for details 3 Speaker connector 4 pin SPEAKER The 4 pin connector is for the chassis mounted system warning speaker The speaker allows you to hear system beeps and warnings co cunmf SPEAKER INO seyeeds AG AND AND PIN 1 P8H61 Series Speaker out connector Chapter 1 Product introduction 1 23 4 CPU and chassis fan connectors 4 pin CPU FAN 3 pin CHA FAN Connect the fan cables to the fan connectors on the motherboard ensuring that the black wire of each cable matches the ground pin of the connector CPU_FAN GND CPU FAN IN CPU FAN PWR CPU FAN PWM CHA FAN p Rotation o 12V Eee SS GND DCH m ome P8H61 Series fan connectors Do not for
47. igation keys and brief online help to guide you in using the BIOS Setup program Entering BIOS Setup at startup To enter BIOS Setup at startup Press lt Delete gt during the Power On Self Test POST If you do not press lt Delete gt POST continues with its routines Entering BIOS Setup after POST To enter BIOS Setup after POST Press lt Ctrl gt lt Alt gt lt Del gt simultaneously e Press the reset button on the system chassis Press the power button to turn the system off then back on Do this option only if you failed to enter BIOS Setup using the first two options Using the power button reset button or the lt Ctrl gt lt Alt gt lt Del gt keys to force reset from a running operating system can cause damage to your data or system We recommend to always shut down the system properly from the operating system w The BIOS setup screens shown in this section are for reference purposes only and may not exactly match what you see on your screen Visit the ASUS website at www asus com to download the latest BIOS file for this motherboard Ensure that a USB mouse is connected to your motherboard if you want to use the mouse to control the BIOS setup program If the system becomes unstable after changing any BIOS setting load the default settings to ensure system compatibility and stability Select the Load Optimized Defaults item under the Exit menu See section 2 9 Exit Menu for details If th
48. iguration options Auto I0 378h IRQ 5 lO 378h IRQ 5 6 7 9 10 11 12 I0 278h IRQ 5 6 7 9 10 11 12 IO 3BCh IRQ 5 6 7 9 10 11 12 Device Mode STD Printer Mode Allows you to select the Printer Port mode Configuration options STD Printer Mode SPP Mode EPP 1 9 and SPP Mode EPP 1 7 and SPP Mode ECP Mode ECP and EPP 1 9 Mode ECP and EPP 1 7 Mode 2 5 7 APM Restore AC Power Loss Power Off Power On The system goes into on state after an AC power loss Power Off The system goes into off state after an AC power loss Last State The system goes into either off or on state whatever the system state was before the AC power loss Power On By PS 2 Keyboard Disabled Disabled Disables the Power On by a PS 2 keyboard Space Bar Sets the Space Bar on the PS 2 keyboard to turn on the system Ctrl Esc Sets the Ctrl Esc key on the PS 2 keyboard to turn on the system Power Key Sets Power key on the PS 2 keyboard to turn on the system This feature requires an ATX power supply that provides at least 1A on the 5VSB lead Power On By PS 2 Mouse Disabled Disabled Disables the Power On by a PS 2 mouse Enabled Enables the Power On by a PS 2 mouse This feature requires an ATX power supply that provides at least 1A on the 5VSB lead Power On By PCI Disabled Disabled Disables the PME to wake up from S5 by PCI devices Enabled Allows you to turn on the system through a PCI LAN or modem card Th
49. ing type auto using the keyboard and press lt Enter gt Changing the values in this menu may cause the system to become unstable If this happens revert to the default settings 2 4 6 CPU Power Management The sub items in this menu allow you to set the CPU ratio and features CPU Ratio Auto Allows you to manually adjust the maximum non turbo CPU ratio Use lt gt and lt gt keys or the numeric keypad to adjust the value The valid value ranges vary according to your CPU model ASUS P8H61 Series Enhanced Intel SpeedStep Technology Enabled Allows you to enable or disable the Enhanced Intel SpeedStep Technology EIST Disabled Disables this function Enabled The operating system dynamically adjusts the processor voltage and core frequency which may result in decreased average consumption and decreased average heat production Turbo Mode Enabled This item appears only when you set the Enhanced Intel SpeedStep Technology item to Enabled Enabled Allows processor cores to run faster than marked frequency in specific conditions Disabled Disables this function Z The following five items appear only when you set both the Enhanced Intel SpeedStep Technology and Turbo Mode items to Enabled Long duration power limit Auto Use the lt gt and lt gt keys to adjust the value Long duration maintained Auto Use the lt gt and lt gt keys to adjust the value Short duration power lim
50. install Windows XP Service Pack 3 or later versions Windows Vista Service Pack 1 or later versions before installing the drivers for better compatibility and system stability 1 11 2 Support DVD information The Support DVD that comes with the motherboard package contains the drivers software applications and utilities that you can install to avail all motherboard features Z The contents of the Support DVD are subject to change at any time without notice Visit the lt ASUS website at www asus com for updates To run the Support DVD Place the Support DVD to the optical drive The DVD automatically displays the Drivers menu if Autorun is enabled in your computer VA The following screen is for reference only Drivers display Support DVD motherboard information ASUS InstAl MD sik Click an icon to select items to install Intel Chipset Driver Realtek Audio Driver Realtek LAN Driver Browser Configuration Utility Management Engine Interface Norton Internet Security 2011 Click an item to install P If Autorun is NOT enabled in your computer browse the contents of the Support DVD to locate the file ASSETUP EXE from the BIN folder Double click the ASSETUP EXE to run the DVD Chapter 1 Product introduction 1 27 ASUS P8H61 Series BIOS information 2 1 Managing and updating your BIOS 3 Save a copy of the original motherboard BIOS file to a USB flash disk in case you need to restore the
51. is feature requires an ATX power supply that provides at least 1A on the 5VSB lead Chapter 2 BIOS information 2 21 2 22 Power On By PCIE Disabled Disabled Disables the PCIE devices to generate a wake event Enabled Enables the PCIE devices to generate a wake event Power On By Ring Disabled Disabled Disables Ring to generate a wake event Enabled Enables Ring to generate a wake event Power On By RTC Disabled Disabled Disables RTC to generate a wake event Enabled When set to Enabled the items RTC Alarm Date Days and Hour Minute Second will become user configurable with set values ASUS P8H61 Series 2 6 Monitor menu The Monitor menu displays the system temperature power status and allows you to change the fan settings gem wm Main Ai Tweaker Advanced Monitor MB Temperature CPU Fan Speed Chassis Fan Speed CPU Q Fan Control Enabled CPU Fan Speed Low Limit 600 RPM CPU Fan Profile Standard Chassis Q Fan Control Enabled Chassis Fan Speed Low Limit 600 RPM lt Select Screen TL Select Item Chassis Fan Profile Standard Enter Select Change Opt CPU Voltage i alues 3 3V Voltage Fay je ed Defaults F10 Save ESC Exit 5V Voltage 12V Voltage Version 2 00 1201 Copyright C 2010 American Megatrends Inc Scroll down to display the following items Anti Surge Support Enabled Version 2 00 1201 Copyright C 2010 American Megatrends Inc 2 6 1 CPU T
52. it Auto Use the lt gt and lt gt keys to adjust the value Primary Plane Current Limit Auto Use the lt gt and lt gt keys to adjust the value Secondary Plane Current Limit Auto Use the lt gt and lt gt keys to adjust the value 2 4 7 Offset Mode Sign To offset the voltage by a positive value To offset the voltage by a negative value CPU Voltage Auto Allows you to set the Offset voltage The values range from 0 630V to 0 630V with a 0 010V interval l Refer to the CPU documentation before setting the CPU voltage Setting a high voltage may damage the CPU permanently and setting a low voltage may make the system unstable Chapter 2 BIOS information 2 15 2 16 2 4 8 DRAM Voltage Auto Allows you to set the DRAM voltage The values range from 1 185V to 2 135V with a 0 005V interval According to Intel CPU specification DIMMs with voltage requirement over 1 65V may damage the CPU permanently We recommend you install the DIMMs with the voltage requirement below 1 65V 2 4 9 VCCIO Voltage Auto Allows you to set the VCCIO voltage The values range from 0 735V to 1 685V with a 0 005V interval 2 4 10 CPU PLL Voltage Auto Allows you to set the CPU and PCH PLL voltage The values range from 1 80V to 1 90V with a 0 1V interval 2 4 11 PCH Voltage Auto Allows you to set the Platform Controller Hub voltage The values range from 0 735V to 1 685V with a 0
53. les Place six screws into the holes indicated by circles to secure the motherboard to the chassis Do not overtighten the screws Doing so can damage the motherboard FII Place this side towards the rear of the chassis Je EE P8H61 Series ESE lea C m EE ASUS P8H61 Series 1 5 3 Motherboard layout 1 3 20 3cm 8 0in 2 4 LGA1155 E LAN_USB12 BH CPU FAN DL ATX12V Si S S 5 ke ke O E E E E T Ke lt lt N N ire G st st DDR3 DIMM_A1 DDR3 DIMM_B1 1 T Ss g CH Lithium Cell N m H s S AUDIO E x fea AAFP CHA_FAN lt 7 Rem S O P8H61 Series RTL SE PCIEX16 E Super I O Intel 5 BIOS 887 Lal e SED OUT O USB56 USB78 USB910 F_PANEL SATA3G 2 SATA3G 1 sawe pnr fm nr I e o j C y y 12 11 10 9 8 7 1 5 4 Layout contents Connectors Jumpers Slots LED ATX power connectors 24 pin EATXPWR 4 pin ATX12V CPU and chassis fan connectors 4 pin CPU_FAN 3 pin CHA_FAN Intel LGA1155 CPU socket DDR3 DIMM slots Clear RTC RAM 3 pin CLRTC Intel H61 Serial ATA 3 0Gb s connectors 7 pin SATA3G_1 2 3 4 Chapter 1 Product introduction Connectors Jumpers Slots LED Speaker connector 4 pin SPEAKER System panel connector 10 1 pin PANEL 1 26 USB connectors 10 1 pin USB56 USB78 1 25 USB910 Standby power LED SB_PWR 1 5 Digital audio connector 4 1 pin SPDIF_OUT
54. nced with an ACPI management function to provide efficient power management for advanced operating systems 100 All High quality Conductive Polymer Capacitors P8H61 PLUS only This motherboard uses all high quality conductive polymer capacitors for durability improved lifespan and enhanced thermal capacity Innovative ASUS features ASUS EFI BIOS EZ Mode ASUS brand new EFI BIOS offers a user friendly interface that goes beyond traditional keyboard BIOS input to enable more flexible and convenient mouse controls You can easily navigate the new EFI BIOS with the same smoothness as their operating system The exclusive EZ Mode displays frequently accessed setup info while the Advanced Mode is for experienced performance enthusiasts that demand far more intricate system settings ASUS P8H61 Series SN Auto Tuning Fan Xpert CrashFree BIOS 3 ASUS TurboV Feel the adrenaline rush of real time OC now a reality with the ASUS TurboV This easy OC tool allows you to overclock without exiting or rebooting the OS and its user friendly interface makes overclock with just a few clicks away Moreover the ASUS OC profiles in TurboV provides the best O C settings in different scenarios Auto Tuning Auto Tuning is an intelligent tool that automates overclocking to achieve a total system level up This tool also provides stability testing Even O C beginners can achieve extreme yet stable overclocking results with Aut
55. nector We recommend that you connect a high definition front panel audio module to this connector to avail of the motherboard s high definition audio capability If you want to connect a high definition front panel audio module to this connector set the Front Panel Type item in the BIOS setup to HD If you want to connect an AC 97 front panel audio module to this connector set the item to AC97 By default this connector is set to HD See section 2 5 6 Onboard Devices Configuration for details ASUS P8H61 Series 2 ATX power connectors 24 pin EATXPWR 4 pin ATX12V These connectors are for ATX power supply plugs The power supply plugs are designed to fit these connectors in only one orientation Find the proper orientation and push down firmly until the connectors completely fit 12V DC 12V DC EEL GND GND ATX12V EATXPWR 3 Volts GND 12 Volts 5 Volts 12 Volts 5 Volts 5V Standby 5 Volts Power OK 5 Volts GND GND 5 Volts GND GND GND 5 Volts PSON GND GND 3 Volts 12 Volts 3 Volts 3 Volts PIN 1 P8H61 Series ATX power connectors LN Fora fully configured system we recommend that you use a power supply unit PSU that complies with ATX 12 V Specification 2 0 or later version and provides a minimum power of 350 W DO NOT forget to connect the 4 pin ATX 12V power plug Ot
56. nformation 2 13 2 14 BCLK PEG Frequency XXX This item appears only when you set the Al Overclock Tuner item to Manual and allows you to adjust the CPU and VGA frequency to enhance the system performance Use the lt gt and lt gt keys to adjust the value You can also key in the desired value using the numeric keypad The values range from 80MHz to 300MHz 2 4 2 Memory Frequency Auto Allows you to set the memory operating frequency Configuration options DDR3 800MHz DDR3 1066MHz DDR3 1333MHz AD Selecting a very high memory frequency may cause the system to become unstable If this happens revert to the default setting 2 4 3 EPU Power Saving Mode Disabled Allows you to enable or disable the EPU power saving function Configuration options Disabled Enabled EPU Setting Auto This item appears only when you set the EPU Power Saving MODE item to Enabled and allows you to select the EPU power saving mode Configuration options Auto Light Power Saving Mode Medium Power Saving Mode Max Power Saving Mode 2 4 4 OC Tuner Disabled OC Tuner automatically overclocks the frequency and voltage of CPU and DRAM for enhancing the system performance Press lt Enter gt and select OK to start automatic overclocking 2 4 5 DRAM Timing Control The sub items in this menu allow you to set the DRAM timing control features Use the lt gt and lt gt keys to adjust the value To restore the default sett
57. nstructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment to an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help 4 The use of shielded cables for connection of the monitor to the graphics card is required to assure compliance with FCC regulations Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user s authority to operate this equipment Canadian Department of Communications Statement This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications This class B digital apparatus complies with Canadian ICES 003 REACH Complying with the REACH Registration Evaluation Authorisation and Restriction of Chemicals regulatory framework we published the chemical
58. ntroller to use as the primary boot device Configuration options PCI PEG PEG PCI 2 5 3 PCH Configuration High Precision Timer Enabled Allows you to enable or disable the High Precision Event Timer Configuration options Enabled Disabled 2 5 4 SATA Configuration While entering Setup the BIOS automatically detects the presence of SATA devices The SATA Port items show Not Present if no SATA device is installed to the corresponding SATA port SATA Mode IDE Mode Allows you to set the SATA configuration Disabled Disables the SATA function IDE Mode Set to IDE Mode when you want to use the Serial ATA hard disk drives as Parallel ATA physical storage devices AHCI Mode Set to AHCI Mode when you want the SATA hard disk drives to use the AHCI Advanced Host Controller Interface The AHCI allows the onboard storage driver to enable advanced Serial ATA features that increases storage performance on random workloads by allowing the drive to internally optimize the order of commands Serial ATA Controller 0 Enhanced This item appears only when you set the SATA Mode item to IDE Mode Disabled Disables the SATA function Enhanced Set to Enhanced to support more than four SATA devices Compatible Set to Compatible when using Windows 98 NT 2000 MS DOS Up to four SATA devices are supported under these operating systems Serial ATA Controller 1 Enhanced This item appears only when you set the SATA M
59. o Tuning ASUS Anti Surge Protection This special design prevents expensive devices and the motherboard from damage caused by power surges from switching power supply PSU Al Suite II With its fast user friendly interface ASUS Al Suite II consolidates all the exclusive ASUS features into one simple to use software package It allows you to supervise overclocking energy management fan speed control and voltage and sensor readings This all in one software offers diverse and ease to use functions with no need to switch back and forth between different utilities ASUS EPU ASUS EPU is a unique power saving technology that detects the current system loadings and adjusts the power consumption in real time Fan Xpert ASUS Fan Xpert intelligently allows you to adjust the CPU and chassis fan speeds according to different ambient temperatures caused by different climate conditions in different geographic regions and your PC s loading The built in variety of useful profiles offer flexible controls of fan speed to achieve a quiet and cool environment ASUS MyLogo2 This feature allows you to convert your favorite photo into a 256 color boot logo for a more colorful and vivid image on your screen ASUS CrashFree BIOS 3 ASUS CrashFree BIOS 3 is an auto recovery tool that allows you to restore a corrupted BIOS file using the bundled support DVD or USB flash disk that contains the latest BIOS file Chapter 1 Product introduc
60. ode item to IDE Mode Disabled Disables the SATA function Enhanced Set to Enhanced to support more than four SATA devices S M A R T Status Check Enabled S M A R T Self Monitoring Analysis and Reporting Technology is a monitor system When read write of your hard disk errors occur this feature allows the hard disk to report warning messages during the POST Configuration options Enabled Disabled Chapter 2 BIOS information 2 19 2 20 2 5 5 USB Configuration The items in this menu allow you to change the USB related features The USB Devices item shows the auto detected values If no USB device is detected the item shows None Legacy USB Support Enabled Enabled Enables the support for USB devices on legacy operating systems OS Disabled The USB devices can be used only for the BIOS setup program Auto Allows the system to detect the presence of USB devices at startup If detected the USB controller legacy mode is enabled If no USB device is detected the legacy USB support is disabled EHCI Hand off Disabled Enabled Enables the support for operating systems without an EHCI hand off feature Disabled Disables the function 2 5 6 Onboard Devices Configuration HD Audio Controller Enabled Enabled Enables the High Definition Audio Controller Disabled Disables the controller P The following two items appear only when you set the HD Audio Controller item to Enabled
61. ogy Disabled Forces the XD feature flag to always return to zero 0 Intel Virtualization Technology Disabled Enabled Allows a hardware platform to run multiple operating systems separately and simultaneously enabling one system to virtually function as several systems Disabled Disables this function Enhanced Intel SpeedStep Technology Enabled Allows you to enable or disable the Enhanced Intel SpeedStep Technology EIST Disabled The CPU runs at its default speed Enabled The operating system controls the CPU speed Turbo Mode Enabled This item appears only when you set the Enhanced Intel SpeedStep Technology item to Enabled and allows you to enable or disable the Intel Turbo Mode Technology Enabled Allows processor cores to run faster than marked frequency in specific condition Disabled Disables this function CPU C1E Enabled Enabled Enables the C1E support function This item should be enabled in order to enable the Enhanced Halt State Disabled Disables this function CPU C3 Report Enabled Allows you to disable or enable the CPU C3 report to the operating system Configuration options Disabled Enabled CPU C6 Report Enabled Allows you to disable or enable the CPU C6 report to the operating system Configuration options Enabled Disabled ASUS P8H61 Series 2 5 2 System Agent Configuration Initiate Graphic Adapter PEG PCI Allows you to decide which graphics co
62. ollowing four items appear only when you set CPU Fan Profile to Manuall CPU Upper Temperature 70 Use the lt gt and lt gt keys to adjust the upper limit of the CPU temperature The values range from 20 C to 75 C CPU Fan Max Duty Cycle 100 Use the lt gt and lt gt keys to adjust the maximum CPU fan duty cycle The values range from 20 to 100 When the CPU temperature reaches the upper limit the CPU fan will operate at the maximum duty cycle CPU Lower Temperature 20 Displays the lower limit of the CPU temperature CPU Fan Min Duty Cycle 20 Use the lt gt and lt gt keys to adjust the minimum CPU fan duty cycle The values range from 0 to 100 When the CPU temperature is under 40 C the CPU fan will operate at the minimum duty cycle 2 6 4 Chassis Q Fan Control Enabled Disabled Disables the Chassis Q Fan control feature Enabled Enables the Chassis Q Fan control feature Chassis Fan Speed Low Limit 600 RPM This item appears only when you enable the Chassis Q Fan Control feature and allows you to disable or set the chassis fan warning speed Configuration options Ignore 200 RPM 300 RPM 400 RPM 500 RPM 600 RPM ASUS P8H61 Series Chassis Fan Profile Standard This item appears only when you enable the Chassis Q Fan Control feature and allows you to set the appropriate performance level of the chassis fan Standard Sets to Standard to make the chassis fan automatic
63. om the options Configuration options Chinese Trad Chinese Simp Japanese French Deutsch English 2 3 2 System Date Day xx xx xxxx Allows you to set the system date 2 3 3 System Time xx xx xx Allows you to set the system time 2 3 4 Security The Security menu items allow you to change the system security settings Z If you have forgotten your BIOS password erase the CMOS Real Time Clock RTC RAM to clear the BIOS password See section 1 9 Jumpers for information on how to erase the RTC RAM The Administrator or User Password items on top of the screen show the default Not Installed After you set a password these items show Installed Chapter 2 BIOS information 2 11 Administrator Password If you have set an administrator password we recommend that you enter the administrator password for accessing the system Otherwise you might be able to see or change only selected fields in the BIOS setup program To set an administrator password 1 Select the Administrator Password item and press lt Enter gt 2 From the Create New Password box key in a password then press lt Enter gt 3 Confirm the password when prompted To change an administrator password 1 Select the Administrator Password item and press lt Enter gt 2 From the Enter Current Password box key in the current password then press lt Enter gt 3 From the Create New Password box key in a new password th
64. on a grounded antistatic pad or in the bag that came with the component Before you install or remove any component ensure that the ATX power supply is switched off or the power cord is detached from the power supply Failure to do so may cause severe damage to the motherboard peripherals or components Standby Power LED The motherboard comes with a standby power LED that lights up to indicate that the system is ON in sleep mode or in soft off mode This is a reminder that you should shut down the system and unplug the power cable before removing or plugging in any motherboard component The illustration below shows the location of the onboard LED SB PWR ON OFF Standby Power Powered Off Chapter 1 Product introduction 1 5 1 5 Motherboard overview Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it d Ensure that you unplug the power cord before installing or removing the motherboard Failure to do so can cause you physical injury and damage motherboard components 1 5 1 Placement direction When installing the motherboard ensure that you place it into the chassis in the correct orientation The edge with external ports goes to the rear part of the chassis as indicated in the image below 1 5 2 Screw ho
65. ormation to prevent injury to yourself when trying to complete a task i CAUTION Information to prevent damage to the components when trying to y complete a task LN IMPORTANT Instructions that you MUST follow to complete a task E NOTE Tips and additional information to help you complete a task Where to find more information Refer to the following sources for additional information and for product and software updates 1 ASUS websites The ASUS website provides updated information on ASUS hardware and software products Refer to the ASUS contact information 2 Optional documentation Your product package may include optional documentation such as warranty flyers that may have been added by your dealer These documents are not part of the standard package Typography Bold text Indicates a menu or an item to select Italics Used to emphasize a word or a phrase lt Key gt Keys enclosed in the less than and greater than sign means that you must press the enclosed key Example lt Enter gt means that you must press the Enter or Return key lt Key1 gt lt Key2 gt lt Key3 gt If you must press two or more keys simultaneously the key names are linked with a plus sign Example lt Ctrl gt lt Alt gt lt D gt P8H61 Series specifications summary LGA1155 socket for Intel Second Generation Core i7 Core i5 Core i3 processors Supports 32nm CPU Supports Intel Turbo Boost technology 2
66. ration options Disabled Enabled Chapter 2 BIOS information 2 25 2 26 2 7 Boot menu The Boot menu items allow you to change the system boot options ASUS EFI BIOS Utility Advanced Mode Main Ai Tweaker Advanced Monitor Select the keyboard NumLock state Full Screen Logo Enabled Option ROM Messages Force BIOS Setup Mode EZ Mode Boot Option 1 SATA xXXXXXX Boot Option 42 SATA XXXXXXX gt SATA XXXXXXXXXXXX lt Select Screen TL Select Item gt SATA 000 0000 00004 Enter Select Change Opt gt Hard Drive BBS Priorities F1 General Help F2 Previous Values gt CD DVD ROM Drive BBS Priorities F5 Optimized Defaults F10 Save ESC Exit Version 2 00 1201 Copyright C 2010 American Megatrends Inc 2 7 1 Bootup NumLock State On On Sets the power on state of the NumLock to On Off Sets the power on state of the NumLock to Off 2 7 2 Full Screen Logo Enabled Enabled Enables the full screen logo display feature Disabled Disables the full screen logo display feature Set this item to Enabled to use the ASUS MyLogo 2 feature 2 7 3 Option ROM Messages Force BIOS Force BIOS The third party ROM messages will be forced to display during the boot sequence Keep Current The third party ROM messages will be displayed only if the third party manufacturer had set the add on device to do so 2 7 4 Setup Mode EZ Mode Advanced Mode Set
67. roken do not try to fix it by yourself Contact a qualified service technician or your retailer Operation safety Before installing the motherboard and adding devices on it carefully read all the manuals that came with the package Before using the product ensure that all cables are correctly connected and the power cables are not damaged If you detect any damage contact your dealer immediately To avoid short circuits keep paper clips screws and staples away from connectors slots sockets and circuitry Avoid dust humidity and temperature extremes Do not place the product in any area where it may become wet Place the product on a stable surface If you encounter technical problems with the product contact a qualified service technician or your retailer About this guide This user guide contains the information you need when installing and configuring the motherboard How this guide is organized This guide contains the following parts Chapter 1 Product introduction This chapter describes the features of the motherboard and the new technology it supports Chapter 2 BIOS information This chapter tells how to change system settings through the BIOS Setup menus Detailed descriptions of the BIOS parameters are also provided vii viii Conventions used in this guide To ensure that you perform certain tasks properly take note of the following symbols used throughout this manual DANGER WARNING Inf
68. rs gt System Agent Configuration gt PCH Configuration gt SATA Configuration gt USB Configuration gt Onboard Devices Configuration gt APM lt Select Screen TL Select Item Enter Select Change Opt F1 General Help F2 Previous Values F5 Optimized Defaults F10 Save ESC Exit Version 2 00 1201 Copyright C 2010 American Megatrends Inc 2 5 1 CPU Configuration The items in this menu show the CPU related information that the BIOS automatically detects A The items shown in submenu may be different due to the CPU you installed CPU Ratio Auto Allows you to set the ratio between the CPU Core Clock and the BCLK Frequency Use lt gt and lt gt keys or the numeric keypad to adjust the ratio The valid value ranges vary according to your CPU model Intel Adaptive Thermal Monitor Enabled Enabled Enables the overheated CPU to throttle its clock speed to cool down Disabled Disables the CPU thermal monitor function Chapter 2 BIOS information 2 17 Active Processor Cores All Allows you to choose the number of CPU cores to activate in each processor package Configuration options All 1 2 3 Limit CPUID Maximum Disabled Enabled Allows legacy operating systems to boot even without support for CPUs with extended CPUID functions Disabled Disables this function Execute Disable Bit Enabled Enabled Enables the No Execution Page Protection Technol
69. s Advanced Mode as the default screen for entering the BIOS setup program EZ Mode Sets EZ Mode as the default screen for entering the BIOS setup program ASUS P8H61 Series 2 7 5 Boot Option Priorities These items specify the boot device priority sequence from the available devices The number of device items that appears on the screen depends on the number of devices installed in the system Es To select the boot device during system startup press lt F8 gt when ASUS Logo appears To access Windows OS in Safe Mode do any of the following Press lt F5 gt when ASUS Logo appears Press lt F8 gt after POST 2 7 6 Boot Override These items displays the available devices The number of device items that appears on the screen depends on the number of devices installed in the system Click an item to start booting from the selected device Chapter 2 BIOS information 2 27 2 28 2 8 Tools menu The Tools menu items allow you to configure options for special functions Select an item then press lt Enter gt to display the submenu Ai Tweaker Advanced Monitor Be used to update BIOS gt ASUS EZ Flash Utility gt ASUS SPD Information gt ASUS O C Profile 2 8 1 ASUS EZ Flash Utility Allows you to run ASUS EZ Flash 2 ASUS EZ Flash 2 screen appears Z For more details see section 2 1 2 ASUS EZ Flash 2 2 8 2 ASUS SPD Information DIMM Slot Slot 1 Displays the Serial Presence De
70. ssembly to ensure optimum thermal condition and performance aN e When you buy a boxed Intel processor the package includes the CPU fan and heatsink assembly If you buy a CPU separately ensure that you use only Intel certified multi directional heatsink and fan Your Intel LGA1155 heatsink and fan assembly comes in a push pin design and requires no tool to install Use an LGA1155 compatible CPU heatsink and fan assembly only The LGA1155 socket is incompatible with the LGA775 and LGA1366 sockets in size and dimension If you purchased a separate CPU heatsink and fan assembly ensure that you have e properly applied Thermal Interface Material to the CPU heatsink or CPU before you install the heatsink and fan assembly Z Ensure that you have installed the motherboard to the chassis before you install the CPU e fan and heatsink assembly To install the CPU heatsink and fan 1 Place the heatsink on top of the installed CPU ensuring that the four fasteners match the holes on the motherboard Orient the heatsink and fan assembly such that the CPU fan cable is closest to the CPU fan connector 2 Push down two fasteners at a time in a diagonal sequence to secure the heatsink and fan assembly in place Z The type of CPU heatsink and fan assembly may differ but the installation steps and functions should remain the same The illustration above is for reference only Chapter 1 Product introduction 1 11 3
71. substances in our products at ASUS REACH website at http csr asus com english REACH htm DO NOT throw the motherboard in municipal waste This product has been designed to enable proper reuse of parts and recycling This symbol of the crossed out wheeled bin indicates that the product electrical and electronic equipment should not be placed in municipal waste Check local regulations for disposal of electronic products DO NOT throw the mercury containing button cell battery in municipal waste This symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste Safety information Electrical safety To prevent electric shock hazard disconnect the power cable from the electric outlet before relocating the system When adding or removing devices to or from the system ensure that the power cables for the devices are unplugged before the signal cables are connected If possible disconnect all power cables from the existing system before you add a device Before connecting or removing signal cables from the motherboard ensure that all power cables are unplugged Seek professional assistance before using an adapter or extension cord These devices could interrupt the grounding circuit Ensure that your power supply is set to the correct voltage in your area If you are not sure about the voltage of the electrical outlet you are using contact your local power company If the power supply is b
72. t W1333UB4GS 4GB DS Samsung K4B2G0846C uper Talent W1333UX6GM 6GB 3x 2GB DS Micron OBF27D9KPT 9 9 9 24 1 5V lixir M2F2G64CB88B7N CG 2GB DS Elixir N2CB2G808N CG lixir M2Y2G64CB8HA9N CG 2GB DS 7 7 7 20 lixir M2Y2G64CB8HC9ON CG 2GB DS Elixir lixir M2F4G64CB8HB5N CG 4GB DS Elixir N2CB2G808N CG INGSHARE KSRPCD313332G 2GB DS PATRIOT PM128M8D385 15 Kingtiger 2GB DIMM PC3 10666 2GB De Smaa I ingtiger KTG2G1333PG3 2GB DS ATRIOT PSD31G13332H 1GB DS 9 ATRIOT PSD31G13332 1GB DS Patriot PM64M8D38U 15 PATRIOT PSD32G13332H 2GB DS AMAXEL RMR1870ED48E8F 1333 2GB DS ELPIDA J1108BDBG DJ F SILICON SP001GBLTU133S01 1GB SS NANYA NTSCB128M8AN CG 9 SILICON POWER GEN SP002GBLTU133S02 2GB DS elixir N2CB1680AN C6 9 TAKEMS TMS1GB364D081 107EY 1GB SS 7 7 7 20 1 5V AKEMS TMS1GB364D081 138EY 1GB SS S 8 8 8 24 1 5V TAKEMS TMS2GB364D081 107EY 2GB DS 7 7 7 20 1 5V TAKEMS TMS2GB364D081 138EY 2GB 8 8 8 24 1 5V TAKEMS TMS2GB364D082 138EW 2GB DS 8 8 8 24 1 5V MAX E41302GP0 73BDB 2GB DS UMAX U2S24D30TP 13 i WINTEC 3WVS31333 2G CNR 2GB DS AMPO AM3420803 13H OCZ3G1333LV4GK OCZ3P1333LV4GK OCZ3X13334GK XMP 4GB OCZ3G1333LV6GK 6GB OCZ3P1333LV6GK 6GB 2 x 2GB 3 x 2GB LZ LS g DA D O N OVV U D U U DRIR QO O O O O ep co Wal m m A SP001GBLTU133S02 1GB SS elixir N2CB1680AN C6 9 g We ASUS P8H61 Series DDR3 1066 MHz capability sei DIMM socket Vendors
73. t bupdater pc g The BIOS Updater screen appears as below ASUSTek BIOS Updater for DOS V1 18 BOARD ESHOT BOARD WnkKnown VER 0220 VER Unknown DATE 01 04 2001 DATE Unknown PATH BEN P8H61 ROM 4194304 2011 01 04 17 30 48 Enter Select or Load Tab Switch V Drive Info Up Down Home End Move B Backup Esc Exit Press lt Tab gt to switch between screen fields and use the lt Up Down Home End gt keys to select the BIOS file and press lt Enter gt BIOS Updater checks the selected BIOS file and prompts you to confirm BIOS update Are you sure to update BIOS Select Yes and press lt Enter gt When BIOS update is done press lt ESC gt to exit BIOS Updater Restart your computer AN DO NOT shut down or reset the system while updating the BIOS to prevent system boot failure 3 For BIOS Updater version 1 04 or later the utility automatically exits to the DOS prompt after updating BIOS Ensure to load the BIOS default settings to ensure system compatibility and stability Select the Load Optimized Defaults item under the Exit menu Refer to section 2 9 Exit menu for details Ensure to connect all SATA hard disk drives after updating the BIOS file if you have disconnected them 2 6 ASUS P8H61 Series 2 2 BIOS setup program Use the BIOS Setup program to update the BIOS or configure its parameters The BIOS screens include nav
74. t to change without notice Product introduction 1 1 Welcome Thank you for buying an ASUS P8H61 Series motherboard The motherboard delivers a host of new features and latest technologies making it another standout in the long line of ASUS quality motherboards Before you start installing the motherboard and hardware devices on it check the items in your package with the list below 1 2 Package contents Check your motherboard package for the following items Motherboard ASUS P8H61 Series motherboard Cables 2 x Serial ATA 3 0Gb s cables Accessories 1 x I O shield Application DVD ASUS motherboard support DVD Documentation User Manual Z P8H61 Series motherboards include P8H61 and P8H61 PLUS two models The package contents vary from models H any of the items is damaged or missing contact your retailer 1 3 Special features 1 3 1 Product highlights DA GE Intel LGA1155 Intel Second Generation Core i7 Core i5 Core i3 processors This motherboard supports the Intel second generation Core i7 Core i5 Core i3 processors in LGA1155 package with memory and PCI Express controllers integrated to support 2 channel 2 DIMMs DDR3 memory and 16 PCI Express 2 0 lanes This provides great graphics performance Intel second generation Core i7 Core i5 Core i3 processors are among the most powerful and energy efficient CPUs in the world Chapter 1 Product introduction
75. tect SPD information of the DIMM module installed on the selected slot Configuration options Slot 1 Slot 2 2 8 3 ASUS O C Profile This item allows you to store or load multiple BIOS settings Z The Setup Profile Status items show Not Installed if no profile is created Save to Profile Allows you to save the current BIOS settings to the BIOS Flash and create a profile Key ina profile number from one to eight press lt Enter gt and then select Yes Load from Profile Allows you to load the previous BIOS settings saved in the BIOS Flash Key in the profile number that saved your CMOS settings press lt Enter gt and then select Yes DO NOT shut down or reset the system while updating the BIOS to prevent the system boot failure We recommend that you update the BIOS file only coming from the same memory CPU configuration and BIOS version ASUS P8H61 Series 2 9 Exit menu The Exit menu items allow you to load the optimal default values for the BIOS items and save or discard your changes to the BIOS items You can access the EZ Mode from the Exit menu Load Optimized Defaults Save Changes amp Reset Discard Changes amp Exit ASUS EZ Mode Launch EFI Shell from filesystem device Load Optimized Defaults This option allows you to load the default values for each of the parameters on the Setup menus When you select this option or if you press lt F5 gt a confirmation window appears
76. tion 1 3 E a EL Flash2 ASUS EZ Flash 2 ASUS EZ Flash 2 is a utility that allows you to update the BIOS without using an OS based utility C P R CPU Parameter Recall The BIOS C P R feature automatically restores the CPU default settings when the system hangs due to overclocking failure C P R eliminates the need to open the system chassis and clear the RTC data Simply shut down and reboot the system and the BIOS automatically restores the CPU parameters to their default settings ErP ready The motherboard is European Union s Energy related Products ErP ready and ErP requires products to meet certain energy efficiency requirements in regards to energy consumptions This is in line with ASUS vision of creating environment friendly and energy efficient products through product design and innovation to reduce carbon footprint of the product and thus mitigate environmental impacts ASUS P8H61 Series 1 4 Before you proceed Take note of the following precautions before you install motherboard components or change any motherboard settings AN Unplug the power cord from the wall socket before touching any component Before handling components use a grounded wrist strap or touch a safely grounded object or a metal object such as the power supply case to avoid damaging them due to static electricity Hold components by the edges to avoid touching the ICs on them Whenever you uninstall any component place it

ASUS P8H61 Owner's Manual

Contents

Download Pdf Manuals

Related Search

Related Contents