HFP4x3compact operators manual - Home page
Contents
1. Hfp 4x3 compact Remove the packaging but leave the machine on the wooden base Warning Before you push the handle down on the machine turn the 4 pressure screws on the back of the machine so the printing head and the printing pattern do not touch Check the distance by pushing the handle down slowly being careful not to hit the printing head and the printing platens together The tension spring wing nut will have to be kept under tension at all times This is located at the back of the machine between the 4 tension screws On the temperature controller there are four keys You only need to push the up and down keys only Do not push the set Key or the side arrow key As it has been pre programmed 1 Always turn of the machine when not in use Hfp 4x3 compact operator s manual Getting to know the machine parts temperature controller chase adjusting the machine Top foil bar slots Handle 4 Pressure screws Printing platern 1 Tension wing nut 3 amp fuse Heater plate Foil receiver Heater connector box i i F j Temperature Contro 2 chase tension screws Ali chase Mains switch Dog clips printing plate Top foil bar Foil holder Mains 220v ac 3 amps fitted fuse fitted at rear of the control box Temperature controller model xmt 7100 Trilite Equipment Connection live Connection 2 neutral Connection 3 earth Connection 4 feed Connection 5 output to heater Connection 6 blue temp s2. block touches the press phan but not under tension by turning the knobs clock wise or anti clockwise as required 2 The tension spring wing nut will have to be kept under tension at all times This is located at the back of the machine between the 4 tension screws Do a Test print 1 Photocopy and Print the exact size envelop on your printer and trim to size and fold 2 Place the photocopy print on the presspahn 3 Pull the handle down to the print position and adjust the bottom gauge bar so it is below the printing plate 4 Then adjust the 4 pressure screws until it starts to an even embossed onto the paper 5 Now you can re adjust the bottom gauge bar to where you would like the print to be on the envelopes Feeding the foil into the machine Put the foil onto the top foil roller place it on top of the machine with the shinny side of the foil facing downwards and over the top of the top foil bar ba Faltin Fo t A TE aoe aE And then under the bottom front foil bar and onto the back foil receiver stuck down with a bit of tape Do a test print and then adjust the pressure screws bottom gauge bar or side stop 1f required or until you get the best results Once you are happy with the print you can then start printing the envelops When printing lift up the flap on the envelop so you printing onto one flat surface Adjusting the foil advance The foil TA in the maximum position T he an a in n the mi
3. ensors Connection 7 yellow temp sensors Cartridge heater 22 5 w 230vac 6 5x100mm Max print sizes 100 mm x 75mm Setting the Temperature controller When you first switch on the machine the temperature will start at about 15 25 degrees c and after about 2 minutes the temperature will start to rise to the set temperature setting Reset the temperature to 100 degrees c Set the temperature by pressing the up or down arrow key on the controller to set the temperature and wait for the machine to reach the set temperature Please ignore the 2 other Keys on the Controller Attach the magnesium printing plate to the chase Put the 2 dog clips on the chase and Attach the magnesium printing plate into the centre of the chase buy locking with the 4 grub screw on the dog clips in the vertical position with the Allen key provided Attaching the numbering block to the chase Attach the number block to the chase into the centre of the chase buy locking with the 4 grub screw on the dog clips in the horizontal position with the alen key provided Slide the chase into position on the heater block Setting up the printing platen 1 Screw the bottom gauge bar to the bottom of the printing platen making sure that when you pull the handle down it doesn t hit the printing plate 2 Place a peace of press phan onto the printing platen Adjusting the 4 pressure screws 1 Adjust the 4 pressure screw until the magnesium plate or numbering
4. nimum position
Download Pdf Manuals
Related Search