OPERATORS MANUAL
Contents
1. 3 5mm 2 If the laminating pouch does not go in straight or gets stuck during lamination press and hold down the reverse button Wait until the pouch film is out completely then remove it immediately A4 H OT amp C O L D so that the end will not bend due to overheating 4 This unit is equipped with auto shut down device after being on 3 5mm LAMI NATI A G MAC ReH i A fe CLEANING THE ROLLER the reverse indicator will light to reverse the laminating for 8 hours This is to prevent over heating of the unit The ready lt Should the laminating machine be used for a long period of time you will notice a residue of additives pouch back to the entrance power indicator will blink following the beeping signals which is left on the rollers This residue has come from the pouch during lamination So cleaning the OPERATING INSTRUCTIONS continues Offis gt LAMINATING continued l S Fig 4 3 When the pouch film is out from the exit do not remove it by force 5 When you have finished laminating make sure to turn off the power and disconnect the plug Model OLM004 rollers periodically is necessary 1 Turn the laminator on for about 30 minutes 2 Fold the copy paper into half and let it pass through the rollers for about 10 times to clean the additive residuals on the rollers CLEANING THE MACHINE 1 Before cleaning this machine make sure it is turned off and unplugged Wipe with soft cloth 3 When necessary wipe with ne2. for laminating Make sure that the total thickness to be laminated is not more than 0 6mm DO NOT put the laminating pouch in crookedly as this will prevent the pouch film getting stuck during lamination SPECIFICATIONS Model Number Voltage Power consumption Weight Maximum width of laminating pouch Maximum thickness of laminating pouch Speed of lamination 50HzZ 6OHz Number of rollers Temperature settings Ready indicator Photo laminating Reverse function Cold laminating Thickness of pouch samples 80 micron each flap Reverse indicator Entrance Reverse Button Ready Indicator f Power Indicator ON OFF Button SETTING UP e Install the back directing pad next to the exit of the laminator see fig1 amp 2 e Next to the exit install the back directing pad to the unit e Make sure that there is no object obstructing the exit to the laminator e Insert the power plug into the mains power supply Press the ON button There will be a beep and the red power button will come on Fig 2 G OPERATING INSTRUCTIONS Before use it is advisable to try out and become familiar with the laminating process We advise that you practice with none original artwork This unit is equipped with an adjustable temperature control system Please make sure that an appropriate temperature is selected for the items being laminated When the reading indicator stays on and there is a beep the lami
3. nator has reached the correct temperature This may take up to 15 minutes When selecting a higher temperature with the temperature adjustor the ready indicator will temporarily go off whilst heating up When the desired temperature is reached the ready indicator will light again Now it is ready to laminate items that require a higher temperature COLD LAMINATING THE REASON FOR COLD LAMINATING Cold laminating is for protecting materials that might be damaged by heat such as photographs and print outs from ink jet prints HOW IT WORKS Cold laminating pouches use pressure to laminate your heat sensitive documents Pressure is used to cause an adhesive to bind the laminating material to the item being laminated 1 It is recommended to carry out the cold lamination before hot lamination to avoid waiting for the system to cool down Use a special Lamicold film for cold lamination Turn the temperature button to COLD Position the document to be laminated within the film turn the button to ON Your document comes out of the back of the laminated machine Laminated documents can be trimmed to size if required ole a LAMINATING Sealed Side 1 Before laminating make sure to leave at least 3 5mm space PIE 3 at the edges of the laminating pouch see fig 3 amp 4 Make sure that it is not crooked Send the sealed side of the laminating pouch into the entrance of laminating machine A carrier sheet is not required when
4. using this machine Laminating Pouch Film Laminating Item 3
5. utral cleaning agent and rub off with a clean cloth TROUBLE SHOOTING AND ITS CAUSES The pouch is not sufficiently well sealed or the lamination has opaque areas on the document ma e The temperature is too low Switch the setting button towards a higher temperature e When the green ready light is on the laminating machine is ready again Repeat the lamination operation using the new temperature setting The laminated document has folds or is deformed gepr fte Sicherheit PRODUCT SERVICE e The temperature is too high Turn the temperature button slightly towards a lower temperature setting Repeat the lamination operation using the new temperature setting SWISS HOUSE OPERATORS MANUAL Wigston Works Leicester England Please retain this information for future reference CAUTION Please read this manual before use Install the laminating machine on a stable work surface close to an easily accessible socket Leave enough space behind the machine to let the documents pass freely from the machine To prevent electric shocks DO NOT use the laminating machine close to water DO NOT spill water on the laminating machine nor on the lead or on the socket DO NOT use the laminating machine if the electric lead is damaged DO NOT leave the electric lead in contact with a warm surface DO NOT leave the electric lead hanging from a cupboard or a shelf DO NOT laminate metal objects Only use special film
Download Pdf Manuals
Related Search