USER GUIDE NEO
Contents
1. Release F C will flash 3 times and the setpoint temperature will flash Press or until the display shows the same as the actual measured room temperature Store by pressing for 5 seconds The heater will now work with the temperature displayed by Neo and after a period this will correspond with the actual temperature of the room This procedure can be repeated at a later date to ensure correct calibration Reset the thermostat to factory default values mode Nb Reset is not possible if the thermostat display is in any flashing After resetting the thermostat has to be reprogrammed according to the instructions for your chosen mode Switch the heater OFF Hold in the key and then switch the heater ON Hold the key in for more than 5 seconds until rE starts flashing in the display Release F and HO Home Mode will flash You can select between modes HO OF Office and CA Cabin by pressing the or keys Confirm your choice by pressing the key for more than 5 seconds 22 C will flash Select your pre ferred comfort temperature Confirm by pressing in the key for more than 5 seconds If you do nothing 22 C will auto matically be stored after 7 seconds CABIN MODE CA Important to know In cabin mode any temperature you select will be automatically saved The reason Should someone leave the cabin having sel2. keeping doors and windows closed This makes certain that Neo that is controlling room temperature Hold down on and press once on Release C will flash 3 times and the setpoint temperature will flash Press or until the display shows the same as the actual measured room temperature Store by pressing for 5 seconds The heater will now work with the temperature displayed by Neo and af ter a period this will correspond with the actual temperature of the room This procedure can be repeated at a later date to ensure correct calibration Reset the thermostat to factory default values Nb Reset is not possible if the thermostat display is in any flashing mode g N After resetting the thermostat has to be reprogrammed according to the instructions for your chosen mode Switch the heater OFF Hold in the key and then switch the heater ON Hold the key in for more than 5 seconds until rE starts flashing in the display Release F and HO Home Mode will flash You can select between modes HO OF Office and CA Cabin by pressing the or keys Confirm your choice by pressing the key for more than 5 seconds 22 C will flash Select your pre ferred comfort temperature Confirm by pressing in the key for more than 5 seconds If you do nothing 22 C will auto matically be stored after 7 seconds INSTALLATI
3. key for more than 5 seconds If you do nothing 22 C will be stored automatically after 7 seconds Startup procedure B if the heater has never been switched on since leaving the factory aa EF ce Cs Cs C HO When the heater is switched on HO Home mode will flash in the display on can select between modes HO OF Office and CA Cabin by pressing the or O key Confirm your choice by pressing in key for more than 5 seconds 22 C will flash Select your preferred comfort temperature Confirm by pressing in the key more than 5 seconds If you do nothing 22 C will be stored automatically after 7 seconds Starting the temperature cutback function ia Working overtime Three hours before you usually leave the office press down on for 5 seconds e g At 14 00 2 PM press for 5 seconds gt h hours will flash for three seconds then 12 hours will flash Select the number of hours you want cutback to be active by pressing or NB Cutback will start after three hours Confirm by pressing briefly d day will be displayed steadily for three seconds Then a random number will flash 1 Monday 2 Tuesday etc Select the correct day using or and confirm by pressing briefly C will flash three times and then 17 C will flash continuously Wit
4. ALAXX NEO USER GUIDE Day Desired set temperature 3 Heat on off 4 Night Function key 5 6 Day temperature cutback 5 days 7 ight temperature cutback 7 days A brief description of the NEO heater s functions There are three modes to choose from 1 HO Home is suitable for private homes It allows you to choose automatic temperature cutback at night and during weekdays At the weekend there will be no daytime cutback OF office mode is suitable for offices and rooms used similarly This mode gives you temperature cutback at night and from Friday evening to Monday morning If working overtime you may easily override the cutback CA Cabin mode allows you keep a low cutback temperature when the cabin is not in use and the system will switch to comfort temperature for your arrival Periods of temperature cutback may last from 1 to 40 days continuously However the cutback period you have selected will repeat itself automatically after 48 hours of comfort temperature Once made settings are easily overridden and you are free to select the temperature and duration of the cut back periods to meet your particular requirements HOME MODE HO Startup and Reset must be carried out after a long power cut or at first time use A Startup Reset procedure has to be performed to initiate the correct mode and function of the heater IMPORTANT there are two different startup sequences 1
5. If C 17 rE is flashing in the display go to procedure A 2 If HO is flashing in the display go to procedure B The procedure must be completed in one continuous sequence to be valid Should the procedure be performed incorrectly or fail switch off the heater and start a new reset procedure Startup procedure A if the heater has been connected and switched on beforehand N On switching heater on the sequence C 17 rE will flash in the display This means that the thermostat has been disconnected for a long period Ct and needs to be restarted L To set the heater back to the factory default switch off the heater using the main switch Press and hold in and then switch on using the main power switch Continue to press until rE flashes in the display then release After a few seconds HO will flash in the display You can choose between the modes HO OF Office and CA Cabin by pressing the or key Confirm your choice by pressing in the key for more than 5 seconds 22 C will flash Select your preferred comfort temperature Confirm by pressing in the key for more than 5 seconds If you do nothing 22 C will auto matically be stored after 7 seconds Startup procedure B if the heater has never been switched on since leaving the factory When the heater is switched on HO Home mode will flash in
6. ON GUIDE ise wnn a GS fN 00000 NP 370 NL 200 FE 000000080 Oil fumes for appr 5 min Please note that this symbol Automatic reset of overheating safeguard Clean monthly during periods of use means Do not cover The appliance is not intended for use by persons including children with reduced physical sensory or mental capabili ties or lack of experience and knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety Children should be supervised to ensure they do not play with the appliance If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid a hazard www adax no s
7. duration of temperature cutback and or the cutback temperature oun A 1x2 i i a J oh 8 Cm Co oo Hold down on and press twice on or Release and h hours will flash 3 times Using the or key select the number of hours you want the cutback to last Confirm by pressing key briefly If you have first pressed to change the daytime cutback settings d will now flash three times and a random number is displayed Use the or key to select the correct day Monday 1 etc Confirm by pressing briefly C will flash 3 times and then the cur rent cutback temperature will flash With or key select the cutback temperature Confirm by pressing key briefly Permanently delete cutback function To permanently delete a temperature cutback function press O or until the green lamp goes out To lock Press O and at the same time until you see in the display To unlock Press O and at the same time until you see disappear in the display Calibration cr 20 C Should the actual room temperature and Neo s setting not correspond Neo should be calibrated First let the heater work at the same temperature setting preferably for at least 24 hours keeping doors and windows closed This makes certain that Neo that is regulating room tem perature Hold do
8. e temperature will be key The number can be from 01 to We displayed and LEDs 7 and 5 will flash 40 days slowly Confirm by pressing When the temperature cutback period ends S At the time the frost safe period ends the comfort temperature setting will flash to indicate the need for action Press any key to make the comfort temperature display steadily and that temperature will now continue If you do nothing while the display is flashing another frost safe period will start automatically after 48 hours Cancelling a frost safe period S o gs To end an ongoing frost safe period press for more than 5 seconds Selecting a new cutback temperature setting o ee y 11 li Darl Ss A O Child lock om a When cutback temperature is ongoing select the new cutback temperature you desire by pressing or Save the setting by pressing more than 5 seconds To lock Press D and at the same time until you see in the display To unlock Press and at the same time until you see disappear in the display Calibration 7 ac e gg N l 2 X A Gan Oat S gt Ox 6s Should the actual room temperature and Neo s setting not correspond Neo should be calibrated First let the heater work at the same temperature setting preferably for at least 24 hours
9. ected a low frost safe temperature without any further action this setting will be saved and will continue after a power cut whatever its length This will ensure that unattended periods will always have a low temperature setting and energy consumption will stay at a minimum After a long power cut the heater will start up with the lower temperature setting whether it is the comfort or the cutback value Startup and Reset must be carried out after a long power cut or at first time use A Startup Reset procedure has to be performed to initiate the correct mode and function of the heater IMPORTANT there are two different startup sequences 1 If C 17 rE is flashing in the display go to procedure A 2 If HO is flashing in the display go to procedure B The procedure must be completed in one continuous sequence to be valid Should the procedure be performed incorrectly or fail switch off the heater and start a new reset procedure Startup procedure A if the heater has been connected and Startup procedure B if the heater has never been switched on switched on beforehand since leaving the factory gt On switching heater on the When the heater is switched on HO sequence C 17 rE will flash E io Home mode will flash in the display TILI o la in the display This means that the thermostat has been disconnected for a long period C E gt rE and needs to be restarted You can select between m
10. h the or key select your preferred cutback temperature Confirm by pressing key briefly Comfort temperature will continue for three hours before the cutback starts automatically E g At 17 00 5 PM the cutback period will start and the LED 1 will flash slowly During the cutback period the LED 1 will flash slowly When it is lit stead ily it indicates that cutback function is not currently active but will start at the appropriate time of the evening Press for 5 seconds The set comfort temperature will show in the display The LED above the key will light steady while the LED above the key will continue flashing You now have a temporary comfort period lasting five hours To cancel a period of temperature cutback 7 S O Ge Hold down on and press once on to override the currently active period or the next period of temperature cutback The lamp is lit steadily for the period in question Temperature cutback periods will resume as usual from the following period Temperature override JJ o AR SEE o Ka C Dla y If you select another temperature during either a comfort or a cutback period and do not save by pressing for five seconds the new temperature will apply only to the current period To select a new cutback temperature setting pE C Ss While cutback temperature is ongo ing choose the desired new cutback
11. ing the key briefly d will flash 3 times and then a random number Using the or key enter the cor rect day of the week Monday 1 etc Confirm by pressing the key briefly C will flash 3 times and then 17 C will flash continuously With or key select your preferred cutback temperature Confirm by pressing key briefly The green lamp 1 will now flash slowly to indicate that temperature cutback is active The temperature is reduced for the number of hours you have chosen This will be repeated at the same times from Monday to Friday leaving Saturday and Sunday unaffected Canceling a period of temperature cutback Hold down and press once on or to override the current active period or the next period of tempera ture cutback The lamp is lit steadily for the period in question Tempera ture cutback will resume as usual from the subsequent period Temperature override a Ss Selecting another temperature during either a comfort or cutback period without storing it by pressing for 5 seconds will apply only to the current period Change the temperature setting comfort or cutback TE y i A O When in the comfort or cutback temperature mode choose your new comfort or cutback temperature by pressing or Save the setting by pressing more than 5 seconds Change the
12. odes HO OF Office and CA Cabin by pressing the or O key To set the heater back to the factory FO Confirm your choice by pressing in default switch off the heater using the Dy key for more than 5 seconds main power switch Press F and hold in and at the same time switch on using the main power switch Continue to press until rE flashes in the display then release 22 C will flash Select your preferred oe comfort temperature Confirm by pressing in the key more After a few seconds HO will flash in Ans than 5 seconds the display oe If you do nothing 22 C will be stored automatically after 7 seconds You can choose between the modes HO Home OF Office and CA Cabin by pressing the or key Confirm your choice by holding in the key for more than 5 seconds 22 C will flash Select your preferred comfort temperature Confirm by holding in the key for more than 5 seconds If you do nothing 22 C will be stored automatically after 7 seconds 10 C will flash Press for 5 seconds d ays will flash 3 times 01 days will flash Select the frost safe temperature with continuously y4 the or key T Confirm by pressing Select the number of days you want the period to last by pressing the or Yi The frost saf
13. p Reset procedure has to be performed to initiate the correct mode and function of the heater IMPORTANT there are two different startup sequences 1 If C 17 rE is flashing in the display go to procedure A 2 If HO is flashing in the display go to procedure B The procedure must be completed in one continuous sequence to be valid Should the procedure be performed incorrectly or fail switch off the heater and start a new reset procedure Startup procedure A if the heater has been connected and switched on beforehand T a XN N z f o i a A eS pp N co I oo N Tn d oo On switching heater on the sequence C 17 1E will flash in the display This means that the thermostat has been disconnected for a long period and needs to be restarted To set the heater back to the factory default switch off the heater using the main power switch Press and hold in and at the same time switch on using the main power switch Continue to press until rE flashes in the display then release After a few seconds HO will flash in the display You can choose between the modes HO Home OF Office and CA Cabin by pressing the or key Confirm your choice by holding in the key for more than 5 seconds 22 C will flash Select your preferred comfort temperature Confirm by holding in the
14. temperature by pressing or Save the setting by pressing more than five seconds Change the duration of temperature cutback and or the cutback temperature Hold down on and press twice on or Release F and h hours will flash 3 times Using the or key select the number of hours you want the cutback to last Confirm by pressing key briefly d day will be displayed for three seconds and afterwards a random number Using the and keys select the correct weekday Monday etc Press briefly to confirm C will flash 3 times and then the cur rent cutback temperature will flash With or key select the cutback temperature Confirm by pressing key briefly Permanently delete cutback function To permanently delete a temperature cutback function press O or until the green lamp goes out To lock Press O and at the same time until you see in the display To unlock Press and at the same time until you see disappear in the display Calibration 7 Should the actual room temperature and Neo s setting not correspond Neo should be calibrated First let the heater work at the same temperature setting preferably for at least 24 hours keeping doors and windows closed This makes certain that Neo that is controlling room temperature Hold down on and press once on
15. the display You can select between modes HO OF Office and CA Cabin by pressing the or O key Confirm your choice by pressing in key for more than 5 seconds 22 C will flash Select your preferred comfort temperature Confirm by pressing in the key more than 5 seconds If you do nothing 22 C will auto matically be stored after 7 seconds Start nighttime temperature cutback At the time you wish temperature cut back to start press for 5 seconds h hours will flash 3 times and then 07 will flash continuously With the or key select the number of hours you want the cutback to last Confirm by pressing the key briefly C will flash 3 times and then 17 C will flash continuously Using the or key select the cut back temperature Confirm by pressing key briefly The green lamp 4 will now flash slowly to indicate that temperature cutback is active The temperature is reduced for the number of hours you have chosen This will be repeated for the same period every night Start daytime temperature cutback N At the time you wish temperature cut back to start press for 5 seconds A h hours will flash 3 times and then 05 will flash continuously Using the or key select the number of hours you want the tem perature cutback to last Confirm by press
16. wn on and press once on Release C will flash 3 times and the setpoint temperature will flash Press or until the display shows the same as the actual measured room temperature Store by pressing for 5 seconds The heater will now work with the temperature displayed by Neo and af ter a period this will correspond with the actual temperature of the room This procedure can be repeated at a later date to ensure correct calibration Reset the thermostat to factory default values Nb Reset is not possible if the thermostat display is in any flashing mode Va N After resetting the thermostat has to be reprogrammed according to the instructions for your chosen mode Switch the heater OFF Hold in the key and then switch the heater ON Hold the key in for more than 5 seconds until rE starts flashing in the display Release and HO Home Mode will flash You can select between modes HO OF Office and CA Cabin by pressing the or keys Confirm your choice by pressing the key for more than 5 seconds 22 C will flash Select your pre ferred comfort temperature Confirm by pressing in the key for more than 5 seconds If you do nothing 22 C will auto matically be stored after 7 seconds OFFICE MODE OF Startup and Reset must be carried out after a long power cut or at first time use A Startu
Download Pdf Manuals
Related Search