AB.VR8-User Guide 036
Contents
1. NOTE PLEASE TICK ZONES INCLUDED IN PART SET ZONE PART SET AREA PROTECTED ZONE2. USER GUIDE SUMMARY OOOO Gun 09009 PART Enter Your Code Press Full or Part Press Omit Press Zone Nurrber s Press Prog 09009 0000 FULL or PARTO Enter Your Code Press Reset Enter Your Code Press Chime Press Zone Numbers Press Prog Enter Your Code Press Chime Press Reset Enter Existing Code Enter 00 Enter 01 Enter New Code Press Prog Press Reset 09000 OJO OJO DODO RESET Enter Your Code Enter 00 Enter 06 Conduct Walk Test Press Reset Press Reset 00009 OJO OJO Conduct Walk Test Enter Your Code Enter 00 Enter 05 Press 4 3 2 1 in tum Press O Press Reset USER GUIDE Ensure all zones are dosed e g windows and doors Enter your code 000 The Unset light will flash Press FULL The ext tone will sound Leave the premises During the last three seconds of the exit period the extemal strobe will flash When the system has set the exit tone and strobe will stop Ensure all zones in the Part Set area are dosed Enter your code 4000 The Unset light will flash Press PART The quiet exit tone will sound Leave the protected area VWhen the system has set the quiet exit tone will stop Note After entering your code the Unset light will flash indicating the control panel is ready to accept a command e g or PART If no valid command is entered the system will revert to unset after 16 seconds Enter via a
3. designated entry route The slow entry tone will start Enter your code 2 2 The system will unset and the entry tone will stop Note During the last ten seconds of the entry period the entry tone will change from slow to fast It is possible to omit exclude or include individual zones during setting Enter your code Press FULL or PART Press HN The exit tone and exit timer will stop and the display will illuminate the zones that are about to be armed Press the appropriate numbered button s of the zone s to be onitied or inciuciecL Press PROG to terminate the omitting procedure The system will revert to ext mode The exit tone and ext timer will restart To silence the alarm enter your code 2000 The internal and extemal sounders will stop but the extemal strobe will continue to flash The display will flash the zone light of the zone which first caused the alanm activation and illuminate the zone lights of all subsequently opened zones To cancel the display and stop the extemal strobe press RESET After an alarm activation the intemal and extemal sounders will stop after a pre set time The system will re anm but the extemal strobe will continue to flash Enter via a designated entry route The slow entry tone will start Enter your code 2 The system will unset and the entry tone will stop The display will flash the zone light of the zone which first caused the alarm ac
4. RESET All the zone lights will illuminate Press RESET again The system will retum to unset and all the zone lights will tum off Enter your code 2 0 0 Press FULL or PART The system will sound a repeating series of 10 bleeps Press 6w The display will illuminate the zones that are about to be set Press 0 The Power light will tum off Press PROG The exit tone and exit timer will start Note If any zones are left open or are in fault the display will illuminate the zone light of any open zone e g an open door and sound a repeating series of bleeps corresponding to the open zone number i e Zone 1 bleeps once Zone 2 bleeps twice etc If more than one zone is open the bleeps will correspond to the highest zone number i e if Zone 2 and Zone 6 are open the control panel will bleep 6 times While one or more zones are open the exit timer is suspended Open zones that will be closed during ext e g exit zones may be disregarded Other open zones should be closed The exit tone and exit timer will resume when all Zones are closed If it is desired to leave a zone open then it must be omitted see To OMIT ZONES during setting If an open zone cannot be closed it may be in fault If the fault cannot be corrected contact your alarm company INSTALLATION DETAILS to be completed by the Engineer Installation Engineer Installation Company Telephone Installation Date
5. ight will flash Enter 0 All the zone lights will illuminate Enter OG Initially all the zone lights will tum off and the control panel will sound the exit tone When any zone is opened the control panel will illuminate the corresponding zone light The control panel will in addition sound a repeating series of bleeps corresponding to the open zone number i e Zone 1 bleeps once Zone 2 bleeps twice etc If more than one zone is open the bleeps will correspond to the highest zone number e g if Zone 2 and Zone 6 are open the control panel will bleep 6 times Conduct a Welk Test by triggering each of the systenTs detection devices in tum and check that the control panel registers the corresponding zone as open To tenminate Walk Test press RESET All the zone lights will illuminate Press RESET again The system will retum to unset and all the zone lights will tum off The control panel has a test facility to check the operation of the internal sounder the external sounder and the strobe Enter your code 0000 The Unset light will flash Enter All the zone lights will iluminate Enter All the zone lights will tum off Press 4 to tum on the intemal sounder at high level Press 3 to tum on the intemal sounder at low level Press 2 to tum on the strobe Press 1 to tum on the extemal sounder Press 0 to tum off all the above Note The zone light corresponding to the number pressed will illuminate Press
6. tivation and illuminate the zone lights of all subsequently opened zones To cancel the display and stop the extemal strobe press RESET When the system is unset it is possible to set one or more zones to chime When a zone is set to Chime the control panel will emit a tone whenever the zone is entered To program individual Zones to chine enter your code DD The Unset light will flash pres The display will illuminate the zones that are already set to Chine Press the appropriate numbered buttor s of the individual zone s to be induded or excluded Press PROG The system will emit the chime tone to confirm that Chime has been programmed Enter your code 2 O The Unset light will flash Press I Press RESET The system will emit a tone to confirm that Chime has been canceled Enter your existing code 2 Q The Unset light will flash Enter All the zone lights will illuminate Enter Q All the zone lights will tum off Enter your new four digit code 2 2 Zone lights 1 2 3 and 4 will illuminate in sequence as each digit of the new code is entered Press PROG The system will chime to confirm the new code has been accepted and all the zone lights will illuminate Press RESET The system will retum to unset and all the zone lights will tum off The control panel has a Walk Test facility to check the operation of the systems detection devices Enter your code 2000 The Unset l
Download Pdf Manuals
Related Search