Magnum 200X Two-Port Repeaters Installation and User Guide
Contents
1. The Magnum RPM TP card supports Ethernet twisted pair segments of any standard length It is equipped with a single RJ 45 connector The RJ 45 connector is Eee ee aS en pee EE ge Sa ee ee ee TS e 2 e crossover cable With the switch in o aw the UP or LEFT position the RPM P O LINK Partition Receive connections i e a connection to another repeater or hub typically Magnum RPM TP TP port is used for up link When used for segments going to workstations and other user device connections the switch should be in the DOWN or RIGHT position The LINK LED is particularly useful in choosing the proper position for the up link switch If the LINK LED is illuminated the switch is set properly If not change the switch setting The RPM TP will support 10BASE T unshielded twisted pair wiring UTP environments with maximum segment distances up to 100m 325 ft or shielded twisted pair wiring STP of 150m 500 ft This module is designed with internal transceiver functionality In addition to PART and RX same as RPM BNC Section 2 3 1 the RPM TP has a LINK LED to indicate proper connectivity with the remote device Important Note For the RPM TP MDI X Crossover Switch DOWN or Right for_workstations and user connections UP or Left for Up Link connections to other hubs etc The RJ 45 pins normally TP crossover switch DOWN or RIGHT are per the standard for hub to user twisted pair wiring 1 rec2. 47823 Westinghouse Drive Fremont CA 94539 Attn Customer Service Appendix A Warranty Information Garrett Communications warrants its products to be free from defects in materials and workmanship for a period of three 3 years from the date of shipment by Garrett Communications During this warranty period Garrett Communications will repair or at its option replace components in the products that prove to be defective at no charge other than shipping and handling provided that the product is returned pre paid to Garrett B1 0 SPECIFICATIONS FOR MAGNUM 210X TWO PORT REPEATERS Power Supply Internal 48 VDC Option DC Power Connector 3 terminals GND Input Voltage 36 70 VDC auto ranging Power Consumption Model 210X 8 watt typical 15 watts max With the exception of the power supply all specifications and functions of Magnum 210X 48VDC models are identical to Magnum 200X listed in the main manual B2 0 48V DC POWER OPTION THEORY OF OPERATION The 48VDC power option is designed using diodes inside on each DC power input line behind the two external power connection terminals so that the power from an external source can only flow into the POWER SWITCH REPEATER repeater This allows the repeater to operate ie only whenever DC power is correctly A applied to the two inputs It protects the on GND repeater from incorrect DC input connections An incorrect polarity connection for example
3. will neither effect the repeater nor its power supply internally nor will it blow the fuse in the internal power supply B3 0 APPLICATIONS Magnum 210X repeaters are easily installed in a variety of applications where 48 VDC power is used as the primary power source The 48 VDC power configuration provides an Ethernet networking solution utilizing a special power supply in hubs with a proven track record The solution is particularly useful in the telecommunication industry where it is common for facilities to operate on 48VDC power Such companies include regular and d a 4 ae ig a od aie 4 4 GND 36 75VI This section describes the installation of the 48 VDC power source leads to the 48 VDC power terminal block on the Magnum 210Xs see figure below Figure B4 1 48 VDC Terminal Block on Magnum 210X 48VDC e a AAAA ArT T ao The 48 VDC terminal block on the Magnum 210Xs is located on the front of the unit and is equipped with three 3 screw down lead 36 70VDC posts The leads are identified as negative positive and chassis ground GND The actual connection procedure is very straightforward Simply connect the leads to the Magnum unit beginning with ground Ensure that each lead is securely tightened B4 1 UL Requirements 1 Minimum 14 AWG cable for connection to a Centralized DC power source 2 Fastening torque of the lugs on the terminal block 9 inch pound max 3 Centra
4. 10BASE FL is used for a fiber 3 Connect the Transmit TX port light colored post on the Magnum RPM FST to the Receive RX port of the remote device Begin with the color coded strand of the cable for this first TX to RX connection 4 Connect the Receive RX port dark colored post on the RPM FST to the Transmit TX port of the remote device Use the non color coded fiber strand for this 5 The LINK LED on the front of the RPM FST will illuminate when a proper connection has been established at both ends and when power is ON in the unit If LINK is not lit after cable connection the normal cause is improper cable polarity Swap the fiber cables at the Port Module connector to remedy this situation 3 3 6 Connecting Fiber Optic SC type Snap on The same five step procedure as for fiber ST type applies to FOIRL and 10BASE FL applications using an RPM FSC card used with SC type fiber connectors Follow the five steps as described in the paragraph above When connecting fiber media to SC connectors simply snap on the square male connector into the female SC jack of the device until it clicks and secures 3 3 7 Connecting Single Mode Fiber Optic SMF When using the RPM SMF be sure to use single mode fiber cable Single mode fiber cable has a smaller diameter than multi mode Fiber cable 2 15 8 60 microns for single mode 50 125 or 62 5 125 microns for multi mode where xx xx are the diameters of the core and the core plus t
5. parallel to the bottom of the 200X with the RPM media connector Media gt Connector facing the front of the unit and the RPM f Eight 8 Pin PM connector pins facing to the right Secure PM Retaining Connector _ Screw Hole the RPM using the two retaining screws Next align the RPM pins and the RPM Side view of RPM card cable connector and gently push the cable AC power connector connector onto the connector pins Chassis Cover Replacement Replace cover on chassis and secure with the four screws RPM ribbon cables Top view of 200X Insertion of RPM cards This section describes the functionality and operation of the Magnum 200X Two Port repeaters 4 1 Repeater Functionality The Magnum 200X units operate as mixed media or homogeneous Ethernet repeaters Both types are compliant with IEEE 802 3 specifications and supports all IEEE defined media including 10BASE T 1OBASE FL FOIRL 1OBASE2 and 1OBASES The following describes the basic functionality of the Magnum 200X Two Port Repeaters 1 Repeater Functions Each RPM port operates in conjunction with the controller functions of the Magnum 200X base unit functioning together as a fully compliant Ethernet repeater Each 200X unit counts as a single repeater 2 Collisions When a collision is detected at a port other than the original receiving port it generates a jam pattern to the other ports When a collision signal is detected at a receiving
6. with slide lock RPM FST Multi mode fiber 1OBASE FL ST dual twist lock connector AAMOICNE LeMperature 34 tO 120 P WU lO SU LU Storage Temperature 5 to 140 F 20 to 60 C Ambient Relative Humidity 10 to 95 non condensing Packaging 200X Enclosure High strength steel Suitable for wiring closet shelf or desktop mounting Rack mount brackets are available as an option Repeater Port Module Slots 2 Dimensions 5 4 in D x 8 5 in W x 1 75 in H 13 7 cm x 21 6 cm x 4 45 cm Weight 2 5 lbs 1 1 Kg Port Slot Cut out 2 2 in x 75 in 5 6 cm x 1 9 cm Cooling method Convection Magnum 200X Power Supply Internal AC Power Connector IEC type male recessed rear of chassis Input Voltage 90 to 260 vac auto ranging Input Frequency 47 to 63 Hz auto ranging Power Consumption 15 watts max for the 200X Repeater unit LED Indicators on Chassis 200X PWR Power Green LED steady ON indicates there is AC power RX Receive Green LED blinks to indicate network activity data being received from any of the RPMs JAB Jabber Amber LED illuminates when jabber condition illegal Sree CAA PEN OL ORE Ee PORES CN SE NOT LER SRE SCL NS EE ES Le MNT Ce ane Ree ae TASER USA 1 2 yes 2 0km 1 3 Warranty Three years return to factory Made in Specifications Repeater Port Modules RPMs RPM Type BNC AUI DTE Fiber mm Fiber sgl m TP Front Access yes yes yes yes yes yes Connector
7. Corporate Headquarters GarrettCom Inc 47823 WestingHouse Drive Fremont CA 94539 Phone 510 438 9071 FAX 510 438 9072 WWW http www garreticom com email support garrettcom com eo GarrettGom Industrial Networking at Its Best GARRETT Magnum 200X Two Port Repeaters Magnum 20X Two Port Repeater Installation and User Guide GARRETT Magnum 200X Two Port Repeaters Installation and User Guide 04 99 Magnum 200X Two Port Repeaters Installation and User Guide Part 84 00022 R04 99 Trademarks Ethernet is a trademark of Xerox Corporation Velcro is a trademark of Velcro U S A UL is a registered trademark of Underwriters Laboratories Magnum is a trademark and Personal Hub is a registered trademark of Garrett Communications Inc Important Magnum 200X Two Port Repeaters contain no user serviceable parts Attempted service by unauthorized personnel shall render any and all warranties null and void If problems are experienced with a Magnum 200X consult Section 5 Troubleshooting of this User Guide 1999 Garrett Communications Inc All rights reserved No part of this publication may be reproduced without prior written permission from Garrett Communications Inc Printed in the United States of America GARRET ee Magnum 200X Two Port Repeaters Installation and User Guide 04 99 Contacting Garrett Communications Please use the mailing address phone and fax numbers a
8. PM SMF includes full transceiver functionality and does not F o a e require an external transceiver device g full repeater to support single mode fiber 1S only to be placed across pins gt amp O Uthers are not used JUMPER ACROSS DISTANCES SUPPORTED 1 2 0 10km 3 4 not used 5 6 not used Ji DEFAULT Note Be sure to use single mode fiber optic cable with this module Single mode fiber has a smaller diameter than multi mode fiber 2 15 8 60 microns for single mode 50 125 or 62 5 125 microns for multi mode where xx xx are the diameters of the core and the core plus the cladding respectively 2 3 7 RPM DTE The Magnum RPM DTE is a module Standard 15 pin y male AUI equipped with a 15 pin male DTE connector Q Partition LED 77 _ with lock posts The RPM DTE is a mating Receive LED connector for the RPM AUI which has a 15 pin female connector and slide locks The pin i e LS assignments of the two are the same The i Yo RPM DTE card is designed to support direct Magnum RPM DTE connections no transceiver required using AUI drop cables to any device that is equipped with an AUI port Examples of such devices include servers routers bridges hubs and UNIX workstations Users may expand network distances while retaining the media of choice with these models Six Models for Mixed Media Since the Magnum 200X port connectors are modules the units are ideal when different media
9. RODUCTS DESIG NED AND MANUFACTURED IN THE USA OVERVIEW Garrett Communications offers the Magnum line of Ethernet LAN connectivity products with industry standard functionality Magnum products are available worldwide through OEMs network integrators representatives and international distributors Fiber Switches 10 100 Quad Series Mixed Media 8 amp 16 ports Dual Speed 8 port 16 port Stackables 10 100 auto sensing port Fiber Hubs Dual speed Mixed Media for fiber to the desktop Stackable Hubs SNMP Optional 10Mb series and 100Mb series both w optional port modules Switching Hubs unmanaged 500 series and managed 10Mb 5000s Two Port Switches 100Mb RJ 45 port 10 100Mb port or FDX fiber port Workgroup Hubs 10Mb series and 100Mb series both w optional port modules Personal Hubs 100Mb series 8 port dualspeed 6 port 100 with one switched 10 100Mb Personal Hubs 10Mb series 8 port AUI stackable to 5 high optional BNC or fiber port 8 or 9 port and 4 or 5 Port Personal Hubs w man up link sw Media Converters including multi mode and single mode fiber 10 Mb all media combinations incl Fiber twisted pair BNC 100Mb all fiber port types incl SC ST MTRJ VF45 FX SX The X line of configurable MiXed Media 10Mb products Stackable Concentrators SNMP optional 13 Ports Mini Concentrators 7 Ports Repeaters 2 Ports Repeater Port Modules RPMs 6 types for Ethernet media Bridge Port Modules BPMs 4 t
10. Type BNC f DB 15 f DB 15m Fiber ST Fiber ST RJ 45 Partition PART LED yes yes yes yes yes yes Receive RX LED yes yes yes yes yes yes LINK LED n a n a n a yes yes yes Switch on Face Plate yes n a n a n a n a Fiber mm is multi mode cable normally used for 10BASE FL installations up to Fiber sgl m is single mode cable used for distant installations up to 10 0Km The RJ 45 connector is shielded it accepts RJ 45 eight pin plugs for unshielded and shielded twisted pair wiring Internal termination switch for BNC no T connector is required MDI X Media Dependent Interface Crossover switch for RJ 45 uplink no crossover cable is required Ordering Information Magnum 200X TT 2 TP ports Magnum 200X BF 1 BNC and 1 fiber port Magnum 200X AF 1 AUI and 1 fiber port Magnum 200X TF 1 TP and 1 fiber port Magnum 200X FF 2 fiber ports Magnum 200X Spare Parts Magnum 200X Base chassis with 2 RPM slots internal auto ranging P S Magnum RPM BNC Module with 1 BNC connector internal term sw uses Islot Magnum RPM TP Module with 1 RJ 45 connector up link sw uses 1 slot Magnum RPM AUI Module with 1 AUI connector with slide locks uses 1 slot Magnum RPM DTE Module with 1 DTE connector with lock posts uses 1 slot Magnum RPM FST Module with 1 Fiber ST dual connector uses 1 slot Magnum RPM FSM Module with Fiber SMA dual connector uses slot Note All RPMs are interchangeable for use with othe
11. ansceiver the maximum AUI segment length is reduced According to Ethernet standards the maximum distance from the transceiver AUI connector and the attached device Magnum RPM AUJ is 50m 165 ft The AUI segment maximum length is reduced in cascaded configurations See the following note Important Note The maximum transmission distance is decreased by 6m 20 ft for every additional level of network transceiver device dropped or cascaded from the original backbone transceiver tap Voltage Common 15 Control Out Circuit B Control Out Circuit A SHELL Protective Ground Control Out Circuit Shield conductive shell Control In Circuit B oman a NOTES 1 Voltage Plus pin 13 and Voltage Common pin 6 use a single twisted pair in the AUI cable 2 Pins 4 8 11 and 14 may be connected to pin 1 2 3 4 RPM FST Fiber ST Twist lock Connector The Magnum RPM FST is a multi 10BASE FL FOIRL ST Connectors mode fiber optic module equipped with a dual ST F4 type connector It functions as an IEEE 802 3 full repeater to support 10BASE FL and FOIRL network segments When used for 10BASE FL RQ y l ae n O segments this module supports fiber optic og transmission distances up to 2000m For FOIRL 7 O LINK Partition Receive applications it supports fiber segments of up to 1000m in length The RPM FST includes full Magnum RPM FST transceiver functionality and does not require an external transceiv
12. be accompanied by a Return Material Authorization RMA number To obtain an RMA number contact Garrett Communications Customer Support at 510 438 9071 office hours 8AM 5PM Pacific Standard Time or email on the Internet to support garrettcom com When calling please have the following information readily available Name and phone number of your contact person Your Company Name Shipping Address Product Name Serial Number or Invoice Number Packing List Number or Sales Order Number Date of installation Failure symptoms including a description of the specific problem Garrett Communications will carefully test and evaluate all returned product If the problem or condition cannot be duplicated the unit will be returned as Should you need to ship the unit back to Garrett Communications please follow the these instructions 1 Package the unit carefully It is recommended that you use the original container Units should be wrapped in a bubble wrap plastic sheet or bag Retain all of your cables and connectors and this Installation Guide CAUTION Do not pack the unit in Styrofoam popcorn type packing material This material may cause electro static shock damage to the unit 2 Clearly mark the Return Material Authorization RMA number on the outside of the shipping container 3 Ship freight prepaid Garrett is not responsible for return shipping charges 4 Ship the package to GarrettCom Inc
13. ctor on the RPM AUI port 1 Plug the male end of the cable into the female AUI connector on the RPM AUI card 2 Engage the AUI connector slide lock to insure maximum connectivity 3 Connect the opposite end of the cable into a network AUI port This could bea network backbone transceiver a hub or fan out with an AUI backbone port or an AUI module in a concentrator The Magnum RPM AUI card may also used for connecting to other Ethernet devices using standard AUI cabling In this type of situation it is important to consider the AUI segment length to the attached device including any cascading See Section 2 2 3 for detailed information on the RPM AUI card connector pins and cable lengths 3 3 4 Connecting Drop Cable 10BASE5 DTE Using the steps below as a guide attach the 10BASE5 drop cable directly to the DTE connector on the RPM DTE port 1 Plug the female end of the cable into the male DTE connector on the RPM DTE card 2 Engage the AUI connector slide lock on the cable to insure maximum connectivity 3 Connect the opposite end of the cable into a network AUI port This could be a server router bridge hub or UNIX workstation 3 3 5 Connecting Fiber Optic 1OBASE FL and FOIRL ST type Twist Lock The following procedure applies to FOIRL and 1OBASE FL applications using an RPM ST card with ST type fiber connectors The primary difference between FOIRL and 10BASE FL for users is the maximum distance allowed
14. eive 2 receive 3 transmit 6 transmit other pins not used When the TP crossover switch is UP or LEFT the pins of the RJ 45 port are per the standard for up links using twisted pair wiring i e the transmit and the receive pairs are exchanged 1 transmit 2 transmit 3 receive 6 receive other pins not used p a zl 2 is used to provide connectivity with a LOBASES ThickNet backbone or to any AUI segments A transceiver is required when connecting to a Magnum RPM AUI ThickNet segment and the RPM AUI supports this convention The RPM AULI is also a universal Ethernet media interface as it may be used with a variety of different mini transceivers to provide connectivity to any media type The RPM AUI card is equipped with Partition PART and Receive RX LEDs which function the same as the identical LEDs on the RPM BNC Section 2 3 1 above The Magnum RPM AUI card is also used for connecting Ethernet devices using standard AUI cabling In this situation it is important to consider the AUI segment length or distance to the attached device The maximum transmission distance between a backbone transceiver equipped with an AUI connector and the Magnum RPM AUI card will vary When an AUI cable is used to connect the Magnum RPM AUI directly to a backbone transceiver the maximum AUI segment length is allowed If the Magnum RPM AUI is connected to a transceiver that has been cascaded from another tr
15. er device In addition to Partition PART and Receive RX LEDs a LINK LED indicates connectivity NOTE The RPM FST circuit board contains a six pin jumper which controls the intensity of the transmitted signal By default the jumper is placed across pins 1 amp 2 The jumper may be set as follows to accommodate distances of up to 4 km See Figure and Table on following page When distances of less than 2 km are needed the jumper xt J1 should be placed across pins 1 and 2 When fiber cable distances of more than 2 km are selected the minimum cable length must also be increased as shown in the table above 2 3 5 RPM FSC Fiber SC Snap in Connector The Magnum RPM FSC is also a multi mode fiber optic repeater module similar to the RPM FST It has the same LEDs indicating port 10BASE FL FOIRL SC Connectors partitioned PART receive activity RX and link operational LINK It has the same jumper settings for extra distance in certain circumstances While the functionality of the these two modules is the same the RPM FSC is equipped with an SC type snap in connector instead of an ST type twist lock connector Magnum RPM FSC 2 3 6 RPM SMF Single mode Fiber The Magnum RPM SMF is a single mode fiber optic module equipped with a dual ST type connector It functions as a Single mode ST Connectors networks The RPM SMF supports fiber Fa optic transmission distances of up to 10 Km The R
16. he cladding respectively Because of this single mode fiber allows full bandwidth at longer distances and may be used to connect nodes up to 10 Km apart The same five step procedure for multi mode fiber ST type applies to single all required RPM modules and media connectors installed There may be cases where a different RPM connector is desired making it necessary to exchange one RPM type for another The replacement procedures described inthe next two sections should only be performed by a trained technician 3 4 1 Exchanging RPMs in the Magnum 200X STOP Be sure the power cord is unplugged from the chassis before attempting to remove and or replace an PM card Failure to do so may result in damage to the unit and will void the warranty Recessed screw holes 1 Chassis Cover Removal Remove the four screws located on the sides of the unit two per side Once removed the chassis cover is easily lifted off the chassis Screw holes gt base and the interior of the Removal of Magnum 200X chassis cover unit is exposed AC power connector 2 RPM Cable Disconnection pee te ee he di eae __ Coase Each RPM is secured to the front of the 200X chassis with two screws Once these RPM retaining screws screws have been removed the RPM can be Retaining screw removal easily lifted out of the unit PM Retaining RPM Card Installation Screw Hole PM Mounting Plate Hold the card
17. ional condition and traffic activity of the unit and its associated RPM ports Magnum 200X chassis unit LED Description PWR Illuminates GREEN to indicate that the unit is receiving power RX GREEN ON when data is being received on one or more RPM ports COL Flashes YELLOW to indicate a collision has occurred JAB Illuminates AMBER to indicate a jabber condition has occurred In addition to the chassis LEDs of the 200X each RPM card features a set of status LEDs dependent on the media type supported See Section 2 2 OperalloNn IS also SMAISNUOrWarad and 1S GISCUSSEA 1n SCCUON U Should problems develop during installation or operation this section is intended to help locate identify and correct these types of problems Please follow the suggestions listed below prior to contacting your supplier However if you are unsure of the procedures described in this section or if the Magnum 200X product is not performing as expected do not attempt to repair the unit instead contact your supplier for assistance or contact Garrett Communications Customer Support 5 1 Before Calling for Assistance 1 If difficulty is encountered when installing or operating the unit refer back to the Installation Section of this manual Also check to make sure that the various components of the network are inter operable 2 Check the cables and connectors to ensure that they have been properly connected and the cables wires have not been crim
18. lized DC Power Source cable securement use at least four cable ties to secure the cable to the rack at least 4 inches apart with the first one located within 6 inches of the terminal block B5 0 OPERATION Operation of the Magnum 210Xs with the optional 48VDC power supply is identical to that of the standard AC powered models B6 0 ORDERING INFORMATION
19. m 200X extend segments of same media type Since the Magnum 200X connectors are modules the units are ideal when different media types need to be brought together at a repeater unit As media type preferences change over time and as networks expand to new distances with system growth the requirement to convert media types while ensuring standard signals on both network segments is increasingly common The Magnum 200X meet this requirement with all media combination types available Magnum 200X convenience outlet for a simple installation For rack mounting two 200X units fit side by side in a standard rack width space Rack mounting brackets for 200Xs may be optionally purchased see the Magnum Spare Parts Price List The same brackets fit the Magnum 200X Repeaters and the Model 1008 Workgroup Hubs The Magnum 200X units are suitable when network segment extensions are needed in offices labs hallways and storage areas 3 1 Locating the Magnum 200X Two Port Repeater The location of the Magnum 200X Two Port Repeater is dependent on the physical layout of the network and the area to be served The unit should be set up in a location that will accommodate easy and equal access to planned network devices and or segment connections Locate an AC receptacle that is within six feet 2 meters of the intended Magnum 200X repeater site The rugged steel case of the Magnum 200X will protect it from accidental damage in a wiring close
20. nd Internet address listed below GarrettCom Inc 47823 Westinghouse Drive Fremont CA 94539 Phone 510 438 9071 Fax 510 438 9072 WWW http www garrettcom com email support garrettcom com Federal Communications Commission Radio Frequency Interference Statement This equipment generates uses and can radiate frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio communication It has been tested and found to comply with the limits for a Class A computing device in accordance with the specifications in Subpart J of Part 15 of FCC rules which are designed to provide reasonable protection against such interference when operated in a commercial environment Operation of this equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures may be required to correct the interference GARRETT ee Magnum 200X Two Port Repeaters Installation and User Guide 04 99 TABLE OF CONTENTS PAGE LO SPECIFICATIONS eta eea aR eE E e AEA a TAE Ee ate soesesteuncoetuesegaetueseetesczensauutoetie 1 1 1 Technical Specifications isisisi isisisi iian T na 1 2 Specifications Repeater Port Module RPM 1 3 Ordering Information innon oa esa ern g asiain 2 0 INTRODUCTION sscscicsedssaenes seccs decteeds esescunanosausonte ventend ade cbs dqosuessuea
21. ndividual port LEDs are front mounted No rear access is required except for the AC power cord The internal power supply is auto ranging to handle any AC power type worldwide Power input may range from 90 to 260 vac with a frequency rating of 47 to 63 Hz The unit is equipped with a rear mounted IEC type recessed male AC power connector When shipped for use in areas other than 115 vac a power cord will not be included The 200X unit is convection cooled for silent operation The Magnum 200X base unit features Power PWR Receive RX Collision COL and Jabber JAB LED status indicators located in the front of the unit These LEDs provide a visual assessment of the operational condition and aggregate network activity at the unit and are in addition to the LEDs on each individual RPM 2 3 Magnum 200X Repeater Port Modules RPMs For standard 200X models there is an option of four different Repeater Port H o d we k e e e B a e i e e e e Magnum RPM Cards RPM BNC RPM AUI RPM DTE RPM FST RPM FSC RPM TP Each of the individual RPMs are described in detail in this section NOTE Due to the larger physical size of the Magnum Bridge Port Modules BPMs the standard Magnum 200X cannot be configured with a BPM A physically larger 200X chassis is available by special order As an alternative the Magnum 30X Workgroup Bridge is available in five standard configurations for bridge isolating a
22. ped or in some way impaired during installation About 90 of network downtime can be attributed to wiring and connector problems 3 Make sure that the power cord is properly attached to each unit Be certain that the AC power cord is plugged into a functioning electrical outlet Use the PWR LEDs to verify the unit is receiving proper power 4 If the problem is isolated to a network device other than the Magnum 200X product it is recommended that the problem device is replaced with a known good device Verify whether or not the problem is corrected 5 If the problem continues after completing Step 4 above contact your supplier from whom you purchased the product for assistance or Garrett Communications y N 5 3 c The components involved in the problem d Any particular application that when used appears to create the problem An accurate list of Garrett Communications equipment model s with serial number s Include the date that you purchased the equipment It is useful to include other network equipment models and related hardware including personal computers workstations terminals and printers as well as the various network media being used A record of changes that have been made to your network configuration prior to the occurrence of the problem Changes to system administration procedures should all be noted in this record Return Material Authorization RMA Procedure All returns for repair must
23. port it generates a jam pattern to the other port The sequence of jam signals depends on the sequence and location of collisions 3 Partitioning and Re connection A Magnum 200X will automatically disconnect partition any segment port when 64 consecutive collisions occur or after 6 5 ms of continuous transmissions Network integrity is checked every 800 ms and segment port reconnection occurs after a 512 bit packet is transmitted without error 4 Link Status The Magnum 200X RPMs indicate link integrity for fiber optic and twisted pair segments Broken cables or a loss of power at any point in twisted pair and fiber segments will turn off the LINK LED indicator on the associated RPM DELWEEH ti ANU OD TIL du Will COMNSUINE HO TMIOLle Waun d IMANAN OL 19 Wwa Le POWELL connector is located on the back of the unit In order to power down the unit simply unplug the power cable from either the wall socket power strip or the power connector on the back of the unit When connecting various Ethernet media there is no need to power down the unit Individual segments of any media type can be connected or disconnected from RPMs without concern for AC power related problems or damage to the unit 4 4 Chassis LEDs The Magnum 200X is equipped with four LEDs located on the front of the chassis unit These LEDs include Power PWR Receive RX Collision COL and Jabber JAB They are used to provide visual indication about the operat
24. pport connections to all standard Ethernet media types Each Magnum 200X unit is a complete operational unit with internal power supply all enclosed in a compact rugged steel enclosure The media connectors and the chassis status LEDs are all conveniently accessed from the front The unit is easily installed and is suitable for wiring closet shelf vertical wall or desktop mounting Magnum 200X Two Port Repeaters provide full repeater functionality per IEEE 802 3 specifications and in compliance with Ethernet V1 0 2 0 standards Magnum 200Xs operate as homogeneous media repeaters two segments of the same media type connected or as mixed media repeaters two segments of different media type connected Using two RPMs two full length segments of all media types are supported by each 200X model and configuration The family of Magnum 200X Two Port Repeater models supports all Se ee ere ee ee ee Re ee ee ee eee ge ee See er ree ee ree ge eee ee ae re ee ee a ee eee ete age ye connectivity The individual RPMs are used for one Ethernet segment each and provide full IEEE 802 3 repeater functionality supporting a full length segment Individual RPMs are equipped with a single media interface connector Any RPM can be installed in either slot of the Magnum 200X chassis Figure 2 2 1 Magnum 200X To simplify media connections each media interface port is accessible from the front of the unit All LEDs common to the 200X unit and all i
25. r Magnum X Line products and for bonus port configuration of Magnum Stackable and Workgroup Hubs Garrett Communications reserves the right to change specifications performance characteristics and or model offerings without notice 2 0 INTRODUCTION 2 1 Inspecting the Package and Product Examine the shipping container for obvious damage prior to installing this product notify the carrier of any damage which you believe occurred during shipment or delivery Inspect the contents of this package for any signs of damage and ensure that the items listed below are included Remove the items from the shipping container Be sure to keep the shipping container should you need to ship the unit at a later date To validate the product warranty please complete and return the enclosed Product Registration Card to Garrett Communications as soon as possible In the event there are items missing or damaged contact the party from whom you purchased the product If the unit needs to be returned please use the original shipping container if possible Refer to Section 5 Troubleshooting for specific return procedures 2 2 Product Description the Magnum 200X offers models of two port repeaters Magnum 200X Two Port Repeaters expand a network by extending individual Ethernet segments Where standard distance limits are not sufficient and where different media types need to come together in one Ethernet link Magnum 200X Repeaters are ideal They su
26. rop Cable 1OBASES DTE 18 3 3 5 6 Connecting Fiber Optic ST and SC types occ eeeeseeeeeeeneens 18 3 3 7 Connecting Single Mode Fiber Optic SMF cececeseeseeseeeereeeeeeeseneens 19 S A Exchanging RPMS oi ssssscsascsssaveedesseesssiceres sasotdervensvsucessousstversds coos rri N Resit 20 3 4 1 Exchanging RPMs in the Magnum 200X o 0 ec cceceecceesseescneeseeeeeeeeesaeneens 20 AO OPERA TION presero eree a aere Ee ATEA ESE EEE EOAR E ORERE Eeee 22 41 Repeater Functionality isas scscicesids a E casita i aia iie 22 4 2 Powering the Magnum 200X sss iaiiiisesie iieii isasisesisiia eaor iorenish iisi ioiei 23 AA Chassis D E B E A A sassesevecpeeoicossdays 23 5 0 TROUBLESHOOTING 24 5 1 Before Calling for Assistance ceseeseeecseseessesseeeseeeeseesseesceesseeasseraeeesseeaseees 25 5 2 When Calling for Assistance irs sicsssiecsecsssevsvisersoevestesusa susie coossatssaserdesrentasavesusaveresn 25 5 3 Return Material Authorization RMA Procedure ccccceeseeseesseeeeseeesseeseeesees 26 5 4 Shipping and Packaging Information cee eseeeeseeeeseeseeeeseeesseeseeetaeeesseeeeeees 26 APPENDIX A WARRANTY INFORMATION ccsscssssesseseeseseeseececesescescnsessescaeeeeecaeeeenees 27 APPENDIX B 48VDC SUPPLY ADDENDUM MODEL 210X ONLY lessees 27 CHANGES MADE IN THIS REVISION GARRETT ae Magnum 200X Two Port Repeaters Installation and User Guide 04 99 The Magnum Line ETHERNET CONNECTIVITY P
27. t or in a workplace setting Keep an open area around the unit so that convection cooling can occur while the unit is in operation 3 1 1 Magnum 200X Table Top Shelf Mounting The Magnum 200X unit has four rubber feet to provide stability while not scratching finished surfaces It is typically shelf mounted either in a wiring closet or in an open area To conserve shelf space it may be desirable to mount several units on top of each other If so this may be readily done as the Magnum 200X s steel case is strong Should vertical mounting of the unit such as on a wall surface be desired operation and cooling are not impaired but no brackets for vertical mounting are provided by Garrett Communications 3 3 Connecting Ethernet Media The Magnum 200X Two Port Repeater is specifically designed to support connections for any two Ethernet segment media types within a single unit This is accomplished by using a family of Repeater Port Modules RPMs The various media tvnes supported alono with the corresnondinse TEFE 802 3 standards and connector tvnes 3 3 1 Fiber mm FOIRL ST or SMA RPM FST RPM FSM BPM FST Fiber mm 10BASE FL STorSMA RPM FST RPM FSM BPM FST Fiber sgl m ST RPM SMF 1 mm multi mode 7 sgl m single mode not currently standardized by IEEE Connecting Twisted Pair RJ 45 Unshielded or Shielded The following procedure describes how to connect a 10BASE T twisted pair segment to the RJ 45 port on
28. tecwess shedbe cbespons sestgnenead 2 1 Inspecting the Package and Product 0 ccececsesceseeseeseeeeceeceecesceseeaeeseesecsecsecseeeeeeeee 22 Product Desctiptioi sessioissa ns RE Ekite 4 2 2 1 Magh m 200X Ch SSiS inisieer aiia 5 2 3 Magnum 200X Repeater Port Modules RPMs sesssesesessssssesrrrrerrsrsersrrrsrsrsee 6 2 3 1 RPM BNC 2 3 2 RPM TP 2 3 3 RPM AUI 2 3 4 RPM FST Fiber ST Twist lock Connector cccccccsceessessseeseeeteesseenes 10 2 3 5 RPM FSC Fiber SC Snap in Connector oo icceeceeeeeeeeeeeeeeeeeeeeeees 11 2 3 6 RPM SMF Single Mode Fiber s ssesssessssesssessssessssssssssesseserssessrsessesesese 11 2 3 7 RPM DT E ni eosi ieaie aara a SEAE E EEE NA Ea Iae 12 2 4 Features and Benefits sicsiss ccscscussavosssics ossasebdvssssbesucesesutesusdvessoossassvaves desi 13 2 5 Applications E A A T 14 3 0 INSTALLATION sssiisissiscsissscoisrisstsiseiciressssusissosossssistrsecsis 16 3 1 Locating the Magnum 200X Two Port Repeater cee eseeesseseeeteeeeneeseeees 16 3 1 1 Magnum 200X Table Top Shelf Mounting cee eeeeseeeeseeeeeeeeneens 16 3 3 Connecting Ethernet Media ees ceeseseeeeseseeseesenecseeecseeseeesseeesseeseeerseessaeeaseees 16 3 3 1 Connecting Twisted Pair RJ 45 Unshielded or Shielded c eee 17 3 3 2 Connecting ThinNet LOBASE2 BNC 0 eseceeeseeeeneeseeesseeeeesaeeeens 17 3 3 3 Connecting ThickNet LOBASES AUD cc ececeeseeseeteeseeeeceeteeeeeeeeeeaeeaes 18 3 3 4 Connecting D
29. the RPM TP The procedure is the same for both unshielded and shielded twisted pair segments l Using standard 10BASE T media insert either end of the cable with an RJ 45 plug into the RJ 45 connector of the RPM TP Note that even though the RPM TP connector is shielded either unshielded or shielded 1OBASE T cables and wiring may be used 2 3 Connect the other end of the cable to the corresponding device Use the LINK LED to ensure proper connectivity by noting that the LED will be illuminated when the unit is powered and proper connection is established If the LINK LED is not illuminated change the setting of the up link switch If this does not help ensure that the cable is connected properly and is not defective The Magnum RPM TP is equipped with a up link slide switch to accommodate repeater to repeater connections without special cross over connectors NOTE When installing a Magnum 200XX TT Workgroup Bridge the up link switches of both connectors should have the same setting both left or both right When installing a Magnum 200X with only one twisted pair port you will normally set the up link switch to the DOWN or RIGHT position however this is dependent on your network configuration see step 3 above 3 3 2 Connecting ThinNet 10BASE2 BNC III CONNCCUNS IMICKINGL LUDASEOS AUI Using the steps below as a guide attach a new or existing 10BASE5 ThickNet drop cable directly to the AUI conne
30. types need to be brought together at a repeater unit Two Port models are available with all combinations of BNC AUI TP and Fiber These mixed media models ensure standard signals and up to full length distance on each network segment accommodating changes in media preferences as networks change over time RPMs Repeater Port Modules for All Standard Ethernet Media Multiple RPMs support all of the various IEEE 802 3 standards including 10BASE FL FOIRL 1OBASE2 1OBASES and 10BASE T Fiber Ports Meet 10BASE FL Specification 2000 meters distance The Magnum X line RPMs meet the new FL specification for 2 Km distance They also support the older FOIRL specification rated at 1 Km Front Mounted Connectors and LEDs on 200X The installation of Magnum 200X units only requires front access for network connections Similarly status LEDs are all readily visible from the front for ease of monitoring operational status over time An internal universal power supply allows any Magnum 200X unit to be used throughout the world Ul HOTMOSCHCOUS TMEOld LOVPedtel MOULIS SUPVULL ACH StA CULLE Mela ty Pe dud allow users to expand network distances while retaining the wiring media of choice As many as four repeaters may be connected in series to connect users at the extremities of 5X the standard segment distance while still adhering to the Ethernet four repeater rule 10BASE2 BNC Magnum 20 Two Port Repeater Figure 2 5 1 Magnu
31. workgroup segment to improve performance LUDAODs UUAA COLIMCOLOL LIUS T e oot a RPM performs full IEEE 802 3 es i repeater functionality and is used for 10BASE2 ThinNet Magnum RPM BNC commonly referred to as BNC connections The RPM BNC module is designed with a special switch selectable internal termination function that eliminates the need for a tee connector and a 50 ohm terminator To take advantage of internal termination the slide switch should be in the DOWN or right side position In this configuration the 10BASE2 segment is directly attached to the BNC port where it is internally terminated When the switch is in the UP or left side position the BNC port requires a tee connector not supplied and a 50 ohm terminator for proper termination Certain applications may require a tee connector used as a tap to allow the 1OBASE2 coax segment to continue on past the RPM BNC connection The RPM BNC module includes one partition PART and one receive RX LED which are visible from the front The PART LED flashes AMBER to indicate that the segment has been automatically partitioned As soon as normal transmission resumes the segment will be automatically re established The RX LED illuminates GREEN intermittently to indicate data is being received Important Note For the RPM BNC Termination Switch DOWN or right Internally Terminated UP or left Requires T Connector 23 2 RPM TP Twisted Pair
32. ypes for segment isolation GARRET ae Magnum 200X Two Port Repeaters Installation and User Guide 04 99 Workgroup Bridges 10Mb series Fan Outs 10Mb series 4 and 8 Port Deluxe 2 and 4 Port Standard Models Transceivers 10Mb series Mini Transceivers and Coax Models All Types April 99 GARRETT ee SE SES RES ae NE eet Partitioning Enforced after 32 consecutive collisions Reconnect Occurs after 512 bits of error free transmission Network Standards Ethernet V 1 0 V2 0 IEEE 802 3 LOBASE T 1OBASES 1OBASE2 10BASE FL amp FOIRL and DTE The Magnum 200X Two Port Repeaters are physical layer standard Ethernet products and operate independently of all software Maximum Ethernet Segment Lengths DTE AUI Drop Cable 50 m 164 ft 10BASE T twisted pair 100 m 328 ft Shielded twisted pair 150m 492 ft 10BASE2 ThinNet BNC 185 m 607 ft 10BASE5 ThickNet 500 m 1 640 ft FOIRL multi mode Fiber optic 1 km 3 281 ft 10BASE FL multi mode Fiber optic 2 km 6 562 ft Single mode Fiber optic 10 km 32 810 ft Connectors 200X Two Magnum RPM ports on the front AC power in rear RPMs available with standard 200X models RPM TP Shielded female RJ 45 with up link switch Note Shielded 10BASE T connectors accept either unshielded or shielded wiring plugs for standard twisted pair media wiring RPM BNC ThinNet BNC connector with internal termination switch RPM AUI D Sub 15 Pin Female
Download Pdf Manuals
Related Search