Aquamaster User Guide Cover
Contents
1. Troubleshooting symptom suggested cause Hoist will not Switched off function at all Hoist lacking power Battery power Hoist cuts out while is low Lifting Hoist cuts out while Maximum load Lifting LED flashes exceeded red in sequence with 1 beep of buzzer repeated Hoist cuts out while Obstruction lowering encounted slack tape device operates Cannot dispense Insufficient tension sufficient lift tape to on lifting tape connect hoists to slack tape device track operates Motor is running but Tape is tangled hoist will not lift or inside hoist and lower may be damaged Troubleshooting continued overleaf User Guide solution Ensure red rocker switch on hoist is switched on Batteries need charging Reset hoist remove load and recharge See page 12 for charging instructions Remove excess load Reset hoist by pressing and holding reset button until 3 beeps heard Remove obstruction Pull the tape out of the case while pressing the down button on the hand control See page 8 Service call required Chiltern Invadex Portable Hoist Troubleshooting Audibleand visual signals Hoist Audible solution Visual Posts 1 Power up and self 3 Beeps no repeat Hoist OK No action test hoist reset light green required 2 Weight overload 1 beep pause Remove excess continuous weight red flashing Reset hoist with handset 3 Low main 12V Battery 3 beeps pause Return to charge cont2. Servicing and Maintenance Lifting Operations and Lifting Equipment Regulations LOLER 1998 were made under the Health and Safety at Work Act 1974 LOLER 1998 applies to any item of lifting equipment Based upon British and European Standard BS EN 10535 and Health and Safety Executive guidance Chiltern Invadex recommend that hoists are fully serviced including a load test at least every 12 months with an interim six monthly inspection to conform to LOLER 1998 requirements Refer to your supplier for alternative local regulations that may apply Chiltern Invadex Portable Hoist Using the controls Attachment Hook Room to room Transfer Hook Integral Carrying Handle Charging Socket Power on off Switch Connecting the Hand control to the Hoist Unit User Guide Three Button Hand control used on Wispa Hoist Models Dual controls The Wispa Lite Portable Hoist can be operated by the controls on the hand control or from the hoist cover Operating the controls on the hand control and hoist cover The lifting and lowering functions are controlled by the up and down buttons The reset button is used in the event of a hoist malfunction see troubleshooting guide page 15 Hand control operation Note The hand control is a sealed low voltage unit completely safe to use with wet hands 4 Lowering Lifting Operation using controls on hoist cover Charging Socket Power On Off Switch Hand Control Socket
3. This will make the first swinger tape slack as Fig 6 Detach the first swinger tape from the hoist as Fig 7 This will leave the hoist in the second room set up for standard operation as Fig 8 Chiltern Invadex Portable Hoist Charging the Wispa Lite Portable Hoists are designed to offer flexible working over a number of fixed tracks or gantry systems To ensure maximum flexibility it is VERY important to charge the hoist after use Before using the Wispa Lite Portable Hoist ensure the battery is adequately charged by charging for a minimum of 2 hours SAFETY NOTE IMPORTANT Only use the charger supplied with the Wispa Lite Portable Hoist We recommend that you leave the hoiston chargeat all times when not being used The batteries of the hoist cannot be overcharged This does not waste energy as the hoistonly takes up charge when it needs to Taking this action will prevent the early deterioration of the batteries and minimise the number of low battery warnings see below To charge the batteries 1 Plug the charger into the mains 2 Turn on the mains 3 Turn the hoist on using power on off switch see page 4 4 Connect the charged output plug into charging socket on the hoist unit Charge Indications Initially a solid red LED see page 5 indicates bulk charge This changes to a flashing green to indicate trickle charge and the hoist is available for use as
4. object for support A Trolley is available as an optional accessory for this purpose Part No OHWPTRANS 2 Pull the tape out of the case while pressing the down button on the hand control or on the hoist case Release enough tape to allow the hoist to be connected to the ring on the track without lifting the hoist Where the ceiling height is too high to allow direct attachment of the clasp to the trolley the attachment handle should be used Attach the lifting tape to the attachment handle as shown in the diagram Release enough lifting tape to allow the hook of the attachment handle to be attached to the trolley 3 Connect the hook on the lifting tape to the ring on the attachment handle 4 Attach the attachment handle hook to the full ring on the track A lanyard can also be supplied as an optional extra available in choice of lengths Please contact your nearest Chiltern Invadex Office for details User Guide NOTES When the hoist is not under load the tape will need to be pulled out of the case whilst pressing the down button on the hand control Hoists should only be used to lift vertically Lifting at an angle will wear the lifting tape prematurely The Hoist should not be used if the lifting tape is worn Lifting using the Wispa Lite Portable Ensure each sling loop is attached correctly 1 to each of the hoist s sling support arms It must be beneath the retainer to prevent the st
5. Emergency Lowering Button Chiltern Invadex Portable Hoist Emergency Stop On off switch The red power on off switch A provides an emergency cut out facility Emergency Lowering In the unlikely event of a hoist or hand control malfunction the hoist occupant may be lowered using the emergency lowering button To operate push and hold the button on the side of the case until the client is lowered safely as shown below Emergency Lowering Button User Guide Folding the sling support arms Fold the sling support arms down fully prior to connecting the sling Carry handle Carrying the hoist The arms should be folded up when carrying the hoist Adjusting the lift lower speed Using the hand control or the controls on the hoist case press and hold the reset button Press the direction arrow repeatedly until the desired speed is achieved the speed increases in increments oy Note When the buttons are released the hoist will automatically reset itself to normal speed Chiltern Invadex Portable Hoist Attaching the Wispa Portable to the Track Track full ring Attachment handle Attachment full ring handle S A Lanyard can be Attachment used when the track is Lifting P too high to tape Gn Pd reach SAFETY NOTE IMPORTANT Do not attempt to lift the Wispa Lite Portable Hoist above waist height to attach it to the track 1 Place the Wispa Lite on an
6. Overhead Hoists user guide Wispa Lite Portable Gnittern Invadex Solutions for Living Ce Overhead Hoists Eniltern Invadex Solutions for Living User Guide Contents Things to consider before using the Portable HOIST seenak 2 Using The Conto S sarnu 4 Emergency Stop Emergency Lowering 6 Folding the sling support arms 7 Adjusting the liftlower speed o o T Attaching the Portable tO the Track isssesssarsspaaecsisnizanmaa casser istisini 8 Lifting using the Portable oooo 9 Room to room transfer oooo 10 11 Charging the Portable oooooo o o 12 Servicing and Maintenance oo 13 PAS an ena akan 14 Troubleshooling iii sa 15 16 Hoist Specification oooooo 17 Wafa NY main ni aa 18 Hoist Service Record 19 20 This product has been designed to the highest standards with safety strength and quality in mind Follow the recommendations in this guide to ensure maximum benefit from your Wispa Lite Portable Hoist Should you experience any difficulties please consult the troubleshooting guide prior to contacting your Portable Hoist supplier Your Portable Hoist has been designed and tested to meet the highest standards of safety Read the safety section of this guide prior to use This is contained on page 2 Chiltern Invadex Portable Hoist Intended Use of the Pro
7. duct The Wispa Lite Portable hoist has been designed to lift and transfer a disabled person with the help of a carer It should be used in conjunction with a Wispa sling and other lifting accessories from the Chiltern Invadex range as assessed by a trained person Note Not all slings and accessories are compatible with the hoist If you are unsure please contact your nearest Chiltern Invadex Office The correct and appropriate use of this product will reduce the risks associated with manual patient handling The lifting transferring task should be assessed by a trained person Recommended working procedures Portable Hoists are designed to offer flexible working over a number of fixed tracks or gantry systems To ensure maximum flexibility the Wispa Lite should be placed on charge when not in use The Wispa Lite charger will switch itself off when the batteries are in a fully charged state The complete charging procedure is shown on page 12 Safety Considerations Before you start e Ensure that all users read this guide before operating the hoist e Do not operate the Wispa Lite Portable Hoist without training in the safe operation of the hoist and slings e Only use slings which have been assessed as suitable by a trained person e The Wispa Lite Portable Hoist should not be used if there is fraying or stitch damage to the lifting tape lanyard slings or if the hoist itself is damaged in any way e Read the relevant Sling Us
8. e Hoist Warranty Your Chiltern Invadex Portable Hoist carries a 2 year warranty from the date of purchase subject to the following 1 Should you experience any problems with our workmanship or materials within the first 2 year period please contact your point of purchase 2 Repairs made during the warranty period will be carried out free of charge provided the product has been used strictly in accordance with the guidelines set out in this user guide 3 Our warranty does not cover replacements adjustments or repairs which may be required as a result of normal wear and tear wilful or accidental damage misuse neglect or any other cause which is beyond the control of Chiltern Invadex 4 Modifications and repairs made to this product by unauthorised persons will render the warranty void 5 Only parts manufactured or approved by Chiltern Invadex shall be used to repair this product Use of unauthorised parts will invalidate all warranties and remove all liability from Chiltern Invadex for the safety of this product 6 Chiltern Invadex shall in no event be liable for any damages costs or expenses arising from any claim made under this warranty save for any legal liability of Chiltern Invadex for death or personal injury resulting from the company s negligence in respect of its products 7 This warranty does not affect your statutory consumer rights 8 The hoist being fully serviced including a load test at least
9. er Guide which is provided with each sling It explains in detail how to use slings correctly e Before using the Wispa Lite Portable Hoist for the first time ensure the batteries are fully charged e Do not exceed the Maximum load of the hoist 200kg 31 stones 440lbs When using the Wispa Portable After use User Guide Do not lower the unit into water or splash the unit as this can cause damage to the hoist Do not attempt to lift the Wispa Lite Portable Hoist above waist height to attach it to the track Hoists should only be used to lift vertically Lifting at an angle will wear the lifting tape prematurely Take care when attaching or removing a sling as the hoist could cause injury to the user if hit in the face Be aware of the potential damage to light fittings etc when using the Wispa Lite Portable Hoist and attachment hook Ensure when the hoist is in use that the surrounding area is clear and the person being lifted is clear of all obstacles Do not leave a user unattended in the sling Place the Wispa Lite Portable Hoist on charge when not in use Only use the charger supplied with the Wispa Lite Portable Hoist The outer case mechanical parts and track should only be removed by a qualified service engineer Do not touch any of the moving parts in the hoist unit or in the track Contact Chiltern Invadex for assistance Special Note Report any defects in the hoist or slings immediately
10. every 12 months by Chiltern Invadex or such other person authorised by Chiltern Invadex Please see page 13 for further details including pricing information Excludes batteries and lift tape User Guide Wispa Hoist Service Record Serviced By Company E E E E et re tres aa ACTOS SR ET RRR Bore AA ANA TAN PGN post code Engineers Name please print Signature Dale na Load Tested TO nenen ena Kgs Comments e a a a na Serviced By company menen e E A A E R EE address aan rece anatara intan eni ammnanamana nana mana aman ta datam Eee anna Sane PR Nae na an gan anne NN nan aa Rr ep postcode Engineers Name please print Signature Datos nee Eoad Tested To ereere e Kgs CommemS a a eae oe set eed ena anna naa aan aa Serviced By company orean aes Sse Anta Dada aan eaten rear ACTOS Si nan na PA aan In E Da Pan DE PI Bean kaan i nee sama saceadsaseszadessucea Mae baacdactsescegnaseterseere postcode Engineers Name please print Signature DalC eren srta Load Tested To coco Kgs Comment ee RE eS BAL Chiltern Invadex Portable Hoist 20 Serviced By company aa A aa an anne Hi address NN ES AA an Aa Di Dn Aas Po ban An na AE e postcode Engineers Name please print Signature Dat rnana Eoadilestedilo Kgs Comments a a an na aa ada na Serviced By company Ea napa Na Anna anna Pp Naela see address anna seni e cree tan orar ma
11. in anyway whatsoever without the express permission in writing of Chiltern Invadex Ltd As part of our commitment to new product development we reserve the right to alter specifications without prior notice This is an original design of Chiltern Invadex Ltd in which Design Right Subsists CINV 407 03 05 05 Published by Chiltern Invadex Ltd 6 Wedgwood Road Bicester Oxon OX26 4UL Registered in England No 1182024 In Northern Ireland Chiltern Invadex NI Ltd 5 Balloo Way Balloo Industrial Estate Bangor County Down BT19 7QZ Registered No NI 19958
12. inuous position red flashing 4 Low main 24V battery 4 beeps pause Return to charge continuous position red flashing Important To reset the hoist with the handset press and hold the red reset button on the handset until 3 beeps are heard see 1 above or press R on hoists cover User Guide Hoist Specification Weight 8kg 17lbs Lifting capacity 200kg 31 stones 440lbs Case construction Vacuum moulded Flame Retardant ABS Lifting Range 2200mm 7 2 Top of track to bottom of sling support arm No of Lifts per Charge 40 Battery voltage 24vdc Overload cut out lt 150 maximum load Hand control Low voltage hand control IP67 rated Track Aluminium extruded track coated white Low battery indication Audible and visual waming device 600mm 23 5 up and down cycle with average75kg 11 5 stones 168LB patient weight 520mm 20 5 at maximum ja height 2720mm 811 at lowest position see Fig A This range can be lowered using a lanyard see page 8 j A 2720mm 8 11 B 520mm 20 5 C 250mm 10 D 530mm 21 E 240mm 9 5 F 380mm 15 G 170mm 7 des Serial number Weights and dimensions are for guidance only CE MARK The Chiltern Invadex Wispa Portable carries the CE mark and complies with EC Directives Medical Device Directive 93 42 EEC EMC Directive 89 336 EEC Low voltage Directive 73 23 EEC 17 Chiltern Invadex Portabl
13. rap frrom coming loose as 2 below Sling straps should be attached to the hoist s sling support arms in the same order on each side to ensure the sling occupant is lifted evenly Whilst using the hoist care should be taken to ensure the body of the Wispa Lite Portable is kept at a distance from the sling occupant to avoid potential anxiety or discomfort Chiltern Invadex Portable Hoist Room to room transfer In normal operation the hoist set up should be as Fig 1 with the swinger kit not attached to the hoist room to room lug For room to room operation the swinger kit hook should be attached to the hoist room to room lug as Fig 2 The hoist should then be lowered to provide slack on the main hoist lifting tape as Fig 3 Note Press the down button on the hand control or on the hoist case until the hoist stops on its own The main lifting tape should then be detached from the trolley set in the first room and attached to the trolley set in the second room as Fig 4 Note If the tape is not long enough pull the tape out of the case while pressing the down button on the hand control or hoist case Stop when sufficient tape has been released User Guide Room to room transfer cont Using the hand control power the hoist UP as Fig 5
14. required Low Batteries If it has not been possible to keep the batteries charged a low battery is indicated by a red flashing LED and an audible warning of three or four beeps The hoist should be charged at this point If the hoist is continued to be used without being charged it ultimately will not lift or lower If necessary operate the emergency lowering procedure described on page 6 Important note If any bleeps are audible then it will be necessary to reset the hoist by pressing and holding down the red button on the hand controls or the R button on the side case until 3 bleeps are heard 12 User Guide Servicing and Maintenance Based upon EN10535 and Health and Safety Executive guidance Chiltern Invadex recommend that hoists are fully serviced including a load test at least every 12 months with an interim six monthly inspection to LOLER requirements The frequency of servicing should be increased in areas where the environment or heavy usage may cause deterioration of the equipment Further details can be obtained from any Chiltern Invadex Office shown on the back of this booklet Chiltern Invadex and its Authorised Dealers are able to carry out all aspects of servicing and maintenance work Maintenance of this equipment should only be conducted by engineers trained and certified by Chiltern Invadex Keep the service record at the back of this booklet up to date Service pricing Prices are available from Chil
15. tan mana ar aan Rana nana nona Enade ne SCARED ena nana Tenan an Abe Nana reer er postcode Engineers Name please print Signature Date ea aman Eoadilestedilo eres Kgs Comments ee na an en an en BAN en aa Serviced By Company an nan anna ae Sp Aa nana na ata anna in ACCESS E Pn Na RR Pen A ET NA AAN RAS EN ENG DEA ATA BAN BRA SA RA postcode Engineers Name please print Signature Dale eat a koadilestedo Kgs Comments ar eae an nan Please fill in the information below for future reference Dealers Name Telephone na eee eer Your Serial Number is Models covered Wispa portable OHWPL Gnittern Invadex Solutions for Living Chiltern Invadex Ltd 6 Wedgwood Road Bicester Oxfordshire OX26 4UL Tel 01869 246470 Fax 01869 247214 Web www chilterninvadex co uk E mail sales O chilterninvadex co uk Overseas Enguiries Tel 44 0 1869 365545 Fax 44 0 1869 365567 Overhead Hoists Chiltern Invadex NI Ltd 5 Balloo Way Balloo Industrial Estate Bangor County Down BT19 7QZ Tel 028 9145 0497 Fax 028 9127 0046 Chiltern Invadex Ltd Unit 16 Evans Business Centre 68 74 Queen Elizabeth Avenue Hillington Industrial Estate Glasgow G52 4NQ Tel 0141 880 9986 le BSI Fax 0141 880 9990 FM 40009 FM 21085 Copyright Chiltern Invadex Ltd The design of the product shown in this guide is vested in Chiltern Invadex Ltd and should not be copied or reproduced
16. tern Invadex Offices to secure a visit from a Chiltern Invadex Service Engineer DO NOT USE IF 1 There is any damage to the hoist 2 There is fraying or stitch damage to the lifting tape lanyards or slings General guidelines to ensure maximum cleanliness Wipe with a dry cloth track and hoist For stubborn marks use a damp cloth and a mild cleanser Always read the manufacturers instructions prior to applying the cleanser A solution of 0 1 Sodium Hypochlorite should have no adverse effects on the cleaning of the track and hoist cover Slings should be washed in accordance with the instructions on the label sewn into the sling 13 Chiltern Invadex Portable Hoist Parts item description qty part no 1 Input power lead pack c w charger UL approved 1 OHHS200 2 Attachment handle 600mm length 23 5 1 OHTRK28 200kg 31stones 450lbs max load 2 Special length attachment handle 1 OHTRK36 3 Hand control 1 300 00042 Cl 4 Lanyards 305mm 12 200kg maximum load 1 OHTRK201 5 Lanyards 457mm 18 200kg maximum load 1 OHTRK202 6 Lanyards 610mm 24 200kg maximum load 1 OHTRK203 7 Lanyards 762mm 30 200kg maximum load 1 OHTRK204 8 Lanyards 838mm 33 200kg maximum load 1 OHTRK205 9 Lanyards 915mm 36 200kg maximum load 1 OHTRK206 10 Lanyards 1220mm 48 200kg maximum load 1 OHTRK207 1 Lanyard special length 1 OHTRK208 12 Room to room Kit 1 OHHS207
Download Pdf Manuals
Related Search