Home

Socket Bluetooth Cordless Hand Scanner User's Guide

1. 3 Make sure the PDA has Bluetooth on and is in Discoverable mode i e it will be visible to other Bluetooth devices Make sure the PDA is not restricted to only connect to devices it already paired with 4 Follow the instructions for your type of Bluetooth stack to pair the CHS to your PDA 7 To determine your type of Bluetooth stack tap Start Programs SocketScan 10 Tip folder SocketScan Settings The Bluetooth stack is reported at the top of the screen CF In the device search the CHS will appear as Socket CHS xxxxxx The characters in TIP brackets are the last six characters of the CHS Bluetooth Device Address BDA which is labeled inside the battery compartment Cr Only devices running Bluetooth 2 0 will prompt for a passkey F The CHS will beep once when it has connected and is ready to scan barcodes TIP The LED will also blink blue once every 3 seconds 66 Bluetooth Connection Instructions Stack Microsoft These instructions are based on the SoMo 650 a Tap Start a Settings Connections tab Bluetooth Tap Add new device Alternatively you can tap Add at the bottom of the screen Follow the screens to pair with the CHS In the list of found devices tap Socket CHS If prompted for a passkey enter 0000 four zeroes In the Bluetooth Settings screen tap on the COM Ports tab Tap New Outgoing Port te Setting
2. The CHS has been successfully tested in SPP mode with the Microsoft Broadcom and Toshiba Bluetooth stacks CHS in SPP mode has not been tested on PCs running other Bluetooth stacks and may not work correctly zi Socket highly recommends that you use the CHS in SPP mode To learn more read our white paper http www socketmobile com pdt techbrieflsocketscan 10 sdk_white paper pdf zi CHAPTER 5 SETUP FOR WINDOWS PC 37 OPTION 1 USING THE CHS IN HID MODE To pair the CHS with your computer TIP You only need to pair the CHS with your computer the first time you try to connect 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high CF The LED blinks blue once per second to show that the Bluetooth radio is on but not TIP connected 2 Scan this barcode to configure the CHS for HID mode for peripherals Afterwards the CHS will beep 3 times FNBO001000500 FNB j IMPORTANT Print out this page to scan the barcode Do not scan it onscreen By default the CHS is in HID Keyboard mode If the CHS was changed to SPP mode TI first use the Command Barcodes to change the CHS to HID mode before scanning the barcode above 3 Turn on Bluetooth 3 on your computer Refer to your computer s documentation for Instructions 4 Use you computer s Bluetooth software to connect to the CHS see instructions on next page C7 In the device search the CHS w
3. The CHS detects an internal fault will reset and power off If connected to a host computer the scanner will disconnect during the reset Vibrate Vibrate Meaning Power on OR data successfully scanned and sent to host device F To modify the LED beep and vibrate settings you can use the Command Barcodes or if the TIP CHS supports SPP mode for your OS the Scanner Settings utility see chapter for your OS Bluetooth Mode Sequence When the CHS is powered on its Bluetooth mode will gradually change if no connection is made Time after turning on CHS Bluetooth mode 0 5 minutes Discoverable and connectable 5 20 minutes Connectable CHS automatically powers off Simultaneous Use of CHS and Socket Plug in Device with the SoMo 655 You can use the CHS and a Socket plug in barcode RFID magnetic stripe reader simultaneously with the SoMo 655 handheld computer However you will need to run two different versions of SocketScan concurrently e For the CHS use SocketScan 10 which you can download from http www socketmobile com support downloads data collection series7 ss10 e For Socket plug in devices use SocketScan 7 or older which you can download from http www socketmobile com support downloads data collection series5 CHAPTER 1 INTRODUCTION 9 2 SCANNER SETUP INSTALLING BATTERIES AND ATTACHING THE TETHER 1 Use a coin or screwdriver to unlock and remove the battery cover Turn the lock unde
4. This type of File can harm your computer Are you sured N rin you want to download SocketScanlOSetup exe 4 The installation wizard will launch Follow it to install software for BlackBerry Snckeriamn 10 Insralisticld an 5 After software installation click Finish 6 Use a USB connection cable cradle to connect the smartphone to the PC 7 Launch the BlackBerry Desktop Manager Click Start Programs BlackBerry Desktop Manager Cr Click Applications If SocketScan 10 doesn t show in the list of TIP Applications click Import files Browse to the location of the SocketScan 10 file on your computer 8 In the Application Summary pane click Apply F By default all of the SocketScan 10 subfiles will be selected for installation Do not TIP deselect any 7 SETUP FOR BLACKBERRY 83 To pair the CHS with your BlackBerry smartphone You only need to pair the CHS with your phone the first time you try to connect The following instructions are based on Socket EZ Pair a feature of SocketScan 10 Tip software For instructions on how to connect by generating and scanning a special barcode please see Appendix 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high CF The LED blinks blue once per second to show that the Bluetooth radio is on but not connected 2 Scan this barcode to change the CHS to SPP mode Afterwards the CHS will
5. British Post Canada Post Codabar lt Codablock A Codablock F ia Enabling all possible symbologies will make the decode process slightly longer TIP Weg The RSS symbology is now known as GS7 DataBar TIP Cr If you would like to read UPC A symbols be sure to disable GS1 DataBar so that TIP GS1 DataBar symbols don t get mistakenly decoded Test The Test feature reports the properties of a scanned barcode 1 In the main screen of Scanner Settings touch Menu Test Socket CHS OFSDFC Configuration Symbology 2 In the Scan Window screen select if you would like scanned data to appear as ASCII or hexadecimal format 3 Scan a barcode The Scan Window will report the barcode s symbology barcode type data length and data CHAPTER 4 SETUP FOR ANDROID 35 Language Selection To check your current language selection 1 Open an internet browser 2 Touch any input field to bring up the keyboard 3 Touch and hold the keyboard key to bring up the language selection menu ASU X Bi 3 08PM http www google com gt ana mi Change current language English t l Deutsch Fran ais Keyboard ke 123 English The screen will indicate your current language selection To change your language selection select another language and the menu will close Accented Characters in the Keyboard When using the keyboard of a language requiring accent marks such a
6. After try to connect SocketScan 10 reports the Friendly Name of the last CHS connected to the computer and I cannot modify any advanced settings or symbologies POSSIBLE REASONS SOLUTION This is a known issue in SocketScan 10 for Close and restart SocketScan 10 and reconnect Windows XP and Vista SYMPTOM The Bluetooth software indicates that the CHS has connected but when I try to scan data it does not enter into my application POSSIBLE REASONS 10 RCN ELON The CHS is in SPP mode and your PC has Use your Bluetooth utility to disable extra incoming multiple incoming Bluetooth serial ports Bluetooth serial ports In SocketScan Settings click Ports enabled to access the Bluetooth utility The CHS is in SPP mode and SocketScan 10 Start SocketScan 10 Click on the desktop shortcut icon Is not running The keyboard wedge is not enabled in Make sure Use keyboard wedge is selected SocketScan Settings The CHS is in SPP mode but not assigned to In SocketScan Settings make sure the CHS is assigned to an incoming Bluetooth serial COM port an incoming Bluetooth serial COM port If your computer has the Toshiba Bluetooth stack in SocketScan Settings click Ports Make sure the CHS is assigned to a Bluetooth port named LocalCOM Server SYMPTOM The SocketScan 10 system tray icon does not appear by default after I install the software POSSIBLE REASONS 10 RUN ELON Bluetooth was not fully initialized before Make sure
7. CHS 7E 7M 7P 7NRx 7C or 7Ci 2D Scanner models CHS 7X 7XRx 7Xi or 7XiRx _ 2D Scanner 12 If prompted select your CHS 7 SETUP FOR BLACKBERRY 85 13 After they pair and connect the CHS will beep once to confirm the connection then beep twice to signal a disconnection Click Menu Close to close Socket EZ Pair Socket EZ Pair Available scanners our scanner is now ready to connect to your device Please close this application and launch your scanning application 14 SocketScan 10 will try to connect to the CHS If asked to confirm click Yes SocketScan 10 No device connected Accept connection request from Socket CHS 0C7831 _ Don t ask this again CF The CHS will beep once when it has connected and is ready to scan barcodes The LED will also blink blue once every 3 seconds 15 The registration screen will appear Follow the instructions to register the scanner or click Cancel to register later 86 To scan barcodes 1 Open your application Place the cursor where you want to enter data 2 Press the trigger button to scan a barcode Make sure the aiming beam extends across the entire width of the barcode vain anita ec Ot For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen CF After decoding the barcode and sending it to the phone by default the CHS will Tip Deep once and vibra
8. iPad 2 iPad Android OS 2 1 and later v Android v Android 2 2 or later 2 1 or later with support for Bluetooth BlackBerry OS 5 00 714 or later for Bold 9700 other models not tested with SocketScan 10 may require previous software version BlackBerry PlayBook APPENDIX A SPECIFICATIONS 91 Symbologies Bookland EAN ISBN EAN 13 Chinese 2 of 5 Codabar including support for ISBT 128 bit concatenation Code 11 Code 128 Code 39 Trioptic Code 39 Code 39 Full ASCII Code 93 Discrete 2 of 5 GS1 DataBar RSS GS1 128 UCC 128 EAN 128 Interleaved 2 of 5 ITF 14 MSI UPC EAN JAN VIN Scanner Performance Class 2 linear laser 1D Wide default 47 3 Narrow 35 3 Rate Optical 0 004 inch 0 102 mm min barcode element width X Dimension Resolution i aa nm Decode Distance 1 5 to 45 inches 3 8 to 144 cm typical Depends on symbol density symbology W N Ratio label media and scan angle Provides tactile feedback for good read Bluetooth Characteristics Standard Default mode HID Keyboard class device 2 45 GHz ISM band supports Advanced Frequency Hopping AFH 56 bit encryption Class 1 radio Typical Output 12 dbm Bluetooth Stack Windows Mobile Microsoft Broadcom v1 8 0 6501 or v1 9 3 Support for Windows PC Microsoft Toshiba 4 00 34 5 00 6F or later Broadcom A amp Mac 5 1 0 1700 or later Bluetooth 2 1 for best results Certification Compliance Certified to I
9. ication Downloading Complete 7 Choose where you would like to install the software Tap Install Choose a location to install Socket Mobile SoecketScan 10 Device O SoMo File Store Space Needed 1684 KB Space Available 67427 KB ee q Install A 8 If prompted to soft reset tap Yes Installing SocketScanl0 CAB SocketScan 10 J soft reset is required to complete the installation Do you want to reset now P 9 After the soft reset SocketScan 10 will automatically launch Cr If SocketScan 10 reports that Bluetooth needs to be enabled turn on Bluetooth on TIP your PDA and tap Retry 6 SETUP FOR WINDOWS MOBILE 65 To pair and connect the CHS with your PDA CF You only need to pair the CHS with your PDA the first time you try to connect TIP F The following instructions are based on Socket EZ Pair a feature of SocketScan 10 TIP software For instructions on how to connect by generating and scanning a special barcode ActivePairing please see Appendix I 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high The LED blinks blue once per second to show that the Bluetooth radio is on but not TIP connected 2 Scan this barcode to change the CHS to SPP mode Afterwards the CHS will beep 3 times F NBOOF40000 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen
10. information contained in this manual Please refrain from any applications of the Socket Bluetooth Cordless Hand Scanner that are not described in this manual Please refrain from disassembling the B uetooth Cordless Hand Scanner Disassembly of this device will void the product warranty You can track new product releases software updates and technical bulletins by visiting the Socket Mobile website at http Awww socketmobile com 4 N IMPORTANT The information in this User s Guide pertains to 1D STO P laser versions of the Socket Bluetooth Cordless Hand Scanner q Je CHS which have the following part numbers NI iia lt CHS version Type of Barcode Scanner Part Number Class 2 laser 8550 00063 Class 2 laser durable casing 8550 00064 If you have a different version of the CHS download the appropriate manual online at http www socketmobile com support downloads data collection series7 ss10 page Detail COPYRIGHT NOTICE 1 INTRODUCTION 2 SCANNER SETUP 3 SETUP FOR APPLE IOS 4 SETUP FOR ANDROID 5 SETUP FOR WINDOWS PC 6 SETUP FOR WINDOWS MOBILE 7 SETUP FOR BLACKBERRY APPENDIX A SPECIFICATIONS APPENDIX B SAFETY AND USAGE TIPS APPENDIX C BARCODE LABEL SPECIFICATIONS APPENDIX D DECODE ZONE APPENDIX E COMMAND BARCODES APPENDIX G SPECIAL BUTTON SEQUENCES APPENDIX H CAB INSTALLATION APPENDIX CONNECTION BARCODES APPENDIX J TROUBLESHOOTING APPENDIX K TECHNICAL SUPPORT LIMITED WARRAN
11. see Appendix F for instructions and delete any Unknown devices in the Bluetooth paired devices list 112 APPENDIX K TECHNICAL SUPPORT If you have trouble installing or using the CHS Socket has different support options to help you Online Knowledge Base Search for articles Frequently Asked Questions or Hot Topics 24 hours a day http support socketmobile com EU_S1a asp Online Requests Register your product and submit a question to our Technical Support Team http support socketmobile com APPENDIX K TECHNICAL SUPPORT 113 LIMITED WARRANTY Socket Mobile Incorporated Socket warrants this product against defects in material and workmanship under normal use and service for one 1 year from the date of purchase Product must be purchased new from a Socket Mobile Authorized Distributor or Reseller Products purchased through non authorized channels are not eligible for this warranty support EXCLUDES Consumables such as batteries removable cables cases straps stylus memory cards chargers and CF to PC Card adapters 90 day coverage only An extended warranty is available separately for the Bluetooth Cordless Hand Scanner For more information please visit http support socketmobile com Incompatibility is not a defect covered by the Socket warranty During the warranty period Socket will at its option repair or replace the defective product at no charge when furnished with proof of retail purchase provide
12. t know my CHS model Calendar 4 The PDA will automatically try to search for and pair with the CHS In the list of found devices tap Socket CHS Select Socket Serial Port e Connection Wizard 9 m 4 27 Connection Wizard P m 4 28 a Bluetooth Connection Wizard i Bluetooth Connection Wizard Explore a Bluetooth device Explore a Bluetooth device 2 k 2 Socket CHS 0C7831 Socket CHS T Mobile _LEO Service Selection oc7831 a Please select the service s offered by this device you would like to create connection shortcuts for Security Use a secure encrypted connection Cancel Back Next o gt 5 After pairing is complete tap ok Close Socket EZ Pair 6 The CHS registration screen will appear Follow the instructions to register your scanner or tap Cancel to register later 6 SETUP FOR WINDOWS MOBILE 69 Broadcom These instructions are based on the HTC HD2 running Windows Mobile 6 5 70 M 1 Make sure HTC Sense is disabled Start ag Settings In the bottom right corner tap Menu All Settings Today Items tab Make sure the box HTC Sense is unchecked M i 2 Tap Start ao SocketScan 10 folder SocketScan 10 3 In the Today screen tap on the SocketScan 10 icon ML in the task tray In the pop up menu tap Socket EZ Pair Tap 1D Scanner SocketScan 10 Settings About Exit 4 Your phone will automatically try to search for and pair with the C
13. v3 with any of the following devices running Windows Mobile 6 or later e Socket SoMo 650 or 655 e Device running Windows Mobile 6 or later with Broadcom Bluetooth stack v1 8 0 6501 or v1 9 3 Before you begin the instructions in this chapter make sure you have installed the batteries and charged the CHS as described in Chapter 2 Scanner Setup Cr Other devices running Windows Mobile 6 with the Microsoft Bluetooth stack may be TIP compatible CONNECTION OPTIONS For Windows Mobile the CHS offers two different connection options Bluetooth Pros Mode HID e No SocketScan 10 software installation Limited configuration options needed Limited to printable ASCII and some non Instructions printable characters on next Less efficient data communications for page barcodes containing lots of data Compatible only with SoMo SPP e Many configuration options Requires installation of SocketScan 10 e Broad character set including non software or application made with Instructions printable ASCII international SocketScan 10 SDK on page 39 keyboards e More efficient data communications for barcodes containing lots of data a Socket highly recommends that you use the CHS in SPP mode To learn more read TIP our white paper http www socketmobile com pdf techbrieflsocketscan 10 sdk_white paper pdf 58 OPTION 1 USING THE CHS IN HID MODE To pair the CHS with your SoMo Cr You only need to pair the CHS with your SoMo the firs
14. Bluetooth is enabled Open SocketScan 10 launching SocketScan 10 Settings by navigating to Your local drive Program Files Socket Mobile SocketScan 10 Bin Windows Click on SocketScan Settings exe Make sure Use keyboard wedge and Show keyboard wedge icon in task tray are selected and click OK SYMPTOM After the CHS connects an error message says the application failed to initialize properly POSSIBLE REASONS SOLUTION Your system is missing NET Framework Install the latest version of NET Framework with the 0xc0000135 appropriate version of Runtime software APPENDIX J TROUBLESHOOTING 109 SYMPTOM When I try to install SocketScan 10 an error message says Access is denied or I have insufficient privileges to complete installation POSSIBLE REASON SOLUTION You tried to install SocketScan on a Abort process Log into an administrative account and Windows 7 computer while not logged restart the installation into an administrative account SYMPTOM My CHS no longer connects to my computer POSSIBLE REASONS SOLUTION This is a Known issue with the Microsoft Make sure the CHS is discoverable and connectable In the Bluetooth stack in Windows Vista when Microsoft Bluetooth software select the Socket CHS in the using a USB Bluetooth adapter Bluetooth Bluetooth device list its status may be Already settings can sometimes become corrupted Connected Click Next If prompted enter the passkey after the compute
15. Bluetooth service select the CHS and click Finish Use Bluetooth v2 1 or later for best results Do not use Quick Connect Bluetooth serial devices when the CHS is in HID mode CF In the device search the CHS will appear as Socket CHS xxxxxx The characters in TIP brackets are the last six characters of the CHS Bluetooth Device Address BDA which is labeled inside the battery compartment CF Only computers running Bluetooth 2 0 will prompt for a passkey CHAPTER 5 SETUP FOR WINDOWS PC 47 6 Click on the SocketScan 10 icon in the system tray In the pop up menu click Socket EZ Pair SocketScan 10 Settings Socket EZ Pair CF If the icon does not appear open SocketScan 10 by clicking on the desktop short N Sokea TIP 7 Select 1D Scanner Scanner Type 1D Scanner models CHS 7E 7M 7P FRx 7C or 7Ci 2D Scanner models l CHS 74 FARI rA or aR 8 Select your CHS in the list and click Pair Choose Device Select a scanner From the list below to connect with SocketScan 10 on this device Then click the Pair button below IF your scanner is not listed below make sure your scanner is in SPP mode and pairing was done using the Bluetooth utility Fron your mobile device Refer to the Quick Start or Users Guide For your scanner For instructions Socket CHS 0C7831 Cancel 9 After they pair the computer will connect to the CHS indicated by a beep The CHS will then disconnect indicate
16. By default a carriage return is applied after scanned barcode data is entered To TIP disable the automatic carriage return you can use the Command Barcodes use the Data Editing barcode for disabling suffixes CF If no data is read in a few seconds the beam will turn off and you must try TIP again To Disconnect To disconnect turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off CF After the iPad disconnects from the CHS the soft keyboard will automatically reappear within a few seconds Automatic Reconnection After you power on the CHS it will automatically try to connect to the last computer it paired and connected to Make sure your computer is in range with Bluetooth enabled If the CHS is connected to your computer and gets disconnected it will try to reconnect Make sure the computer is on and in range If the CHS cannot reconnect after several attempts it will emit a long beep Press the trigger button to restart the reconnection process F The CHS can only be paired with one device at a time To use the CHS with a TIP different device see Appendix G for unpairing instructions Simultaneous Scanning and Soft Keyboard Support The CHS 7Mi and 7Pi support simultaneous use of the barcode scanner and the onscreen keyboard while entering data into an application This feature is enabled by default and can be modified by scanning a speci
17. E video amp Photos fel mus Cr In the device list the CHS will appear as Keyboard then as Socket CHS TIP xxxxxx The characters in brackets are the last six characters of the CHS Bluetooth Device Address BDA which is labeled inside the battery compartment 2 The CHS will connect to the Apple device If prompted enter the passkey 0000 four zeroes CF The CHS will beep once after it has connected and is ready to scan TIP barcodes The LED will also blink blue once every 3 seconds a For iOS the soft keyboard will automatically disappear a few seconds after Tip the CHS connects because the CHS is detected as a Bluetooth keyboard To make the onscreen keyboard appear while connected to the CHS see instructions on next page To scan barcodes 1 Open your application Place the cursor where you want to enter data 2 Hold the CHS about 4 inches 10 cm from the barcode and press and hold the trigger button An aiming beam will appear for 3 seconds Keep your hand steady while scanning For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen CHAPTER 3 SETUP FOR APPLE IOS 15 Cr After decoding the barcode and sending it to the computer by default the CHS TIP will vibrate and beep once the LED will flash green and the aiming beam will turn off You can use the Command Barcodes to modify the beep LED vibrate settings C7
18. Guide for your scanner For instructions Ee Socket CHS 0C7831 11 After pairing is complete tap ok Close Socket EZ Pair 12 The CHS registration screen will appear Follow the instructions to register your scanner or click Cancel to register later te Register CHS Register Socket CHS Scanner Please take a moment to register your CHS Scanner By registering your scanner you will be eligible to receive update notifications and product information Please include the name of the application you will be scanning data into Tap Next to continue Cancel Broadcom These instructions are based on the HP IPAQ 210 1 In Bluetooth Settings Tap on the Services tab Tap Serial Port Make sure Enable service is selected Tap ok z Bluetooth Settings Ga siZ 2 56 ok Bluetooth Services Services w File Transfer a Information Exchange Serial Port 4 Personal Network Server Service settings Enable service Authorization required Authentication Passkey required A S F 2 Tap Start a Programs SocketScan 10 folder SocketScan 10 N 3 In the Today screen tap on the SocketScan 10 icon in the task tray In the pop up menu tap Socket EZ Pair Tap 1D Scanner S Te SocketScan 10 P a 2 33 ok To use Socket EZ Pair select scanner type 1D Scanner models CHS 7E 7M 7P or NR 2D Scanner models CHS 7X ZARX SocketScan 10 Settings Socket EZ Parr I don
19. Requires installation of SocketScan 10 Broad character set including non software or an application made with Instruction printable ASCII international SocketScan 10 SDK s on page keyboards 66 More efficient data communications for barcodes containing lots of data Compatible with Android 2 1 and later Cr Socket highly recommends that you use the CHS in SPP mode To learn more read our white paper http www socketmobile com pdf techbrieflsocketscan 10 sdk_white paper pdf CF The instructions in this chapter are based on the Motorola Droid Pro running Tip Android 2 2 Menus will appear differently on different devices Some devices may require you to touch the Menu button to open the software menu CF When SocketScan 10 is running you can only use the keyboard provided by TIP SocketScan 10 You cannot use SWYPE or any custom keyboards To enable use of another keyboard you can use the SocketScan 10 SDK available separately http developer socketmobile com CHAPTER 4 SETUP FOR ANDROID 21 OPTION 1 USING THE CHS IN HID MODE Compatible with Android 2 2 and later devices that support HID for Peripheral TIP devices To pair the CHS with your Android device CF You only need to pair the CHS with your Android device the first time you try to connect 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high Cr The LED blinks blue once per second to show
20. and SocketScan 10 is running application will launch and work properly SYMPTOM When I open SocketScan 10 an error message says it cannot determine the Bluetooth stack POSSIBLE REASONS SOLUTION Bluetooth is not enabled on your PC Enable Bluetooth on your PC Make sure Bluetooth is fully initialized before opening SocketScan 10 SYMPTOM installed SocketScan 10 but the shortcut icon does not appear on my desktop POSSIBLE REASONS SOLUTION You incorrectly uninstalled a copy of Make sure SocketScan 10 is not running Uninstall SocketScan 10 before installing your SocketScan 10 When prompted make sure to restart current copy of SocketScan 10 the computer Re install SocketScan 10 110 TROUBLESHOOTING FOR WINDOWS EMBEDDED HANDHELD For help using SocketScan for Windows Embedded Handheld formerly known as Windows Mobile tap on the P icon SYMPTOM am using the CHS in SPP mode and get the CHS not connected icon in the task tray of the Today screen and can t trigger the scanner or scan any barcodes POSSIBLE REASON SOLUTION Your SoM is not connected to the CHS Make sure the CHS is on and in range and has enough battery power Try to reconnect You are trying to connect the CHS with an The first release of SocketScan 10 for Windows Mobile is HP iPAQ 100 or 200 series Pocket PC only compatible with the Socket SoMo Check back for HP iPAQ compatibility in future releases SYMPTOM The Bluetooth softw
21. certification number and the term IC before the equipment certification number only signifies that Industry Canada technical specifications were met Radio Frequency Interference Requirements Canada This Class B digital apparatus meets the requirements of the Canadian Interference Causing Equipment Regulations Cet appareil num rique de la Classe B respecte toutes les exigencies du Reglement sur le Mat riel Brouilleur du Canada CE Marking amp European Union Compliance Products intended for sale within the European Union are marked with a CE Mark which indicates compliance to applicable Directives and European Normes EN as follows Amendments to these Directives or ENs are included Normes EN as follows Applicable Directives e Radio and Telecommunications Terminal Equipment Directive 1999 5 EC e Low Voltage Directive 73 23 EEC Applicable Standards e EN 55 022 Limits and Methods of Measurement of Radio Interference Characteristics of Information Technology Equipment e EN 50 082 1 Electromagnetic Compatibility General Immunity Standard Part 1 Residential Commercial Light Industry e IEC 801 2 Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment Part 2 Electrostatic Discharge Requirements e IEC 801 3 Electromagnetic Compatibility for Industrial Process Measurement and Control Equipment Part 3 Radiated Electromagnetic Field Requirements e IEC 801 4 Electromagn
22. computer device SYMPTOM The Bluetooth device search has found multiple CHS devices and don t know which one to choose POSSIBLE REASONS SOLUTION The CHS is not paired with a host system Power off the CHS device s you do not want to connect to and and there are multiple CHS devices in range the Bluetooth device search Alternatively If the CHS works in SPP mode with your computer device you can use the SocketScan Scanner Settings utility to change the scanner s Bluetooth friendly name to something you can easily recognize APPENDIX J TROUBLESHOOTING 107 SYMPTOM When I scan a barcode odd behaviors occur such as different applications seem to be invoked in my system and or special characters are displayed in the application unexpectedly POSSIBLE REASON SOLUTION In HID mode the CHS will only properly Use the SocketScan 10 SDK to develop a custom read printable ASCII characters Non application that supports non printable ASCII characters printable ASCII characters or extended Learn more about the SDK at characters cannot be interpreted by the http www socketmobile com products sdk scanner Printable ASCII characters are numbers between 0x20 and 0x7E and any ASCII characters that fall outside of this scope are considered as non printable SYMPTOM When I press the Shift Caps Lock or Ctrl key on my keyboard it affects the data output from my CHS to my computer POSSIBLE REASON SOLUTION
23. data into We will send identifying information about your scanner to Socket Mobile Bt Address 00C01BOFC66A Tap Next to continue Cancel 30 TIP After you have connected you can touch Socket CHS in the main screen of SocketScan 10 to view basic scanner properties To scan barcodes 1 Open your application Place the cursor where you want to enter data 2 Press the trigger button to scan a barcode Make sure the aiming beam extends across the entire width of the barcode puitiin i pamit iM gi For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen F After decoding the barcode and sending it to the phone tablet by default the CHS TIP will beep once and vibrate the LED will flash green and the aiming beam will turn off You can use the Scanner Settings utility see next page or Command Barcodes to modify the beep LED vibrate settings ia To configure an automatic Carriage Return or Tab after each scan of data use the TIP Scanner Settings utility see next page or Command Barcodes Cr If no data is read in a few seconds the beam will turn off and you must try again TIP To Disconnect To disconnect turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off Automatic Reconnection After you power on the CHS it will automaticall
24. device search will begin Add a Device 4S Allow a Device to Connect Show Bluetooth Devices Send a File Receive a File Join a Personal Area Network Open Settings Remove Irnan 2 In the device list select Socket CHS xxxxxx and click Next 3 If prompted select Enter the device s pairing code Enter the passkey 0000 four zeroes Click Next Slc a painng option Create a pairing code for me Tha device have a beypad l nonon Enter the device s paining code Socket CHS Ta 0F3CEF Ths Cavite cime wih d Air de d Check ior one on Ehe ditoe or in the derie maeaal 4 Pair without using a code This type of device roch as a moure doe not TEJA a Tetlie pirrer bani Hii ind bet Eri dboirt MA ainia ciati 4 Follow the remaining screens to complete the wizard Microsoft l l 3E ae Windows 1 Right click on the Bluetooth icon in the system tray notification area In Vista XP the pop up menu click Add a Bluetooth Device 2 In the welcome screen check the box My device is set up and ready to be found Click Next A device search will begin 3 In the device list select Socket CHS xxxxxx Click Next Select the Bluetooth device that you want to add erase 3 a LEONARD New device All other devices S 00 13 e0 7a 09 b4 New device If you don t see the device that you want to add make sure that it is turned on Follow the setup instructions that came with the de
25. more information on Socket Mobile accessories for the CHS please visit http ww1 socketmobile com products bluetooth scanners accessories bt aspx For more information on accessories from Taylor Made Cases Viziflex Seels or other Socket Mobile partners please visit http Aww1 socketmobile com products star custom cases aspx CHAPTER 1 INTRODUCTION 7 HARDWARE FEATURES Product Diagram Trigger button Status indicator LED Power button Stylus tip Protective rubber bumper 7Pi only Power connector For 7Pi remove rubber cap to access Status Indicator LED LED Activity Meaning Bluetooth Blue 1 blink per second Bluetooth radio is on but not connected 1 blink per 3 seconds CHS connected to host device Good Read Green On Data successfully scanned and transmitted to host device On and connected to charger Battery full Battery Red Blinking 20 or less battery capacity remaining Status Indicator Beeps Beep Pattern Meaning 1 beep CHS connected to host device and ready to scan barcodes You have double pressed the power button and the CHS has 1 beep low enabled support for simultaneous scanning and onscreen keyboard entry for Apple iOS peep puting a e Data successfully scanned and sent to host device setting 2 beeps same tone CHS disconnected from host device CHS unsuccessfully tried 30 times to connect to the last host 1 long beep device it paired with The CHS will become discoverable
26. of your CHS To change the Bluetooth friendly name touch Socket CHS Gay New Scanner Name Battery Level 70 Scanner Name Socket CHS OF3C4F OK Cancel 32 Configuration 1 In the main screen of Scanner Settings touch Menu Configuration Socket CHS OFSDFC Configuration Symbology 2 In the Configuration screen enter the appropriate settings Q ATH 5 06 pm Configuration Good scan beep Good scan flash Vibrate mode Enable data suffix a Append a Carriage Return character lt CR gt Append a TAB character Selected Character lt ESC VW e Good scan beep Select to have the CHS beep to indicate that data was successfully decoded and transmitted to the Android device e Good scan flash Select to have the CHS LED turn green to indicate that data was successfully decoded and transmitted to the Android device e Vibrate mode Select to have the CHS vibrate to indicate that data was successfully decoded and transmitted to the Android device e Scanned data suffix Select if you would like to automatically add a carriage return tab or select another character or function after each scan of data CHAPTER 4 SETUP FOR ANDROID 33 Symbology 1 In the main screen of Scanner Settings touch Menu Symbology Socket CHS OFSDFC Configuration Symbology 2 In the Symbology screen enable or disable the appropriate symbologies barcode types 34 Australia Post Aztec
27. pair the CHS with your Android device Cr You only need to pair the CHS with your Android device the first time you try to TIP connect Cr The following instructions are based on Socket EZ Pair a feature of SocketScan 10 TIP software For instructions on how to connect by generating and scanning a special barcode please see Appendix 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high CF The LED blinks blue once per second to show that the Bluetooth radio is on but not TIP connected 2 Scan this barcode to change the CHS to SPP mode Afterwards the CHS will beep 3 times FNBOOF40000 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen 3 Make sure the device has Bluetooth on Start a device search scan for devices O ep itil te 4 03 pm Bluetooth settings Bluetooth Device name DROID PRO Discoverable Discoverable for 103 seconds Scan for devices Bluetooth devices 26 4 In the list of found devices touch Socket CHS to ATu EJ 5 47 pm Bluetooth settings Dae 18 18 Discoverable for 27 seconds Enhanced Stereo Improved battery life and M quality for supporting devices P3 audio Scan for devices Bluetooth devices T Mobile_LEO Pair with this device Socket CHS OF3C4F Pair with this device Pocket_PC Pair with this device Cr The CHS will appear in t
28. the system in any way and 2 connecting external antennas to the B uetooth Cordless Hand Scanner is prohibited This device and its antenna must not be co located or operated with any other antenna or transmitter To comply with Industry Canada RF exposure compliance requirements the following antenna installation and device operating configurations must be satisfied The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population consult Safety Code 6 available at Health Canada s website http www hc sc gc ca If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user may try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna of the radio or television Increase the distance separating the equipment and the receiver Connect the equipment to an outlet on a different branch circuit than that of the receiver Consult the dealer or an experienced radio TV technician for help 117 The user may find the following booklet helpful How to Identify and Resolve Radio TV Interference Problems available from the U S Government Printing Office Washington D C 20402 Canada Certification The marking of IC 2394A CHS1 on the device means 2394A CHS1 is the
29. the CHS supports SPP mode for your OS you can generate and scan special barcodes to quickly connect to a computer or device 1 Power on the CHS Make sure the CHS is in SPP mode If needed use the appropriate Command Barcode to change the scanner mode Enable Bluetooth on your computer or device Find out the Bluetooth Device Address of your computer or device You can use the Bluetooth software to find this out Open SocketScan 10 In SocketScan 10 Settings make sure an incoming COM is selected Use a barcode generating application or website e g http barcode tec it com to create and print a barcode with the following properties Symbology Code 128 Data H ENIXXxXxxXXXXXXx Where the xxxxxxxxxxxx is the 12 character Bluetooth Device Address of the computer or device you want to connect to Barcode Module Width approx 1 inch or 3 cm recommended Scan the barcode that you created If prompted accept the Bluetooth connection If prompted for a passkey enter 0000 four zeroes 106 APPENDIX J TROUBLESHOOTING GENERAL TROUBLESHOOTING ALL OS SYMPTOM When I try to scan aim the beam at the barcode but no data appears on my screen and the beam eventually turns off POSSIBLE REASON SOLUTION barcode or at an incorrect angle accustomed to the most effective position Try scanning a barcode that is correctly formatted printed damaged or poorly printed clearly and in good co
30. to connect fo Your scanner Port Description COMIS Standard Serial over Bluetooth link COM19 Use keyboard wedge Show keyboard wedge icon in task tray no scanner hs scanner s connected Enable VIN decode CF Click Ports if a suitable incoming Bluetooth COM port is not listed and you would Tip like to add one Also if SocketScan Settings lists multiple COM ports you can determine if any are already paired to a Socket Bluetooth barcode scanner and or which one is incoming Cr For the Toshiba Bluetooth stack incoming COM ports are listed as LocalCOM TIP Server Ce For most users Use keyboard wedge and Show keyboard wedge icon in tray TIP should be selected For more information on keyboard wedge and VIN decode options please see SocketScan 10 Settings 6 After making all your selections in SocketScan 10 Settings click OK 7 In the last screen of the software installation wizard click Finish If prompted restart your computer After installation a SocketScan 10 shortcut will appear on your desktop Click it to ka TIP quickly launch SocketScan 10 Sad vanes wit 44 To pair and connect the CHS with your computer CF You only need to pair the CHS with you computer the first time you try to connect TIP F The following instructions are based on Socket EZ Pair a feature of SocketScan 10 TIP software For instructions on how to connect by generating and scanning a special barcode please see Append
31. to scan barcodes The LED will also blink blue once every 3 seconds To scan barcodes 1 In your application place the cursor where you want to enter data 2 Hold the CHS about 4 inches 10 cm from the barcode and press and hold the trigger button An aiming beam will appear for 3 seconds Keep your hand steady while scanning yan Bluetooth For example try scanning the following barcode ABCDE12345 Cr After data is read and sent to the Apple device by default the CHS will beep TIP once and vibrate the LED will flash green and the beam will turn off E If no data is read in a few seconds the beam will turn off and you must try again CF Watch a video http www youtube com watch v VhtttoC6ROs To Disconnect To disconnect turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off 7 After the iPad disconnects from the CHS the soft keyboard will automatically TIP reappear within a few seconds Automatic Reconnection After you power on the CHS it will automatically try to connect to the last computer it paired and connected to Make sure your computer is in range with Bluetooth enabled If the CHS is connected to your computer and gets disconnected it will try to reconnect for 45 seconds Make sure the computer is on and in range If the CHS cannot reconnect after several attempts it will emit a long beep Power cyc
32. try again To Disconnect To disconnect turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off Automatic Reconnection After you power on the CHS it will automatically try to connect to the last tablet it paired and connected to Make sure your tablet is in range with Bluetooth enabled If the CHS is connected to your tablet and gets disconnected it will try to reconnect for a few minutes Make sure the tablet is on and in range If the CHS cannot reconnect it will give a long beep Power off and on the CHS to restart the reconnection process The CHS can only be paired with one device at a time To use the CHS with a TIP different device see Appendix G for unpairing instructions 7 SETUP FOR BLACKBERRY 81 82 USING THE CHS IN SPP Mope BLACKBERRY OS To install the software You can install SocketScan 10 software either by downloading directly to the smartphone or synchronizing to a host PC with BlackBerry Desktop Manager Downloading to the Smartphone 1 Make sure your smartphone is connected to the Internet 2 Open the Browser to http Awww socketmobile com blackberry 3 The SocketScan for BlackBerry installation screen will appear Read the information in the screen If you accept the license agreement click Accept 4 The download screen will appear Click Download The smartphone will download and install SocketScan 5 A
33. 13 00 an 2 20 10 mil 18 00 r 2 20 _ __100 UPG a00 15 38 1 2 20 mil 28 00 L 2 50 ooo 29 00 g INGE 2800 20 50 8 55 mil 42 00 BELEE REE UD E a n E E E a E a E S a a S a a O D a a E e E a In 0 5 10 15 20 25 30 35 40 45 cm 0 12 7 25 4 38 1 50 8 63 5 76 2 88 9 101 6 114 3 Depth of Field Minimum distance determined by symbol length and scan angle APPENDIX D DECODE ZONE 97 APPENDIX E COMMAND BARCODES Scan command barcode s to quickly configure the CHS 7Mi or 7Pi By default the CHS is in HID mode as a Keyboard device Many of the command barcodes only work with a scanner in a particular Bluetooth mode as indicated by the header row of each table All Bluetooth Connection Modes OK Scan only with CHS in SPP or iOS Mode Scan only with CHS in HID Mode A IMPORTANT Print out the page to scan the barcodes Do not scan them onscreen A IMPORTANT Make sure the CHS is not connected to computer device before scanning a command barcode i By default the CHS is in HID mode as a Keyboard device You may want to cover adjacent barcodes before scanning a command barcode to prevent scanning the wrong code For scanners in Bluetooth SPP or iOS mode you can alternatively configure some settings by using the Scanner Settings app The CHS can only be paired with one device at a time To use the CHS with a different device see Appendix F for unpairing instructions 98 APPENDIX F COMMAND
34. 6 1351 requires previous purchase of SocketCare Plus 2 or 3 year program SYSTEM COMPATIBILITY REQUIREMENTS COMPATIBLE DEVICES For the latest device compatibility information please use our Compatibility Checker http www socketmobile com CompatibilityChecker OS System Compatibility Requirements Compatible Bluetooth HID Bluetooth SPP Devices Support Support e Windows 7 Vista XP E e Microsoft Toshiba or Broadcom Bluetooth v vV stack Windows Windows Embedded Handheld 6 x v Microsoft or Embedded Broadcom Handheld Bluetooth stack Apple iOS iPod touch 5 generation iPod touch 4 generation iPod touch 3 generation iPhone 5 iPhone 4S iPhone 4 iPhone 3GS iPad mini iPad 3 generation iPad 2 iPad Mac OS e Mac OS X 10 4 to 10 6 6 for Mac MacBook r e Bluetooth driver v2 24f3 v1965 or v2 37f1 Android OS Android 2 1 or later v Android 2 2 or later v Android 2 1 with HID or later support BlackBerry BlackBerry OS 5 0 0 714 or later for Bold 9700 e OS BlackBerry PlayBook Compatibility verified for latest models at time of testing Other models or Bluetooth driver versions not tested Other devices not tested with SocketScan 10 and may require the previous software version ADDITIONAL DOCUMENTATION Download Quick Start Guides Command Barcode Sheets or other manuals http Awww socketmobile com support downloads data collection series7 ss10 page Detail CHAPTER 1 INTRODUCTION 5 AB
35. 73E9 Scanner type CHS Scanner Firmware 3 2 0 1709 06197010 Battery level LLL LLLLLLLLUL 55 3 After viewing the information click OK to exit CHAPTER 5 SETUP FOR WINDOWS PC 51 SocketScan 10 Settings 1 Click on the SocketScan 10 icon or in the system tray In the pop up menu click SocketScan 10 Settings Socket CHS 007831 SocketScan 10 Settings Scanner settings Socket ES Pair Abou Exit 2 The SocketScan 10 Settings screen will appear reporting the manufacturer of the computer s Bluetooth stack and the computer s Bluetooth Device Address Bluetooth stack Microsoft A Bluetooth address 00 00 16 0C 59 22 Incoming Bluetooth serial ports Check one or more ports to connect to your scanner Port Description COMZ0 Standard Serial over Bluetooth link comzo Use keyboard wedge Show keyboard wedge icon in task tray o scanner KE scanner s connected Enable VIM decode e Port An incoming Bluetooth serial COM port must be selected for the CHS connection o If asuitable port is not listed in SocketScan 10 Settings click Ports to use your computer s Bluetooth software to add one o Toshiba Bluetooth stack To identify an incoming COM click Ports In your computer s Bluetooth software incoming ports are labeled as LocalCOM Server e Use keyboard wedge Should be selected in most cases unless you plan to use the SDK e Show keyboard wedge icon in tray
36. BARCODES Bluetooth Connection Modes SPP Mode Configures the CHS to Serial Port Profile SPP mode HFNBOOF 400004 Required for BlackBerry optional for Windows and Android HID Mode default Configures the CHS to Human Interface Device HID mode The CHS will be discoverable as a Keyboard to other B uetooth devices HFHMBOOF 40001 Required for Apple iOS Mac OS HID Peripheral Changes a CHS in HID Keyboard mode to HID Peripheral mode HFA BOOT 000S500H Optional for Windows and Android HID Keyboard defau t Required for Mac OS optional for Apple iOS HFNBOOO1 0005404 iOS Mode Required for Apple iOS applications developed with SocketScan 10 SDK HENBOOFAUDOSH Bluetooth Connection Roles For SPP or iOS Mode Only Acceptor default Configures the CHS to accept a Bluetooth connection puts the CHS in HFNAH discoverable mode Initiator Configures the CHS to initiate a connection to a computer device with the Bluetooth Address specified in the barcode The barcode must be formatted in Code 128 and contain the data You must create a custom barcode for each computer device that you want to connect to the CHS FNlaabbccddeeff Use barcode generating software or website l e g http barcode tec it com such that aabbccddeeff is the Bluetooth Address of the computer device you want to connect to the CHS APPENDIX F COMMAND BARCODES 99 Automatic Reconnection Settings ENABLE Automatic R
37. EC 60950 1 UL 60950 1 CAN CSA C22 2 EN60950 1 Environmental RoHS EMI RFI FCC Part 15 Class C RSS 210 iCES 003 C Tick CISPR 22 CE EN55022 EN55024 TELEC IEC 60825 1 EN 60825 1 Apple iOS certification for iPad iPhone iPod touch Bluetooth QD ID B0164000 92 About Bluetooth Range This product features a powerful Class 1 Bluetooth radio to provide the maximum possible range As with all wireless technologies the connection range can vary widely depending on many factors such as the brand and placement of the host device the type and size of physical obstacles and the presence and activity level of competing radio transmissions In range testing of this product while connected to a variety of typical host devices with Class 1 radios functional connection distances from 18 to 100 ft have been experienced depending on the environment The following conditions appear to reduce the Bluetooth connection range e The presence of soft absorbent materials such as paper fiberglass insulation foam material in office cubical walls carpeting and to a lesser extent even sheetrock and wood construction materials e Human bodies or containers of liquid positioned between the host and the CHS e The presence and activity level of competing B uetooth 802 11 Wi Fi or other proprietary systems using the same 2 4 GHz frequency e Metal in a grid pattern such as chain link fencing or chicken wire This type of material may bloc
38. HS e Inthe device list select Socket CHS Select Socket Serial Port e Select an available COM port for SocketScan 10 to use 2 Bluetooth amp a a x GH xX AN Bluetooth G 2 m x m xX Select a device Wd Socket CHS 0C7831 Socket Serial Port xg Connect to a wireless seria port on the device I lt No Name gt LEN TABLET WA Socket CHS 0C7831 Select Cancel 5 After pairing is complete tap ok Close Socket EZ Pair ae SocketScan 10 a wax Gi OK To use Socket EZ Pair select scanner type SocketScan 10 ib Pairing complete The s scanner will connect to your mobile device and confirm with a single connection beep I don t know my CHS model 6 The CHS registration screen will appear Follow the instructions to register th scanner or tap Cancel to register later To scan barcodes 1 Make sure the CHS is connected to the SoMo indicated by the CHS icon IN in the task tray Open your application Place the cursor where you want to enter data Press the trigger button to scan a barcode Make sure the aiming beam extends across the entire width of the barcode guinea evant si PS Fir F For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen CF After decoding the barcode and sending it to the computer by default the CHS TIP will beep once and vibrate the LED will flas
39. OUT BLUETOOTH HID AND SPP MODES The CHS support two kinds of Bluetooth connections known as Bluetooth profiles SPP Serial Port Profile and HID Human Interface Device each with its advantages and disadvantages By default the CHS is set to HID mode for Keyboard devices which requires no SocketScan 10 software installation For better performance Socket highly recommends that you use SPP mode or iOS mode especially if scanning barcodes that contain a lot of data Feature CHS with HID mode CHS in SPP mode for Android CHS in IOS mode No software installation required Supports SocketScan 10 software with Socket EZ Pair Windows E Non printable ASCII UNICODE international keyboard support International keyboard French German as supported by OS as supported by support Spanish os Parsing data checks ae a S E SocketScan 10 SDK Binary data wi DK methods barcodes or special barcodes options options options Barcodes containing a lot Less efficient More efficient data More efficient data of data communications may lead communications communications to slower performance To change modes use the Command Barcodes in Appendix E To learn more about HID and SPP please read our white paper http www socketmobile com pdf techbrief socketscan 10 sdk_white paper pdf ABOUT SOCKETSCAN 10 SOFTWARE SocketScan 10 keyboard wedge software for Android Windows and BlackBerry OS enters scanned data directly into any p
40. Select to have a system tray icon appear that conveniently indicates whether the CHS is connected to the PC Enable VIN decode Select to have SocketScan 10 only send a 17 character Vehicle Identification Number i e omit any prefix suffix included in a VIN barcode e Ports Click to access your computer s Bluetooth software to add or view properties of Bluetooth COM ports including which are incoming outgoing 3 After making changes click OK 52 Scanner Settings CF You can access Scanner Settings only when the CHS is connected to your computer TIP 1 Click on the CHS icon settings in the system tray In the pop up menu click Scanner Socket CHS OC7831 SockekScan 10 Settings Scanner settings Socket EZ Pair About Exit 2 The Scanner Settings screen will appear with an empty field For the Microsoft and Broadcom Widcomm Bluetooth stacks the CHS will also beep twice when in disconnects from SocketScan 10 3 After a few seconds the CHS will connect to Scanner Settings indicated by a beep Your CHS will be listed on the screen Make sure your CHS is selected and click Properties a7 Scanner Settings Scanners Socket CHS 5 The utility will read your scanner settings CHAPTER 5 SETUP FOR WINDOWS PC 53 54 6 The General properties screen will appear reporting the Bluetooth friendly name Bluetooth Device Address Type of device firmware version and ba
41. Socket Bluetooth Cordless Hand Scanner CHS 1D Laser Models 7M 7Pi User s Guide Bluetooth socket mobile 8 2013 Document 6410 00344 A COPYRIGHT NOTICE Copyright 2013 Socket Mobile Inc All rights reserved Socket the Socket logo Battery Friendly Socket Bluetooth Cordless Hand Scanner SocketCare SocketScan Mobility Friendly and SoMo are trademarks or registered trademarks of Socket Mobile Inc Bluetooth and the Bluetooth logos are registered trademarks owned by Bluetooth SIG Inc U S A and licensed to Socket Mobile Inc Apple iPad iPhone iPod touch and Mac OS are trademarks of Apple Inc registered in the U S and other countries App Store is a trademark of Apple Inc All other brand and product names are trademarks of their respective holders The Socket Bluetooth Cordless Hand Scanner includes technology licensed under United States Patent Numbers 5 902 991 7 429 000 B1 and D526 320 S Reproduction of the contents of this manual without the permission of Socket Mobile is expressly prohibited Please be aware that the products described in this manual may change without notice Feel free to contact Socket Mobile at Socket Mobile Inc 39700 Eureka Drive Newark CA 94560 4808 USA 1 510 933 3000 USA Canada Toll free 1 800 552 3300 http Wwww socketmobile com contact Other than the above Socket Mobile can assume no responsibility for anything resulting from the application of
42. T OR APPLICATION DESCRIBED HEREIN 114 SOCKETSCAN SOFTWARE LICENSE AGREEMENT PLEASE READ THIS SOFTWARE LICENSE AGREEMENT LICENSE BEFORE USING THE SOCKETSCAN SOFTWARE BY USING THE SOFTWARE YOU ARE AGREEING TO BE BOUND BY THE TERMS OF THIS LICENSE IF YOU DO NOT AGREE TO THE TERMS OF THIS LICENSE DO NOT USE THE SOFTWARE I License Any software tools utilities sample code documentation fonts and other materials accompanying this License whether on disk print or electronic documentation in read only memory or any other media are licensed to you by Socket Mobile Inc for use only under the terms of this License and Socket Mobile reserves all rights not expressly granted to you The rights granted herein are limited to Socket Mobile Inc s and its licensors intellectual property rights in SocketScan Software and do not include any other patents or intellectual property rights You own the media on which SocketScan Software is recorded but Socket Mobile and or Socket Mobile licensor s retain ownership of SocketScan itself SocketScan Software in this package and any copies you make and modifications you obtain in the future are subject to this License Permitted Uses and Restrictions SocketScan Software is designed for use only in conjunction with Socket Mobile products and is unlimited as to use for this purpose You may not decompile reverse engineer disassemble modify rent lease loan sublicense and distribute the sof
43. TY SOCKETSCAN SOFTWARE LICENSE AGREEMENT REGULATORY COMPLIANCE TABLE OF CONTENTS 10 13 21 3 08 78 91 94 96 97 98 104 105 106 107 113 114 115 116 1 INTRODUCTION Thank you for purchasing the Socket Bluetooth Cordless Hand Scanner CHS The CHS is a portable handheld barcode scanner that is small light comfortable to use 1D laser models enable you to scan data from 1D barcodes into a wide variety of computers smartphones and PDAs SCANNER MODELS 1D LASER VERSIONS Model Scanning Engine Durable Exterior Casing Class 2 laser OC Class 2 Laser PACKAGE CONTENTS Socket Bluetooth 2 NiMH Lanyard Belt Clip Cordless Hand Scanner USR ACEHAN Kit rechargeable retractable tet AAA batteries PRODUCT REGISTRATION Socket highly recommends that all customers register their products Product registration is required to access technical support You can also opt in for special offers upgrades and new product information Register online at http support socketmobile com Alternatively if you install SocketScan 10 or Scanner Settings you can register the CHS through the software SOCKETCARE SERVICE PROGRAM SocketCare is an enhanced service program that features priority technical support accelerated repair and replacement and more http Awww socketcare com e SocketCare Plus 2 year SKU SC1804 1349 e SocketCare Plus 3 year SKU SC1805 1350 e SocketCare Comprehensive Plus SKU C180
44. The CHS can only be paired with one device at a time To use the CHS with a TIP different device see Appendix G for unpairing instructions SOCKETSCAN 10 SPECIAL FEATURES SPP Mope ONLY SocketScan 10 software offers a variety of special features System tray icon Indicates CHS connection status at a glance Basic scanner information Quick view of basic scanner properties SocketScan 10 Settings Utility for configuring COM port keyboard wedge system tray icon and VIN mode Scanner Settings Utility lets you view Bluetooth properties battery level adjust beep LED vibrate settings test barcodes and more About Software version information System Tray Icon When SocketScan 10 is running an icon that indicates the CHS connection status will appear in the system tray notification area CHS not connected N CHS connected Basic Scanner Information 1 CF To view more detailed scanner properties use Scanner Settings TIP CF You can only view Basic Scanner Properties when the CHS is connected to your TIP computer Click on the CHS icon N in the system tray In the pop up menu click Socket CHS Socket CHS 027831 SocketScan 10 Settings Scanner settings Socket EZ Pair About Exit 2 A screen will appear displaying basic information about your CHS including the Bluetooth friendly name scanner type firmware and battery level F Scanner name Socket CHS 0F
45. You are using the CHS in HID mode as a Determine how your computer implements HID keyboard Keyboard class device devices SYMPTOM When I scan some barcodes with the CHS in SPP mode the data is truncated or some characters are corrupted POSSIBLE REASON SOLUTION The barcode data has illegal characters If you have a truncated barcode you can view the raw SocketScan 10 is designed to read ASCII data without any conversions by using the Test option of characters between 0x20 Space and 0x7F Scanner Settings with hexadecimal format selected If you need to scan data that is not 7 bit ASCII e g Double Byte MultiByte or UNICODE for Kanji simplified Chinese etc use the SocketScan 10 SDK 108 TROUBLESHOOTING FOR WINDOWS PC To SYMPTOM am using the CHS in SPP mode and get the CHS not connected icon in the system tray and can t trigger the scanner or scan any barcodes POSSIBLE REASON SOLUTION Your PC is not connected to the CHS Make sure the CHS is on in range and has enough battery power Try to reconnect SYMPTOM When I try to access SocketScan 10 get an error message saying the installed version of the application could not be determined POSSIBLE REASON SOLUTION You installed SocketScan 10 while logged Log into the account you used while installing SocketScan1 into a different account Alternatively you can install SocketScan 10 for every user account that plans to use the CHS SYMPTOM
46. able data suffix e Append a Carriage Return lt CR gt Append a TAB character Selected character lt SOH gt Good scan beep Select to have the CHS beep to indicate that data was successfully decoded and transmitted to the smartphone Good scan flash Select to have the CHS LED turn green to indicate that data was successfully decoded and transmitted to the smartphone e Vibrate mode Select to have the CHS vibrate to indicate that data was successfully decoded and transmitted to the smartphone Scanned data suffix Select if you would like to add a carriage return or tab after each scan of data 7 SETUP FOR BLACKBERRY 89 2 After entering any settings click Menu Save Scanner Settings Symbologies 1 In Scanner Settings click Menu Symbologies Press the space bar to enable or disable symbologies Bookland Ean Chinese 2 of 5 Codabar Code 11 Code 39 Code 39 Extended Code 39 Trioptic Code 93 x N O O Q M N Co CF TIP Cr TIP Enabling all possible symbologies will make the decode process slightly longer The RSS symbology is now known as GS1 DataBar If you would like to read UPC A symbols be sure to disable GS1 DataBar so that Tip GS1 DataBar symbols don t get mistakenly decoded 2 After entering any settings click Menu Save Scanner Settings Test 1 In Scanner Settings click Menu Test Scanner Settings Socket CHS 0C7831 Test Configu
47. al command barcode 1 Connect the CHS to your Apple device 2 Open your application and place the cursor where you want to enter data 3 You can begin scanning barcodes To open or close the onscreen keyboard quickly double press the CHS power button like double clicking a mouse CF After you double press the power button the CHS will beep to indicate that the TIP onscreen keyboard was enabled disabled CF Watch a video http www youtube com watch v VhtttoC6ROs TIP OPTION 2 USING THE CHS IN IOS MODE In iOS mode the CHS 7Mi and 7Pi can only scan barcodes into applications developed with SocketScan 10 SDK F The CHS 7Mi and 7Pi work in iOS mode with iOS applications developed TIP with SocketScan 10 SDK 10 0 8 or later To learn more about compatible applications available in the App Store online store e Please visit http www socketmobile com appstore e Contact your enterprise solution provider who can also help install and set up your iOS compatible application To download the SDK please join the Socket Mobile Developer Program 19 95 year http developer socketmobile com To pair and connect the CHS and Apple device CF You only need to pair the CHS with your Apple device the first time you Tip ty to connect The correct Bluetooth connection procedure may vary depending on which application you are using Please refer to your application TIP documentation for more information Internet access ma
48. are indicates that the CHS has connected but when I try to scan data it does not enter into my application POSSIBLE REASONS SOLUTION The CHS is in SPP mode and the SoMo has Use your Bluetooth utility to disable extra incoming multiple incoming Bluetooth serial ports Bluetooth serial ports enabled Is not running 10 SocketScan 10 SYMPTOM When I try to launch Scanner Settings get an error message saying that need to close the Keyboard Wedge application POSSIBLE REASONS SOLUTION The CHS is in SPP mode and connected to Close the Keyboard Wedge application and try launching the SoMo when you try to launch Scanner Scanner Settings again Settings SYMPTOM While using Scanner Settings the CHS disconnects and the Scanner Settings utility is non responsive POSSIBLE REASONS SOLUTION You tried to switch from one SocketScan Only use the pop up menu from the SocketScan task application to another by using an tray icon to switch between SocketScan applications assigned launch button SYMPTOM When I try to connect the CHS to my SoMo get an error message saying that an incompatible scanner tried to connect POSSIBLE REASONS SOLUTION The CHS is in SPP mode and the SoMo Free up a Bluetooth serial port for the CHS connection does not have any Bluetooth serial ports free APPENDIX J TROUBLESHOOTING 111 SYMPTOM When I try to use SocketScan 10 Keyboard Wedge or Scanner Settings in landscape mode
49. ave Fie D cancel e For Chrome click Save at the bottom of the screen Click on the link for the SocketScan10Setup exe file In the Security Warning screen click Run This type of File can harm your computer Are you SUC cave TD Aa you want to download SocketScanlOSetup exe 42 Download Socketican 127 0 HE exe 3 The installation wizard will launch Follow it to install software for Windows Desktop Sockrisean Ws Insallshicie Wirarc an 10 Wirkonme bo the natal hick Wira bn Socker CF If you are running an older version of SocketScan 10 uninstall it before TIP proceeding with the newer SocketScan 10 installation Make sure SocketScan 10 is not running before you start the uninstall process and when prompted restart your computer to complete the uninstallation 4 Amessage will state that on the next screen you will need to configure an incoming Bluetooth serial COM port to connect with the CHS Click Yes GONnhBinine socketscan Settings 2 J Onthe next screen you will need to configure an incoming client or local Bluetooth serial COM port to connect with your scanner CHAPTER 5 SETUP FOR WINDOWS PC 43 5 The SocketScan Settings screen will appear Select an available incoming COM port for SocketScan 10 to use Note the B uetooth stack at the top of the screen Bluetooth stack Microsoft Bluetooth address 00 CO 16 0C 59 22 Incoming Bluetooth serial ports Check one or more ports
50. beep 3 times FNBOOF40000 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen 3 In the Home Screen click Manage Connections 4 Click Set Up Bluetooth mm 1 06 FM 1 Turn All Connections Off IMobile Network ioe Bluetooth Services Status Set Up Wi Fi Network Set Up Bluetooth Mobile Network Options Wi Fi Ootions 5 Click Search Bluetooth Gicakled f Add Device Search for a device or Listen for a device to find me search Listen Cancel 84 6 In the list of found devices click Socket CHS Bluetooth Fnabled 3 Select Device o a o 8 Socket CHS 0C7831 03 el Pocket _PC FAWN E4200 Computer ALEX LAPTOP Se agaf S Se SU S gt ii EF ifi S sSbb com serecnshet 7 The CHS will appear in the Bluetooth search as Socket CHS xxxxxx where the TIP characters in brackets are the last 6 characters of the Bluetooth Device Address BDA which is printed on a label inside the battery compartment 7 If prompted for a passkey enter 0000 four zeroes 8 In the Home screen click Downloads SocketScan 10 9 If asked if you want to grant trusted application status click Yes 10 In SocketScan 10 click Menu Socket EZ Pair 11 Click 1D Scanner SocketScan 10 No device connected Socket EZ Pair About Close Switch Application o use Socket EZ Pair please select your type of scanner 1D Scanner models
51. ble symbologies may slow the decoding process CF The RSS symbology is now known as GS1 DataBar TIP F If you want to read UPC A symbols disable the GS1 DataBar option so that GS1 DataBar TIP symbols don t get mistakenly decoded 7 Tap ok to exit the Scanner Settings 6 SETUP FOR WINDOWS MOBILE 75 76 8 If desired tap Test to test scanning a barcode Scanner Settings y ok Connected scanners Socket CHS OFT3E9 9 Scan a barcode that you would like information about SocketScan will report the barcode s symbology data length and data in your choice of ASCII text or Hexadecimal format Scanner Settings Symbology Code 128 Lenath Data 13 View 7 000 007 25 59 4D 49 20 SA 24 24 SYMIOZAt O0 00C 55 42 5L 27 55 10 After testing a barcode tap ok Tap ok to exit Scanner Settings About 1 Tap on the SocketScan 10 icon M or IN in the task tray In the pop up menu tap About SocketScan 10 et ME Thursday 5 55 PM December 09 2010 Wi Fi OFF B On Tap here to set owner information WAN No card detected Slot Enabled No tasks Bs Mo upcoming appointments Live Search amp No unread messages Getting Started SocketScan Settings Socket E2 Pair About 2 The About screen will appear reporting information about your version of SocketScan 10 SocketScan 10 IN SO cket SocketScan 10 Socket Mobile Incorporated Copyright c 2005 2010 all rights re
52. btained In particular but without limitation SocketScan Software may not be exported or re exported a into or to a national or resident of any U S embargoed countries currently Cuba Iran Iraq Libya North Korea Sudan and Syria or b to anyone on the U S Treasury Department s list of Specially Designated Nationals or the U S Department of Commerce Denied Persons List or Entity List By using Socket Mobile Software you represent and warrant that you are not located in under control of or a national or resident of any such country or on any such list Government End Users Socket Mobile Software and related documentation are Commercial Items as that term is defined at 48 C F R 2 101 consisting of Commercial Computer Software and Commercial Computer Software Documentation as such terms are used in 48 C F R 12 212 or 48 C F R 227 7202 as applicable Consistent with 48 C F R 12 212 or 48 C F R 227 7202 1through 227 7202 4 as applicable the Commercial Computer Software and Commercial Computer Software Documentation are being licensed to U S Government end users a only as Commercial Items and b with only those rights as are granted to all other end users pursuant to the terms and conditions herein Unpublished rights reserved under the copyright laws of the United States Limited Warranty Socket Mobile warrants that the original disk is free from defects for 90 days from the date of delivery of the Software Socket Mobi
53. ce at a time To use the CHS with a TIP different device see Appendix G for unpairing instructions OPTION 2 USING THE CHS IN SPP MODE To install SocketScan 10 software Advanced Users See Appendix H for CAB file installation instructions If you have the Socket SoMo 655 or SoMo 650 running Windows Mobile 6 Service Pack 8 or later SocketScan 10 is pre loaded To install in the Today screen tap Getting Started 1 Make an active connection between your PDA and a host PC Use a USB serial connection cable or cradle and Windows Mobile Device Center free from the Microsoft website htto www microsoft com windowsphone en us howto wp6 sync installing wmdc aspx 2 Make sure Bluetooth is enabled on your PDA 3 Download SocketScan 10 software http Awww socketmobile com support downloads data collection series7 ss10 Click on the link for the exe file SocketScan 10 Tutorial Feedback Software amp Drivers SocketScan 10 Release Notes txt SocketScan 12 0 MB SocketScan 10 is a scanner keyboard wedge that provides basic scanner connection management exe transferring scanned barcodes to the active application running on your Windows XP Vista 7 Documents pdf Windows Mobile or BlackBerry device as though they were typed directly from a keypad SocketScan 10 is designed for use with the Bluetooth Cordless Hand Scanner CHS Series 7 v3 see release notes for supported CHS models 4 Download a
54. collection series7 ss10 Click on the link for the exe file SocketScan 10 Tutorial Feedback Software amp Drivers Manuals amp Documentation Tide Description Resources SocketScan 10 Release Hotes txt SoacketScan 10 is a scanner keyboard wedge that provides basic scanner connection management transferring scanned barcodes to the active application running on your Windows PY Vistas Documents pdf Windows Mobile or BlackBerry device as though they were typed directly fram a keypad SoacketScan 10 is designed for use with the Bluetooth Cordless Hand Scanner CHS Series 7 w3 see release notes for supported CHS models 2 Download and run the installation file e For Internet Explorer in the Security Warning screens click Run fale Download Security Warning Do you want to run or save this file Name SocketScanlOSetup exe Type Application 4 55MB From ftp socketmobile com Bun Save Cancel While files from the Internet can be useful this file type can potentially harm your computer IF you do not trust the source do not run or save this software What s the risk e For Firefox click Save File In the Downloads list double click on the SocketScan10Setup exe file In the warning screen click OK UPENNE SUCke scan USETIp exe You have chosen to open SocketScan10Setup exe which is a Binary File From ftp FEp socketmobile cor Would you like to sawe this File C s
55. configuring COM port keyboard wedge task tray icon and VIN mode e Scanner settings Utility lets you view Bluetooth properties battery level adjust beep LED vibrate settings test barcodes and more e About Software version information Task Tray Icon When SocketScan 10 is running an icon that indicates the CHS connection status will appear in the task tray in the Today screen INT CHS not connected N CHS connected Basic Scanner Information Cr You can only view Basic Scanner Properties when the CHS is connected to your PDA To TIP view more detailed scanner properties use Scanner Settings 1 Tap on the CHS icon in the task tray In the pop up menu tap Socket CHS 2 Ascreen will appear displaying basic information about your CHS including the Bluetooth friendly name scanner type firmware and battery level ro SocketScan 10 Scanner name Socket CHS OF73E9 Scanner type CHS Scanner Firmware Jg 1709 0Gl92010 Battery 100 3 After viewing the information click OK to exit SocketScan 10 Settings F You can only view Basic Scanner Properties when the CHS is connected to your SoMo TIP 1 Tap on the CHS icon or IN in the task tray In the pop up menu tap SocketScan settings r SocketScan 10 ey d Thursday 5 55 PM December 09 27010 ip Wi Fi Off 3 On 2 Jap here to set owner information i WAN No card detected Slot Enabled No tasks No upcoming appointmen
56. d by two beeps Click OK socketScan 10 48 10 After several seconds the CHS will reconnect to the computer indicated by a beep CF The CHS will beep once when it has connected and is ready to scan barcodes TIP The LED will also blink blue once every 3 seconds A CHS icon IN will also appear in the system tray 11 Click X to close Socket EZ Pair The CHS Registration screen will appear Complete the required fields and click Register Now to register the scanner or click Skip Registration to register later Ed Register Socket CHS Scanner Please take a moment to register your CHS Scanner By registering your scanner you will be eligible to receive update notifications and product information Please include the name a of the application you will be scanning data into Fields in red and marked with are required Email Application Name Industry Select Industry Where Purchased Number of units deploying I gt Select Units j Do you make purchasing decisions O Yes No Company First Name E Last Name Country Select Country Register Now Skip Registration Ready CHAPTER 5 SETUP FOR WINDOWS PC 49 To 1 50 scan barcodes Make sure the CHS is connected to the computer indicated by the CHS icon f in the system tray Open your application Place the cursor where you want to enter data Press the t
57. d that you deliver the product to Socket or to an authorized Socket Service Center The returned product must be accompanied by a return material authorization RMA number issued by Socket or by a Socket Service Center If you ship the product you must use the original container or equivalent and you must pay the shipping charges to Socket Socket will pay surface shipping charges back to any location in the contiguous United States This warranty applies only to the original retail purchaser and is not transferable Socket may at its option replace or repair the product with new or reconditioned parts and the returned product becomes property of Socket Socket warrants the repaired or replaced products to be free from defects in material or workmanship for ninety 90 days after the return shipping date or for the remainder of the original warranty period whichever is greater This warranty does not cover the repair or replacement of products damaged by abuse accident lost products use beyond Socket s published specifications liquid immersion misuse or misapplication damages caused by an act of God nor as a result of service or modification other than by Socket unless specifically described by Socket in product documentation This warranty does not provide coverage for any product updates for example updates due to design changes except as deemed necessary by Socket and does not cover any calibration or adjustments necessary for product
58. der ET Docket 93 62 FCC 96 326 Federal Communications Commission FCC August 1996 Radiocommunications Electromagnetic Radiation Human Exposure Standard 1999 Australian Communications Authority ACA May 1999 APPENDIX B SAFETY AND USAGE TIPS 95 APPENDIX C BARCODE LABEL SPECIFICATIONS All barcode symbols labels should satisfy the appropriate AIM Uniform Symbology Specification Background Substrate The barcode symbol should be printed on material media that is reflective and has a matte not glossy finish A background diffuse reflectance of at least 70 to 80 is desirable for optimum contrast Retro reflective media should be used to obtain decode distances greater than 36 inches Ink Color and Type The inked bars should not exceed 25 reflectance at the wavelength that is being used for reading whether printed with black ink or colored ink The reflectance value should not vary more than 5 within the same character Voids and Specks The code should be printed clearly free of voids specks blemishes and lines that could fool the scanner Specks or blemishes in the white spaces or false or missing bar sections could be interpreted by the reading equipment as part of the code Generally the width of such flaws is more serious than the height Code symbols labels should be rejected if these defects are present Definition The bars in the barcode symbol should be well defined Their edges should not be rough
59. ear with an empty field 3 After a few seconds the CHS will connect to Scanner Settings and beep once Your CHS will appear in the list Make sure your CHS is selected and tap Properties Scanner Settings 4 After the utility has read you scanner settings the General properties screen will appear reporting the B uetooth friendly name B uetooth Device Address Type of device firmware version and battery level If desired tap in the Name field to change the B uetooth friendly name of the CHS Bluetooth Address O00 ib OF 7 3 e9 Type CHS Scanner Firmware Version 3 2 0 1709 08192010 General Configuration Symbologies 5 Tap on the Configuration tab If desired modify how the CHS confirms a good scan and or select a data suffix to automatically add to each instance of scanned data Scanner Settings Scan confirmation Good scan beep E C OFF food scan Flash a ON O OFF Vibrate mode ON o OFF Enable Data Suffix i 4opend 4 Carriage Return lt ER C3 4opend a TAB character Selected Character Configuration Symbologies 6 Tap on the Symbologies tab to modify which symbologies the CHS will be able to decode Scanner Settings Bookland Ean C Chinese 2 of 5 Codabar Code 11 Code 39 Code 39 Extended _ Code 39 Trioptic _ Code 93 Code 128 Ean 8 Ean 13 Ean 128 _ Gs1 Databar General Configuration Symbologies Enabling all possi
60. econds and a Keyboard icon will appear next to the CHS listing Bluetooth settings Discoverable Make device discoverable Enhanced Stereo Improved battery life and MP3 audio quality for supporting devices Scan for devices Bluetooth devices Socket CHS OF3C Connected to hid CHAPTER 4 SETUP FOR ANDROID 23 To scan barcodes 1 Open your application Place the cursor where you want to enter data 2 Press the trigger button to scan a barcode Make sure the aiming beam extends across the entire width of the barcode iii TU l l TOL wil aul ru For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen F After decoding the barcode and sending it to the phone tablet by default the CHS TIP will beep once and vibrate the LED will flash green and the beam will turn off You can use Command Barcodes to modify the beep LED vibrate settings F By default a carriage return is applied after scanned barcode data is entered To TIP disable the automatic carriage return you can use the Command Barcodes use the Data Editing barcode for disabling suffixes F If no data is read in a few seconds the beam will turn off and you must try again TIP To Disconnect To disconnect turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns
61. econnection from CHS default Configures the CHS to automatically initiate a connection to the last paired HFNBO1 2650H computer device after the CHS is powered on DISABLE Automatic Reconnection from CHS Configures the CHS to wait for a computer device to initiate a Bluetooth HFNBO1 26104 connection after the CHS Is powered on After scanning the Enable Disable Automatic Reconnection from CHS command barcode A above power off and power on the CHS to make sure it is configured properly Factory Defaults Factory Reset Configures the CHS to revert all settings to factory defaults The CHS will power HFNBOOFO off after scanning this barcode Data Suffix For HID Mode Data As Is Configures the CHS to return only the decoded data i e FNBOOFSOBCEO408FFSFO0EE 01 EBOOO0O0 no prefix or suffix Suffix Carriage Return default Configures the CHS to add a carriage return after decoded ll I YADA T AN WNIT ON HFN BOOFSOD CEO4A08FFSFO0E EOI EBO1 680000008 data Suffix Carriage Return amp Line Feed Configures the CHS to add a carriage return and line feed i lil HN A AAT A WA AAA A OUN HFN BOOFSOFCEO408FFSFOOEEOI EBOS6S0064040000 8 after decoded data Suffix Tab Configures the CHS to add a tab after decoded data FNBOOFSOD C60408F F SFOOEE OT EBO1 68090000H 100 APPENDIX F COMMAND BARCODES Data Suffix For SPP or iOS Mode Data As Is Default Configures the CHS to
62. et CHS 0C7831 Scanner Info Scanner Settings About Close Switch Application 2 In the Scanner Info screen some basic properties of your CHS are displayed If desired click in the Scanner Name field to change the B uetooth friendly name of your CHS After making any changes click Menu Save SocketScan 10 Connected Scanner Scanner Name Socket CHS 0C7831 Scanner Type CHS Scanner Firmware 3 3 0 1783 02232011 Battery Level 99 Scanner Settings Cr You can configure scanner settings only when the CHS is connected to your TIP smartphone 1 In SocketScan 10 click Menu Scanner Settings The CHS will disconnect from SocketScan 10 and beep twice 2 If prompted to connect to Socket CHS click Yes The CHS will connect to Scanner Settings and beep once 88 General Scanner Info CF You can view Scanner info only when the CHS is connected to your TIP smartphone 1 In SocketScan Settings you can access Scanner Info by clicking on the main screen Scanner Settings Socket CHS OF3C4F 2 Besides viewing general scanner properties you can also place the cursor in the Scanner Name field to change the Bluetooth friendly name of your CHS After making any changes click Menu Save General Scanner Name sjocket CHS OF3C4F Battery Level 70 Switch Application Full Menu Scanner Settings Configuration 1 In Scanner Settings click Menu Configuration Enter the appropriate settings v En
63. etic Compatibility for Industrial Process Measurement and Control Equipment Part 4 Electrical Fast Transients Requirements LASER DEVICE The following statement is required to comply with US and international regulations Caution Use of controls adjustments or performance of procedures other than those specified herein may result in hazardous laser light exposure e Complies with 21CFR1040 10 and 1040 11 except for deviations pursuant to Laser Notice No 50 dated June 24 2007 e Complies with IEC60825 1 2001 08 e Class 2 laser scanners use a low power visible light diode As with any very bright light source such as the sun the user should avoid staring directly into the light beam Momentary exposure to a Class 2 laser is not known to be harmful 118 A laser warning label such as the one below appears on the scanner Example of Class 2 Laser Warning Label Battery Warning e Your device contains a rechargeable NiMH battery Never throw the battery into a fire as that could cause the battery to explode e Never short circuit the battery by bringing the terminals in contact with another metal object This could cause personal injury or a fire and could also damage the battery e Never dispose of used battery with other ordinary solid wastes Batteries contain toxic substances e Dispose of used battery in accordance with the prevailing community regulations that apply to the disposal of batteries Cover the metal terminal
64. following two conditions 1 this device may not cause interference and 2 this devic e must accept any interference including interference that may cause undesired operation of t he device Le pr sent appareil est conforme aux CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en compromettre le fonctionnem ent This equipment is also ETS EN300 328 2 ETS EN301 489 1 and ETS EN301 489 17 compliant These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his or her own expense This equipment generates and radiates radio frequency energy To comply with FCC RF exposure compliance requirements the following antenna installation and device operating configurations must be satisfied 1 Users are not permitted to make changes or modify
65. fter installation a dialog will confirm successful installation Click OK Synchronizing with a Desktop PC Refer to your BlackBerry Desktop Manager manual for complete instructions 1 Insert the SocketScan 10 installation CD into the CD drive of your computer It should auto run f the CD does not auto run use My Computer or File Explorer to access your CD drive and click on setup exe 2 In the Getting Started with SocketScan 10 wizard click on the Installation link on the left side Scroll down to the section for BlackBerry and click Install 3 Download and run the installation file e Internet Explorer In the Security Warning screen click Run When asked if you want to run the file click Run Do you want to run or save this file Name SocketScanlOSetup exe Type Application 4 55MB From ftp socketmobile com re RS While files from the Internet can be useful this file type can potentially harm your computer IF you do not trust the source do not run or save this software What s the risk e Firefox Click Save File In the Downloads list double click SocketScan10Setup exe In the warning screen click OK You have chosen to open P SocketScan10Setup exe which is a Binary File From Feo Ftp socketrmobile corm Would vou like to save this File Cancel e Chrome Click Save at the bottom of the screen Click on the link for SocketScan10Setup exe In the Security Warning screen click Run
66. functionality This warranty does not cover refurbishing cosmetic damages such as scratched paint cases or LED screens This warranty is void if you install batteries into the product that were not supplied by Socket SOCKET MOBILE IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM BREACH OF ANY EXPRESS OR IMPLIED WARRANTY INCLUDING DAMAGE TO PROPERTY AND TO THE EXTENT PERMITTED BY LAW DAMAGES FOR PERSONAL INJURY THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states do not allow limitation of implied warranties or the exclusion or limitation of incidental or consequential damages so that the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state This product may contain fully tested recycled parts warranted as if new For warranty information please visit http support socketmobile com DISCLAIMER EXCEPT TO THE EXTENT EXPRESSLY WARRANTED BY SOCKET MOBILE INC THIS PRODUCT IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE EXCEPT TO THE EXTENT REQUIRED BY LAW SOCKET MOBILE DOES NOT ASSUME ANY PRODUCT LIABILITY ARISING OUT OF OR IN CONNECTION WITH THE APPLICATION OR USE OF ANY PRODUC
67. h green and the aiming beam will turn off To modify the beep LED vibrate settings use the Scanner Settings utility or Command Barcodes F To configure an automatic Carriage Return or Tab after each scan of data use the TIP Scanner Settings utility or Command Barcodes F If no data is read in a few seconds the aiming beam will turn off and you must try TIP again To Disconnect To disconnect turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off Automatic Reconnection After you power on the CHS it will automatically try to connect to the last device it paired and connected to Make sure your device is in range with Bluetooth enabled and SocketScan 10 is running If the CHS is connected to your device and gets disconnected it will try to reconnect for a few minutes Make sure the device is on and in range and SocketScan 10 is running If 6 SETUP FOR WINDOWS MOBILE 71 the CHS cannot reconnect you will hear a long beep Press the trigger button to restart the reconnection process The CHS can only be paired with one device at a time To use the CHS witha Tip different device see Appendix G for unpairing instructions SOCKETSCAN 10 SPECIAL FEATURES SPP Mope ONLY SocketScan 10 software offers a variety of special features e Basic scanner information Quick view of basic scanner properties e SocketScan 10 settings Utility for
68. he Bluetooth search as Socket CHS xxxxxx where the TIP characters in brackets are the last 6 characters of the Bluetooth Device Address BDA which is printed on a label inside the battery compartment 5 If a pop up appears touch Pair with this device If prompted for a passkey enter 0000 four zeroes CF7 Only phones running Bluetooth 2 0 will prompt for a passkey TIP 6 Touch Home D Menu Settings Language amp keyboard or Locale amp text Make sure SocketScan 10 is selected Select locale Select language and region Text settings SocketScan 10 SocketScan 10 settings SocketScan 10 Swype SWwYy pe settings Touch Input Touch Input settings CHAPTER 4 SETUP FOR ANDROID 2 7 Open SocketScan 10 SE For some devices the icon will appear on the Home screen For other devices touch Menu to access the Apps or Programs list 8 A message will tell you to enable SocketScan 10 as your input method Touch Back S S m Please enable SocketScan 10 Please enable SocketScan 10 as Input Method by using the Input Method menu 9 Touch Menu Input Method No device connected Socket EZ Pair Input Method Settings About 28 10 Make sure SocketScan 10 is selected Touch Back 5 S m G SocketScan 10 11 Touch Menu Socket EZ Pair No device connected Input Method Socket EZ Pair Settings 12 Touch Bluetooth o use Socket EZ Pair please select the method Us
69. ill appear as Socket CHS xxxxxx The characters in Tip brackets are the last six characters of the CHS Bluetooth Device Address BDA which is labeled inside the battery compartment C7 To identify your type of Bluetooth stack click Start Right click on My Computer Tip and click Properties Hardware tab Device Manager and identify the manufacturer of your Bluetooth device 38 Bluetooth Connection Instructions Stack Microsoft 1 Right click on the Bluetooth icon amp in the system tray notification area In Windows the pop up menu click Add a Device A device search will begin 7 Add a Device lt Allow a Device to Connect Show Bluetooth Devices Send a File Receive a File Join a Personal Area Network Open Settings Remove Irnan 2 In the device list select Socket CHS xxxxxx and click Next 3 If prompted select Enter the device s pairing code Enter the passkey 0000 four zeroes Click Next Select a paling Option Create a pairing code for me Th device have a beypad ge ema i 4 Enter the device s pairing code Socket CHS fu DFFCEH Tha Savile cirmi wih d pir my ECE Check ior one on the device ca in the deke mikra Pair without using a code This type of device voch as a moue does not require et ie pinn bear Ber ciri L DEE rie Bee ins i hinia Genie Follow the remaining screens to complete the wizard Microsoft Right click on the Bluetooth icon 3 in the system tray no
70. ing Bluetooth pre paired scanner orks with all scanner models Using on screen barcode CHS TXI TCI and FDI series only Scan this barcode to put your scanner in SPP mode works only for TCi and TDi U N A CHAPTER 4 SETUP FOR ANDROID 29 13 Touch 1D Scanner x i Xi 3 47 PM o use Socket EZ Pair please select your type of scanner 1D Scanner models CHS 7E 7M 7P 7NRx 7C or 7Ci 1D Scanner 2D Scanner models CHS 7X 7XRx 7Xi or 7XiRx 2D Scanner 13 In the list of paired devices touch Socket CHS When notified of a pairing request swipe the notification down Touch Pairing request Touch Pair Cr The CHS will beep once when it has connected and is ready to scan barcodes TIP The LED will also blink blue once every 3 seconds and the icon at the top of the screen will also change Status Bar Icon CHS not connected CHS connected 14 Touch Back 5 to close Socket EZ Pair oO 15 A Socket registration icon will appear at the top of the screen Swipe the icon down to open the scanner registration software 16 Follow the instructions to register the scanner or touch Cancel to register later DSt G gt 4 58 em Register Scanner O Register Socket fa Scanner Please take a moment to register your CHS Scanner By registering your scanner you will be eligible to receive update notifications and product information Please include the name of the application you will be scanning
71. it doesn t appear correctly POSSIBLE REASONS SOLUTION This release of SocketScan 10 does not Use your device in Portrait mode and upgrade your support landscape mode for Windows SocketScan 10 software when a later release is available Mobile SYMPTOM The CHS won t work with my device running Windows Phone 7 POSSIBLE REASONS SOLUTION Windows Phone 7 devices do not support Unless Microsoft adds HID or SPP support to Windows Bluetooth HID or SPP connections For a list Phone 7 you will need to use a different device with of supported B uetooth profiles on the CHS Windows Phone 7 visit http support microsoft com kb 2449475 TROUBLESHOOTING FOR ANDROID OS SYMPTOM The CHS won t reconnect to my Samsung Galaxy or Dell Streak any more POSSIBLE REASON SOLUTION This is a known issue for Bluetooth for Disable and enable Bluetooth on your Android device and these devices try again TROUBLESHOOTING FOR BLACKBERRY SYMPTOM When I perform a Bluetooth device search the CHS does not appear in the found devices list POSSIBLE REASON SOLUTION You are using the BlackBerry Storm 9530 Upgrade your BlackBerry OS to version 5 00 714 or later or other smartphone with BlackBerry OS version previous to 5 00 714 SYMPTOM When I try to connect the CHS an error message says that SocketScan 10 can t connect to unknown device POSSIBLE REASON SOLUTION The CHS is already paired to another device Unpair the CHS
72. ix 1 IMPORTANT If using Windows 7 or Vista make sure you are running SocketScan 10 software with administrative privileges Right click on the SocketScan 10 desktop shortcut icon In the pop up menu click Properties Click Advanced Select Run as administrator and click OK Advanced Properties Choose the advanced properties you want for this shortcut Run as administrator This option allows you to run this shortcut as an administrator while protecting your computer from unauthorized activity Run in separate memory space 2 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high The LED blinks blue once per second to show that the Bluetooth radio is on but not TIP connected 3 Scan this barcode to change the CHS to SPP mode Afterwards the CHS will beep 3 times FNBOOF40000 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen 4 Turn on Bluetooth 3 on your computer Refer to your computer s documentation for instructions 5 Follow the correct instructions for your Bluetooth stack to pair with the CHS see next page CHAPTER 5 SETUP FOR WINDOWS PC 45 Bluetooth Connection Instructions Stack Microsoft 1 Right click on the Bluetooth icon 3 in the system tray notification area In Windows 7 the pop up menu click Add a Device A
73. k the B uetooth or Wi Fi signal completely APPENDIX A SPECIFICATIONS 93 94 APPENDIX B SAFETY AND USAGE TIPS Scanning Tips Practice to determine the best scanning distance for your type of barcode Scanning Distance e The best scanning distance varies depending on barcode size symbology label media W N Ratio and scan angle Check the Decode Zone in Appendix D Decode Zone to determine the proper distance between the scanner and barcode e The larger the barcode the further away you should position the scanner e The tighter the bars of the barcode the closer you should position the scanner About Bluetooth and Health Bluetooth wireless technology allows you to use short range radio signals to connect a variety of devices such as barcode scanners mobile phones Pocket PCs notebook computers printers LAN access points and many other devices at home or work These radio signals replace the cables that have traditionally connected these devices Bluetooth products have small radio transmitters and receivers Output power is normally very low only 15 75 mW This gives a working range of approximately 10 meters The maximum exposure levels from B uetooth products are far below recommended safety guidelines At most typical B uetooth devices 15 75 mW reach only one percent of the prescribed safety levels Product Care e Do not expose your product to liquid moisture or extreme humidity e Do not expose your product
74. le s entire liability and your exclusive remedy shall be at Socket Mobile s option either a return of the price paid or b replacement of the 115 Software which does not meet Socket Mobile s limited warranty and which is returned to Socket with a copy of your receipt Any replacement Software will be warranted for the remainder of the original warranty period or 30 days whichever is longer These remedies are not available outside of the United States of America Socket Mobile disclaims all other warranties either express or implied including but not limited to implied warranties of merchantability and fitness for a particular purpose with respect to the Software and the accompanying written materials This limited warranty gives you specific legal rights You may have others which vary from state to state Controlling Law and Severability This License will be governed by and construed in accordance with the laws of the United States and the State of California This License shall not be governed by the United Nations Convention on Contracts for the International Sale of Goods the application of which is expressly excluded If for any reason a court of competent jurisdiction finds any provision or portion thereof to be unenforceable the remainder of this License shall continue in full force and effect 8 Complete Agreement This License constitutes the entire agreement between the parties with respect to the use of SocketScan Softwa
75. le the scanner to restart the reconnection process CHAPTER 3 SETUP FOR APPLE IOS 19 TIP TIP 20 The CHS can only be paired with one device at a time To use the CHS witha different device see Appendix G for unpairing instructions To configure symbology support beeps LED vibrate and other scanner features use the ScannerSettings application available on Apple App Store at http itunes apple com us app scannersettings id456055932 mt 8 4 SETUP FOR ANDROID This chapter explains how to install and use the Bluetooth Cordless Hand Scanner CHS with a Bluetooth enabled device running Android 2 1 and later For the latest list of compatible devices please refer to the CHS Compatibility Checker available online at http www socketmobile com CompatibilityChecker Before you begin the instructions in this chapter make sure you have installed the batteries and tether if desired and charged the scanner as described in Chapter 2 Scanner Setup CONNECTION OPTIONS For Android OS the CHS offers two different connection options Bluetooth Mode HID No SocketScan 10 software installatio Limited configuration options needed Limited to printable ASCII and some non Instruction printable characters s on next Less efficient data communications for page barcodes containing lots of data Compatible only with Android 2 2 and later devices with support for HID Peripheral devices SPP Many configuration options
76. ll beep once TIP and vibrate the LED will flash green and the beam will turn off You can use the Command Barcodes to modify the beep LED vibrate settings By default a carriage return is applied after scanned barcode data is entered To TIP disable the automatic carriage return you can use the Command Barcodes use the Data Editing barcode for disabling suffixes CF If no data is read in a few seconds the aiming beam will turn off and you must try TIP again To Disconnect Turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off Automatic Reconnection After you power on the CHS it will automatically try to connect to the last computer it paired and connected to Make sure your computer is in range with Bluetooth enabled If the CHS is connected to your computer and gets disconnected it will try to reconnect for a few minutes Make sure the computer is on and in range If the CHS cannot reconnect you will hear a long beep Turn off the CHS and then turn it back on to restart the reconnection process ea The CHS can only be paired with one device at a time To use the CHS witha TIP different device see Appendix G for unpairing instructions CHAPTER 5 SETUP FOR WINDOWS PC 41 OPTION 2 USING THE CHS IN SPP MODE To install SocketScan 10 software and configure a COM port 1 Download http www socketmobile com support downloads data
77. m In the device list select Socket CHS xxxxxx Click Next 5 If a passkey is requested enter 0000 four zeroes Click OK 6 Follow the remaining screens to complete the wizard Broadcom Widcomm Click on the Bluetooth icon Q in the system tray notification area On the left side under Bluetooth Tasks click Add a Bluetooth Device A device search will begin Bluetooth Tasks Vem View My Bluetooth services H View devices in range E View or modify configuration In the device list select Socket CHS xxxxxx If a passkey is requested enter 0000 four zeroes Click Pair Now If prompted to select a Bluetooth service select the CHS Click Finish Use Bluetooth v2 1 or later for best results Do not use Quick Connect Bluetooth serial devices when the CHS is in HID mode CF Only computers running Bluetooth 2 0 will prompt for a passkey TIP The CHS will beep once when it has connected and is ready to scan barcodes Tip The LED will also blink blue once every 3 seconds 40 To scan barcodes 1 Open your application Place the cursor where you want to enter data 2 Press the trigger button to scan a barcode Make sure the aiming beam extends across the entire width of the barcode For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen CF After data is read and sent to the computer by default the CHS wi
78. nd run the installation file e For Internet Explorer in the Security Warning screens click Run Do you want to run or save this file Name SocketScanlOSetup exe Type Application 4 55MB From ftp socketmobile com an J Save Cancel T potentially harm your computer IF you do not trust the source do noat run or save this software What s the risk 0 While files from the Internet can be useful this file type can bd e For Firefox click Save File In the Downloads list double click on the SocketScan10Setup exe file In the Open Executable File screen click OK 6 SETUP FOR WINDOWS MOBILE 63 Opening socketscan OSetup exe You have chosen to open SocketScan10Setup exe which is 4 Binary File From Feo Ftp socketmabile corn Would you like to save this File C severie DY cancel e For Chrome click Save at the bottom of the screen Click on the link for the SocketScan10Setup exe file In the Security Warning screen click Run This type of File can harm your computer Are vou su CT save A Save Discard WoL Wank bo download SocketScanlOSetup exe 5 The installation wizard will launch Follow it to install software for Windows Mobile Sockrisoan 10 inaasa ara Wirkoome bo ihe inatalShield Wira bn Sockascan 10 64 6 Your computer will instruct you to check your mobile device for additional installation steps Click OK In the last screen of the wizard click Finish
79. ndition The barcode symbology may be disabled or Enable the symbology If you are using the CHS in SPP mode not supported by the CHS use the symbology selector feature of SocketScan software If you are using the CHS in HID mode please refer to the SocketScan Advanced Programming Guide for instructions If you do not know the symbology of the barcode and the CHS works in SPP mode for your computer device you can use the Scanner Settings utility to test scanning the barcode and determine its symbology You don t have an application open to Open an application e g a spreadsheet Place the cursor scan data into where you want to enter data Try scanning again SYMPTOM My computer device cannot find the CHS and or I get an error message saying that there are connection problems POSSIBLE REASONS SOLUTION The computer device is too far from the Move the devices closer together within a range of 10 15 m p CHS The CHS is not powered on Power on the CHS You are using the CHS in SPP mode and Remove any settings that assign another device as your have assigned another device as your default Bluetooth serial device default Bluetooth serial device Your computer device does not have Enable Bluetooth on your computer device and make sure the Bluetooth enabled and or the Bluetooth Bluetooth software is running software is not running The CHS is already paired with another Unpair the CHS See Appendix F for instructions
80. ng 1 Power on the CHS 2 While pressing the trigger button briefly press and release the power button 3 After about 15 seconds the CHS will beep Release the trigger button If you performed the actions correctly the CHS will beep 5 times and power off 4 The next time you power on the CHS it will take longer than normal After the CHS finishes powering on it will have factory default settings HID mode for Keyboards Unpairing the CHS It is possible to use the CHS with various devices however the CHS can only be paired to one device at a time If your CHS is paired to one device and you would like to pair to a different device it will be necessary to UNPAIR before you can re pair 1 Power on the CHS 2 Press and hold down the trigger button Press and hold down the power button until you hear 3 beeps 3 After you hear 3 beeps release both buttons The CHS will unpair and automatically power off The next time you power on the CHS it will be discoverable 104 APPENDIX G SPECIAL BUTTON SEQUENCES APPENDIX H CAB INSTALLATION Advanced Users Only For Windows Mobile you can install SocketScan 10 software directly from a CAB cabinet file instead of using the installation wizard A CAB file contains all the software and drivers needed to install your product on a particular Pocket PC platform CAB files are available in the SocketScan 10 installation CD in the CABs folder and coming soon online at htt
81. nged the CHS mode use the appropriate command barcode to change it back to HID mode for Keyboard devices Se i 3 On the status bar tap Bluetooth pee Mleclia Games Sheet To Go Slideshow To Go Video Chat 7 SETUP FOR BLACKBERRY 19 4 Make sure Bluetooth is turned ON Tap Add New Device Bluetooth Bluetooth Connectivity Discoverable Paired Devices No Bluetooth devices are paired Properties 5 Tap Search Add New Device arch for a device of listen for adevice to find me 6 In the list of found devices select Socket CHS 7 After they have paired and connected the CHS will beep once 80 To scan barcodes 1 Open your application Place the cursor where you want to enter data 2 Press the trigger button to scan a barcode Make sure the aiming beam extends across the entire width of the barcode For example try scanning the following barcode TIP ABCDE12345 After decoding the barcode and sending it to the tablet by default the CHS will beep once and vibrate the LED will flash green and the aiming beam will turn off You can use Command Barcodes to modify the beep LED vibrate settings By default a carriage return is applied after scanned barcode data is entered To disable the automatic carriage return you can use the Command Barcodes use the Data Editing barcode for Data As Is If no data is read in a few seconds the beam will turn off and you must
82. nowledges a HFABO1 19040001 0001 007800464 HEN EO 1 S0400071 OOO0007S004e H Vibrate after Decoding Data default HFM BOT 310001 0001 OOF 400008 HEN EO 270001 OOO0 Vibrate after computer device acknowledges a HFA BOT 31 00020001 01 2COO00 HEREC 27 000200008 successful scan default VIN Vehicle Identification Number Prefix Removal For HID Mode Only Scan to Enable Scan to Disable Return only the last 17 characters of a Code 39 HFHMBO1 3700014 HENEOT 370000 barcode 102 APPENDIX F COMMAND BARCODES Apple iOS Onscreen Keyboard For HID Mode Only Scan to Enable Scan to Disable With Beep when onscreen keyboard appears Double press CHS power button to HFN BO S4 05000000000000000000 access onscreen keyboard of Apple device HFHMB OT S400000000000000000000 4 default with No Beep when onscreen keyboard appears ll AAA HFNBO1 3401 OOOO00000000000000 Data Mode For SPP Mode Only Packet Mode defau t Configures the CHS to transmit decoded data in packet format HFNBO134014 Raw Mode Configures the CHS to transmit decoded data in raw unpacketed format I Ih DO NOT scan this barcode in iOS mode HFNE013400 H i The data mode command barcodes are for SPP mode only DO NOT scan them in iOS or HID mode APPENDIX F COMMAND BARCODES 103 APPENDIX G SPECIAL BUTTON SEQUENCES Restoring Factory Defaults To restore the CHS to its factory defaults do the followi
83. off Automatic Reconnection After you power on the CHS it will automatically try to connect to the last phone tablet it paired and connected to Make sure your phone tablet is in range with Bluetooth enabled If the CHS is connected to your phone tablet and gets disconnected it will try to reconnect for a few minutes Make sure the phone tablet is on and in range If the CHS cannot reconnect you will hear a long beep Power cycle the scanner to restart the reconnection process CF The CHS can only be paired with one device ata time To use the CHS witha TIP different device see Appendix G for unpairing instructions 24 OPTION 2 USING THE CHS IN SPP MODE To install the software 1 If you installed barcode scanning software for your phone camera scan this barcode to launch the SocketScan 10 keyboard wedge page in Google Play Alternatively you can open Google Play and search for SocketScan OF GB 4 39pm gr Productivity Q bA hh SocketScan 10 KeyboardWe Socket Mobile Description The SocketMobile SocketScan 10 keyboard wedge software enters scanned barcode data directly into any program as if the data were Version 10 0 3 6243 452KB 1 NN0 5 NNN downlnande If prompted allow the application to access Bluetooth connections and settings and or modify USB storage SD card contents e Follow the onscreen instructions to download and install SocketScan 10 software CHAPTER 4 SETUP FOR ANDROID 25 To
84. or fuzzy so that the bars and spaces have the proper widths intended for the barcode symbology used Contrast Background reflectance that of the substrate on which the codes are printed should always provide a good contrast relative to the ink reflectance that of the code bars The difference between the two should be at least 37 5 at the wavelength used for reading Tolerance The ratio of the widths of bars and spaces in a barcode symbol must conform to the appropriate AIM barcode specifications and can cause problems if not correct throughout the barcode Problems can occur when bar edges are smeared or rough or when they exhibit voids 96 APPENDIX D DECODE ZONE The decode zone for CHS 7Mi and 7Pi is shown below The minimum element width X Dimension or barcode size is the width in thousandths of an inch mils of the narrowest element bar or space in the symbol The figures shown are the typical scanning distances depths of field for selected barcode sizes The maximum usable length of a barcode symbol Width of Field at any given range is also shown In cm 20 50 8 15 38 1 Note Typical performance at 73 4 F 23 C _ on high quality symbols Pa 10 31 6 W ai A i lt d ae 5 127 h lt pe o SE 955 000WR ee e a ee cee scene cach O a ence seen secpo E a QQ S 7 i a LJ 5 127 i d 1 50 pemi o 5 50 aw k m 1 80 _2 ___ j8 00 lt 10 25 4 2 20 7 5 mil 1
85. ot use your Socket Bluetooth Cordless Hand Scanner while the plane is in the air e Do not use it on the ground without permission from the crew Radio Frequency Exposure Your Socket Bluetooth Cordless Hand Scanner contains a radio transmitter and receiver When in operation it communicates with a Bluetooth enabled mobile computer by receiving and transmitting radio frequency RF magnetic fields in the frequency range 2400 to 2483 5 MHz The output power of the radio transmitter is 15 75 mW The Socket Bluetooth Cordless Hand Scanner is designed to be in compliance with the RF exposure limits set by national authorities and international health agencies when installed or used separately from other antennas or radio transmitters Examples of RF exposure standards and guidelines ICNIRP Guidelines for limiting exposure to time varying electric magnetic and electromagnetic fields up to 300 GHz International Commission on Non lonizing Radiation Protection ICNIRP Health Physics vol 74 pp 494 533 April 1998 99 519 EC EU Council Recommendation on the limitation of exposure to the general public to electromagnetic fields 0 Hz 300 GHz Official Journal of the European Communities July 12 1999 ANSI IEEE C95 1 1992 Safety levels with respect to human exposure to radio frequency electromagnetic fields 3 kHz to 300 GHz The Institute of Electrical and Electronics Engineers Inc New York 1991 FCC Report and Or
86. oval of identification labels on the back of the product The frequency used by this product is also used by industrial scientific and medical devices such as microwave ovens as well as wireless detectors for motion detectors such as those requiring licenses used on manufacturing lines or similar radio transmitters all of these wireless devices will be called other wireless transmitters below Most modern electronic equipment e g in hospitals and cars is shielded from RF energy However certain electronic equipment is not 1 Please ensure that all medical devices used in proximity to this device meet appropriate susceptibility specifications for this type of RF energy 2 In the unlikely event that there is electronic interference between this system and other wireless transmitters quickly change the location of operation or stop operating the unit cease signal transmission 116 3 If other electrical interference or related problems occur contact Socket technical support at http support socketmobile com Radio Frequency Interference Requirements This device complies with part 15 of the FCC rules Operation is subject to the following conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This device complies with Industry Canada licence exempt RSS standard s Operation is subject to the
87. p www socketmobile com support downloads data collection series7 ss10 If you have the Socket SoMo 650 running Windows Mobile 6 Service Pack 8 or later SocketScan 10 is pre loaded on the device To install in the Today screen tap Getting Started and choose the option to install SocketScan 10 In order to install the CAB file you need a way to transfer the CAB file to your Pocket PC such as e Use Windows Mobile Device Center to transfer the CAB file to your Pocket PC e Use a memory card reader to save the CAB file from your desktop PC to a memory card then insert the memory card into your Pocket PC e If your Pocket PC has Internet access download the CAB file directly from Socket s website to your Pocket PC coming soon 1 Transfer the correct CAB file to your Pocket PC If transferring the CAB file with Windows Mobile Device Center or downloading the CAB file directly to your Pocket PC remember where you save the file 2 Tap Start Programs File Explorer 3 Use File Explorer to browse to the CAB file Tap on the CAB file 4 The CAB file will start installing on your Pocket PC Follow the instructions on your device screen to install the software 5 Your device may warn that the CAB file comes from an unknown publisher Tap Yes to continue installation 6 After software installation soft reset the device by pressing the reset button APPENDIX G SETUP FOR NOKIA E71 105 APPENDIX CONNECTION BARCODES If
88. r suspends and resumes 0000 four zeroes In the last screen click Finish Do not remove the CHS from the device list and re add it Your computer with Broadcom Widcomm Upgrade to a Broadcom Bluetooth stack using Bluetooth Bluetooth stack and Bluetooth 2 0 may 2 1 a dongle or switch to the Microsoft B uetooth stack have a broken link key with Bluetooth 2 1 or 2 0 SYMPTOM When I try to connect the CHS to the PC get an error message saying that SocketScan 10 could not open the COM port or had problems with COM port assignments POSSIBLE REASONS SOLUTION SocketScan 10 is competing with another Make sure each COM port is assigned to only one device application for the same COM port If needed use the SocketScan 10 Settings utility to assign the CHS to a different incoming Bluetooth serial COM You are running SocketScan 7 and Close SocketScan 7 and try reconnecting again SocketScan 10 simultaneously You are trying to run SocketScan 10 on Run SocketScan 10 with administrative privileges Right Windows 7 or Windows Vista in user mode click on the SocketScan 10 desktop shortcut Click Error 53 Properties Click Advanced Select Run as administrator Click OK SYMPTOM When I try to open Scanner Settings an error message says that SocketScan failed to set the scanner configuration mode POSSIBLE REASONS SOLUTION CHS is connected to Toshiba Bluetooth Ignore the message and click OK The Scanner Settings stack
89. ration Symbologies Close Switch Application 2 Select the data format as either ASCII or hexadecimal Scan a barcode The Scan Window will report the barcode s symbology data length and data content ASCII text Y 90 APPENDIX A SPECIFICATIONS The following specifications are for 1D versions of the CHS v3 Physical Characteristics Dimensions Total Weight Power Source Battery Charging Time With AC adapter 5 hours under conditions of 0 to 40 C Expected Battery Life With Normal Operation connected with Bluetooth 19 hours or 15 000 scans battery performance may vary depending on vibrate settings and work environment Environmental Characteristics Operating 32 to 122 F 0 to 50 C Temperature Storage Temperature 22 to 158 F 30 to 70 C Relative Humidity 5 to 95 non condensing Ambient Light Sunlight 10 000 ft candles 107 640 lux Artificial light 450 ft candles 4 844 lux Temperature range may vary depending on shelf life of batteries Operating System Device and Bluetooth Profile Support OS Version Compatible Devices Bluetooth Bluetooth HID SPP Support Windows Mobile 6 x v v Microsoft or Broadcom Bluetooth I i I 4 7 Vista XP Mac OS X 10 4 to 10 6 6 for Mac MacBook 4 x with Bluetooth stack v2 2 4f3 v1965 other versions not tested iOS iPod touch 5th 4th and 3 gen V v iPhone 5 4 and 3GS iPhone 3G not supported iPad mini iPad 3 generation
90. re licensed hereunder and supersedes all prior or contemporaneous understandings regarding such subject matter No amendment to or modification of this License will be binding unless in writing and signed by Socket Mobile Any translation of this License is done for local requirements and in the event of a dispute between the English and any non English versions the English version of this License shall govern Portions of SocketScan software for Android OS licensed under the Apache License Version 2 0 the License you may not use this file except in compliance with the License You may obtain a copy of the License at http Awww apache org licenses LICENSE 2 0 Unless required by applicable law or agreed to in writing software distributed under the License is distributed on an AS IS BASIS WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND either express or implied See the License for the specific language governing permissions and limitations under the License REGULATORY COMPLIANCE The Socket B uetooth Cordless Hand Scanner is designed to be compliant with the rules and regulations in locations where they are sold and will be labeled as required This product is type approved users are not required to obtain license or authorization before using This product has been certified as conforming to technological standards Therefore the following actions are punishable by law e Disassembly or modification of this product e Rem
91. return only the decoded data i e no AANA AA HFM BOOFSOBCEO408F FOFOOEE OI EBOOOO00 prefix or suffix Suffix Carriage Return Configures the CHS to add a carriage return after decoded ll MAA I WA A HFN BOOFSOD C60408F FSF O0EEOI EBO1BS0D 00008 data Suffix Tab Configures the CHS to add a fa aan ogee dare HFNBOOFSUDCEO408FFSFO0EE C1 E BOT 68090000H Suffix Carriage Return amp Line Feed Configures the CHS to add a ine CAAT TU A ANEA HENBOOFSOFCCO40SF FSF O0E EOE BOSes0D 640400008 after decoded data Power Button Double Press Key Sol Tale For HID Mode Only Scan to Enable WITH BEEP Scan to Enable WITHOUT BEEP HENEICN 30601 011 DOOOOOOOOCOCCH ENEO1 340201017 DOCOddOOCCddntt HENEICH 34060101 04000000000000H HENBOT 24020101 0400000000000 HFE 340601 2028 00000000000OH FNED1 240201 OB 00nn HFNED134A06010116000000000000H HFNBICH 340201011 6000000000000H APPENDIX F COMMAND BARCODES 101 Good Scan Indicators For HID Mode Scan to Enable Scan to Disable Beep after Decoding Data default HFNBOT 1 SUE 0001 000300750046 H HFM BOT 190E 0001000000780045 H Vibrate after Decoding Data default FHED01310001000100FA0000 FNED01 31000100004 Good Scan Indicators For SPP or iOS Mode Scan to Enable Scan to Disable Beep after decoding data default FME01190E 0001000300750045 H FNED1190E 00010000007 g0nAB H successful scan Beep after computer device ack
92. rigger button to scan a barcode Make sure the aiming beam extends across the entire width of the barcode For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen ie After decoding the barcode and sending it to the computer by default the CHS TIP will beep once and vibrate the LED will flash green and the laser will turn off You can modify the beep LED vibrate settings by using the Scanner Settings utility or Command Barcodes CF To configure an automatic Carriage Return or Tab after each scan of data use the TIP Scanner Settings utility or Command Barcodes Cr If no data is read in a few seconds the aiming beam will turn off and you must try TIP again To Disconnect Turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off Automatic Reconnection After you power on the CHS it will automatically try to connect to the last computer it paired and connected to Make sure your computer is in range with Bluetooth enabled and SocketScan 10 is running If the CHS is connected to your computer and gets disconnected it will try to reconnect for a few minutes Make sure the computer is on and in range and SocketScan 10 is running If the CHS cannot reconnect you will hear a long beep Turn off the CHS and then turn it back on to restart the reconnection process E
93. rneath the scanner to a horizontal position to unlock 2 Remove the battery cover The Bluetooth Device Address BDA is printed on a label inside the battery TIP compartment It helps you distinguish your CHS from other CHS scanners If you install SocketScan 10 you can also check the BDA in Scanner Settings Model CHS 7P E pm 8550 00039 A Revision Letter follows Part Number P N BDA 00 Bluetooth Device Address BDA gt M1111 sw 0850000233 S 10 4 If desired attach the tether to the battery cover Wrap the string loop around the inside part of the lock 5 Replace the battery cover and turn the lock to a vertical position to secure it battery types will damage the scanner Remove the batteries if the CHS will not be used for more than 30 days The red Battery Status LED will not function properly if standard AAA non WARNING Installing the batteries incorrectly may damage the scanner f WARNING Charge ONLY NiMH batteries in the CHS Charging alkaline or other TIP rechargeable batteries are being used Property Specification Battery Type NiMH rechargeable AAA Battery Life 19 hours to scan 15 000 barcodes for new fully charged batteries ASSEMBLING THE AC ADAPTER If you wish to charge the CHS with the AC adapter the correct plug for your region must be attached first Four different plugs are included Simply find the correct plug for your region and slide it into the head of the adap
94. rogram as if the data were manually typed It includes a utility for configuring Prefix Suffixes sounds symbologies and other settings Download the latest version http www socketmobile com support downloads data collection series7 ss10 Software for Bluetooth SPP mode only No software installation required for HID mode SocketScan 10 keyboard wedge software is designed for scanning 7 bit ASCII data For Unicode DoubleByte Multibyte e g for Japanese or Chinese or binary data use the SocketScan 10 SDK to convert the data before it is sent to your application Learn more about the SDK at http www socketmobile com products sdk ABOUT SOCKETSCAN 10 SDK If you are a developer who would like to add support for the CHS to your mobile application Socket offers the SocketScan 10 SDK with support for Apple iOS Android Windows and BlackBerry OS The SDK is available to members of the Socket Mobile Developer Program 19 95 year For more information please visit http developer socketmobile com ACCESSORIES Accessory SKU Number For 7Mi SKU AC4054 1381 Charging Cradle with Latch For 7Pi SKU AC4055 1382 USB A Male to DC Plug Cable SKU AC4051 1192 Car Charger SKU AC4057 1384 AC Power Supply with USB Charging Cable SKU AC4058 1415 From Taylor Made Cases Protective Carrying Case Belt Holster SKU TM HS650 KT From Viziflex Seels Waterproof Skin For 7Mi SKU SMS03 For 7Pi SKU SMS01 For
95. s Bluetooth After pairing with a device to set up a COM port tap New Outgoing Fort For other options tap and hold an existing port Incoming Port COMO New Outgoing Port Follow the screens to set up an outgoing COM port for the CHS iE Tap Start ig Programs SocketScan 10 folder SocketScan 10 IN In the Today screen tap on the SocketScan 10 icon in the task tray In the pop up menu tap SocketScan 10 Settings Make sure a COM port is selected Tap ok re SocketScan Settings Bluetooth stack Microsoft BD Address 00 14 92 05 92 49 COMO Bluetooth Port Use keyboard wedge Show icon in the task tray noscanner KE scanner connected Check one or more ports above for use by SocketScan _ Enable VIN decode 8 Tap on the SocketScan 10 icon in the task tray In the pop up menu tap Socket EZ Pair 6 SETUP FOR WINDOWS MOBILE 67 68 9 Tap 1D Scanner r SocketScan 10 To use Socket EZ Pair select scanner type 1D Scanner models CHS 7E 7M 7P 7NRx 7C or FCI 2D Scanner models CHS Ya FARS Fa or ZARE 10 Select Socket CHS and tap Pair SocketScan 10 Select a scanner From the list below to connect With SackekSean 10 on this mobile device Then tap the Pair button below IF your scanner is not listed below make sure your scanner is in SPP mode and pairing was done using the Bluetooth utility From your mobile device Refer to the Quick Start or User s
96. s described in Chapter 2 Scanner Setup For the latest compatibility information please refer to the CHS Series 7 Compatibility Checker at http www socketmobile com CompatibilityChecker CONNECTION OPTIONS For Apple iOS and Mac OS the CHS offers two different connection options For more information about HID and SPP please see Scanner Settings Bluetooth Mode HID No SocketScan 10 software Limited configuration options installation needed Limited to printable ASCII and some Instructions non printable characters on next page Less efficient data communications for barcodes containing lots of data iPhone 3G not supported iOS Apple tested and certified Compatible iOS application equivalent Many configuration options developed with SocketScan 10 SDK to SPP Broad character set including non required printable ASCII international No SocketScan 10 keyboard wedge Instructions keyboards software offered on page 58 More efficient data communications for barcodes containing lots of data CF Socket highly recommends that you use the CHS in iOS mode To learn more read our TIP white paper http www socketmobile com pdf techbrieflsocketscan 10 sdk_white paper pdf 7 The screenshots shown in this chapter may differ from your device screen TIP depending on your device type CHAPTER 3 SETUP FOR APPLE IOS 13 OPTION 1 USING THE CHS IN HID MODE To pair the CHS with your Apple device Cr You only need to pair the CHS
97. s French certain keys will represent a letter of the alphabet and additional accented characters These keys are indicated by additional dots at the top of the key To access the additional characters represented by each key 1 Touch and hold the key A menu of additional characters will appear 2 Select the accented character and the menu will close ASU X P 3 09PM http www google com gt st rca Gmail Calendar Reader More Search Sign in Preferences Google Search 36 5 SETUP FOR WINDOWS PC This chapter explains how to install and use the CHS with a Bluetooth enabled computer running Windows 8 7 Vista or XP Before you begin the instructions in this chapter make sure you have installed the batteries and charged the CHS as described in Chapter 2 CONNECTION OPTIONS For Windows the CHS offers two different connection options Bluetooth Pros Mode HID e No SocketScan 10 software installation e Limited configuration options needed e Limited to printable ASCII and some non Instructions printable characters on next e Less efficient data communications for page barcodes containing lots of data SPP e Many configuration options e Requires installation of SocketScan 10 e Broad character set including non software or application made with Instructions printable ASCII international SocketScan 10 SDK on page 19 keyboards e More efficient data communications for barcodes containing lots of data
98. s with insulating tape This is to prevent accidental short circuiting e Never expose the battery to any liquid e Always keep the battery out of reach of infants or small children e Never shock the battery by dropping it or throwing it e Dispose of a spent or damaged battery promptly Product Disposal Your device should not be placed in municipal waste Please check local regulations for disposal of electronic products 8 2013 Printed in U S A
99. scanning a barcode The Scan Window will appear 10 Scan a barcode that you would like information about The Scan Window will report the barcode s symbology data length and data in your choice of ASCII or Hexadecimal format Symbology Code 128 Data lenath 13 Data View HEX dump 0000 000C 35 59 4D 49 30 5A 34 34 55 42 51 37 55 SYNTIOZ440B070 j Close CHAPTER 5 SETUP FOR WINDOWS PC 55 56 11 After testing a barcode click Close Click OK to exit Scanner Settings The CHS will beep twice after disconnecting from Scanner Settings A few seconds later the CHS will beep once after connecting to SocketScan 10 About 1 Click on the CHS icon or in the system tray In the pop up menu click About Socket CHS OC 7831 SocketScan 10 Settings Scanner settings Socket Ef Pair aso Exit 2 The About screen will appear with SocketScan 10 version information N socket a SocketScan 10 Socket Mobile Incorporated Copyright c 2012 all nights reserved worldwide Program version 10 0 8 7825 Apr 2 2012 16 30 01 Scan4Pl version 10 0 8 7944 04022012 Visit us ak ww socketmobile cam 3 After viewing the information click OK to exit CHAPTER 5 SETUP FOR WINDOWS PC 97 6 SETUP FOR WINDOWS MOBILE This chapter explains how to install and use 1D models of the Socket Bluetooth Cordless Hand Scanner CHS Series 7
100. screen Settings Bluetooth Tap Add new device to search For other Bluetooth devices Tap on a device to modify its settings Add new device 60 7 In the device list tap on Socket CHS Settings Ek Select a Bluetooth Device Select 4 device to connect with and tap 6 Donnie s iPad Ps Socket CHS OF73E MA JLEE Cancel Ea E In the device search the CHS will appear as Socket CHS xxxxxx The characters in TIP brackets are the last six characters of the CHS Bluetooth Device Address BDA which is labeled inside the battery compartment 8 When prompted for a passcode enter 0000 four zeroes Tap Next Settings 4 Enter Passcode Enter a passcode to establish a secure connection with Socket CHS OF73E9 Press Next to continue if a passcode is not required 9 After the SoMo connects to the CHS a message will confirm the connection Tap Done Device Added Your Pocket PC has connected with Socket CHS OF 73E9 Done Fa Advanced CF The CHS will beep once when it has connected and is ready to scan barcodes TIP The LED will also blink blue once every 3 seconds 10 The CHS will now appear in the B uetooth devices list Tap ok 11 Tap X to close the Connections screen 6 SETUP FOR WINDOWS MOBILE 61 To scan barcodes 1 2 62 Open your application Place the cursor where you want to enter data Press the trigger button to scan a barcode Make
101. served worldwide Program version 10 0 0 5405 Scan4Pl version 10 0 0 5405 02262011 Visit us at way socketmobile com After viewing the information click ok to exit 6 SETUP FOR WINDOWS MOBILE 7 78 7 Setup for BlackBerry This chapter explains how to install and use the Bluetooth Cordless Hand Scanner CHS with one of the following BlackBerry devices e BlackBerry Bold 9700 Smartphone running BlackBerry OS 5 0 0 714 or later Other models have not been tested with SocketScan 10 and may require a previous software version Works in Bluetooth SPP mode only e BlackBerry PlayBook running QNX Works in Bluetooth HID mode only Before you begin the instructions in this chapter make sure you have installed the batteries and tether if desired and charged the scanner as described in Chapter 2 Scanner Setup USING THE CHS IN HID Mope BLACKBERRY PLAYBOOK Cr Compatible with BlackBerry PlayBook running QNX For BlackBerry OS TIP smartphone see page 82 for SPP instructions To pair the CHS with your Android device F You only need to pair the CHS with your PlayBook the first time you try to TIP connect 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high Cr The LED blinks blue once per second to show that the Bluetooth radio is TIP on but not connected 2 By default the CHS is in HID mode for Keyboard Devices If you cha
102. sure the aiming beam extends across the entire width of the barcode avon p venimiel aT For example try scanning the following barcode ABCDE12345 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen CF After data is read and sent to the computer by default the CHS will beep once TIP and vibrate the LED will flash green and the beam will turn off You can use the Command Barcodes to modify the beep LED vibrate settings 7 By default a carriage return is applied after scanned barcode data is entered To TIP disable the automatic carriage return you can use the Command Barcodes use the Data Editing barcode for disabling suffixes CF TIP If no data is read in a few seconds the beam will turn off and you must try again To Disconnect Turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off Automatic Reconnection After you power on the CHS it will automatically try to connect to the last device it paired and connected to Make sure your device is in range with Bluetooth enabled If the CHS is connected to your device and gets disconnected it will try to reconnect for a few minutes Make sure the device is on and in range If the CHS cannot reconnect you will hear a long beep Turn off the CHS and then turn it back on to restart the reconnection process 7 The CHS can only be paired with one devi
103. t time you try to connect TIP 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high ca The LED blinks blue once per second to show that the Bluetooth radio is on but not TIP connected 2 Scan this barcode to configure the CHS for HID mode for peripherals Afterwards the CHS will beep 3 times FNB0001000500 IMPORTANT Print out this page to scan the barcode Do not scan it onscreen The CHS must be in HID mode first before you scan the barcode above By default the CHS is in HID mode If the CHS was changed to SPP mode use the Command Barcodes to change it to HID mode 3 In the Today screen tap on the line that lists Wi Fi and Bluetooth status Start k cin Monday 12 47 PM April 13 2009 Wi Fi Off off Getting Started Tap here to set owner information No unread messages No tasks Bs No upcoming appointments Live Search Calendar Contacts Alternatively press the button on the right side of the SoMo which launches the wireless manager by default 6 SETUP FOR WINDOWS MOBILE 59 4 Use the wireless manager to enable Bluetooth Wireless Manager Bluetooth Settings ts Back Pack WAN Oo E 56x eg Connection Connections Domain Setup Enroll 7 e F Socket 10 USB to PC Wi Fi 100 6 In the Bluetooth utility tap Add new device Alternatively tap Add at the bottom of the
104. te the LED will flash green and the aiming beam will turn off You can use the Scanner Settings utility see next page or Command Barcodes to modify the beep LED vibrate settings CF To configure an automatic Carriage Return or Tab after each scan of data use the TIP scanner Settings utility see next page or Command Barcodes CF If no data is read in a few seconds the beam will turn off and you must try again TIP To Disconnect To disconnect turn off the CHS Press and hold the power button for at least 3 seconds until the CHS beeps twice high low and the blue LED turns off Automatic Reconnection After you power on the CHS it will automatically try to connect to the last phone it paired and connected to Make sure your phone is in range with Bluetooth enabled and SocketScan 10 is running If the CHS is connected to your phone and gets disconnected it will try to reconnect for a few minutes Make sure the phone is on and in range If the CHS cannot reconnect you will hear a long beep Power cycle the scanner to restart the reconnection process CF The CHS can only be paired with one device at a time To use the CHS witha TIP different device see Appendix G for unpairing instructions 7 SETUP FOR BLACKBERRY 87 SOCKETSCAN 10 SPECIAL FEATURES Scanner Info CP You can view Scanner Info only when the CHS is connected to your smartphone 1 In SocketScan 10 click Menu Scanner Info SocketScan 10 Sock
105. ter until it latches Plug in the cable making sure the USB connector is oriented the correct way sgi 38 Tip he charger cannot be sold in Japan CHAPTER 2 SCANNER SETUP 11 CHARGING THE SCANNER The CHS must be fully charged before first use Use the AC adapter to charge from a wall outlet or the USB cable to charge from a PC Initial charging takes about 5 hours with an AC adapter Optional charging accessories are also available TIP The LED will be solid red while charging and green when the batteries are full TIP Connecting the USB cable to a PC to charge the CHS is not reliable and not recommended Hardware e USB A Male to DC Plug Cable 2A maximum Optional Charging e Charging cradle Hardware e Car charger e Mobile Power Pack available in Americas Asia Pac e ACor DC adapter from Socket SoMo Purchase online at http Aww1 socketmobile com products bluetooth scanners accessories bt aspx 3 SETUP FOR APPLE IOS This chapter explains how to install and use the Socket B uetooth Cordless Hand Scanner CHS with Apple devices running iOS Made for the following Apple devices e iPod touch 5 generation Made for e iPod touch 4 generation iPod iPhone iPad e iPod touch 3 generation e iPhone 5 e iPhone 4S e iPhone 4 e iPhone 3GS e iPhone 3G e iPad mini e iPad 3 generation e iPad 2 e iPad Before you begin the instructions in this chapter make sure you have charged the CHS a
106. that the Bluetooth radio is on but not TIP connected 2 Make sure the CHS is in HID mode for Peripheral Devices First scan this barcode to change the CHS to HID mode for Peripherals UTA AL ENBOOOLOOOSOO IMPORTANT Print out this page to scan the barcode Do not scan it onscreen 3 Touch Home D Menu Settings Wireless amp networks Bluetooth settings S 4 m sH i 4 30em Wireless amp network settings Airplane mode Disable all wireless connections Wi Fi Connected to scktguest Wi Fi settings Set up amp manage wireless access points Bluetooth Bluetooth settings Manage connections set device name amp discoverability 22 1 Make sure your device has Bluetooth on and is Discoverable Touch Scan for devices ake Witi z H o 4 03pm Bluetooth settings Bluetooth Device name DROID PRO Discoverable Discoverable for 103 seconds Scan for devices Bluetooth devices 2 In the list of found devices select Socket CHS to 3 w GB 5 47 em Bluetooth settings Discoverable P Discoverable for 27 seconds Enhanced Stereo Improved battery life and MP3 audio quality for supporting devices Scan for devices Bluetooth devices T Mobile_LEO Pair with this device Socket CHS OF3C4F Pair with this device E The CHS will beep once when it has connected and is ready to scan barcodes TIP The LED will also blink blue once every 3 s
107. tification area In Windows the pop up menu click Add a Bluetooth Device Vista XP In the welcome screen check the box My device is set up and ready to be found Click Next A device search will begin E Wizard Welcome to the Add Bluetooth Device Wizard Before proceeding refer to the Bluetooth section of the device documentation Then set up your device so that your computer can find it Turn it on Make it discoverable visible Give it a name optional Press the button on the bottom of the device keyboards and mice only D Add only Bluetooth devices that you trust In the device list select Socket CHS xxxxxx Click Next If prompted select Use the passkey found in the documentation and enter the passkey 0000 four zeroes Click Next Follow the remaining screens to complete the wizard CHAPTER 5 SETUP FOR WINDOWS PC 39 Bluetooth Connection Instructions Stack Toshiba _ Double click on the Bluetooth icon amp in the system tray notification area 2 In Bluetooth Settings click New Connection 3 In the connection wizard select Express Mode Click Next A device search will begin Add New Connection Wizard Jl This wizard will create the settings for Bluetooth device connection Please ensure your Bluetooth devices are on and set to discoverable Express Mods Fiscomnenesy Custom Mode This allows you to set the details for the connection me
108. to extreme high or low temperatures e Do not expose your product to lit candles cigarettes or cigars or to open flames etc e Do not drop throw or try to bend the product as rough treatment could damage it e Do not paint your product as the paint could obstruct parts and prevent normal use e Do not attempt to disassemble your product a broken warranty seal will void the warranty The product does not contain consumer serviceable components Should your CHS need service contact Socket technical support at http support socketmobile com e Treat your product with care Keep in a clean and dust free place e Changes or modifications of this product not expressly approved by Socket may void the user s authority to operate the equipment Antenna Care Do not place a metallic shield around the Socket B uetooth Cordless Hand Scanner since it will reduce the radio transmission efficiency Efficient Use For optimum performance please make sure that there is no metal surrounding your Socket Bluetooth Cordless Hand Scanner Driving RF energy may affect some electronic systems in motor vehicles such as car stereo safety equipment etc Check with your vehicle manufacturer to be sure that the Socket B uetooth Cordless Hand Scanner will not affect the vehicle s electronics Aircraft e Turn off your Socket Bluetooth Cordless Hand Scanner before boarding any aircraft e To prevent interference with communications systems you must n
109. ts Live Search amp No unread messages Getting Started a SocketScan Settings Socket E2 Pair About Exit 2 A screen will appear displaying the SocketScan software settings as well as the Bluetooth stack manufacturer and Bluetooth Device Address SocketScan Settings E ok Bluetooth stack Microsoft BD Address 00 14 92 05 92 49 Pot Desens COMO Bluetooth Port Use keyboard wedge Show keyboard wedge icon in tray no scanner IE scanner connected Check one or more ports above For use by SocketScan C Enable YIN decode e Port Select the incoming Bluetooth serial COM port that you would like SocketScan to use to connect to the CHS REQUIRED e Use keyboard wedge Should be selected in most cases unless you plan to use the SDK e Show keyboard wedge icon in tray Select to have a task tray icon appear that conveniently indicates whether the CHS is connected to the PDA e Enable VIN decode Select to have SocketScan 10 only send a 17 character VIN i e omit any prefix suffix included in a VIN barcode 3 After making any changes tap ok to exit 6 SETUP FOR WINDOWS MOBILE 73 74 Scanner Settings gt You can access Scanner Settings only when the CHS is connected to your PDA TIP J 1 Tap on the CHS icon in the task tray In the pop up menu tap Scanner settings 2 The CHS will disconnect from SocketScan 10 indicated by two beeps The Scanner Settings screen will app
110. ttery level If desired change the Bluetooth friendly name of the CHS Scanner Properties General Configuration Symbologies Hame Bluetooth Address 00 c0 1 BOF 3229 Type CHS Scanner Firmware version 3 2 0 1709 08192010 7 Click on the Configuration tab If desired modify how the CHS confirms a good scan and or select a specific suffix to automatically add to each instance of scanned data Scanner Properties General Configuration Symbologies Scan confirmation Good scan beep Good scan flash Vibrate mode Enable Data Suttix Append a Carriage Retum lt CR gt Append a TAB character Selected Character 8 Click on the Symbologies tab to modify which symbologies the CHS will be able to decode Scanner Properties General i Configuration Symbologies C Bookland Ean C Chinese 2 of 5 C Codabar C Code 11 Code 39 C Code 39 Extended C Code 39 Trioptic C Code 93 Code 128 Eang Ean 13 Ean 128 C Gel Databar Cl Ge Databar Limited Cl Gel Databar Expanded Interleaved 2 of 5 CF Enabling all possible symbologies may slow the decoding process TIP c The RSS symbology is now known as GS1 DataBar TIP If you want to read UPC A symbols disable the GS1 DataBar option so that GS1 DataBar TIP symbols don t get mistakenly decoded 9 Click OK to exit the Scanner Properties If desired click Test to test
111. tware for any other purpose than to be used with Socket Mobile products Your rights under this License will terminate automatically without notice from Socket Mobile if you fail to comply with any term s of this License Limitation of Liability TO THE EXTENT NOT PROHIBITED BY LAW IN NO EVENT SHALL SOCKET MOBILE BE LIABLE FOR PERSONAL INJURY OR ANY INCIDENTAL SPECIAL INDIRECT OR CONSEQUENTIAL DAMAGES WHATSOEVER INCLUDING WITHOUT LIMITATION DAMAGES FOR LOSS OF PROFITS LOSS OF DATA BUSINESS INTERRUPTION OR ANY OTHER COMMERCIAL DAMAGES OR LOSSES ARISING OUT OF OR RELATED TO YOUR USE OR INABILITY TO USE SOCKETSCAN SOFTWARE HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY CONTRACT TORT OR OTHERWISE AND EVEN IF SOCKET MOBILE HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES SOME JURISDICTIONS DO NOT ALLOW THE LIMITATION OF LIABILITY FOR PERSONAL INJURY OR OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THIS LIMITATION MAY NOT APPLY TO YOU IN NO EVENT SHALL SOCKET MOBILE TOTAL LIABILITY TO YOU FOR ALL DAMAGES OTHER THAN WHAT MAYBE REQUIRED BY LAW IN CASES INVOLVING PERSONAL INJURY EXCEED THE ORIGINAL PURCHASE AMOUNT OF SOCKETSCAN SOFTWARE THE FOREGOING LIMITATIONS WILL APPLY EVEN IF THE ABOVE STATED REMEDY FAILS OF ITS ESSENTIAL PURPOSE Export Law Assurances You may not use or otherwise export or re export SocketScan Software except as authorized by United States law and the laws of the jurisdiction in which SocketScan Software was o
112. vice and then click Search Again Search Again 4 If prompted select Use the passkey found in the documentation and enter the passkey 0000 four zeroes Click Next 5 Follow the remaining screens to complete the wizard 46 Bluetooth Connection Instructions Stack Toshiba Double click on the Bluetooth icon in the system tray notification area 2 In Bluetooth Settings click New Connection In the connection wizard select Express Mode Click Next A device search will begin Add New Connection Wizard This wizard will create the settings for Bluetooth device connection Please ensure your Bluetooth devices are on and set to discoverable Obes ink Ren e O Custom Mode This allows you to set the details for the connection es In the device list select Socket CHS xxxxxx Click Next 5 If a passkey is requested enter 0000 four zeroes Click OK 6 Follow the remaining screens to complete the wizard Broadcom _ Click on the Bluetooth icon amp in the system tray notification area Widcomm On the left side under Bluetooth Tasks click Add a Bluetooth Device A device search will begin Bluetooth Tasks i a Bluetooth Device led View My Bluetooth services View devices in range E View or modify configuration In the device list select Socket CHS xxxxxx If a passkey is requested enter 0000 four zeroes Click Pair Now If prompted to select a
113. with your Apple device the first time you TIP try to connect CF By default the CHS is in HID mode for Keyboard devices If you changed the TIP CHS to a different mode refer to the Command Barcodes to change it to the correct mode 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high CF The LED blinks blue once per second to show that the Bluetooth radio is TIP on but not connected 2 Start a Bluetooth device search e iOS Tap Settings General Bluetooth Turn on Bluetooth A Bluetooth device search will begin Settings ja wr ROM N Reg Brightness amp Wallpaper Biuetocth lt ji Picture Frame ee Searching _ Mail Contacts Calendars E7 Safari e Mac OS Click System Preferences Internet amp Wireless Bluetooth In Bluetooth preferences select the On checkbox Click Set up New Device A Bluetooth device search will begin eer Bluetooth O APTA pe aJ show ait a J Eluetooth power is on mi On i Coverab Set Up New Device _ Show Bluetooth status in the menu bar N Sharing Setup A i Advanced 7 14 1 In the device list tap Socket CHS initially it will appear as Keyboard Tap Pair Settings Bluetooth ka Wi Fi ROM N Bluetooth on Devices 4 fg Brightness amp Wallpaper E Picture Frame Keyboard Ca Mall Contacts Calendars E7 Safari HSH iPod
114. y be required CF The CHS needs to be configured for iOS mode Your application may TIP have specific instructions for configuring the CHS Otherwise you can use the Command Barcode for iOS mode in Appendix E CHAPTER 3 SETUP FOR APPLE IOS 17 1 Power on the CHS Press and hold the small power button until the LED turns blue and the CHS beeps twice low high E The LED blinks blue once per second to show that the Bluetooth radio is on TIP but not connected 2 Open the CHS compatible application that you installed 3 Enable Bluetooth on the Apple device A Bluetooth device search will begin Settings Gereral i Bluetooth kel Wi Fi ROM N Kai Brightness amp Wallpaper Soe on lt s il Picture Frame Devices LJ Mail Contacts Calendars En Safari bil iPod 4 In the list of found devices select Socket CHS If prompted tap Pair 18 Settings Bluetooth Bluetooth _on 5 Devices kd Airplane Mode OFF Wi Fi sckiguest hed Notifications On iOS Socket TXI 10082A Not Connected annar E Waai i ocket TXI of Connected Mya Diacpverabke il Picture Frame L Mail Contacts Calendars Safari In the device search the CHS will appear as Socket CHS xxxxxx The characters in brackets are the last six characters of the CHS Bluetooth Device Address BDA which is labeled inside the battery compartment The CHS will beep once after it has connected and is ready
115. y try to connect to the last phone tablet it paired and connected to Make sure your phone tablet is in range with Bluetooth enabled and SocketScan 10 is running If the CHS is connected to your phone tablet and gets disconnected it will try to reconnect for a few minutes Make sure the phone tablet is on and in range and SocketScan 10 is running If the CHS cannot reconnect you will hear a long beep Power cycle the scanner to restart the reconnection process Cr The CHS can only be paired with one device at a time To use the CHS witha TIP different device see Appendix G for unpairing instructions CHAPTER 4 SETUP FOR ANDROID 31 SCANNER SETTINGS SPP MODE ONLY CF These special features only work when the CHS is connected to your Android TIP device Status Bar Icon When SocketScan 10 is running an icon that indicates the CHS connection status will appear at the top of the screen KT 1 CHS not connected IN CHS connected To open Scanner Settings In the main screen of SocketScan 10 touch Scanner Settings CF The CHS will close SocketScan 10 Keyboard wedge disconnect indicated by 2 beeps TIP high low open Scanner Settings and reconnect indicated by a beep Basic Scanner Information 1 In the main screen of Scanner Settings touch Socket CHS YON 8 539 Pw SocketScan 10 D Socket CHS OF3C4F 2 The screen will report the Bluetooth friendly name scanner type firmware version and battery level

Socket Bluetooth Cordless Hand Scanner User's Guide

Contents

Download Pdf Manuals

Related Search

Related Contents