MOjO Color“ Product User Guide
Contents
1. Color color changers require almost no maintenance However you should Keep the unit clean Disconnect the mains power supply then wipe the cover with a damp cloth Do not immerse in liquid Wipe lens clean with glass cleaner and a soft cloth Clean internal components about once a year with a light brush and vacuum cleaner Do not use alcohol or solvents Keep connections clean Disconnect electric power then wipe the DMX and audio connections with a damp cloth Make sure connections are thoroughly dry before linking equipment or supplying electric power Changing the Lamp If electrical power is supplied and the lamp does not light it may be time to change the lamp Replacing a Fuse Power Surges or inappropriate electrical power supply may cause a fuse to bum out If the fuse bums out the product will not function whatsoever If this happens replace the fuse as follows 1 Unplug the unit from electric power source 2 Insert a flat head screwdriver into a slot in the fuse cover C in figure 6 Gently pry up the fuse cover 3 Note two fuses The replacement fuse is covered The used fuse has both ends exposed Remove the used fuse If brown or unclear it is burned out 4 Push the replacement fuse out of its cover then insert the replacement fuse into the holder where the old fuse was Reinsert the fuse cover Products are packed with a replacement fuse If your replacement fuse is missing anew one can be purchase2. appliance must be earthed Product Specifications Name Mojo Color Model MOC Voltage 230V 50Hz CE Power consumption 300W Fuse T3 15A Dimensions 280x220x160 mm Weight 6 kg Lamp 24V 250W ELC GX5 3 or 24V 250W EHJ G6 35 Name Mojo Color Model MOC 150 Voltage 230V 50Hz CE Power consumption 200W Fuse 5A Dimensions 280x220x160 mm Weight 6 7 kg Lamp HTI 150W Name Mojo Color Model MOC Voltage 120V 50 60Hz Power consumption 300W Fuse T3 15A Dimensions 280x220x160 mm Weight 6 kg Lamp 24V 250W ELC GX5 3 or 24V 250W EHJ G6 35 Name Mojo Color Model MOC 150 Voltage 120V 50 60Hz Power consumption 250W Fuse 5A Dimensions 280x220x160 mm Weight 6 7kg Lamp HTI 150W Versions for other lamps may be produced Please check the specification label on your product Product specifications may be subject to change Please visit www geni com tw for details 10 Troubleshooting This troubleshooting guide is meant to help solve simple problems Ifa problem occurs carry out the steps below in sequence until a solution is found Once the unit operates properly do not carry out following steps If the effect does not operate properly refer servicing to a technician No Light No Movement All Products Response Suspect three potential problem areas the power supply the lamp the fuse 1 Power supply Check that the unit is plugged into an appropri
3. connector OUT Figure 6 12 Appendix A DMX Dip Switch Value Guide DMX products must have their own address to receive DMX signals Addresses on MOC products are set by flipping appropriate DMX dip Switches To do this you need to know that DMX dip switches have the following values 1 1 2 2 3 4 4 8 5 16 6 32 7 64 8 128 9 256 And you need to know that DMX address settings are the sum of the dip switch values For example standard DMX addresses for four MOC changer each of which has four channels Follow MOC Address Value DMX Dip Switches ON Unit 1 1 1 Unit 2 2 2 Unit 3 3 1 2 Unit 4 4 3 Explanation Since each unit has four channels each address advances four values See Address Value above Once address values are figured out add DMX dip switch values to obtain the appropriate address DMX Dip Switches ON for each unit Flip appropriate DMX dip switches on each unit 11 Mojo Color Product Guide SS GED EOD a eo copes tacts serene centre E eerie Page 1 NV INI tie dase cacicaciucl EE EA eS Page 1 Getting ROA Y 25 uc sureiosciesesinvss ida ec siatensaswsecmriiawdceaaod Page 2 Install the Lamp ELC smicessanisseaicetagrennadesivaeiwienrcaadd Page 2 Lamp Installation ELC iiicisccsicncsacissedacustansivasstapeesaes Page 2 Installing the Lamp Figure T iccciciaediiersssecsrotieoeiaevinss Page 2 Install he Lamp ERJ rissies erci Page 2 Lamp Installation EH osicasecicnnea
4. Copyright 2001 Geni Electronics Co Ltd Product specifications may be subject to change For more information please visit our web site http www geni com tw Thank you Mojo Color Product User Guide MOC MOC 150 Mojo Color One color wheel with 16 color CEN Geni Electronics Co Ltd THANK YOU Thank you for buying a Geni product For best results please carefully read and follow the directions in this product user manual Congratulations You have a great innovative product from Geni Electronics Co Ltd Geni Mojo Color changer make anyplace festive Whether you want simple plug amp play action or a sophisticated DMX show this product series has an effect for you You can rely on Geni Electronics Co Ltd for more excellent lighting products We design and manufacture strobes effects and mirrored projectors And new products are being launched regularly For information please visit our web site at http www geni com tw We work hard to keep you our customer satisfied You can get some of the best quality best priced products on the market from Geni So next time turn to Geni for more great lighting equipment Always get the best with Geni Thank you Geni Electronics Co Ltd Appendix B Back Panel IN out E A Earth Ground rower omea sen 1 B EC power connector 1N C Fuse holder D DMX signal Canon connector IN J E DMX signal Canon
5. ate power supply 2 The lamp Replace the old lamp with a newone of appropriate specifications See directions above for replacing lamps 3 The fuse Replace the fuse See directions above for replacing the fuse No Response to DMX Response Suspect the DMX dip switch setting DMX cable or connectors a controller malfunction a light effect DMX card malfunction 1 Check the DMX dip switch setting Make sure the DMX dip switch address setting is correct 2 Check the DMX cable Unplug the unit change the DMX cable resupply electrical power Try your DMX control again 3 Determine whetherthe controller or light effect is at fault Does the controller operate other DMX products properly If not take the controller in for repair If so take the DMX cable and the light effect toa qualified technician No Response to Audio 1 Check the function setting of the first unit Make sure that function dip switch 1 is on Function dip switch 1 on audio control 2 Turn UD the music volume Getting Ready All Geni products are thoroughly tested at the factory and shipped in perfect condition If damage has occurred during shipping or if components are missing please contact your Geni dealer immediately Your package should include 1 One Mojo Color color changer with bracket 2 One IEC electric mains power cord with plug 3 One product user manual The lamp may or may not be included depending on your GENI dealer In m
6. d at an electric appliance store Be sure to use a fuse of the same type and specification See the product specification label for details Function Dip Switch Chart Dip OFF Mode 1 Single unit show mode 2 Single unit audio mode 3 Single unit audio mode ON Mode Single unit audio show mode 4 unit audio show mode master Self test mode 4 Single unit audio mode Single slow show mode 5 Single unit audio mode Focus assistance 6 1 unit audio mixed show Audio low BPM show mode 7 1 unit audio mixed show Audio high BPM show mode 8 Single unit audio mode No program 9 Single unit audio mode No program Applies only when audio mode Func dip switch on is activated Otherwise these channels are DMX address setting dip switches Mojo Color DMX Channel Chart CH1 Colors 209 255 160 208 150 159 16 140 149 15 130 139 14 120 129 13 110 119 12 100 109 11 90 99 10 80 89 9 70 79 8 60 69 7 50 59 6 00 O 40 49 5 30 39 4 20 29 3 10 19 2 0 9 Shutter 1 RO OO 00000OO0SDSOSCOC Strobe 1 flash per 4 seconds to 4fps Rotation slow fast Four color Square White amp Green Pink amp White amp Blue Blue amp White amp Green White amp Yellow Red amp White amp Orange Pink Circle Blue Circle Light Blue Circle Orange Circle Green Circle Yellow Circle Dark Green Circle Red Circle White Circle 0 Light unit automatically s
7. huts off 5 seconds later 7 Set Up and Operation The set up and operation of all Mojo Color color changers is similar The main difference is that function channels of various items vary so that dip switch settings differ slightly Follow directions below as they pertain to your particular product and your preferred operation mode Before plugging unit in always make sure that the power supply matches the product specification voltage Do not attempt to operate a 120V specification product on 230V power or vice versa One unit Audio 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp fastened onto the Mojo Color bracket Leave at least one meter on all sides for air circulation 2 Flip on Func dip switch and dip switch 1 3 Plug one end of the electric mains power cord into the IEC socket on the unit See figure 6 page 12 Then plug the other end of the cord into a proper electric power supply socket 4 Turn on the music The scanner will change to the music Four unit Audio 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp bolted onto the Mojo Color bracket Leave at least one meter on all sides for air circulation 2 Link the units as shown in figure 4 page 5 Connect a DMX signal cable from the first unit s DMX out socket to the second unit s in socket Repeat this process to link the second third and fourth units 3 Acti
8. instructions Do not touch the lamp bulb glass See Figure 2 Oil on hands shortens the lamp life If you touch the bulb glass wipe off the glass with a clean lint free towel and rubbing alcohol 3 Glove your hand before installing the lamp Hold the lamp socket with one hand Insert the lamp pins into the holes in the lamp socket 4 Make sure that the lever is up Slide the lamp into the lamp base 5 Put on the lamp cover and fasten the screws snugly Remarks To replace the lamp using a small flat head screw driver to push thelamp outofthe lamp socket Lamp Items Lamp Socket Lamp Reflecto Lamp Flat head screw driver Figure 2 Install the Lamp MOC 150 MOC 150 usethe HTI150W lamp by Osram only Lamp Installation MOC 150 1 Make sure the unit is un plugged in advance Loosen the screws on the upper cover with a flat screwdriver open the upper cover 2 Use fingers to loosen screwA B C in sequence Hold on to screwA C and pull backward See Figure 3 3 Hold on the tube with gloved right hand The tube will be catapulted by pressing the lever D backward with left hand 4 Repeat procedure 1 amp 2 before installing the tube Insert the pins of tube into the bottom of socket E Note The small hole is on lever D side 5 After installing the tube tighten up screwA amp C simultaneously next tighten up screw B Lock up the upper cover to get jobs done Figure 3 Maintenance Mojo
9. ost cases the lamp is not included Install the Lamp ELC Mojo Color color changer use either the GX5 3 24V 250W lamp by Osram or the ELC lamp of identical specifications by Philips Use only the appropriate lamp for your unit Note that product versions that use other lamps may be offered in the future Check your product specification label for information Lamp Installation ELC 1 Loosen the two screws on the top of the lamp cover Open the case 2 Read lamp instructions Do not touch the lamp bulb glass See Figure 1 Oil on hands shortens the lamp life If you touch the bulb glass wipe off the glass with a clean lint free towel and rubbing alcohol 3 Hold the lamp socket with one hand Insert the lamp pins into the holes in the lamp socket 4 Make sure that the lever is up Slide the lamp into the lamp base 5 Put on the lamp cover and fasten the screws snugly Lamp Items A Lever B ELC Lamp C Lamp Base D Lamp Socket E Lamp Pins Figure 1 linstall the Lamp EHJ Mojo Color use either the HLX 64655 24V 250W lamp by Osram or the EHJ lamp of identical specifications by Philips Use only the appropriate lamp for your unit Note that product versions that use other lamps may be offered in the future Check your product specification label for information 2 Lamp Installation EHJ 1 Loosen the two screws on the top of the lamp cover Open the case 2 Read lamp
10. re 6 c0sceeeaes Page 12 The lamp for MOC differs from that of MOC 150 beides this all other features between are the same In this manual all features description of MOC alos applies to MOC 150 Description Mojo Color Small color changer with high output great effect instant audio shows and DMX control Mojo Color One color wheel with 16 colors The set up control and functions of various Mojo Color may differ Please refer to specific product headings in this manual Warning Like all electronic products Mojo Color changer lights must be used with common safety precautions in mind e Mojo Color color changer lights contain no user serviceable parts Refer servicing to qualified technicians only e Disconnect from electric mains power supply before removing covers or changing lamps Keep case closed while operating Do not insert objects into air vents e Keep away from flames and flammable material Keep away from liquids Never operate in rain or in damp conditions e If effect lights are dropped or struck disconnect mains power supply immediately Have a qualified engineer inspect for safety before operating e Lamp and metal become hot during operation Allow time to cool before handling Do not touch lamp bulb glass with bare hands e Read user manual instructions thoroughly before operating Follow the instructions Never remove warning or informative labels from the unit eT his
11. rom the first unit s DMX out socket to the second unit s in socket Repeat this process to link following units 3 Set DMX dip switches as follows MOC Dip ON Unit 1 1 Unit 2 2 Unit 3 1 2 Unit 4 3 For more units continue to use standard DMX dip switch settings See Appendix A for details 4 On the last in a series of units flip on the Terminate dip switch Term dip switch This keeps the signal clear Make sure other function dip switches are off 5 Supply electric power Plug electric mains power cords into each unit s IEC socket see figure 6 then plug the other end of the mains power cord into proper electric power supply sockets Do so for all units and the controller DMX Set Up DMX OUT 4100S Hnes pree pases O Unit 1 Note Link all DMX cables and set dip switches before con necting electric power DMX Controller Figure 5 Do not supply power before the whole system is set up and connected properly 6 Design your show according to your DMX controller functions DMX channel functions are shown on pages 7 Product Operation Overview In audio mode Func dip switch on choose various shows by flipping regular dip switches on the first unit For example for a slow four unit audio show flip on Func dip switch on the first unit to activate audio mode then flip regular dip switches 2 and 6 on to acti
12. vate a slow paced four unit audio show See the following Function Channel Chart Do not activate audio dip switches on following units but set their DMX channels according to regular DMX procedures See Appendix A for an introduction to DMX dip switch settings One final note Terminate all systems by flipping on the Term dip switch on the last unit This preserves clear signal transmission in both audio and DMX modes
13. vate audio control On the first unit flip on Func dip switch Terminate the system On the last unit flip on Term dip switch 4 Set DMX dip switches as follows MOC Dip ON Unit 1 A 2 Unit 2 2 Unit 3 Unit 4 1 2 3 5 Supply electric power Plug electric mains power cords into each unit s IEC socket see figure 6 then plug the other end of the mains powercord into proper electric power supply sockets starting with the first unit Do not supply power before the whole system is set up and connected Properly Four unit Audio Set Up DMX OUT DMX IN DMX OUT Y ay Wea Note Link cables and set dip switches before connecting electric power Figure 4 6 Turn on the music Note that up to 64 units can be connected and operated in audio mode To do so flip on DMX dip switch 1 on the 5th 9th 13th etc unit Then repeat settings on following units so 6th 10th 14th etc unit DMX settings unit 2 settings 7th 11th 15th etc Unit DMX settings unit 3 settings 8th 12th 16th unit settings unit 4 settings DMX Control 1 Fasten the effect light onto firm trussing Use a 30 kg rated or stronger C clamp bolted onto the Mojo Color bracket Leave at least one meter on all sides for air circulation 2 Link the units as shown in Figure 5 Plug a DMX signal cable from the controller to the first unit s DMX in socket Then plug a DMX signal cable f
14. velevernass Kerntoeng ia Page 3 installing the Lamp Figure 2 icc issccnceiestitcccavedacsceccor Page 3 Install the Lamp CA Tics icrvatiievevacteaitivetaeasuxasinss Page 3 Lamp Installation HT ciiiescisavineiaveseeieraess E Page 3 Installing the Lamp Figure Bic isviaceissccccisareeenseinisceess Page 3 Set Up and OSH tae fiz sin saanensseyinsdarderecbbiisadedincnuasa Page 4 One unitAu dio BMG CE e ceisiai ei Page 4 Four nit AUG Ossessione nii erisa aa Page 4 Four unit Audio Set Up Figure 4 ccc cee eeee es Page 5 DMX SOMO arises Page 5 DMX Set Up Figure 5 oc rrecseescscissoennrrdarmiiertavvecueeseute Page 6 Product Operation OvervieW ssssssssrsrsrsrsrsrsrere Page 6 Function Dip Switch Chart css ssa Scnnarerencacsngeveatvoneronss Page 7 DMX Channel CMa ie Gopccenestassenscccasdencensisensscavacneesad Page 7 WANAUE TANCE vo casecocccdehancagctodacses DE AEE E nE EE ENEE Page 8 Changing the LAM cu sdcnnccideuditenuveaosmidansatyretenenanans Page 8 Replacing the FUSG ccceceeceeneeeeeeeeeaeeenenseeaees Page 8 WROUDISSHOOUING seniri renari nne a aea aa Page 9 No Light No Movement All Products Page 9 No Response to DMX s ssnssssnsrnsrsrrsrsrrresrnrrsreene Page 9 No Response to AudioO sssnsisisrsrsrsrrrerrrirrsrsrsenne Page 9 Product SpecificationS ssssssssirisrsisrsrsrrrrrerrene Page 10 Appendix A DMX Dip Switch Value Guide Page 11 Appendix B Back Panel Figu
Download Pdf Manuals
Related Search