Installation Instructions and User Guide
Contents
1. Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Commissioning Testing the System With the front cover removed ensure the black purge shower switch inside the base is switched to purge This enables water to flow without the pump running which is necessary in the following commissioning process Fit the front cover using the 3 fixing screws Push the temperature control knob onto the spindle with the marker pointing to the 12 o clock position Connect the shower hose to the unit but do not fit the handset Turn on the hot and cold isolating valves and the electricity isolating switch Place the open end of the hose in the bath or shower tray Set the temperature control knob to fully cold marker at 6 o clock position and press the stop start button The pump will not operate but the water should run Cold water will run from the hose and you should allow this to continue for two minutes after which the control knob should be returned to the 12 o clock position Allow the water to run for a few minutes to stabilise the hot water flow Turn off the electricity at the isolating switch and remove the knob and cover Switch the black purge shower switch to shower and refit the cover and knob ensuring the marker on the knob points to the 12 o clock position Turn on the electricity at the isolating switch Pass the hose through the hole in t2. mode grip the bezel of the handset and turn in either direction Cleaning Rub clean feature To remove any build up of limescale from your handset remove it from its holder and rub your fingers over the rubber spray jets Turn the shower on and any build up of limescale will be flushed out of the handset MA STOP START 3 g Vil VA PUGA HUM Gh LM OTS HM Gt op COEGt SG Aap thor te yi Jn ie 7 Ko t t r HGS VARENNA EY Me LAA LOM 0 Zt 44 WL yt ee Apt lL pU YU Wey te MILO MY 4f AEA CL AMY nh lta LEC gA DY IL hl py ARL AI yg VILE TE 007 WY VY ty I Ed 1 hyyl 7 PETES LO LIUUYLG bE sl rt Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors 11 Troubleshooting A Warning Before carrying out general repairs or testing the shower ensure that the electricity supply is turned off at the mains and the correct circuit fuse is removed Symptom Likely Cause Action Remedy Pump not operating but water is flowing Purge shower switch switched to purge Isolate electrical supply remove cover and switch to shower Pump not operating and no water is flowing No electricity supply to unit Check all fuses and electrical supply Pump operates but no water is lowing No water supply to unit Check isolating valves are turned on Check cold water storage tank has not run dry Poor performance Restrict
3. BRISTAN Installation Instructions and User Guide Thermostatic Power Shower 1000 Please keep this booklet for future reference Installer when you have read these instructions please ensure you leave them with the user Contents Important safety Information eeceeceeeeeeeeeeeteeneeeeten 3 Prod ct feat reS weicssseeremacinsesbow niianalesiieyblaeadunsndvalasbdayaiioentad 4 Electrical requirements ieee 5 Water requirements ceresensnsnennsnnnnnnni ainiai 6 Fitting yor SHOWER oonan 7 Fitting the riser Tailess reiia ER 9 Commissioning testing the System 0 Operating the SHOWEP eccctevenudveleseesusuedisucnuemeedats 1 Adjusting the showerhead cccccccscceeeeceeceeeeeteeneeenteeaes 1 Cleaning amp maintenanCEsscensnsnsinansnsiriaa 1 Troubles Noli ecosuuanu ike 2 Se E L E E A E E A E E Macias 3 G afanteE ia E E RE E 4 S E a e E E E E A E A 4 2 Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Important Safety Information e Please read these instructions thoroughly and retain for future use e All products manufactured and supplied by Bristan are safe provided they are installed used correctly and receive regular maintenance in accordance with these instructions e f you are in any doubt what so ever about your ability to install this product safely you must employ the services of an experienced qualified plumber e Do not operate the shower unit
4. Shower Refit unit to pipes and secure to wall using 32mm x No 8 screws provided Connect the wire which may be coloured Brown or Red to the terminal marked L Connect the wire which may be coloured Black or Blue to the terminal marked N Connect the wire which may be coloured Yellow Green to the terminal marked E Secure into position with the cable clamp and tighten the two fixing screws Do not fit the front cover at this stage refer to the commissioning procedure Note If the electrical supply cable is concealed in the wall ensure that it avoids the unit s fixing points so that fixing screws do not pierce the cable Wall fixing points Cable Clamp Cable Connector Electrical connections 8 Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Fitting the Riser Rail Fitting the Riser Rail Before proceeding with fitting the rail identify each of the items supplied using the illustration on your right The Slider 1 should not be removed from the rail 2 during fitting The top of the slider has a smooth profile whereas the underside has a recess revealing th
5. ature to 38 40 C with the control knob pointing to 12 o clock if the stored hot water is at the recommended 60 C PURGE Cha SHOWER m Purge shower Switch Temperature adjustment 10 Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Operating the Shower To operate the shower ensure th approximately to the 12 o clock e temperature control knob is set position and press the stop start button 1 For a hotter shower turn the control knob anti clockwise for a cooler shower turn it clockwise The handset holder has a friction grip on the rail and simply slides up and down to adjust the height The angle of the handset can also be adjusted The handshower has three shower modes which are selected by rotating the bezel around the spray head Cleaning Do not at anytime use bath cleaning liquids powders or specified scratch cleaners on any surface finishes In order to avoid surface wear or chemical attack on any of your shower fittings when cleaning always use a damp cloth For persistent stains or marks you may use domestic liquid or soap Handset The Handset has three spray modes 1 Spray 2 Massage 3 Combination To select the desired showering
6. ce may not correspond with the coloured markings identifying the terminals in your switch please follow the procedure below Please use the cable entry point provided Failure to comply will eliminate any BEAB approval Procedure The wire which is coloured Blue or Black must be connected to the terminal that is marked with the letter N The wire which is coloured Brown or Red must be connected to the terminal that is marked with the letter L The wire which is coloured Green or Yellow must be connected to the terminal that is marked with the earth symbol The installation and wiring must comply with I E E regulations Double Pole Switch 228mm wide Mains Supply Typical Power Shower Installation Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Shower Rail 660mm High 275mm wide Water Requirements Under no circumstances must the Power Shower be connected to the mains cold water supply or to a combination hot water system For correct operation of the Bristan 1000 Power Shower both hot and cold supplies to the unit must be gravity fed at equal pressures rom a cold water storage tank and hot water storage cylinder We recommend a minimum 112 litre 25 gallons cold water storage ank Please ensure compliance with all Water Regulations Please ensure maximu
7. d or damaged Modification or repair of this product by person s not authorised by Bristan will invalidate this guarantee This guarantee does not affect your statutory rights Service Policy Replacement Parts Policy Important In the event of product or component malfunction DO NOT tamper with or remove the product from site Telephone the Customer Services Department and be prepared with the date of purchase model number and a clear description of the complaint Our service staff are fully qualified to advise on correct installation procedures and will be able to diagnose whether the fault will require a replacement part or a visit from a Bristan engineer If required a service call will be booked and either yourself or an appointed representative who should be a person of 18 years or over must be present during the visit All site visits to product within the guarantee period will be carried out free of any parts or labour charges provided the conditions of the guarantee have been adhered to the second year guarantee is parts only All site visits to product out of guarantee will be subject to charges for parts and labour Charges will also be levied on cancelled appointments unless advised to Bristan at least 24 hours in advance of the agreed date and time Should a product be discontinued spare parts stocks will be maintained but in the event of a part becoming unavailable Bristan reserve the right to
8. e grooves on the handset holder Fit the soap dish 3 onto the bottom end of the rail and secure using the small screw from the kit Position the rail on the wall bearing in mind the different heights of people likely to use the shower and the length of the hose when connected to the shower and passed through the retaining hole in the soap dish Mark the wall to indicate the upper fixing screw position N Warning Please check for any hidden pipes and cables before 1 drilling holes in the wall Drill the wall at the marked fixing position using a 6mm drill to a depth of 35mm push the plugs 4 supplied into the hole and loosely fix the rail end using the screw supplied 5 checking that the rail is hanging vertically using the spirit level incorporated into the top end of the rail The bubble should be exactly between the two lines on the spirit level body Mark the position for the lower fixing screw move the rail to one side drill the wall and fix the lower end of the rail Check that the rail is perfectly vertical and tighten both fixing screws Slide the end cap 6 into position on the top end of the rail and fit the screw cover 7 into the recess in the soap dish When fitting the hose it should pass through the larger hole of the soap dish Note The hose nut and not the handset handle fits into the slider The slider moves more freely on the rail if gripped next to the rail rather than at the handset
9. eed help Give us a call on 0844 701 6273 and speak to one of our trained advisors Fitting your Shower Fitting the Shower We recommend that the shower unit is fitted at chest height and set to one side of the intended riser rail position ensuring that the position of the shower handset when positioned on the wall is at least 1 metre below the cold water storage tank Important The unit must be fitted on the finished tiled surface Warning Do not seal the edge of the shower unit to the tiled surface with any form of sealant The gap between the back of the shower unit and the tiles is needed for ventilation The outlet connection for the hose should be sited at the bottom of the unit Do not fit a fuse or switch on mains electrical supply until all plumbing work is completed Connecting pipework can feed from above or below the unit or straight through the wall at nominal centres of 40mm Top Feed Hot on the right cold on the left Bottom Feed Hot on the left cold on the right Back Feed Hot on the bottom cold on the top Procedure The integral fittings on the valve are of the self seal push fit type Ensure that all burrs are removed from the ends of the supply pipes Where chromium plated pipe is used then the first 25mm of chrome must be roughened or removed to ensure that the push fit fittings in he supply retain the pipe in position The inlet elbows supplied are of a standard length in some cases h
10. ese will need to be shortened for correct installation Flush out the supply pipes to ensure that no debris enters the unit Cut the inlet elbows to the required length Locate the inlet elbows into the mixer valve inlets by pushing firmly hrough the rubber grommets until pipe stop is felt Hold the unit on the wall and mark the pipe work to the appropriate length Cut the pipes and remove all burrs Push the unit and elbows firmly onto the pipes until the stop is felt Mark the fixing points for the unit Release unit from pipes by pressing the colletts on the elbow fittings and pulling the unit off the pipe work A Warning Please check for any hidden pipes and cables before drilling holes in the wall Drill the wall and insert the appropriate wall fixings Bring a supply cable to conform to E E regulations from the switch to the unit position The cable can enter the unit from the rear or via channels in the base of the unit and the bottom or the right hand side Feed the supply cable in to the unit but do not connect Reduce Elbow to 63mm Reduce Elbow to 86mm Top Feed Reduce Elbow to 86mm Reduce Elbow to 63mm rT Bottom Feed Reduce Elbow to 63mm Pipe cover Back Feed For chrome plated pipes l remove the first 25mm of plating 4 Collett Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors 7 Fitting your
11. he front of the soap dish and refit the handset Your shower is now ready to run Press the stop start button on the front cover to operate the shower which will work as a power shower It is intended that the temperature knob aligned to the 12 o clock position you should get a comfortable shower temperature If however the shower is too hot or cold remove the control knob and adjust the brass spindle anti clockwise to increase the temperature clockwise to decrease When the desired shower temperature is achieved replace the knob with the marker pointing to the 12 o clock position Temperature Adjustment The valve allows the maximum showering temperature to be set at a safe level preventing accidental scalding This setting should be made during commissioning and will require that the hot water cylinder is at its normal operating temperature IMPORTANT The handset must be in the spray mode We recommend the reading of User Instructions before proceeding further This will familiarise you with the operation of the shower Turn the brass mixer valve spindle fully clockwise and then anti clockwise until the black line on the spindle is aligned with the groove on the mixer body and fit the control knob in the fully cold position Check that it is correctly fitted by turning fully clockwise to the stop pull the knob off and check that the black line and groove are aligned Adjust if necessary This sets the shower temper
12. highest standards Guarantee 2 Year parts 1 Year labour subject to registration This guarantee applies to products purchased within the United Kingdom or Republic of Ireland but does not apply to products used commercially This is provided that The guarantee registration card is completed and returned within ten days complete with a copy of proof of purchase Proof of purchase is required for any servicing requirements 2 The product is installed and operated in accordance with our instructions and has not been misused or damaged This in no way affects your statutory rights as a consumer The information on the Guarantee card helps Bristan to process any claims and contact you about your product and its maintenance if required The registration of your personal details is purely for Bristan use and the remaining information helps us to make products for the future Should a complaint arise products are guaranteed against faulty workmanship and materials for a period of 12 months from the date of purchase when in domestic use second year guarantee is parts only For your guarantee to be valid your shower must be installed by a competent person in accordance with the instruction manual Bristan will repair or replace at our option free of charge any faulty components during the guarantee period provided it has been maintained and operated in accordance with our instructions and has not been misuse
13. ies To empty the pipe work open the hot and cold water taps Make your connection into the hot water supply pipe from the cylinder ensuring that it is the first draw off below the expansion pipe tee to minimise the effects of water draw offs elsewhere in the house and a minimum of 1 metre from the base of the cold storage ank and the top of the hot water cylinder f this is not possible a direct connection must be made from the hot water cylinder with a cylinder flange The cold water supply should be taken directly from the cold storage ank and must be positioned 60mm below the cold feed connection o the hot water cylinder This should not be directly beneath the ball valve as aeration of the water going to the shower could cause pump damage Run hot and cold pipe work to the unit position ama o connection Cold feed to hot water cylinder connection 60mm to the Power Shower Water tank detail Cold Water i _ Storage Tank 1m minimum Isolating Valves minimum Mains Water Supply Bath spillover I 1 3 level Minimum 25mm i a between Shower 1 I head and i spillover lt j Shower tray spillover level Typical Power Shower Installation E 51mm Cylinder Flange 6 N
14. if you suspect it is frozen Do not site the shower unit where it might be subjected to freezing conditions e Do not operate the shower unit if the showerhead or spray hose has been damaged or is blocked e Do not block the flow of water from the showerhead by placing it smothering it on your hand or any other part of your body or foreign object e Do not operate the shower if the water stops flowing during use or if the water is leaking from the shower unit itself General Safety e Always switch off the power at the consumer unit and remove the correct circuit fuse before making any electrical connections or if you have to remove the cover of an installed unit e The unit must be mounted on the finished wall surface usually tiled Under no circumstances must you tile up to the unit after fixing it directly to the bare wall as this may cause overheating e f the shower unit is fitted in a hard water area a scale inhibitor may have to be fitted and the filter cleaned regularly BEAB Approved BEAB British Electrotechnical Approvals Board approval of safety Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Product Features 1 Push Button STOP START Switch Stop Starr 4 Electronic switch 2 Temperature Control Adjustable Temperature Control 3 Hose outlet Shower hose outlet Removing cover 1 Temperature Control Knob 2 Screws x3 Please n
15. ions in water supply Pump may have overheated Unit may be incorrectly installed Check both hot and cold isolating valves are fully open Allow unit to cool and retry Check that the top of the shower handset is at least 1 metre below the base of the cold water tank Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Spare Parts 1 2 13 11 No Part No Description No Off 01 SP 087 0603 Base assembly 02 SP 087 0514 Stop start button 03 SP 087 0505 Temperature control knob 04 SP 087 0608 Front cover 05 SP 087 0014 Front cover screws 3 06 SP 087 0230 Solenoid 07 SP 087 0155 Mixer valve assembly 08 SP 087 0211 Purge shower rocker switch 09 SP 087 0127 Pipe connection 0 SP 087 0110 Pump unit 1 SP 087 0068 Pipe cover 2 SP 086 0061 Long inlet elbow 2 3 SP 087 0035 Motor cover 4 SP 280 0024 Rail end cap 5 SP 280 0100 Spirit rail and slider assembly 6 SP 280 0033 Soap dish 7 SP 285 0820 ose 8 SP 168 0204 andshower Please define colour Not shown 14 15 16 Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors 13 Guarantee Guarantee Thank you for purchasing a Bristan product This product has been designed and tested in the UK to the
16. m supply head of 10 metres minimum 1 metre to the shower head when positioned on the wall t is recommended that the hot water supply is at a temperature of 60 C in line with British Standard 6700 British Water Regulations and Plumbing Code of Practice Do not use jointing compounds or solder within 300mm of the unit Before proceeding with the installation of this unit check that your site requirements allow the shower unit when positioned on the wall to be a minimum of 1 metre below the bottom of the cold water storage tank All plumbing should be completed before any electrical connections are undertaken The unit can be connected to a combination cylinder system providing it has cold water storage capacity of 112 litres 25 gallons When connecting pipe work avoid using elbows sweep or formed bends will ensure optimum performance Do not run pump dry as this will damage the internal seals and invalidate the warranty All pipe work to the unit should be 15mm Non restrictive isolating valves must be fitted on hot and cold supply pipes Do not position unit in areas subjected to freezing conditions The temperature of your stored water must not exceed 65 C A stored water temperature of 60 C is considered sufficient to meet all normal requirements in line with the British Standard 6700 Warning All connecting pipe work should be earthed Procedure Plumbing Connections Isolate mains water and electrical suppl
17. ote that this product comes packaged with the front cover and control knob already in place These have to be removed to install the shower Please follow the procedure below Pull off control knob 1 Remove all three fixing screws 2 The cover can now be slowly removed care should be taken not to strain wiring which is attached to the front cover This procedure can be reversed to replace the front cover and control knob after installation to the wall 4 Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Electrical Requirements N Warning This appliance MUST be earthed All electrical wiring for the shower must comply with the current E E Regulations which includes earth cross bonding to all metal pipe work Important All plumbing connections should be completed before any electrical connections are undertaken The shower must be connected to a 230 240 volt A C electrical supply from a 13 amp ring main via a fused double pole switch with at least 3mm contact separation The switch is to be clearly identifiable but out of reach of a person using a fixed tap or shower i e mounted in an adjacent room It should be fused at no more than 3 amps This appliance must be earthed and all associated metal pipe work earth crossbonded in line with current I E E regulations As the colours of the wires in the cable not supplied used to connect to this applian
18. supply a substitute of equal quality For spare parts please contact Customer Services or via the Bristan website Opening times Please refer to the Bristan website Customer Service Tel 0844 7016273 Fax 0844 7016275 E mail enquirefabristan com 14 Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Need help Give us a call on 0844 701 6273 and speak to one of our trained advisors Issue POW SHX 1000 D3 BRISTAN Bristan Group Ltd Birch Coppice Business Park Dordon Tamworth Staffordshire B78 1SG Web www bristan com Email enquire dbristan com A Masco Company
Download Pdf Manuals
Related Search