User guide Billi Eco
Contents
1. Periodic replacement of your Bill Eco Filter Cartridge is necessary to maintain he cleanliness of your drinking water Billi recommends a filter replacement every 6 months A replacement filter change service is available If you wish to install he replacement filter cartridges yourself your Billi representative will provide genuine Billi replacement filter cartridge sets Billi Filter Cartridges Reduces amp Removal Filter Change Due Monitor The Eco filter change due monitor operates by counting the number of cups dispensed and the number of days elapsed until a pre set evel is reached Once reached the yellow ilter icon as pictured above will turn on The Eco will continue to operate while the ilter indicator is flashing Water filters installed in areas with higher levels of sediment will experience a reduced service ife It may be necessary to change filters before the change filter indicator flashes particularly dirty water is noticed coming hrough the water supply e g from other ap ware immediately place your Billi Eco into Holiday Mode by pressing the Pressure Relief button This will help prevent premature blocking of the filter cartridges Filter Order Taste Fluoride Expected Type PartNo Suits Micr Filters Sediment Chlorine VOCs Chemicals Odour Minerals Life Prem 990413 BilliEco sub Single v v v v v Slight bal months Stand 990402 BilliEco 5 Single v y v v v calg months User guid2. intended c if the defect occurs wholly or partially as a result of any act or omission by the customer or any person other than Billi if the product is subject to misuse neglect accident or abuse or the customer continues to use the product after the defect becomes apparent e if the product is damaged as a result of poor water quality f if the product is repaired or any attempt to repair the product is made by anyone other than an authorised repairer of the products acting at Billi s direction or g if the product is altered or modified in any way unless such modification has been approved in writing by Billi 2 Notwithstanding anything to the contrary filters are not covered by this or any other Product Warranty b d User guide Billi Eco Limitation of liabilitv 3 Except for the Product Warrantv set out above and except for anv liabilitv in connection with the supplv of goods imposed on Billi bv the Trade Practices Act 1974 Cth and other similar state and territorv legislation including for breach of implied conditions and warranties which cannot or which can only to a limited extent be lawfullv excluded all liabilitv of and conditions and warranties relating to the supply of the products by Billi are hereby expressly excluded Any such liability which cannot be lawfully excluded is limited at Billi s option to any one or more of the following a the replacement of the goo
3. period over a week Data is lost when the power is removed however learnings from he first days use is applied to the entire earning cycle so the unit will quickly resume intelligent timer operation When the self learning timer is enabled he unit will enter standby if no water is expected to be used for a 3 hour or more period The unit will shutdown completely if no water is expected to be used for a 6 hour or more period In office environments his feature will typically cause the unit to urn off outside normal business hours ie overnight and on weekends In domestic environments with no one home during working hours the unit will turn off through each weekday but may remain on at night and during weekends See page 6 for dispenser icons To activate refer to Options page 5 Standby Mode Standby operation may be optionally enabled to reduce power consumption In standby mode the hot water set point is reduced to 72 C and the cold water set point is increased to 18 C When enabled standby is invoked after two hours from the time of last use When a tap lever is pressed in standby no water is dispensed The indicators will flash to indicate the water is not ready The tap can be repressed to dispense water During Standby mode the moon amp star icon will flash See page 4 for dispenser icons To activate refer to Options page 5 Boiling water disabled mode Your Billi Eco features an additional boili
4. Billi User guide Billi Eco User guide Billi Eco Contents Warnings amp Important information General Maintenance Features and Modes Tap Options amp Operation Dispenser Icon Codes Filtration Information Changing the filter Service Support Warranty O ONO OH KF UN Warnings amp Important information For continued safety of this appliance it must be installed operated and maintained in accordance with the manufacturer s instructions Your appliance should be installed by a suitably qualified tradesperson For correct operation of this appliance it is essential to observe the instructions as outlined in this booklet Do not use this appliance with water that is microbiologically unsafe or with water of unknown quality without adequate disinfection before or after the system Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts Filter replacement must be performed at intervals of not more than 6 months Use this appliance only as directed in these instructions and only for its designed purpose This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety This appliance is not suitable in an area wher
5. ds or the supply of equivalent goods he repair of the goods the payment of the cost of replacing the goods or of acquiring equivalent goods or he payment of the cost of having the goods repaired b o d 11 Billi Billi Ptv Ltd 42 Lucknow Crescent Thomastown Victoria 3074 Australia Telephone 61 3 9469 0400 Facsimile 61 3 9469 0499 www billi com au Designed and manufactured in Australia As Billi Pty Ltd has a policy of continual improvement all details are subject to change without notice All goods are sold subject to our published terms and conditions Billi is a registered trademark 1012
6. e Blue dot Flashes when chilling On constant when chilled water ready Off when in holiday or standby mode Red amp blue dots will lash yellow if the unit goes into fault Normal operation ee O Blue A Normaal operation O Red e e e e e AU eee Operating temperatures of hot and cold water not Blue m MM vet reached Red Blue Boiling water disabled Blue System in holiday or standby mode or off Orange E M tu A Mu MM e O Red e O Orange mmm m i Unit in fault mode o User guide Billi Eco Billi Filter Cartridges The Bill Eco is fitted with single dual action filter incorporating sediment and chemical removal elements ALI Billi Eco filters are manufactured using bacteria and biofilm resistant materials for improved water quality Premium filters provide better tasting water due to the high quality carbon chemical removal filter Sub micron rated these filters have excellent chemical absorption removing or reducing chlorine volatile organic compounds VOCs chemicals tastes and odours Use only genuine filters as designed for this system All drinking water filtration systems should be flushed after a period of non use If your Billi Eco has not been used for a period of 48 hours or more operate the lever and run water for 1 minute then release the lever Replacement of Billi Filter Cartridge
7. e Billi Eco Filter removal and replacement instructions Important note Please ensure vou remove the foam packing under the filter before installing 1 Remove the front panel 2 Place the unit in Holidav Mode bv pressing the Pressure Relief button once The lights on the dispenser will alternate and then go off 3 Hold filter and swing towards you slowly The top of the filter is in a hinged cradle assembly It should stop after approximately 30 degrees of travel 4 The filter can now be released from the holding cradle by pulling down on the filter 5 Take care not to spill water in the base of the tray If so wipe gently with absorbent paper 6 Install new filter into the same location by pushing all the way up into the cradle 7 Push filter back into the unit until it locks into place Power light should come back on 8 Lift cold lever for the levered style taps or touch and hold the blue icon for the touch activated taps and run until water flow stops Close cold lever or remove your finger from the blue icon and wait for 10 minutes Lift cold lever or touch and hold again and run until water stops Close cold lever or remove your finger from the blue icon 9 Check for any leaks from around the filter hosing or pipeworks 10 Replace the front cover User guide Billi Eco Thank you for choosing to install a Billi Eco Drinking Water A
8. e a water jet could be used Children should be supervised to ensure that they do not play with the appliance DANGER The operation of the thermal cut out indicates a possibly dangerous situation Do not reset the thermal cut out until the water heater has been serviced by a suitably qualified person WARNING Do not connect any restrictor or pressure relief device to the vent pipe of this water heater if installed If the supply cord is damaged it must be replaced by the manufacturer its service agent or similarly qualified persons in order to avoid creation of a hazard User guide Billi Eco Billi hose sets as supplied with the appliance are to be used Old or other manufacturer s hose sets should not be re used If the appliance is located where the ambient air temperature could fall below 4 C when the heater is not in use do not turn off the power supplv to the appliance This safeguard does not offer the same protection to the connecting pipework and fittings The ambient temperatures this unit should operate within are 4 C to 45 C Turn off power to unit by unplugging the power cord from the power point if water supply is turned off Caution and safety Boiling water is dangerous and can cause severe burns particularly with young children Boiling water must always be handled with caution Use this appliance only as directed in these instructions and only for the purpose or which it
9. has been designed Your Billi Eco is designed to be safe and practical n an environment with young children it is recommended that the boiling water safety switch is activated The following safety features have been included Ergonomic levers Levers touch activations located safely above water outlet Smooth electronically controlled boiling water flow rate Flow is briefly reduced as water first enters cup to prevent splashing Dispenser remains cool to touch Childproof safety switch Boiling water Safety Isolation mode General Maintenance Your Billi Eco has been designed to require minimal maintenance other than replacement of filter cartridges During each filter change check all water connection fittings for signs of leakage Check all tubing for any signs of damage Check the cupboard area around the base of unit for any signs of moisture Ensure side vents of the under bench module are kept clear and airflow is not obstructed Restricted airflow will cause inefficient operation of the refrigeration system Cleaning the dispenser Your Billi Eco Dispenser is fabricated from solid zinc casting material with tough protective chrome plating Proper care of the Billi Electronic dispenser crucial Avoid using abrasive cleaners Wipe clean using a damp cloth Use of a non solvent non smearing cleaner such as Windex is recommended Do not pour water over dispenser Cupboard ventilatio
10. in Power save mode settings Ecolntelligence standby or on 24 7 The Green icons on the tap indicate the power save level that is selected To change or activate a setting once in options mode press and release the cold right lever to scroll through the following options Lightning bolt icon on indicates Eco Intelligence self learning timer is enabled Moon amp Star Icon on indicates Standby Mode is enabled Blue Icon On no green icons indicates system is in 24 hour continuous mode To save new setting and exit Options Mode press the safety switch and release Wait 10 seconds for unit to return to normal operation Holiday mode To set press the pressure relief valve located under the unit cover beside the filter housing User guide Billi Eco Dispenser Icon codes Dispenser Icon Orange dot Flashes when filter change due On constant when overdue Red lock illuminated Safety button activated To use press the indent on the back of the tap momentarily amp lift or press the boiling lever Green leaf illuminated Eco intelligence Green moon amp stars illuminated n holiday mode Red amp blue icons will not be displayed in this mode Green moon amp stars flashing n standby mode Red amp blue icons will not be displayed in this mode Red dot Flashes when heating up to temperature On constant when boiling water ready Off when in holiday or standby mod
11. n red 8 blue icons are both illuminated constantiv 2 Push both the hot and cold levers down amp then while holding the two levers down touch the safety switch indent at the back of the black panel Hold both levers and safety switch for 3 seconds Icons will flash yellow Release both the levers amp safety switch Unit is now in options mode If you wish to change or set the safety switch mode follow the safety switch settings procedure below If you wish to change or activate the power saving mode follow the power save mode settings procedure below anne w Safety Switch settings The Red padlock indicates the different safety settings enabled To change or activate a setting once in options mode as above press and release the hot left lever to scroll through the following options Red Icon Off indicates the hot tap is disabled Padlock icon on Red icon off indicates safety switch is enabled Red Icon On indicates normal operation with safety switch not enabled To save new setting and exit Options Mode touch the safety switch and release Wait 10 seconds for unit to return to normal operation To dispense boiling water once the safety switch is activated simply touch the indent on the black panel at the back of the tap You will be able to dispense boiling water for 8 seconds After 8 seconds the safety switch will automatically reactivate and the red padlock icon will appear aga
12. n requirements Your Billi Eco underbench module requires no cupboard ventilation but requires air space around the unit of 25mm Care should be taken when using the cupboard space to avoid stretching or damaging plastic pipe work Check fittings and tubing at each filter change for signs of damage or leakage Always ensure access to power switch and water supply tap is not restricted User guide Billi Eco Features and Modes Dispenser Swivel The Eco dispenser incorporates a swivel function allowing the dispenser to be swung out of the wav if more sink space is required A central position stop provides positive location during normal usage Safetv Timeout Vour Billi Eco incorporates a water deliverv Safetv Timeout to prevent an uncontrolled flow of water Water flow stops automaticallv after a set time interval Flow can be started again bv releasing and pressing the dispenser lever Boiling water timeout 10 secs Chilled water 1 minute Childproof safety switch Your Billi Eco is fitted with a childproof safety lock out feature to protect against accidental dispensing of boiling water and the risk of burns Please refer to safety switch settings on page 5 Self learning timer Ecolntelligence Your Billi Eco incorporates an energy saving self learning timer This timer earns the users behaviour over a period of time up to one month and pre empts he need for water throughout each 24 hour
13. ng water safety isolation feature Once activated delivery of boiling water becomes totally disabled Chilled water can be dispensed normally During this mode the red hot icon will remain off To activate refer to Options amp Operation Safety Switch Settings page 5 Holiday mode Holiday Mode is provided to save energy when the unit will not be used for long periods In this mode both the water chiller and water heater are disabled and the unit will use very little power Pressing the Pressure Relief button places the unit in Holiday Mode The unit will exit Holiday Mode if either the power is turned off then on or if any of the levers are pressed The Self Learning Timer will ignore user behaviour while the unit is in Holiday Mode and resume normal operation when the mode is terminated Holiday Mode is indicated by the star amp moon icon being illuminated See page 6 for icon images User guide Billi Eco Options and Operation To operate simplv press the left lever to dispense boiling water and the right lever to dispense chilled When lifted the levers will latch for continual deliverv until released with a light press Operating modes can be selected bv the user bv entering Options Mode Within the options mode vou can set the safetv switch through the hot water lever and power save mode through the cold water lever To enter the options mode 1 Turn on the unit and wait for normal operatio
14. ppliance Your Eco is manufactured to exacting standards using high quality materials and with proper maintenance and care should function for many years For information on our filtration and service contract please contact Billi Head Office on 1800 812 321 or email us at service billi com au For technical support please call 1800 812 321 and speak to one of Billi s experienced technician s To book a service call out request a filter change or please contact the Billi Service Centre on 1800 812 321 or book online at www billi com au Service Centre Filter cartridges are also available for purchase online at www billi com au Buv Filters User guide Billi Eco Warrantv Subject to the warrantv exclusions set out below if a defect in a new product supplied by Billi Pty Ltd ACN 124 066 717 Billi and purchased by you customer rom a reseller authorised by Billi occurs within 24 months of the date of purchase of he product as a result of defective materials or defective manufacture by Billi and Billi receives a written claim containing details of the product defect together with a receipt rom the reseller of the products showing the date of purchase of the products or such other proof of purchase and the date of purchase as Billi may accept within 25 months of the date of purchase Billi shall at its discretion a direct an accredited service provider to attend the customer s premises provided tha
15. t the premises are located within Australia and repair the defect free of charge but if the customer s premises are located more than 25 kilometres from one of Billi s authorised service agent s locations then the customer will be liable for any increased freight costs fees charges or levies Billi may incur as a result of fulfilling its obligations under this paragraph a of this Product Warranty or b direct the customer to return the product to Billi so that Billi may provide a replacement product free of charge If Billi elects to do this Billi will also pay the necessary freight charges and the customer will pay for the removal of the product and the costs of reinstalling the replacement product Any product replaced or repaired under this Product Warranty will be covered by the product s remaining warranty period or three months whichever is greater If the product or any part thereof is replaced by Billi under this Product Warranty all of the right title and interest in and to the replaced product or part shall vest in Billi upon it being replaced Warrantv exclusions 1 Billi shall not be liable under this Product Warranty a unless the product was installed correctly and as per the installation instructions supplied with the product if the defect is contributed to or caused by any improper usage of the product or usage of the product for purposes other than that for which the product was designed or
Download Pdf Manuals
Related Search