Installation & User Guide RIseR and non-RIseR
Contents
1. 1010 770 165 60 1000 800 160 55 6 1010 810 165 60 1200 760 160 55 6 1210 770 165 60 1200 800 160 55 6 1210 810 165 60 1200 900 160 55 6 1210 910 165 160 All Dimensions in mm Pentangle Shower Tray A C C 410 B 410 112 IR A 90 D Flat Top Upstand A B C D Legs A B 6 D 900 900 160 55 5 910 910 165 60 Quadrant Shower Tray A C e B Radius 550 112 AT Iso D Flat Top Upstand A B C D Legs A B C D 800 800 160 55 4 810 810 165 60 900 900 160 55 4 910 910 165 60 All Dimensions in mm 9 INSTALLATION Please read these instructions carefully before starting the installation procedure Important Notes 1 Itis recommended that the shower tray is installed before tiling This will make sure that the tray is rebated into the plaster behind where the tile face will be thus helping to achieve a watertight joint 2 With arebate or partial rebate the amount of adjustment on the enclosure could be affected Therefore make sure that the enclosure to be fitted has sufficient adjustment to mate with the shower tray 3 Awaste with an 85 mm diameter flange must be used with these shower trays as supplied The first step of the installation is to decide whether you n2. E mail leech dnet co uk Fax 028 9044 9234 Post Maryland Industrial Estate Ballygowan Road Moneyreagh Co Down BT23 6BL Republic of Ireland Modern Plant Ltd Dublin Telephone 01 459 1344 Mon to Fri 9 00 am 5 00 pm E mail sales 0 modernplant ie Fax Dublin 01 459 2329 Post Otter House Naas Road Clondalkin Dublin 22 Modern Plant Ltd Cork Telephone 021 496 8755 Mon to Fri 9 00 am 5 00 pm E mail cork 9 modernplant ie Fax 021 496 8607 Post Tramore Road Cork FM 14648 Kohler Mira Limited October 2006
3. required refer to section Installation Rebating the Shower Tray Remove the tray from its position 4 Make sure that the floor is clean dry firm and level Coat the ribbed underside of the tray with silicone sealant a tiling cement or a weak mix of sand and cement 5 1 Then press down into place ensuring the tray is positioned into rebates Note Where the tray comes into contact with the wall or plaster board surface apply a liberal amount of silicone sealant before installation This will help secure the tray in position and reduce any rubbing of the surfaces 11 Make sure that the tray is level Note The bottom of the shower tray has a built in fall to allow for correct drainage Therefore check the edges of the tray with a spirit level refer to Figure 2 Make sure that the shower tray is level Figure 2 Level the Shower Tray Connect the waste pipe Seal the joint between the shower tray and adjoining wall with silicone sealant to provide a secondary seal The area is now ready for tiling The 3 mm gap between the tiling and the shower tray must be filled with a bead of silicone sealant refer to section Installation Rebating the Shower Tray 12 Riser Installation 1 11 12 Carefully remove all of the blue protective film from the tray for inspection Attention should then be paid to effectively cover the tray to protect from damage Spots on the adjustable leg mouldings are pro
4. 2 PG pergamon 1570 003 WH white Connector 135 Degrees 1570 003 SC soft cream 1570 003 PG pergamon Sg 1570 004 WH white Quadrant Panel 1570 004 SC soft cream 1570 004 PG pergamon 1570 005 WH white 1200 mm Panel 1570 005 SC soft cream 1570 005 PG pergamon 1570 589 WH white End Piece 1570 589 SC soft cream 1570 589 PG pergamon TI for use with Square Rectangle and Pentangle Trays 1570 280 Mira Flight Riser Fittings Pack Comprising of 1 Leg Fd 1 Clip c3 1 Locator 2 Sticky Pads 1570 296 6 Leg Pack i E 23 J W CUSTOMER SERVICE Guarantee of Quality Mira Showers guarantee your product against any defect in materials or workmanship for the period shown in the Guarantee Registration Document included with your Shower Tray Alternatively to confirm the applicable guarantee period please contact Customer Services To validate the guarantee please return your completed registration card Within the guarantee period we will resolve defects free of charge by repairing or replacing parts or modules as we may choose To be free of charge service work must only be undertaken by Mira Showers or our approved agents in Northern Ireland and Republic of Ireland Service under this guarantee does not affect the expiry date The guarantee on any exchanged parts or product ends when the normal product guarantee period expires Not covered by this guarantee Damage or defects arising fro
5. Flight z ag ac LLI e IE p E LL RISER AND NON RISER Installation amp User Guide These instructions are to be left with the user CONTENTS Int fols LU fox i to m RT 3 cree 3 Important Safety Information eene 4 Pack Contents wanna inn nas ee Eua seers eve 5 Square or Rectangular Shower Tray esse 5 Pentangle Shower tay ribbon nasa 6 Quadrant Shower Tray oooooWoWo WWooWoW mna 7 DIMONSIONS 8 Square or Rectangular Shower Tray Woo 8 Pentangle Shower Tray teret iot eic La asa 9 Quadrant Shower Tray woo oo oo ntenm ettet nnn nnns 9 Installation ertt erret an aan aa ainun 10 NonsRiser Installatiori iier tin kana means 11 Riser Installation oor o maa mtr Pe e rte 13 Rebating the Shower Tray oooooo oooo momongan 14 Basic Panel Installation ss ess oom 15 square Rectamgie x ian ama tipi aera pant mua masam 15 PENtANngIO i eni tra 17 Q adraNt seisis aa a aia an anna kaan nin 19 Maintenan e e ia aa aa 21 General 21 e Tem aE 21 Ding 22 Spare PaftS o ie nana 23 Customer Service aman Back Page INTRODUCTION Thank you for purchasing a quality product To enjoy the full potential of your new shower tray please take time to read this guid
6. dance with the recommendations given in this manual 2 Periodic attention is given as necessary to maintain the product in good functional order Recommended guidelines are given in the Maintenance section Warning The Mira Flight 760 and 800 variants weigh less than 25 kg and are a one person lift All other Mira Flight tray variants weigh in excess of 25 kg and will require a two person lift PACK CONTENTS Tick the appropriate boxes to familiarise vourself with the part names and to confirm that the parts are included Square or Rectangular Shower Trav 9 L 1 x85 mm waste O 1 x Square or Rectangular Shower Tray Square Rectangular Riser Conversion Kit if purchased Quantity Quantity Description Square Rectangle or 900 x 760 rectangle all other rectangles Q tos SQ s ma me NN ZI MAKAN CNN ff l IT ES Panels M Pentangle Shower Tray Pentangle Riser Conversion Kit if purchased Si css Sis ois AR foe 8 s E I MAN e 7 T Quadrant Shower Tray U 1 x 85 mm Waste Square or Rectangular Shower Tray A C C 112 90 D Flat Top Upstand A B C D Legs A B C D 760 760 160 55 4 770 770 165 60 800 800 160 55 4 810 810 165 60 900 900 160 55 4 910 910 165 60 900 760 160 55 4 910 770 165 60 1000 760 160 55 6
7. ding the shower tray has been correctly installed in accordance with the instructions contained in this guide difficulties should not arise If any maintenance is required then it must be carried out by a competent tradesperson for whom the maintenance instructions are provided Cleaning It is advised that the shower tray is cleaned immediately after use to remove any insoluble products Hot soapy water should be used and then the tray should be wiped Cleaners of gritty or abrasive nature should never be used The acrylic ABS surface of this shower tray has good resistance properties to acids but should not come into contact with alkalis or organic solvents such as caustic soda dry cleaning agents and paint strippers 21 ACCESSORIES Offset Leg Adaptor Fittings Kit 2 off Patent Pending 1570 557 WH white The Offset Leg Adaptor allows the Adjustable Legs to be installed offset to the tray thus allowing installation of pipework behind the Adjustable Legs refer to illustration Important Unscrew and remove the Locking Nut when using the Offset Leg Adaptor Shower Tray Offset Leg adaptor Adjustable Leg with locking Nut removed Upstand Tiling Strip 3 off 1250 mm long 1570 558 WH white Eliminates the need to rebate the shower tray into solid or stud walls Apply Silicone Sealant SPARE PARTS 1570 002 WH white Connector 90 Degrees 1570 002 SC soft cream 1570 00
8. e thoroughly and keep it handy for future reference Important The shower trays featured in this manual are available for use as riser and non riser products Carefully unpack and check the tray for colour size general acceptability and compatibility with the shower enclosure and other bathroom furniture Check for transit damage and report any faults immediately to your supplier No claims for the above will be considered after installation Mira Flight Shower Trays are available in various shapes and sizes with or without upstands and are all supplied with an 85 mm top access waste and trap Mira Flight Riser Conversion Kit comprises of adjustable legs panels panel securing clips corners and optional end pieces Riser Conversion Kits are available to purchase separately Mira Flight Offset Leg Adaptor Fittings Kit for use with the Mira Flight Riser Conversion Kit the Offset Leg Adaptor allows the installation of pipework behind the adjustable legs Offset Leg Adaptor Fittings Kits are available to purchase separately refer to section Accessories Mira Flight Upstand Tiling Strip Upstand Tiling Strips are available to purchase separately refer to section Accessories Patents Patent Applications GB 0526168 Euro 1667562 IMPORTANT SAFETY INFORMATION Caution These products are precision engineered and should give continued superior performance provided 1 They are installed and maintained in accor
9. ece End Piece Corner va Figure 9 Corner Install the Panels 18 Quadrant 1 Cut the panel to length Note Cut each end equally to maintain the correct fit of the curved panel The panel can be cut or shaped to suit the wall profile e g skirting board 2 Remove the backing from one side of each of the pads and stick the pads to back of locators 3 Slide the locators onto the clips refer to Figure 10 Pad Locator SC Clip Figure 10 Assemble the Panel Fixings 4 Slide the clips onto the legs until the bottom edge of the pad is 55 mm from the floor Make sure that they are parallel to the floor refer to Figure 11 Locator and Clip with adhesive pad attached Make sure that the top edge of the clip is parallel to the tray 55 mm Figure 11 Install the Locators and Clips 19 Offer up the panel to the tray and make sure that the panel is the correct length Note If extra panel stability is required secure wooden blocks or batons to the floor along the rear edge of the panel as shown Remove the backing paper from the sticky pads and remove the protective film from the panel Put the panel in position and press firmly Continue along the panel making sure that it sticks correctly refer to Figure 12 Seal the top edge of the panel to the tray wall using a line of silicone sealant Wooden Block or Baton Panel Figure 12 Install the Panels 20 MAINTENANCE General Provi
10. eed a non riser or riser installation for your tray To find out answer these simple questions 1 If the floor is out of level by 1 4 6 mm or more across the tray length the installation of a riser tray is recommended 2 Can a hole be made to fit the waste into the floor timber between the joists CSCS YES NO Follow Non Riser Follow Riser Installation Installation Procedure Procedure and Purchase a Riser Conversion Kit 10 Non Riser Installation 1 Carefully remove all of the blue protective film from the tray for inspection Caution Additional protective coverings such as a dust sheet should then be used to protect the tray from damage from falling objects 2 Fitthe 85 mm top access waste supplied to the tray before setting down being careful not to overtighten Make sure that the seal is in place Additional beads of silicone sealant must be used refer to Figure 1 Note To tighten remove the Shower Grid from the Flange and turn it upside down Locate it into the slots on the flange and tighten in a clockwise direction Remove and refit the Shower Grid to it s original position Shower Grid invert to ON flange Ore Bead of Silicone Sealant E For Non Riser Installations coat the underside of the tray with silicone sealant a tiling cement or a weak mix of sand and cement 5 1 Figure 1 Install the Tray Waste 3 Position the tray up to the walls and rebate into the plaster as
11. m Thick Tile fa 5 mm Thick 16 5 mm Clear Area Silicone Sealant Grout Plasterboard 2 mm Thick 9 5 mm Thick Tile 16 5 mm 5 mm Thick i Clear Area SS 1111717171 Y Silicone Sealant 3 mm Gap Grout Plasterboard 2 mm Thick 9 5 mm Thick Tile 16 5 mm 5 mm Thick 7 u 3mm Gap A f f as f A f f VA VLLMLILILLLLLLLLLLLL LLL THIS SIDE SHOWN WITH STUD PARTITION Figure 3 Rebating the Shower Tray 14 BASIC PANEL INSTALLATION Square Rectangle 1 Cut the panel to length Notel When cutting to length make sure that vou take into account the amount of panel that goes into the corner connector and the end piece if required Notel The end piece is designed to be used against a flat wall surface and cannot be cut The panel however can be cut or shaped to suit the wall profile e g skirting board Remove the backing from one side of each of the pads and stick the pads to back of locators Slide the locators onto the clips refer to Figure 4 Pad Locator N Clip Figure 4 Assemble the Panel Fixings Slide the clips onto the legs until the bottom edge of the pad is 55 mm from the floor Where two clips are fitted on one leg one of the clips can be inverted to allow both pads to be located at the same height Locator and Clip with adhesive pad attached i Make sure that the Figure 5 top edge of the clip is Install the Locators and Clips
12. m incorrect installation improper use or lack of maintenance including build up of limescale Damage or defects if the product is taken apart repaired or modified by any person not authorised by Mira Showers or our approved agents This guarantee is in addition to your statutory and other legal rights Before using your Shower Tray Please take the time to read and understand the operating and safety instructions detailed in this manual What to do if something goes wrong If when you first use your shower tray it doesn t function correctly first contact your installer to check that installation and commissioning are satisfactory and in accordance with the instructions in this manual We are on hand to offer you or your installer any advice you may need Should this not resolve the difficulty simply contact our Customer Services who will give every assistance and if necessary arrange for our service engineer to visit If later the performance of your shower tray declines consult this manual to see whether simple home maintenance is required Please call our Customer Services to talk the difficulty through request service under guarantee if applicable or take advantage of our comprehensive After Sales service As part of our quality and training programme calls may be recorded or monitored Our Customer Services Team is comprehensively trained to provide every assistance you may need help and advice spare parts or a service
13. or RC Clip Figure 7 Assemble the Panel Fixings Slide the clips onto the legs until the bottom edge of the pad is 55 mm from the floor Note Make sure that they are parallel to the tray edge refer to Figure 8 Locator and Clip with adhesive pad attached Make sure that the top edge of the clip Figure 8 is parallel to the Install the Locators and Clips tay 17 5 Offer up the panel to the tray with the horizontal grooves nearest the floor and make sure that the panel is the correct length Note If extra panel stability is required secure wooden blocks or batons to the floor along the rear edge of the panel as shown 6 Remove the backing paper from the sticky pads and remove the protective film from the panel 7 f required fit the end piece onto one of the smaller panels 410 mm 8 Starting at the wall end Offer the panel up to the locator and press firmly refer to Figure 9 9 Fit the corner onto one end of the larger panel 710 mm so that it fits onto the fitted panel 10 Locate onto the fitted panel 410 mm and firmly press onto the pads 11 If required fit the end piece onto the other smaller panel 410 mm 12 Fit the second corner onto one end of the panel 410 mm so that it fits onto the fitted panel 710 mm 13 Press the panel firmly onto the locators 14 Seal the top edge of the panel to the tray wall using a line of silicone sealant Wooden Block or Baton End Pi
14. parallel to the tray 15 10 11 Offer up the panel to the tray with the horizontal grooves nearest the floor and make sure that the panel is the correct length Note If extra panel stability is required secure wooden blocks or batons to the floor along the rear edge of the panel as shown Remove the backing paper from the sticky pads and remove the protective film from the panel If required fit the end piece onto the panel Starting at the wall end Offer the panel up to the locator and press firmly Continue along the panel making sure that it sticks correctly refer to Figure 6 Fit the end piece and the corner to the other panel Fit the corner onto the fixed panel and continue along pressing firmly Seal the top edge of the panel to the tray wall using a line of silicone sealant Wooden Block or Baton End Piece End Piece Figure 6 Install the Panels 16 Pentangle 1 A Cut the panel to length Notel When cutting to length make sure that vou take into account the amount of panel that goes into the corner connector and the end piece if required Notel The end piece is designed to be used against a flat wall surface and cannot be cut The panel however can be cut or shaped to suit the wall profile e g skirting board Remove the backing from one side of each of the pads and stick the pads to back of locators Slide the locators onto the clips refer to Figure 7 Pad Locat
15. s of silicone sealant must be used refer to Figure 1 Connect the waste pipe Seal the joint between the shower tray and adjoining wall with silicone sealant to provide a secondary seal The area is now ready for tiling The 3 mm gap between the tiling and the shower tray must be filled with a bead of silicone sealant refer to section Installation Rebating the Shower Tray 13 Rebating the Shower Tray The figures below provide an indication of the type of typical recommended installation methods It does not provide a fully detailed description for ALL installation methods procedures To aid installation optional accessories are available refer to section Accessories Plasterboard Grout 9 5 mm Thick 2mm Thick 16 5 mm Tile 5 mm Thick Clear Area Silicone Sealant Grout 2 mm Thick Tile 16 5 mm 5 mm Thick Plasterboard 9 5 mm Thick AN UN 4 Clear Area N ie A Silicone Sealant 11 XI U g c 3mm A Gap Grout Plasterboard 2 mm Thick 9 5 mm Thick Tile 16 5 mm 5 mm Thick Clear Area Silicone Sealant 3 mm Gap THIS SIDE SHOWN WITH SOLID WALL Note The amount of rebate affects the enclosure size Plasterboard 9 5 mm Thick Grout 2 m
16. vided to help set equal heights Set the adjustable legs to the third spot from the bottom this will give the initial clearance for the waste supplied Note Do not adjust the legs above the fourth spot as this will be too high to accommodate the riser panel Fit the adjustable legs into the holes on the back of the tray Note A soft faced mallet can be used to aid installation Temporarily fit the waste outlet pipework and the trap to the tray Adjust the height of the feet to give the required clearance Note The feet must be adjusted so that the shower tray does not rock Position the tray up to the walls and rebate the tray into the plaster as required refer to section Installation Rebating the Shower Tray Note Where the tray comes into contact with the wall or plaster board surface apply a liberal amount of silicone sealant before installation This will help secure the tray in position and reduce any rubbing of the surfaces Make sure that the tray is level Note The bottom of the shower tray has a built in fall to allow for correct drainage therefore check the edges of the tray with a spirit level refer to Figure 2 If necessary adjust the height of the feet so that the tray is level in all directions Once the tray is level tighten the individual lock nuts on the leg sets and check the tray is firm and secure Tighten the waste being careful not to overtighten Make sure that the seal is in place additional bead
17. visit Mira Showers Kohler Mira Ltd Cromwell Road Cheltenham GL52 5EP 1056862 W2 B Mira is a registered trade mark of Kohler Mira Limited The company reserves the right to alter product specifications without notice www mirashowers com Spare Parts We maintain an extensive stock of spares and aim to have functional parts available for ten years from the date of final manufacture of the product Spares can be purchased from approved stockists or merchants locations on request or direct from Customer Services Spares direct will normally be despatched within two working days Payment can be made by Visa or MasterCard at the time of ordering Should payment by cheque be preferred a pro forma invoice will be sent Service Our Service Force is available to provide a quality service at a reasonable cost You will have the assurance of a Mira trained engineer agent genuine Mira spares anda 12 month guarantee on the repair Payment should be made directly to the Service Engineer Agent using Visa MasterCard or a cheque supported by a banker s card To Contact us England Scotland amp Wales Mira Showers Customer Services Telephone 0870 241 0888 Mon to Fri 8 00 am 5 30 pm Sat 8 30 am 3 30 pm E mail technical mirashowers com Fax 01242 282595 By Post Cromwell Road Cheltenham Gloucestershire GL52 5EP Northern Ireland Wm H Leech amp Son Ltd Telephone 028 9044 9257 Mon to Fri 9 00 am 5 00 pm
Download Pdf Manuals
Related Search