Home
        SGA01 Strain Gauge Amplifier User Guide
         Contents
1.       85  C       30 04 2008    Page 5 of 6    SGAO1 Strain Gauge Amplifier    Contact Information    Racelogic Ltd   Unit 10 Swan Business Centre  Osier Way   Buckingham   MK18 1TB   UK    Tel   44  0  1280 823803  Fax   44  0  1280 823595  Email  support racelogic co uk    Web  www racelogic co uk    RACELOGIC    be        25 MER                               Revision Date Description Author  1 24 07 2007 First Draft JH  2 11 01 2008 First Issue JH  3 30 04 08 Updated contact details MG  30 04 2008    Page 6 of 6       
2. SGAO1 Strain Gauge Amplifier       RACELOGIC  eM LES  SGAO01 Strain Gauge Amplifier  User Guide                      Page 1 of 6    SGAO01 Strain Gauge Amplifier    RACELOGIC        oh  LER   Contents  CONTENTS e                                                                                            2  TN TFRODUCT ION Ps E 3  CONNECTION e                                                                                                           3  PULL BRIDGE Oniebj or                                                                            EENE 3  HALF BRIDGE CIRCUIT PM                                                                                       M 4  QUARTER BRIDGE E OBIcCOL UU UE 4  CALIBRATION P                                                                                                           5  SPECIFICATION ee                                                                                           5  CONTACT INFORMA TION Pro 6  30 04 2008    Page 2 of 6    SGAO1 Strain Gauge Amplifier  RACELOGIC    Introduction    Racelogic s SGAO1 is a twin channel  user adjustable strain gauge amplifier  Each channel is designed for full bridge operation  but can be used with half   bridge and quarter bridge load cells if necessary  as discussed in the    Connection    section of this manual     Each channel is DC isolated  with an output range of  9V and a signal gain adjustable between approximately 25 and 1000     Connection to the SGA01 is made via screw termina
3. ls  with mini cable glands to allow wires to be run out of the unit when the lid is in place  preventing  interference with the screw terminals and the scale and setting adjusters     Connection    Wires can be run into the Strain Gauge Amplifier using the three mini cables glands  This allows the lid to be replaced  enabling secure connections to the  internal screw terminals without leaving them or the scale and offset adjustment screws exposed     This section details connection methods for use with full bridge  half bridge and quarter bridge circuits     Full Bridge Circuit                RACELOGIC Channel B Input  DI kel ue E    Amplifier Offset Gain  RLVB SGA 01      Channel A Input  Signal Ground     Signal Output C  output B Signal 1  SS  output A ona Offsct Gain       Output A Signal  y f       When using the SGA in conjunction with a full bridge load cell  no additional equipment is required  Simply connect the load cell to the SGA as shown in the  diagram above     30 04 2008    Page 3 of 6    SGAO1 Strain Gauge Amplifier   C RACELOGIC    Half Bridge Circuit    Addtional resistors fitted  to complete bridge       When using the SGA with a half bridge load cell  two additional resistors must be placed in the circuit  The resistors should be rated to the same value as the  maximum resistance of the load cell s internal resistors and must be placed as shown in the diagram above     Quarter Bridge Circuit    Addkional resistors fitted  to complete bridge          Quark
4. r Bridge      Channel B input Losd Coll      Power In             Oft Gain    e  8       Channel A Input       Output B Gnd N  ERN      output B Signal            Q Output A Gnd Offest Gain        Output A Signal L8 s    When using the SGA in conjunction with a quarter bridge load cell  three additional resistors must be placed in the circuit  These resistors should be rated to  the same value as the maximum resistance of the load cell s internal resistors and must be placed according to the diagram above     30 04 2008    Page 4 of 6    SGAO1 Strain Gauge Amplifier  RACELOGIC    pu  ms ES    Calibration    Calibration of the Strain Gauge Amplifier takes place in two steps  or two steps per channel if more than one channel is being used  offset calibration and  scale calibration     First calibrate the offset by subjecting the load cell to the conditions that relate to a zero value  typically no load   With the required load applied  adjust the     Offset    screw for that channel until the output voltage reads OV     Next  calibrate the scale by subjecting the load cell to a known non zero value  With the required load applied  adjust the  Scale  screw for that channel until  the output voltage gives the voltage desired for the applied load     Repeat for the second channel if necessary     Specification  Supply Voltage 6V     18V DC  CMRR 90cB typical  77dB minimum   Bridge Supply Voltage 5V  2mV  Output Range  9V  Gain 25     1000  adjustable   Operating Temperature  40  C
    
Download Pdf Manuals
 
 
    
Related Search
    
Related Contents
Cockpit SX 日本語取扱説明書  Bio Vac IV    ManualV1.0    Copyright © All rights reserved. 
   Failed to retrieve file