GIPDC/B User Guide - Aura Light Sverige
Contents
1. a gt green i Single gang PIR switch Replaces a standard light switch or dimmer Turns off automatically Turns on automatically Security mode Switches all lighting heating and ventilation loads up to 10A T gt green i t X Compatible with all BS4662 dimensions back boxes Remove top and bottom lugs if fitted Do not overtighten Location It is important to locate the detector so that any occupants fall within the detection zone shown on the diagram Do not block the sensor with a door or other object Do not install above a radiator or other heat source Avoid direct sunlight entering the sensor This product should be installed in accordance with the current IEE wiring regulations If in doubt consult a qualified electrician Use the extender if there is less than 25mm free space REMEMBER put the wires through the extender before connecting lt lt 25mm Ny xXx Y Sy us Detection zone green i May have red or brown sleeve 2 way switching 1 way switching If the lights are controlled from one location only wire as in the diagram Neutral mums Black or Blue Live Red or Brown Earth EZZZZZ Yellow Green Strapper eee Yellow or Grey If more than one detector is required to switch the lighting e g at the top and bottom of a staircase they can be wired in parallel as in the diagram ee green i Remove front cover Use a flathead scr2. ewdriver or similar to gently prise off the cover and replace with new one by snapping on to switch time setting on off battery Short press lights on Press for more than 5 seconds to activate see Activate section Short press lights off The lights will turn off whilst the area is occupied The unit will reset to automatic operation after a period of time Press for more than 5 seconds to de activate see Activate section daylight setting battery indicator PIR lens toggle switches o gt green i Time setting 1min 30min The lights will turn off after the set time period When movement is detected the time period automatically restarts Clockwise longer time period Daylight setting Use this setting to adjust the point at which daylight brightness automatically turns lights on Clockwise turn on with brighter daylight Auto on mode in this mode lights remain off if there is enough natural daylight Toggle switch settings C Sle Manual on use on button i Auto off when nobody in the ON OFF room after time period enters room on oF Auto off when nobody in the room after time period a Auto on when somebody cin Security mode activated See Security Mode section ON OFF pg 6 Security mode deactivated Corridor The above settings turn light s on when someone enters the corridor turn light s off when no
3. gt o mM 7 Replace front cover 2 Remove switch 5 Push into holder 8 Activate battery replacement 1 Remove front 4 Replace battery green i Lights turn off even though room is occupied e Check location of sensor see detection diagram e Increase timing typically 15 minutes for a living area Lights never turn off e The lights will only turn off after no movement is detected for the time period Is the time period set too long AS green i Voltage 230VAC 10 Frequency 50Hz Temperature 0 C to 35 C Power 10A Compliance BS EN60669 2 1 amp BS EN55015 EU registered design no 000638069 0003 000638069 0004 EMS 534520 FM 45789 Prrectioncs CP Electronics Brent Crescent London NW10 7XR T 44 0 333 900 0671 F 44 0 333 900 0674 www cpelectronics co uk enquiry cpelectronics co uk WD411 issue 1
4. movement is sensed for 20 minutes Only turn light s on if there is little or no daylight Bedroom The above settings turn light s on when the top button is pressed and turn light s off when no movement is sensed for 10 minutes green i Peaeuene e Before using the unit needs to be activated e Press and hold the top button for more than 5 seconds The red LED will flash to indicate that it has activated and the unit will now operate e If the unit is going to be out of use for prolonged periods more than 6 months it should be deactivated by repeating the procedure above with the bottom button This will help to prolong battery life green i security mode e Security mode can be turned on and off using the switches as shown in the setup section e When activated security mode is used to switch on lighting when it gets dark giving the impression a house is occupied e When the unit senses that it is dark outside the lights will automatically switch on for a period of 2 hours then switch off e The internal battery should last in excess of 3 years dependent on usage e When it needs replacing a red LED will flash on the front of the unit e Follow the steps opposite to replace the battery e Use only good quality 9V alkaline batteries type PP3 e Once the battery has been changed activate the unit as described in the activate section 6 Replace switch cover gt oO w Oo a J oO oO
Download Pdf Manuals
Related Search