L• WARNING Installation and Operating Instructions
Contents
1. do not naturally messages the meters has degrade or change with time under specified environmental conditions If a degradation in the got a malfunction and must performance is observed the device has probably been partly damaged and should be sent for be replaced repair or exchanged If the meter is dirty and needs to be cleaned use lightly moistened tissue with a water based mild detergent Make sure no liquid goes into the meter as this could dam age the meter Technical data Data in compliance with EN 50470 1 EN 50470 3 EN 62053 23 AD1 80MBIC direct connection 80 A inbuilt commun Modbus General characteristics e Housing DIN 43880 DIN 3 modules e Mounting EN 60715 35 mm DIN rail e Depth mm 70 Operating features e Connectivity to single phase network n wires 2 e Storage of energy values and configuration digital display EEPROM yes e Display tariffs identifier for active and reactive energy n 2 T1 and T2 Supply e Certified voltage range Un VAC 230 20 e Operating voltage range VAC 110 276 e Certified frequency fn Hz 50 2 e Operating frequency range Hz 48 62 e Rated power dissipation max Pv VA W lt 8 0 6 Overload capability e Voltage Un continuous VAC 276 momentary 1 s VAC 300 e Current Imax continuous A 125 momentary 10 ms A 3750 Display e Display type LCD n digits 8 2 decimal digit dimensions mm x mm 6 00 x 3 e Active energy 1 display 7 digit tariffs 2 kWh 0 01 display2. import or export arrow overflow kWh 999999 99 e Reactive energy 1 display 7 digit tariffs 2 kvarh 0 01 display import or export arrow overflow kvarh 999999 99 e Instantaneous active power 1 display 3 digit W kW or MW 000 999 e Instantaneous reactive power 1 display 3 digit var kvar or Mvar 000 999 e Instantaneous tariff measurement 1 1 display 1 digit T1 or T2 e Display period refresh S 1 Measuring accuracy at 23 1 C referred to nominal values e Active energy and power acc to EN 50470 3 class B e Reactive energy and power acc to EN 62053 23 class 2 Measuring input e Type of connection phase N direct e Operating range voltage phase N VAC 110 276 e Current ref A 5 e Current min A 0 25 e Operating range current Ist Imax direct connection A 0 020 80 e Operating frequency HZ 48 62 e Certified frequency Hz 50 2 e Starting current for energy measurement Ist mA 20 Optical interfaces e Front side accuracy control LED imp kWh 1000 Safety acc to EN 50470 1 e Indoor meter yes e Degree of pollution 2 e Operational voltage VAC 300 e AC voltage test EN 50470 3 7 2 KV 4 e Impulse voltage test 1 2 50 us kV 6 e Protection class EN 50470 class Il e Housing material flame resistance UL 94 class VO e Safety sealing between upper and lower housing part yes Embedded communication e Modbus RTU RS 485 3 wires up to 38 400 bps Lateral IR interfaces e For communication
3. AUTOMETERS LILELLIL III EB EBE VS active and reactive energy meter with measurement of active and reactive instantaneous power and inbuilt communication Modbus RTU 2 tariff Code Description AD1 80MBIC single phase digital active and reactive energy meter with active and reactice power indication direct connection 0 25 5 80 A 2 tariffs 2 SO and inbuilt communication Modbus RTU with MID certified A WARNING The Autometers range of DIN rail mounted meters should only been installed by a competent and qualified electrician who is fully aware of the latest electricity regulations concerning the installation of Electricity meters The AD1 80 must be installed in a suitable enclosure e This family of devices provides a set of single phase energy meters designed to be directly connected to system where high current is required All the meters are equipped with an easy to read LCD with green back light on which displays all the active and reactive energy counters with a red light LED which blink in proportion to the measured active energy and with a optocoupler that allows the storage of energy on two different tariffs Depending on the model a insulated Modbus communication interface is built in two solid state relay which generate pulses proportional to the measured energy Modbus communication interfaces offer a set of 15 measures Display 0898988 Eneray value kWh kvarh kWh kvarh display T8 e Running tarif called ta
4. e page on the display if no key is pushed for at least 20 sec the main page appears again Menu Communication Address In the Address page by kept pushed for 4 sec the Start key the value of the Address blink on the display Push Start key or charge the value Push the Menu key to confirm otherwise within 5 seconds the modification will be lost Main Menu Main Menu am kWh _ kvarh 2 e IEN M Q Start er 7 gt 4 sec Communication Baudrate In the Baudrate page by kept pushed for 4 sec the Start key the value of the Baud rate blink on the display Push Start key or charge the value Push the Menu key for 4 sec to confirm otherwise within 5 seconds the modification will be lost Main Menu Main Menu fai kWh__kvarh O Start o Menu gt 4 sec gt 4 sec Firmware information Diagnostic Page of the Display In any page of the Main Menu by kept push for 10 sec the Menu key the diagnostic page of the display appears If the Menu key is held down for other 4 sec the display shows information about the firmware release and the firmware checksum Diagnostic Message Service and Maintenance Error Condition It should not be necessary to recalibrate device during its lifetime as it is an electronic meter When the display show these with no moving parts with electronics and voltage and current sensors that
5. moduls connection LAN TCP IP M Bus KNX SD Card Datalogger yes Connection terminals e Type cage main current paths screw head Z POZIDRIV PZ2 e Type cage pulse output blade for slotted screw mm 0 8 x 3 5 e Terminal capacity main current paths solid wire min max mm 1 5 50 stranded wire with sleeve min max mm 1 5 50 e Terminal capacity pulse output solid wire min max mm 1 4 stranded wire with sleeve min max mm 125 Environmental conditions e Mechanical environment Mi e Electromagnetic environment E2 e Operating temperature C 25 55 e Limit temperature of transportation and storage C 25 70 e Relative humidity not condensation lt 80 e Vibrations 50 Hz sinusoidal vibration amplitude mm 0075 e Degree protection housing when mounted in front terminal IP51 IP20 x For the installation in a cabinet at least with IP51 protection
6. rif kWh kvarh T8 N D I CO LI CI CO nana L 0000 a e Energy export absorbed 0 non 0 ant ooo mk wvar E aero L T 1000 imp kWh O kWh _ kvarh e Displays inductive reactive power Displays capacitative reactive power e Full scale current e Consumption Bar display HHHH indication o percentage of Pmax e Precision control LED Commands kWh kvarh e Parameters set 0 u for reading Start Menu Symbols b e Measuring elements On e Reversal preventing device m e Protected by double insulation Installation and Operating Instructions Single phase Digital Energy meters Direct connection 80 A IIST109 01 Stand 15 06 2012 Sealable terminal covers MID calibrated AD1 80MBIC A Device code and certification data indications B Safety sealing between upper and lower housing part Cable stripping length and max terminal screw torque 80 A direct connection main terminals Screw driver PZ2 Tariff and communication terminals Screw driver blade 0 8x3 5 mm Wiring diagram 1200 Modbus RTU AD1 80MBIC 230 VAC 230 V only required if more than one tariff A fuse of 80 A is recommended for the line protection Terminal Description 1 Modbus network For the termination of the for the termination of the network short this terminal with terminal 3 2 Modbus network Data 3 Modbus network Data 4 Modbus netwo
7. rk Shield 6 7 Tariff signal isolated by a Opto Coupler When there is a voltage of 230 VAC connected the device store energies on the Tariff 2 registers otherwise on the Tariff 1 registers Lit Input for the phase conductor L1 y Output for the phase conductor N Measuring input of neutral Main Menu Device Switch ON Page 1 In this page the value of the currently growing Active Energy is represented or the last one that has grown The energy may be Consumed or Generated with Tariff T1 or T2 depending on the current Energy flowing Page 1 kWh _ kvarh Page 2 Page 2 By pushing any key the back light turns on Page 3 The next 8 Menu key presses allow the display of the 8 energy counters The counters are Active import energy on tariff 1 Active export energy on tariff 1 Reactive import energy on tariff 1 Reactive export energy on tariff 1 Active import energy on tariff 2 Active export energy on tariff 2 Reactive import energy on tariff 2 Reactive export energy on tariff 2 When is displayed an energy counter corresponding to the running tariff on the bottom row the power is displayed Page 3 Page 4 In this page the Modbus address or the primary address appears Page 4 This value can be altered see the section Communication Address Page 5 In this page the communication baud rate appears Page 5 This value can be altered see the section Communication Baudrate e Whichever th
Download Pdf Manuals
Related Search