Operating Instructions Tumble dryer
Contents
1. The washing does not dry or is too dry Error messages Technical information Technical data Standard tests Service Before contacting the service division Installation Positioning the tumble dryer Adjusting the feet Condensed water Electrical installation Door hanging Follow these instructions Quick guide Fabrics Turn on the main power switch Load the garments Select a programme and any options Press the Start button Drying programme finished Once drying has finished 16 16 16 16 16 16 17 17 17 18 18 19 19 20 20 21 22 23 24 24 24 24 24 24 24 24 Before using your machine for the first time Do not tumble dry Certain materials are not suitable for tumble drying Always check and follow the instructions on each item s laundry label You can find more information in the chapter Advice and tips before you tumble dry Note When starting the tumble dryer for the first time or after a long period without use you may notice a slight thumping noise This noise is completely normal and will disappear after a few loads See the Quick guide on the last page Safety instructions Read the operating instructions and keep them in a safe place e Electrical installation if required should be carried out by a qualified electrician e The machine should only be used for tumble drying as described in these instructions e Repairs and maintenance relating to safety or performance must be c2. 19 20 Installation 5 Fit the plastic cups so that the tags marked with arrows are against the front edge or side edge of the cover and press them firmly onto the cover Then break off the remaining tags 27 6 Push out the knock out hole on the back of the dryer you must not remove it just open it using a hammer and screwdriver 7 Push the tumble dryer in under the metal brackets Atthe same time keep the front edge raised by 10mm to 20mm a L 8 Lower the tumble dryer s front feet into the plastic cups and adjust the dryer to ensure that it is balanced Adjusting the feet Screw the feet in or out so that the tumble dryer is steady and balanced on the floor or on the washing machine Then tighten the lock nuts Condensed water The machine is supplied as shown in Option 1 inset This means that the condensed water is pumped into the condensed water container This must then be removed and emptied by hand Option 2 allows you to remove the small short hose from the nipple Attach the rubber hose supplied to the same nipple The water can then be pumped out into a sink or a floor drain 2a Max 1000 mm Installation Electrical installation Connect the machine by plugging it into an earthed wall socket The electrical wall socket must be placed outside of the installation area to be easily accessible Connection on delive
3. a sponge and a little dishwashing detergent if necessary Dry the filter carefully with a towel If you cannot remove the limescale you can buy a new filter from the retailer where you bought the tumble dryer Emptying the condensed water container The condensed water container must be drained after each load Remove the condensed water container empty out the water and replace the container If the condensed water container becomes too full the programme is interrupted and F10 is shown in the display Empty the container and press the Start button to restart the programme Cleaning the outside of the machine Clean the outside of the machine and the programme panel with a mild cleaner Do not use solvents as these can damage the machine Do not hose down or spray the machine with water Note Do not allow dust to accumulate around the machine Keep the area around the tumble dryer clean and cool dust heat and moisture prolong drying times Care and cleaning Cleaning the condenser 5 Replace the condenser When refitting the condenser check that it is replaced correctly The top of the condenser is marked upp up and oben The condenser should be cleaned at least three times a year If you have pets the condenser must be cleaned more frequently 1 Turn off the main power switch 2 Remove the lower plinth 6 Replace the plinth 3 Open the condenser panel by turning the two
4. knobs anticlockwise GE NI N V HE e z 4 Remove the condenser and rinse the lamella springs clean using a hand held shower for example Do not touch the lamella springs as you may damage the condenser Do not use pointed metal objects during cleaning Note Do not put the condenser in a dishwasher Troubleshooting The machine will not start Check e that the door is properly closed e that the main power switch is on e that the Delayed Start option has not been selected If so the time remaining until the start will be shown in full hours in the display e g 5 4 3h To cancel Delayed Start press the Start Stop button for 3 seconds e that the plug is connected e that the fuses circuit breakers in your house are intact Swap two circuit breakers over to make sure You cannot always tell from the outside if a circuit breaker is broken e thatthe overheating cut out has not been triggered see below Overheating cut out The overheating cut out shuts off the tumble dryer if the temperature is too high e g because dust is clogging the lint filter e Clean the lint filter e Check also that the condensed water container is not full and if necessary clean the condenser See the chapter Care and cleaning e The overheating cut out will reset automatically once the machine has cooled down Drying takes too long Empty the condensed water container an
5. 1 Phase 16 A EN 611 21 95 13 EEC Programme 3 Auto normal dry 7kg cotton temperature Normal Time saver The machine has been tested for 1 Phase 16 A For switching between 10 A and 16 A see the Electrical installation chapter Test method for noise measure IEC 60 704 2 6 ment 17 18 Service Before contacting the service division Before contacting the service division you should find out whether you can resolve the fault yourself See the Troubleshooting and Care and cleaning chapters If you still need to contact the service division make sure that you know the model designation type designation and serial number The model designation can be found in the stamped hole on the first page of the operating instructions and on the machine s panel The type designation and serial number can be found on the type plate lype designation A TYPETD60 1 C pa 230 V 1a c 2200 W M 2001450 w oa art no 9203162 012512345678 Serial number 12 digits 01 1 MPa Installation Positioning the tumble dryer The tumble dryer can be free standing or ina stack Remember that the tumble dryer produces heat and should therefore not be located in a room that is too small If the room is very small drying will take longer due to the limited quantity of air Caution A e Any electrical installation must be carried out by qualified professionals e The machine must not be insta
6. Operating Instructions Tumble dryer ISE CD601W Dear ISE customer Welcome to the family of ISE customers We hope that you will have many years of use from your new machine The machine has many special functions To ensure that you get the most out of these functions we recommend that you read the operating instructions before using the machine The operating instructions contain information on how to avoid damaging the environment Contents Before using your machine for the first time Do not tumble dry Safety instructions Installation Safety Interrupting a programme Transport Winter storage Packing material Recycling Child safety General Description of the tumble dryer Front panel Advice and tips before you tumble dry Have the clothes been spun Materials that can be tumble dried Materials that must not be tumble dried Static electricity Tumble drying Sort your fabrics Turn on the main power switch Open the door load the items and then close the door Select the programme Selecting Options Press the Start button Drying programme finished Once drying has finished Care and cleaning Cleaning the lint filter Emptying the condensed water container Cleaning the outside of the machine Cleaning the condenser ANDO AAP A HH HP WO W O O 10 10 10 10 10 12 13 13 13 14 14 14 14 15 Troubleshooting The machine will not start Overheating cut out Drying takes too long
7. Start in whole hours Press the button to select a delayed start of 1 to 24 hours The lamp next to the button lights when Delayed Start is selected Press the Start button the machine counts down 1 hour at a time and starts after the selected delay This option cannot be used with the Timed dry or Air fluff programmes Tumble drying Press the Start button Stopping or changing a programme Press and hold button the Stop button for three seconds Note The programme will not be affected if you change the programme selector after the programme has started Loading or removing washing You can stop the tumble dryer after starting a programme by opening the door Load more washing or take out the items you want close the door and press the Start button A new estimate of the remaining programme time will be displayed after a few minutes Drying programme finished The text End appears on the display when the programme is finished If the Anti crease option has been selected the drum will rotate for three seconds per minute for two hours after the programme is finished Condensed water The condensed water container must be drained after each load Remove the condensed water container empty out the water and replace the container If the condensed water container becomes full to overflowing the programme is interrupted Empty the container and press the Start button to continue the programme Note Do not remove the condensed w
8. Tumble drying 5 Selecting Options By selecting options you can tailor a drying programme to suit your requirements The machine remembers which options you choose for each programme and uses them with one exception Delayed Start the next time you select the same programme You can of course change this if you want fe Temperature You can choose Temperature Low with all programmes except Revitalise e Select Temperature Low by pressing the button next to the symbol e The lamp next to the button lights when Temperature Low is selected Time saver You can choose Time saver with all programmes except Revitalise The programme is shortened by about 12 minutes e Press the button next to the symbol e The lamp next to the button lights when Time saver is selected anti crease This option means that the drum will rotate for three seconds per minute for two hours after the drying programme has finished The option prevents the fabrics from remaining in the same position and becoming creased if you are unable to remove them immediately after tumble drying has finished Cannot be selected with the Air fluff programme e Select Anti crease by pressing the button next to the symbol e The lamp next to the button lights when Anti crease is selected Delayed Start First select which programme you want to use and then select Delayed Start by pressing the button next to the symbol The display shows Delayed
9. arried out by a qualified professional e Damaged mains cables must only be replaced by a qualified electrician e Sufficient ventilation is required to prevent smoke from open fires or fumes from equipment burning other fuels being sucked into the room when the tumble dryer is running e Do not dry dirty laundry in the tumble dryer e Items that are stained with e g cooking oil acetone alcohol petrol kerosene stain remover turpentine wax and wax remover should be washed in hot water with extra detergent before they go in the tumbler dryer e Items such as foam rubber latex plastic waterproof textiles rubber coated items and clothes and foam rubber filled cushions must not be dried in the tumbler dryer e Fabric softener or similar products should be used as per the recommendations of the detergent manufacturer e The machine is not designed to be used by persons even children that are physically or mentally handicapped or lack experience and knowledge Such persons must receive instruction in how to use the machine from the person responsible for their safety e Children must be watched to ensure they do not play with the machine e Do not let lint accumulate near the dryer e Do notinstall the dryer behind doors with lock sliding doors or next to the doors with hinges so that opening of the dryer door will never be hindered Caution A Never stop a tumble dryer before the programme is completed unless you im
10. ater container while the machine is running Tip As the condensed water is decalcified it can be used in steam irons Pour it through a coffee filter Automatic emptying If you want the water to empty automatically see the Installation chapter Important e Clean the lint filter after each load See the Care and cleaning chapter e Empty the condensed water container after each load Caution A If the lint filter becomes clogged the machine s automatic overheating cut out may be triggered In order to be able to restart the machine you must clean the filter and allow the machine to cool down for around 30 minutes Turn off the main power switch Remove the clothes and close the door to prevent small children from climbing into the machine Bina drying has finished 13 Care and cleaning Cleaning the lint filter The lint filter must be cleaned after each load If you have very hard water this can cause limescale deposits in the lint filter Check for any limescale deposits when cleaning the lint filter and if necessary wash the filter by hand 1 Grasp the filter handle and pull it towards you 2 Pull the filter out of its holder 3 Open the filter and remove the lint from all sides of it by hand Use a soft dry cloth to remove any deposits 4 Replace the filter in its holder Note If you have hard water the filter should be washed with water to get rid of any limescale deposits Use
11. d check that neither the lint filter nor the condenser are clogged See the chapter Care and cleaning e Overly long drying times may also be due to the tumble dryer being located in a confined area or room that is too small causing the air to become too hot e Make sure that the tumble dryer has access to more cold air open doors and or windows The washing does not dry or is too dry e The door has been opened while the programme is running which disrupts the moisture monitoring function Error messages If F10 flashes in the display the condensed water container is full Empty the container and restart the programme If F30 is flashing in the display the maximum permitted programme time has been reached Read Drying takes too long in the Troubleshooting chapter to find out what to do Technical information Technical data Height Width Depth Weight Cylinder volume Max drying capacity Speed Rated power Drum material Outer casing material Setup Drain Standard tests Europe Drying performance Energy declaration 850mm 595mm 585mm 47kg 1111 7kg 52 rpm See type plate Stainless steel Powder coated and hot galvanized sheet steel or stainless steel Stacking or freestanding 1 7m polypropylene hose 3 4 BSP connection 2 0m rubber hose EN 611 21 95 13 EEC Programme 3 Auto normal dry 7kg cotton temperature Normal Time saver The machine has been tested for
12. e button with the time symbol The time is shown on the display and you can choose a programme time between 30 minutes and 3 hours Tumble drying Programme chart Here we present a few examples of the energy and time consumption of a few different programme settings Consumption can vary according to room temperature humidity load variations in the power supply and selected options For the consumption values given below the requirements are as follows Temperature of intake air 23 C Moisture content of intake air 55 Drying temperature Normal or low Heater output 2500W Programme chart Program Material Temperature Max load Energy consumption Programme time kg approx kWh approx hrs and min 800 rpm 1600 rpm 800 rpm 1600 rpm Auto extra dry Cotton linen Normal 7 0 4 5 3 3 2 00 1 35 Auto dry Cotton linen Normal 7 0 4 2 3 3 1 50 1 30 Auto dry Crease resistant polyes Normal 3 5 1 9 0 55 ter cotton Auto normal dry Cotton linen Normal 7 0 3 9 2 8 1 40 1 15 Auto normal dry Crease resistant polyes Normal 3 5 1 7 F 0 45 ter cotton Auto normal dry Acrylic rayon acetate Low 3 5 2 0 1 15 Auto Iron dry Cotton linen Normal 7 0 3 0 2 2 1 35 1 10 This programme is EN 61121 compliant During testing the tumble dryer shall have a 16A connection and Time saver shall be activated Energy and time consumption in compliance with EN 61121 12
13. e is for items that are particularly difficult to dry e g jeans with very thick seams Note Knitted fabrics in particular are prone to shrinkage Use the Auto dry Auto normal dry or Auto Iron dry programmes for these items Stretch clothes back into shape immediately after drying Auto dry and Auto normal dry These programmes shut off the heat once the load is dry but before itis over dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Use these programmes when you want items to be completely dry Auto Iron dry This programme shuts off the heat once the load is just damp enough for ironing or pressing Time programme The programme length you choose depends on what you intend to do with the items after drying them Use trial and error to find out what works best When you use Timed dry to tumble dry a load of mixed fabrics some of the garments may remain damp Tumble dry any damp garments for a further 30 minutes or so using the Timed dry programme Note When using the Timed dry programme garments can become over dry if you have selected too long a drying time This can cause the items to shrink or crease and become rough Synthetic materials can also become charged with static electricity Revitalise Use the Air fluff programme when you just want to refresh air or soften up items Specify the programme time by pressing th
14. een taken to dispose of it Contact your local authority for information about where and how your machine can be recycled correctly Child safety General Do not allow children to play with the tumble dryer A The tumble dryer does not start automatically when the door is closed if a child pulls the door shut from the inside for example Description of the tumble dryer oe ee OOO i J gt 1 Main power switch 6 Outer door 2 Condensed water container 7 Fan behind hatch 3 Panel 8 Condenser 4 Type plate 9 Lint filter 5 Lint filter holder Front panel 2 LO s uo Ea 1 Main power switch 2 Programme selector 3 Options buttons 4 Display window 5 Start 6 Stop Advice and tips before you tumble dry Here are some tips that may help you before you begin tumble drying Have the clothes been spun Items to be tumble dried should be spun at 1000 rpm or faster Higher spin speeds save both energy and drying time Materials that can be tumble dried This symbol means that the material is suitable for tumble drying Fabrics best suited to tumble drying are cotton fabrics terry cloth and synthetic fibres Garments will be softer and lighter when tumbled than when hung out to dry Note The tumble dryer does not cause any significant wear to fabrics The lint that is trapped in the lint filter consists of dust and fibre residues whic
15. h form when the items are used Materials that must not be tumble dried Kl this symbol means that the material is not suitable for tumble drying Certain materials may melt or become a fire hazard if exposed to heat and others can lose their shape or shrink And do not tumble dry e materials labelled Do not dry near heat e garments that have been dry cleaned at home e plastic foam e fibreglass material e wool must not be tumble dried because of the risk of felting Static electricity To reduce the risk of static electricity in the laundry after tumble drying you can e Use fabric softener when washing e Wait five minutes after the drying program ends before opening the door and removing the laundry from the dryer Note If the door is opened during the programme the programme will be interrupted and will return to the start The clothes may be too damp or too dry as a result 10 Tumble drying Below are step by step instructions to help you achieve the best possible tumble drying results Sort your fabrics You will achieve the most uniform drying results if the items are made of the same type of material Do up zips and buttons fasten belts sort the items and adjust the load and temperature Turn on the main power switch Open the door load the items 3 and then close the door Ai the programme Guidelines as to what specific programmes can be used for Auto extra dry This programm
16. he other side of the machine Refit the hinge 5 Loosen and remove the catch lift up and pull out and the cover plate on the door and the machine Switch the catch and the cover plate 6 Move the plastic plugs on the upper and lower edges of the door Use a flat bladed screwdriver to remove the plugs 7 Refit the door by loosening the hinge screws slightly affixing the door and closing it Retighten the hinges Replace the plinth 23 24 Quick guide Fabrics e Dry fabrics of the same type together to ensure that they dry as evenly as possible Turn on the main power switch Select a programme and any options e Turn the programme selector to the required programme e Select any options and settings Load the garments e Close the door Art No 80 902 00 Rev 01 We reserve the right to make changes 5 Press the Start button e End appears on the display when the programme is finished If the Anti crease option has been selected the drum will rotate for three seconds per minute for two hours after the drying programme is finished e Clean the lint filter after each load e Empty the condensed water container re drying has finished 6 Drying programme finished e Turn off the mains power switch and close the door CE Printed on environmentally friendly paper that meets the requirements of Mllj6f rbundet and Naturskyddsf reningen
17. lled behind a lockable door a sliding door or a door with hinges on the opposite side to those of the tumble dryer e The tumble dryer s plinth ventilation must not be blocked by a rug or the like Tip To improve ventilation leave the door to the room where the tumble dryer is located open Freestanding The tumble dryer can be positioned beside the washing machine Stacking The tumble dryer can be placed on top of a ISE washing machine In this case you use the stacking attachments foot cups and anti tilt devices that come with the machine You will find two foot cups in a bag in the drum and two anti tilt devices are attached to the bottom left corner at the back of the machine Extending plates can be ordered from your local retailer How to assemble the stack 1 Undo the anti tilt device 2 Undo the two screws indicated on the back of the washing machine 3 Secure the anti tilt device using the screws as shown in the picture 4 Attach the plastic cups for fixing the tumble dryer s front feet to the washing machine s top cover This is essential as only when the tumble dryer s feet are resting in the plastic cups can you be sure that the dryer is correctly positioned on the washing machine Break off tag A on the cup fitted on the right hand side and tag B on the cup fitted on the left hand side Then remove the paper from the self adhesive surface under the plastic cups D N B
18. mediately remove all the laundry and spread it out so that the heat can disperse Installation See the Installation chapter Safety e The machine must not be used for drying items that have been dry cleaned at home or fabrics that may contain residues of flammable liquids e The tumble dryer is protected by an overheating cut out This shuts off the machine if the temperature gets too high e A float shuts off the machine in the event of a blockage in the condensed water hose or if there is a risk of the condensed water container overflowing Caution A When the tumble dryer is operating the back of the tumble dryer will get very hot Leave the machine to cool completely before touching the back Interrupting a programme You can stop a drying programme by e Open the door The drum will then then stop automatically e Press the main power switch e Press the Stop button for three seconds When you want to resume tumble drying simply close the door and press the Start button Transport Winter storage If you need to move your machine or store it over the winter in unheated premises make sure that you drain the condensed water container beforehand Safety instructions Packing material Please sort waste materials in accordance with local guidelines Recycling This machine is manufactured and labelled for recycling In order to prevent injuries the machine must be made unusable once the decision has b
19. ry The machine is supplied as 1 Phase 230V 50Hz heat output 2500W and has a 16A plug Any residual current devices must be type A Switch over It is possible to switch over from 16 A heat output 2500W to 10 A heat output 1950 W The switchover must be performed by a qualified electrician 1 Turn off the machine using the main power switch 2 Press and hold the Anti crease button and then press the main power switch 3 If the upper right LED next to the programme selector and the LED next to the Anti crease button light up the machine is connected for 10 A and 1950 W If both the upper and lower right LEDs next to the programme selector and the LED next to the Anti crease button light up the machine is connected for 16 A and 2500 W Press the Time saver button once to switch the heat output 4 Press the Stop button to save your selection Repeat steps 1 to 4 to restore the machine to its original heat output 21 22 Door hanging 1 Hinge pins top and bottom 4 Locking hook 2 Cover washer 5 Hinges left right side 3 Plastic plugs on the upper 6 Plinth and lower edges Door hanging You can choose whether the door is hung on the right or the left Follow these instructions 1 Remove the plinth 2 Remove the hinge two screws 3 Lift the door up and remove it Support the door at the same time 4 Remove both door pins top and bottom Fit them on t
Download Pdf Manuals
Related Search