Rako RCP07 Wall-plates – Installation, Programming
Contents
1. 2 to scroll through channels mode buttons have the following functions 1 Scroll up and ident 2 Scroll down and ident p 3 Ident only 4 Save changes Off Exit programming Step 3 As each circuit flahes in turn use the raise and lower buttons to adjust lighting to the desired levels See details for scrolling Button 1 scrolls up 3 4 5 through channels 2 XE 6 1 15 KA 1 He Scrolling All circuits flash 0 flashes each existing 8 Ti p to indicate channel O circuit in turn 15 9 If at any point it is not clear which Button 2 scrolls 14 10 is the current down through 13 circuit address channels15 1 12 11 Continue incrementing channels with button 1 to reach 0 or return using button 2 button 3 will flash that circuit without scrolling on Step 4 Step 5 Press Off button to exit controller from programming mode To re program another scene repeat process from Step 12. the bossed inserts are aligned vertically and locate the PCB retainer in the patress Then using the 25mm fixing screws fix the front plate to the retainer and patress and back box Flush fixing to a UK back box Fit the PCB retainer in the back box so that the clear flange is flush to the wall Then using the 12mm fixing screws or 25mm if needed secure the front plate to the PCB retainer and back box Note If a metal front plate is being used as per the Rako RPP accessories then the aerial must be positioned outside of the back box This is because the front plate and back box will form a screen for the radio signal which will give very poor radio transmitting conditions To position the aerial correctly a hole must be cut in the back box and a small diameter hole drilled into the wall Straighten the aerial and push the aerial into the hole The best radio transmission will be achieved when all of the aerial fully extended and outside of the back box If because of physical constraints it is not possible to drill the hole in a position close to where the aerial emerges from the PCB retainer then the rear cover can be removed and the aerial re positioned in a more convenient aerial cut out see fig 2 Surface fixing with no back box Take the universal backing plate and screw this to the wall screws not included using the fixing slots Rotate the patress so that the bossed inserts are aligned horizontally and then using th
3. Rako RCPO7 Wall plates Installation Programming and Operating Instructions General The Rako RCP series of wall plates are designed to cope with a number of different installation situations These are predominantly Flush fixing into a UK back box Surface mounting with a UK back box Surface mounting with no back box or onto a European DIN standard or French box Tab In order to fit successfully into all the above situations the wall plate is made from an assembly of parts all of which are supplied as standard and are listed below The parts can also be identified from the drawing Fig1 Note Depending on the application not all of the parts may be used Pull out Prise Point Batteries Addressing ww Switches 1 x Front plate 1 x PCB retainer complete with PCB and button pad 1 x Rear cover 1 x Patress 1 x Universal backing plate Universal backing 2 x 6mm M3 5 screws 2 x 25mm M3 5 screws 2 x 12mm M3 5 screws 2 x self tapping screws Aerial Cutouts Fig 2 Rear View of PCB Retainer and Rear Cover Important This Section should be read before the installation of a Rako Control Panel Checking for correct operation plate S SS Rako control panels are supplied with a pullout ia tab to preve
4. e 2 x self tapping screws fix the patress to the universal backing plate taking sure not to over tighten the screws Insert the PCB retainer into the patress and then using the 2 x 6mm fixing screws secure the front plate to the patress fixing the screws through the PCB retainer and into the bossed inserts Surface fixing to European back boxes For fixing to European DIN or French standard back boxes the Rako universal backing plate has been designed so that two of the fixing slots match European DIN standard back box fixings and two match standard French back box fixings To mount the assembly orientate and mount the universal backing plate as applicable screws not provided and then follow the instructions for Surface fixing with no back box Care and maintenance Battery replacement The Rako RCP series of wall plates are designed to be powered by batteries The designed battery life is better than 3 years based on 30 button presses daily but the batteries will eventually need replacing In normal use the Led on the front panel illuminates momentarily when a button is pressed to indicate that a radio transmission has been made When the batteries are approaching the end of their useful life the Led will continue to blink after a button has been pressed When this starts to happen the batteries should be replaced as soon as possible Always use two CR2016 To replace the batteries unscrew the front plate and remo
5. n a panel set at Room 0 will be the same as pressing the same button on all of the control panels within the house This function can only be disabled using the Rako Rasoft programming software Using the Rako Rasoft programming software every fourth room 4 8 12 etc can be set as a group master to control the subsequent 3 rooms i e a Room 4 panel could control Rooms 5 6 and 7 The functionality of this is similar to the overall house control described above whereby pressing a button on a group master would have the same effect as pressing the same button on the panels in the slave rooms This function can only be enabled using the Rasoft programming software Installation Before assembly ensure that the rear cover is firmly fixed and that the aerial is positioned in a way as to not foul other components Warning Rako wall plates are designed to operate at safety extra low voltages 6V When fixing the wall plates to existing back boxes there may be mains wiring present if this is the case then the wiring should be made safe properly insulated and any metal back boxes earthed Earthing of the back box is essential if a decorative metal front plate is being used Should there be any doubt in how to do this contact a qualified electrician Rako Controls Ltd accepts no responsibility for any damage or injury caused by incorrect installation of a Rako product Surface fixing to UK back box Orientate the patress so that
6. nit will function with this address it is strongly advised to select your own house address and logical room addresses Once set any receiver modules need to learn the address of the control panel panels that they need to respond to To address a receiver module see the module s instruction manual Setting the address switches Each Rako transmitter has two 8 way banks of switches for setting its address The two sets of switches allow the user to choose from 256 house addresses and 256 room addresses To set the address unclip the rear cover whereupon the banks of switches will be now become visible To set an address use a small terminal screwdriver or similar device and carefully move some of the switches into the ON position Addressing uses binary encoding and the value of the switches is shown below Note Any control panels set with the same address will act as two or multi way controls 128 Eo 128 Clie a 64 Can o4 Cas 5 32 im 3 32 eo Sib wee S ie cy 2 amp 8 Cay 2 amp 8 Cus 2 Zui Eo 24 Tic 2 im IS 2 CEN 1 2m 1 2 O Room address 32 4 36 House address 128 16 144 Fig 5 Addressing Switches Special Addresses House 0 All switches set to off is not a valid address Room 0 All switches set to off is an overall house master address As a default this will act as a master panel for any rooms in a house Pressing a button o
7. nt inadvertent operation and battery i 2 deterioration during transit To remove this o first remove the rear cover by inserting the tip of m de a small screwdriver or similar into the prise point Fig 2 and gently lift off the rear cover This should expose the battery compartment and CD lo J addressing switches Care should be taken not CD 0o E 2 to touch or otherwise damage any of the CD O 4 exposed electronic components cD J cD With the rear cover removed pull out the tab protecting the batteries see Fig 2 your Rako Patress control panel should now be operational To A A check this press one of the buttons on the front PCB Retainer of the PCB retainer and the indicating LED Front Plate should illuminate briefly for a single flash If the Fig 1 LED does not flash or it flashes repeatedly for a Front View of Components short burst low battery warning then you should contact Rako controls on the number given below Addressing Before installing a Rako wall panel the address switches on the rear need to be set to an appropriate House and Room address Setting an address is the way in which interference between other Rako systems either with other rooms within your house or neighbouring houses is avoided It should be remembered that with a booster unit a Rako transmitter may have a range of over 100m Your Rako control panel comes set with a default address of House 1 Room 4 and whilst the u
8. ve the PCB retainer taking care not to damage the aerial note that when flush mounted the aerial may be located in a hole outside the back box Remove the rear cover and carefully slide out the batteries Replace with new batteries ensuring that the positive terminal makes contact with the battery clip and the negative terminal with the pad on the circuit board To ensure reliable operation always ensure that battery contacts and battery surfaces are kept clean of any grease moisture or other contamination Warning Lithium batteries may explode if handled incorrectly Always dispose of used batteries in accordance with manufacturer s recommendations General Rako thanks you for having purchased a Rako product and hopes that you are pleased with your system Should for any reason you need to contact us please contact us via our website www rakocontrols com or by phoning our customer help line on 0870 043 3905 Chose the scene to be re programmed Put controller into programming mode by pressing and holding the selected scene button and both one at atime raise and lower buttons together When in programming Button Action Once levels are set correctly for the chosen scene Save any changes by pressing button 4 Circuits will all flash to confirm Programming a Scene TIP ress the Ste p eae uton first Ste p 2 LED starts to flash after 5 seconds panel is now in programming mode Use buttons 1 amp
Download Pdf Manuals
Related Search