Spa functions Troubleshooting
Contents
1. The Light indicator lights up when light is on Blower key Press Blower key to turn blower on Press Blower Key again to turn off A built in timer automatically turns blower off after 20 minutes unless blower has been manually deactivated rst The blower indicator lights up when Pump 2 blower is on Up Down keys Use Up or Down key to set desired water temperature The temperature setting will be displayed for 5 seconds to con rm your new selection Econo key Press Econo key to switch from Normal mode to Economy mode To save energy the Economy mode Set Point is 20 F 11 C below the Normal mode Set Point The display toggles between Eco message and the current water temperature Press Econo key again to go back to Normal mode The display shows noE message for 3 secs2. 001208ENG www geckoalliance com Key 1 Press Key 1 key to turn Pump 1 on at low speed Press a second time to turn pump to high speed with a dual speed pump A third time turns pump off A built in timer automatically turns pump off after 20 minu tes unless pump has been manually deactivated rst The Pump 1 indicator lights up when Pump 1 is on With dual speed pump indicator will ash when Pump 1 is on at low speed Key 2 2 Pump System Press Key 2 key to turn Pump 2 on at low speed Press a second time to turn pump to high speed with a dual speed pump A third time turns pump off A built in timer automatically turns pump off after 20 min utes unless pump has been manually deactivated rst The Pump 2 indicator lights up when Pump 2 is on The Quick Reference Card provides a quick overview of your spa s main functions and the operations accessible with your digital control pad Spa functions Water temperature regulation In a regulation cycle the system rst gener ates water ow through the heater housing and the plumbing in order to ensure accu rate water temperature readings as well as avoiding heater activation in dry conditions After verifying pump activation and taking a water temperature reading if required the system automatically turns the heater on to reach and maintain water temperature at Set Point The Heater indicator lights up when the heate
3. ersists call your dealer or service supplier Filter cycle frequency Press Filter key again The display will show Fx with x representing the number of lter cycles per day up to 4 Default twice a day Use Up or Down key to change setting When the desired setting is displayed press Filter key to con rm A lter cycle will start immediately The Filter indicator lights up when a lter cycle is on Setting lter cycle duration Press and hold Filter key until the display shows dxx with xx representing the duration in hours Default 2 hours Use Up or Down key to change setting 0 no ltration 24 continuous ltration Note it s not recommended to set this to 0 Programming the lter cycles To program the lter cycles you must enter these parameters duration and frequency During a lter cycle pumps amp blower run at high speed for one minute to purge the plumbing Pump 1 or CP then runs at low speed for the remaining of the cycle Setting the temperature display units Press Filter key once more The display will show either F or C Use Up or Down key to change units Press Filter key a last time to go back to normal mode F Fahrenheit C Celsius Light key Press Light key to turn light on Press a second time to turn light off A built in timer automatically turns light off after 2 hours unless it has been manually deactivated rst
4. r is on It ashes when there is a request for more heat but the heater has not yet started Cooldown While performing this task the heater is not allowed to turn on and its icon ashes Smart Winter Mode Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes The Filter indicator ashes when the Smart Winter Mode is on Troubleshooting Hr An internal hardware error has been detected in in xe Contact dealer or service supplier HL The system has shut the heater down because the temperature at the heater has reached 119 F 48 C Do not enter the water Remove the spa cover and allow the water to cool down then shut power off and power your spa up again to reset the system Prr A problem is detected with the temperature probe Call your dealer or service supplier AOH Temperature inside the spa skirt is too high causing the internal temperature in the in xe to increase above normal limits Open skirt and wait until error clears OH The water temperature in the spa has reached 108 F 42 C Do not enter the water Remove the spa cover and allow the water to cool down to a lower temperature Call your dealer or service supplier if problem persists FLO The system does not detect any water ow while the primary pump is running Check and open water valves Check for water level Clean lter If the problem p
Download Pdf Manuals
Related Search