INSTALLATION and OPERATING INSTRUCTIONS
Contents
1. Mes A JH H Connecting the control panel E B Ej Connect the control panel in the modular connection on the side of the control TI 9 circuit board image 3 ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 8 20 PELLET STOVE ARITERM MYSINGE H 1 5 Safety system The stove is equipped with five independent safety systems 1 The feeder releases the pellets from a chute which separates the burner from the fuel store 2 The pellet hopper is equipped with tight fitting filler hatches The hatches must be closed and locked during operation as soon as one of the hatches is opened the fuel feed is interrupted and warning text is shown on the display 3 Three thermostats are located as shown in section 1 2 Components fig 1 If the maximum permitted temperature is exceeded the feeder stops the stove switches itself off and the display shows Operational stoppage The alarm must be confirmed by pressing a button Do not forget to rectify the cause of the operational stoppage See section 3 6 1 4 A flame sensor that detects flames is located in the burner housing fig 1 5 The door is equipped with a safety switch The safety switches are tested by unlocking one of the filler hatches during operation or start up The pellet feeder should then be stopped Repeat with the other hatch2. 19 ARITERM B 1 Product description H 1 1 General The stove has been developed to work as a primary heat source The stove s high level of efficiency in combination with automatic operation means that the stove replaces up to 80 of the heating in a normal family house with electricity as heating source The stove is designed for firing with wood pellets and requires an electrical power supply In the event of a power failure the stove requires power from another power source optional extra The integrated convection fan distributes the hot air around the house for best effect the stove should be centrally located on the lower floor of the house The room temperature is easily set from the control panel During thermostatic operation the stove is ignited and extinguished automatically Pellets are filled through two hatches on the top of the stove The filler hatches and door are equipped with safety switches Three safety thermostats are mounted together with the switches in a safety coil to prevent overheating Connection to the chimney can be either upwards or to the reverse The stove must not be used as an incinerator and must only be fired using wood pellets acc to EN 14961 NOTE The stove s surfaces on and around the glass become extremely hot ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 5 20 PELLET STOVE ARITERM MYSINGE H 1 2 Components The top 1 li
3. 1 3 Technical data H 1 4 Control panel Heating output 0 approx 6 3 5 kw The control panel has a display and adjustment dial see fig 3 Pellet 38 litres approx 20 25 kg The display shows the operating mode and the current temperature Efficiency level AIZ approx 91 91 Explanatory text scrolls through the display every 5 seconds CORZO MEE 0 012 0 01496 at 1396 O The adjustment dial is used by pressing or turning Smoke temperature HI 160 110 C Turn to scroll through the menu or change the value when adjusting EQ coe cetero ee cene tege 4 8 2 8 g s j 25 Pushing once makes a selection the menu Recommended negative pressure in chimney 10 Pa Temperature range thermostat approx 10 30 C Example UII snc e aate 100 138 kg Connect the stove to the wall socket Pressing once causes the panel to ask Start Electrical conriection dede eed 230 V 50 Hz Pressing again means that you confirm the question and the stove starts Electrical output firing If you turn clockwise instead you come to Stop T UserMenu and Back Electrical output operation Stop T Press to adjust stop temperature PUG i e storie Usermenu Press to adjust time and temperature sett
4. H 1 6 Settings The settings are made in the control panel in a menu system Before entering the menu the panel is in display mode Enter the menu by pressing the dial If the menu is inactive for a long time the panel returns to display mode The menu system consists of a main menu and sub menus Usermenu and Settings In addition there are menus only intended for authorised installers Turn the dial to scroll through the menu To jump out of the menu hold the button in for 4 seconds The menu appears as follows Main menu Start Stop A Stop T Usermenu Back ARITERM Confirm by pressing once to start stop Press to select and adjust desired stop temperature Press for Usermenu Press for display Usermenu 4 Settings Press for Settings Service Menu for authorised service technicians View Press for Display menu See levels operating time programme version etc OnTimer Limited operating time TimeStrt Start at desired time TimeStop Stop at desired time NghtDrop Possibility of lowering temperature below specific time period during the day 1 DayDrop Possibility of lowering temperature below specific time period during the day 2 Assist H Set the lower temperature that is required when maintenance heating is activated Clockset Set date and time Back Press for main menu Settings SetCode 021 Service M
5. control area It is an offence to emit smoke from a chimney of a building from a furnace or from any fixed boiler if located in a designated smoke control area It is also an offence to acquire an unauthorised fuel for use within a smoke control area unless it is used in an exempt appliance exempted from the controls which generally apply in the smoke control area The Secretary of State for Environment Food and Rural Affairs has powers under the Act to authorise smokeless fuels or exempt appliances for use in smoke control areas in England In Scotland and Wales this power rests with Ministers in the devolved administrations for those countries Separate legislation the Clean Air Northern Ireland Order 1981 applies in Northern Ireland Therefore it is a requirement that fuels burnt or obtained for use in smoke control areas have been authorised in Regulations and that appliances used to burn solid fuel in those areas other than authorised fuels have been exempted by an Order made and signed by the Secretary of State or Minister in the devolved administrations Further information on the requirements of the Clean Air Act can be found here http smokecontrol defra gov uk Your local authority is responsible for implementing the Clean Air Act 1993 including designation and supervision of smoke control areas and you can contact them for details of Clean Air Act requirements The Ariterm Mysinge pellet stove has been recommended
6. hatch is pulled straight out and hooked onto the side member NOTE When vacuuming the hot air fan be careful not to damage the long and vulnerable fan blades The fan bearings can start to whistle after operating for some time in a dusty environment Rectify this with a drop of oil on both bearings H 3 6 Operating stoppage If the stove does not start check first where the fault is located using the fault tracing diagram below If you consider that you have the necessary expertise rectify the fault as suggested If not or if the fault cannot be located contact your dealer After an unsuccessful start attempt or operating stoppage the burner crucible must always be emptied ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 14 20 H 3 6 1 Fault tracing and remedy PELLET STOVE ARITERM MYSINGE ARITERM Fault Cause Action Fault Cause Action Black ash or soot on the glass Too much ash in the crucible or blocked vent Dirty combustion fan Clean the burner crucible Clean the combustion fan hard cake amount The fuel has a too low ash melting temperature Incorrectly adjusted fuel or air See Menu amount The ash becomes a Incorrectly adjusted fuel or air See Menu Contact the fuel supplier The stove does not start nothing displayed The cable is not connected No voltage at the socket Stove fuse blo
7. temperature falls below the set temperature by less than 1 C the program switches to low output If no flame is detected the exclama tion mark illuminates and the stove goes into Operational stoppage mode 0 secs The feeder stops Combustion fan runs at max To blow ash out of the burner crucible The hot air fan runs 6 min Combustion fan stops The hot air fan stops ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 10 20 PELLET STOVE ARITERM MYSINGE H 2 Installation H 2 1 Positioning The installation must meet all applicable European standards local and national requirements The stove should be located in a central position on the lower floor of the house to facilitate heat spread The Building regulations contain a number of regulations to prevent fires Generally speaking the regulations are applied if the following is being observed e The stove must be placed at least 100 mm from the wall e The underlay must be made of non flammable material and extend at least 300 mm to the front and 100 mm to the side of the stove If the hearth surface is made of steel it must be at least 0 7 mm thick e Flammable material must not be exposed to temperatures exceeding 80 C To facilitate servicing and cleaning leave space on each side of the stove The weight of the stove is so low that no extra demands are made on the joists etc Any ex
8. ARITERM MYSINGE H 3 4 Sweeping The chimney must be swept twice a year Remove the cleaning hatch under the top plate stone 4 x Allen screws The flue and its connection and the area underneath the cleaning hatch must be cleaned at least once between the chimney sweepss visits Sweeping of the stove is carried out once a week during the firing season using the integrated soot rakes They are located behind the front panel and must be pulled backwards and forwards a couple of times each starting from above Measurement hole Remove the soot rakes as follows 1 The silicon seal seals against the stove body 2 Slacken off the nut a couple of turns 3 Press the soot rake upwards or downwards 4 Pull the soot rakes in pairs straight out 5 The soot rakes are sealed in reverse order The chimney must be checked for blockages if unused for a prolonged period KSEE RSS SSS ARITERM Use the handle for the door to open the front of Ariterm Mysinge Slide the handle diagonally upwards and then to the side see above H 3 5 Hot air fan Vacuum cleaning of the fans with a brush nozzle should be carried out a couple of times annually after removing the side hatch Do not forget to pull the plug out before the side hatch is removed The side hatch is secured using two panel screws that are visible when the filling hatch has been opened After the screws have been removed the upper section of the side
9. Check that there are no foreign objects stuck in the feeder auger Check switches and wiring to the motor Replace motor See Menu ErrorLO The flame sensor has not detected a flame during low output Incorrectly adjusted fuel and or air amount FeedLO or Fan LO The hopper is empty Pellets have jammed in the feeder The feeder auger does not rotate See Menu Fill up the pellets Remove pellets from the chute Ensure that there are no foreign objects in the chute Check that there are no foreign objects stuck in the feeder auger Check switches and wiring to the motor Replace motor ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 16 20 2 3 WN 8 gt W N gt EE PELLET STOVE ARITERM MYSINGE H 4 Removal H 4 1 Burner Open the door and remove the ash box Remove the four screws holding the burner flange to the stove wall fig 10 Pull the burner straight out until the cables connecting the burner to the control circuit board are visible Pull the two connectors apart The burner can now be removed Reinstall in reverse order 4 2 Firing element Remove the burner as above Remove the four screws 1 holding the upper part of the ignition bracket The firing element is now free 3 Disconnect the firing element s cables from the triac control and the terminal block Slacke
10. ER RE EX RE Pardue 6 Technical data i235 tay a Ra ORGS 7 Control panel v4 Ane 7 8 cad acon ees Peds 9 Settings doh ande aE ho hela eked ae gah 9 Control duration dues R ed 10 Installation POSIMIONING oa oes s PE dv er dee d 11 Chimney Regen pieds DEN 11 MetitilatlOti s c ceed ak recht ee o dos 11 Aritermi ATOW noue i dede PIER 11 Electrical 12 Documentation i229 use pps 12 Operation and maintenance Fel ace pete len eed R LE RA ER ERN EHE REN 13 Ash removal sss ar ek e ed 13 Glass ssa eden daug adds peria d d lr added oe 13 0 14 HOt air Tali c oe ade E CALI qs 14 Operating stoppage 14 Fault tracing and remedy 15 16 Removal BURNET abe 17 FiringelemeNt c c 002 sees 17 Combustion fan tas eR aes 17 Flame 17 HOt afar a desde duse SS bA debe zs wen 18 Control circuit 18 EUSES H ataie LL Pe odes ate aE 18 Overheat protection and safety switches 18 Warranty Warranty Parts aces ade fat rep ect GERE Rd 18 Declarationofconformity
11. as suitable for use in smoke control areas when burning wood pellets ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 19 20 If these instructions are not followed at installation operation and maintenance Ariterm Sweden AB s applicable warranties are not binding Ariterm reserves the right to make changes to components and specifications without prior notice 24 ARITERM Ariterm Sweden AB Flottiljvagen 15 SE 392 41 Kalmar www ariterm se
12. enu for authorised service technicians gn dose Adjust and test the pellet amount at ignition Adjust the pellet amount at high output TstHdose Test the pellet amount at high output LoPowOn Activate low output FeedLO Adjust the pellet amount at low output TstLdose Test the pellet amount at low output TempDiff Adjust the number of degrees between start and stop AudioOff Sound off or on Language Select language ResOnLog Operational time measurement is reset here Res lgn The counter for number of firings is reset here Default All the values are reset to factory settings here Back Press for Usermenu Ny Firing element Indicated Activated Feeder motor Combustion fan Fault function Stove Activated Activated Indicated in operation ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 9 20 H 1 6 1 control process Otherwise the electronics manage all processes as follows PELLET STOVE ARITERM MYSINGE ARITERM The feeder starts 220 330 secs The feeder stops Starter dose The combustion fans starts puls ing and stops twice The motor symbol goes out The time depends on the set pellet amount at ignition Pellet level should be approx 5 mm above the firing element hole START LOW OUTPUT Time Events Comments Time Events Comments 0 secs Firing element on After S
13. es loose on top of the stove with two guide lugs or is locked with quick release locks The top is lifted to access the cleaning hatch 2 When there is a hatch it is opened by removing the four screws one can then sweep the flue 3 and the smoke tubes 4 The flue can easily be turned through 90 which makes it possible to connect it to the chimney vertically or horizontally The front 5 can be opened This is how one accesses the soot scrapers 6 These four per handle can be slid forwards and backwards and scrape off the soot between the smoke tubes The door 7 is opened with the handle supplied and can be swung up on its two adjustable hinges The burner housing 8 is located in the hearth and is accessible The burner 9 sits loose in the burner housing The firing element 10 is located in the burner housing behind the burner It is the firing element that gives off the heat required to ignite the pellets The flame sensor 11 is beside the ignition unit and indicates if there is flame in the burner or not The ash box 12 is inset in the bottom of the hearth under the burner housing It can be removed when the door has been opened The combustion fan 13 is placed on the rear of the burner housing and provides the burner with air for combustion The control circuit board 15 is placed inside the stove and contains a transformer for 12V voltage to the electronics and control and supervision The hot air fan 16 is located
14. firing element ErrSafe The flame sensor has not detected a flame when the safety coil has been broken One of the safety thermostats has deployed One of the hatch switches is not switched on Check the fuel volume and that the hot air fan functions Clean the convection tubes Reset by pressing on the panel Ensure that the hatch and door is properly closed A weak clicking noise must be heard when closed The hopper is empty Pellets have jammed in the feeder The feeder auger does not rotate Error code Cause Action Error code Cause Action Powfail Power failure Check the electrical connection ErrorHI Incorrectly adjusted fuel and or See Menu The flame sensor has air amount not detected a flame FeedHI or Fan HI Errign Poor contact to firing element Check wiring and connections during high output Fill up the pellets Remove pellets from the chute Ensure that there are no foreign objects in the chute Check that there are no foreign objects stuck in the feeder auger Check switches and wiring to the motor Replace motor ErrStart The flame sensor has not detected a flame during the start up phase The hopper is empty Pellets have jammed in the feeder The feeder auger does not rotate Incorrectly adjusted starting dose Ign dose Fill up the pellets Remove pellets from the chute Ensure that there are no foreign objects in the chute
15. he screws that hold the fan brackets to the stove body 2 x Reinstall in reverse order E 4 6 Control circuit board 1 Remove the plug from the wall socket 2 Remove one of the side hatches according to the Hot air fan section 3 Remove the edge connectors on the long sides of the control circuit board by pulling them straight out from the circuit board 4 Disconnect the cable for the control panel located in a connector on one edge of the control circuit board Press in the hook on the underside of the connector and pull the cable straight out to the side 5 Release the three panel screws on the rear of the stove and remove the control circuit board H 4 7 Fuses 1 There are two fuses on the stove s input connector Both are 3 15A slow 2 When replacing the fuses pull the connector cover straight out to access the fuses Fig 11 H 4 8 Overheat protection and safety switches This work must be carried out by an authorised engineer Fig 11 ARITERM For warranty issues Ariterm Sweden AB refers to our local Distributor ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 18 20 PELLET STOVE ARITERM MYSINGE Declaration of conformity F rs kran om verensst mmelse Konformit tserkl rung Vaatimuksenmukaisuusvakuutus Ariterm Sweden AB Flottiljv gen 15 S 39241 KALMAR declare under our sole responibility that the product f rs krar under eget a
16. ings Depending on fuel density Back Press to return to the starting point a 550 gt 560 gt The stove is started by pressing the control panel dial and confirming Start by pressing again Take care not to start the stove when there M m are flammable objects above or immediately adjacent To shut off press the control panel dial and confirm Stop by pressing once Other menu steps are shown in section 1 6 076 947 ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 7 20 MULL 4 8675 Fig 3 PELLET STOVE ARITERM MYSINGE H Installing the control panel H Removing the control panel 1 Install the wall mounting with 2 screws 1 Slide the panel straight up 2 Hook one corner of the panel onto the wall mounting 2 Lift the panel straight out from the wall 3 Press the other corner of the panel onto the wall mounting ry E n L L 5 Es 3 D iE 1
17. inside the stove and sucks air from the rear of the stove which is then heated up in the smoke tubes and expelled through the holes in the front The pellet hopper 17 has space for 38 litres of pellets and is filled through the filler hatches 18 There is a hatch on each side so that one can place the stove in a corner if one so wishes The pellet feeder 19 is below the pellet hopper and consists of a rotating cylinder with a spiral spring that slowly turns at the bottom of the hopper and prevents blockages The patented design means that pellets cannot stick in the feeder Safety thermostats 20 are located on the 1 fall pipe from the pellet feeder 85 C 2 the pellet feeder front wall 85 C and 3 the flue 204 C The stove must not be modified and only spare parts recommended by the manufacturer may be used when the door has been opened It is installed with four screws on the rear of the stove body ARITERM Cleaning hatch 2 Filling hatch 18 Top 1 Flue 3 Smoke tubes 4 Front 5 Safety thermostats 20 Soot scraper 6 Door 7 Pellet feeder 19 Hot air fan 16 Control card 15 Burner housing 8 Burner 9 Ash box 12 Flame sensor 11 Combustion fan 13 Firing element 10 Sound trap Fig 1 ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 6 20 PELLET STOVE ARITERM MYSINGE Apnea H
18. isting chimney 4 F 1 N 100 lt d d 300 Fig 7 ARITERM E 2 2 Chimney The regulations regarding chimneys can be found in the Building regulations Observe the following e The highest surface temperature of the flue including insulation and surrounding shaft may be 100 C when the stove is running at full output The surface temperature of adjacent building parts may not exceed 80 C Minimum diameter round duct or side rectangular duct should be 80 mm The smoke ducts must be made of non flammable material of sufficient durability and with sufficient resistance to temperature variations climate effects corrosive smoke gases and slag and use of sweeping tools etc e It must be possible to clean the flue If fallen ash cannot be removed via the stove s cleaning hatch another cleaning hatch must be arranged The cleaning hatch must not be located in a room other than the one in which the stove is located e Connection to the chimney must be via a steel flue pipe of at least 2 mm thickness or minimum 1 mm thickness if stainless steel The joint is sealed with hard packed glass fibre or elastic sealing compound that can tolerate at least 250 C e All parts of the chimney situated outdoors must be insulated e stove must NOT be connected to divided chimneys or flue gas ducts The smoke gases contain water vap
19. n off the screw 3 that secures the firing element Remove the firing sleeve from the element Pull out the cables from the lead ins Reinstall in reverse order 4 3 Combustion fan Remove the burner and the ignition console according to the Firing element section Remove the red and the blue cable from the terminal block on the side of the bracket Remove the screws 2 holding the fan to the bracket Reinstall in reverse order 4 4 Flame detector Remove the burner and the ignition console according to the Firing element section Remove the white cables from the terminal block in the side of the bracket Remove the flame sensor but first note how it sits at the side of the bracket Reinstall in reverse order Burner ARITERM Flame detector Combustion fan ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 17 20 PELLET STOVE ARITERM MYSINGE 4 5 Hot air fan 5 Warranty Work is best carried out with both side hatches removed but they can also be accessed from one side or the other 1 Remove the plug from the wall socket 2 Open the top and slacken off the two panel screws on the upper edge of the side hatch 3 Pull the upper section of the hatch straight out and then lift up the panel so that it is free 4 Disconnect the cables from the fan by pulling the plastic covered flat pin sleeves from the motor p Remove t
20. nsvar att produkten erkl ren in alleiniger Verantwortung da das Produkt vakuuttaa omalla vastuulla ett tuote Pellet stove Ariterm Mysinge Neptuni Ekerum to which this declaration relates is in conformity with requirements of the following directives som omfattas av denna f rs kran r i verensst mmelse med f ljande direktiv auf das sich diese Erkl rung bezieht konform ist mit den Anforderung der Richtlinien jota t m vakuutus koskee on yhteensopiva seuraaviin m r yksiin EMC Directive 89 336 EEC Low Voltage Directive 73 23 EEC including amendments by the CE marking Directive 93 68 EEC The conformity was checked in accordance with the following EN standards verensst mmelsen r kontrollerad i enlighet med f ljande EN standarder Die Konformit t wurde berpr ft anhand der EN Normen Yhdenmukaisuus on tarkastettu seuraavien EN standardien mukaan EN 55014 EN61000 4 2 3 4 5 6 Level 2 Emission and immunity by electromagnetic disturbances EN 60335 1 1994 Safety of household and similar appliances Part 1 General requirements EN 14785 2006 Residential space heating appliance fired by wood pellets Requirements and test methods Kalmar 2013 10 22 Staffany Lundeg rdH Managing Director ARITERM H The Clean Air Act 1993 and Smoke Control Areas Under the Clean Air Act local authorities may declare the whole or part of the district of theauthority to be a smoke
21. om the same factory This can only be established through trial and error but generally the ash layer in the bottom should be a maximum of a centimetre deep We recommend removing the ash daily during the firing season or each time pellets are filled Remove ash through the door using the handle supplied Lift out the burner from the burner housing and remove any ash from the ash box Certain pellets generate a hard cake of cin ders this may need to be broken up using a screwdriver or removed using one s hands Ash from the stove must be stored in a container made of non flammable material for example a metal bucket until it has cooled sufficiently that it can be held in one s hand It can then be thrown away bear in mind that wood ash contains nutrients that can be beneficial to gardens H 3 3 The glass After a period of operation the glass in the door becomes coated with ash dust and eventually becomes opaque It should therefore be wiped off from the inside using kitchen roll moistened with normal tap water we recommend that this is done each time the pellets store is filled No cleaning agent is usually necessary If the pane of glass becomes black and or difficult to clean see section 3 6 1 When cleaning the black painted metal components only water and in certain cases washing up liquid should be used ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 13 20 PELLET STOVE
22. our that can condense to water if the temperature is sufficiently low approx 55 C which can cause damage both to the chimney and stove The temperature 1 m below the chimney top must be at least 60 C In the event of a chimney fire pull out the plug and call the emergency services H 2 3 Ventilation There must be at least one air supply ventilator in the room where the stove is located If there are other exhaust fans increase the number of supply ventilators until the fans no longer affect the pressure ratio We also recommend that a chimney fan is installed H 2 4 Ariterm Arrow Information about installation with Ariterm Arrow instead of a traditional chimney is available in a separate manual See Arrow Wall fan Installation and Operation instructions ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 11 20 PELLET STOVE ARITERM MYSINGE Eme H 2 5 Electrical connection white black The back of the stove is equipped with a orange red L Light sensor 1 5 m long cable with plug which must be black black black red red red connected to a 230 V 50 Hz mains supply Sak The internal wiring diagram black black black is shown in fig 8 orange brown Ignition element blue Connector gnition elemei NOTE If the connection cable is damaged orange it must be replaced by one of the
23. p 77 ITE R M 6 INSTALLATION and OPERATING INSTRUCTIONS 4 PELLET STOVE MYSINGE For a sustainable future PELLET STOVE ARITERM MYSINGE H Important points to note In order for the stove to function properly the following rules must be followed The stove needs air in order to function never close the supply air vent to the house Note that there must be at least one air supply ventilator in the room where the stove is located The room temperature must exceed 5 C for the thermostat to work Your installer must adjust the stove in connection with commissioning and fill in the values in the warranty proof of installation at the end of these user instructions The store should be emptied periodically and the sawdust removed using a vacuum cleaner Also test the safety switch by unlocking one of the filler hatches or the door during operation or start up The pellet feeder should then be stopped We recommend removing the ash daily during the firing season or each time pellets are filled Remove ash through the door using the handle supplied Lift out the burner from the burner housing and remove any ash from the ash box unburned pellets must not be emptied into the ash box there is a risk of them starting to smoulder After a period of operation the glass in the door becomes coated with ash dust and eventually becomes opaque It should be wiped off from the inside using kitchen roll moistened with normal ta
24. p water we recommend that this is done each time the pellets store is filled Wait until the glass has cooled If the pane of glass becomes black and or difficult to clean see section 3 6 1 Vacuum under the top panel s soot hatch once between visits by the chimney sweep the sweep normally comes twice a year Sweep your stove once a week during the firing season Sweeping is easily done by releasing and pulling the soot rakes backwards and forwards a few times Slide them in and secure them again Vacuum the inside of the stove annually to keep the fans clean See section 3 5 If you have installed Ariterm Arrow ash must be removed from it at least once every firing season NOTE When you start your stove for the first time there may be a slight smell of paint this is because the paint on the stove body must cure fully before one can obtain odour free operation ARITERM ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 3 20 PELLET STOVE ARITERM MYSINGE ARITERM ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 4 20 1 1 1 2 1 3 1 4 1 5 1 6 2 1 2 2 2 3 2 4 2 5 2 6 3 1 3 2 3 3 3 4 3 5 3 6 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 1 6 3 6 PELLET STOVE ARITERM MYSINGE B Table of Contents Product description General ele adhe debs P eRe 5 Components
25. same type contact the dealer fed white Ignition unit Remote option Tacho sensor i orange option Black 1 brown 1 O 4 o black i 5 F eee gray black PWM Out option yellow green _ 230 VAC_ FUSES 2x 3 15 AT H 2 6 Documentation The stove must be installed inspected and commissioned by an authorised engineer At installation the following data must be collected and gathered under the section Warranty and Installation proof Safety switches black white glass fiber a Convector fan black e Manufacturing number Installation date e Vacuum in chimney cold e Vacuum in chimney hot Outdoor temperature e Smoke gas temp at max operation e Carbon dioxide content CO e Distance to combustible material Control panel blue Feeder motor Fig 8 ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 12 20 PELLET STOVE ARITERM MYSINGE H 3 Operation and maintenance The stove is designed for a long service life motors and other moving parts are of a very high quality All bearings are lifetime lubricated and the only preventative maintenance that is normally required is sweeping and cleaning H 3 1 Fuel The stove must be lit with
26. tart LoPower scrolls through the The time depends on the set The firing element symbol illuminates display pellet amount at low output The feeder runs according to 120 secs The motor symbol illuminates FeedLO Combustion fan Fan LO Every 10 seconds Set temperature and room temperature are compared The flame sensor is checked If the room temperature reaches the set stop temperature the pro gram switches to extinguishing and then to Standby If no flame is detected the exclama tion mark illuminates and the stove goes into Operational stoppage mode Maximum time for firing element Hot air fan on n The flame symbol is displayed as If the flame sensor indicates i S long as the flame sensor indicates flame the firing element is shut off the flame symbol illuminates and the firing element symbol goes out Approx 8 min The feeder on at low output Runs from 1 8 6 seconds every 10th second Approx 10 min Operating phase The thermostat regulates the output according to the set values EXTINGUISHING HIGH OUTPUT After START HiPower scrolls through the display The feeder runs according to FeedHi Combustion fan Fan HI The time depends on the set fuel amount at high output Every 10 seconds Set temperature and room temperature are compared The flame sensor is checked If the room
27. wn The cable between the control panel and the control circuit board is not correctly connected Connect to earthed 230V socket Check the fuse Replace the fuse see section 4 7 Check that the lead is connected at both ends Smoke odour Blocked smoke access Contaminated convection ducts Negative pressure in the house Clean the stove see 3 4 Clean the stove see 3 4 Ensure that the stove has the necessary ventilation Condensation leaks from the stove s flue connection Flue smoke too cold for the chimney Increase the output by adjusting the amount of fuel and air Deactivate low output Insulate the chimney Install condensation trap The stove is in Standby mode The room temperature exceeds the set stop temperature The room temperature must exceed 5 C for the thermostat to work Set the desired stop temperature Increase Stop T above 30 C to start in On mode When the room temperature has exceeded 5 C adjust the desired stop temperature In the event of an unsuccessful start attempt or operating stoppage the burner crucible must always be emptied ARITERM SP PX26868 B 1 ARITERM SWEDEN AB Installation Instructions 2013 10 10 15 20 PELLET STOVE ARITERM MYSINGE ARITERM Error codes The firing element is not drawing any power Defective firing element Replace
28. wood pellets 6 or 8 mm class 1 according to Swedish standard The pellets are supplied in plastic sacks that can be stacked on pallets or other suitable surfac es Avoid exposing the sacks to moisture or mechanical stresses vibrations or blows Careless handling of pellets can easily reduce them to sawdust which can cause feed and combustion problems Fill the hopper with pellets slowly and without too great a drop The store should be emptied periodically and the sawdust removed using a vacuum cleaner The hopper is filled by opening the hatches above the pellet magazine The different stove models have different types of hatches Where there is a knob the hatch is opened by turning the knob a 1 4 turn anti clockwise To fully fill the magazine one has to open the other hatch The hopper can be filled while the stove is running but because the feeder switches off when the hatches are opened you only have a few minutes before the hatch must be locked again If the hatch is open for longer the flame is likely to get so low that the stove will switch itself off after which it must be restarted again ARITERM H 3 2 Ash removal The amount of ash that build up in the burner varies depending partially on how the stove is fired number of starts and stops division between full and half speed and partially on the quality of the pellets The ash content varies between different pellets but can also differ between different batches fr
Download Pdf Manuals
Related Search