Intel Server Board SHG2 Troubleshooting Guide
Contents
1. power cord into the power supply e Have you plugged the server into a powered on power strip e Some ATX power supplies have a power switch on the back of the power supply next to the fan is it switched on e Is the power supply set correctly to 110V or 235V depending on your power output e Is the front panel power switch cable properly connected to the front panel header pins on the server board e Remove and reseat the memory modules Try using memory modules from a known working server system e Remove all add in cards and see if the server boots using just the on board components If successful add the cards back in one at a time with a reboot in between to see if you can pinpoint a suspect card e Remove the processor and reseat it Though it is unlikely that a server will not boot there are many reasons why it may not boot If you are unable to resolve this issue please fill out the customer support form at the end of this document and call your customer support representative Please note the answers to the following questions below e What memory is the server using Is it on the tested memory list Visit the Intel support site for an updated memory list http support intel com support motherboards server SHG2 e What chassis and power supply is the server using e If you are using a chassis with front panel lights are there any front panel lights on e ls the power supply fan spinning e Does the system beep Se2. reboot in between to try to pinpoint a suspect card Remove and reseat memory modules Try using memory from a known working system Remove and reseat processor If you are using a switch box to share a monitor between multiple servers ensure switching to the proper server If you are unable to get a video image please fill out the included customer support form and call your customer support representative Please note the answers to the following questions below What memory is the system using Is it on the tested memory list Visit the Intel support site for an updated memory list http support intel com support motherboards server SHG2 What chassis and power supply is the system using If the chassis has front panel lights are any front panel lights on Is the power supply fan spinning Does the system beep See Issue 2 Please note any sounds emanating from the server system If you are using a third party video adapter please have manufacturer and model number ready SHG2 Troubleshooting Guide 6 05 20 02 e If the server will still not boot please fill in the issue report form at the end of this document amp contact your Intel customer support representative 4 am installing adapters in my powered down system and my system boots up when install a PCI adapter Server management features require full time standby power This means that power is still on to parts of the system even if you have tur
3. tise Netasedvies E a de ets fasten E Aa e arana niee hbo need 1 What is Flip Chip Pin Grid Array FO PGA 0 ceeeseecesescsseseseeeeseecsseceseeceeeceaeeeeeeeeaeeeeateeeeesenees 2 What type of battery is used in Intel Server Board SHG2 0 0 eceececcsceseseeeeseeeseeeeseecseeeeseeeeeees 3 How do l disable the onboard LAN oe ceceesesseeesesessecesesceseecsesesesesesceseecsececaeseeateceeeecaeeesateeeeees MeMo QUESTIONS 5 5 ecscezcreci r Meet tense eds eee ed a e UR eee eet emer as 1 What memory configurations are supported on the Intel Server Board SHG2 5 2 What kind of problems might occur in an SDRAM based system that uses non compliant DIMME aTe a e ahha ek aie Ach ae a a aad eles e ini eek hee Ree aioe Mine At Jumpers and BIOS Setup Options e ce ceeeceseecesescseeseseseeseecsseceseseseeecseecsaeecsececsenecaeecsececaeneeaeeeeeeecaeeeeateeeees 1 Why can t find speed settings in my BIOS configuration MOde ccceseeceeeeeeseteeeeeeeeeeeees 2 How should the jumpers be set on Intel Server Board SHG2 eceececeeeeseseneeeeseeeeeseneeeeeees NPUT OUTPUtS 3 E enced eid reese eo eee ethene tite aad at Sees ee ee eee esi es 1 Does the Intel Server Board SHG2 support Ultra ATA 33 66 100 hard drives seeee 2 What IDE cable should use to support both Ultra ATA 100 and previous IDE transfer PIOLOCOIS 7 enter etl hes ets teeta E A yacht at EE EEA Coates as tot dike Mame Doak E 3 Can I mix Ultr
4. 02 Utilities Intel Server Management ISM version System Setup Utility SSU version FRU SDR versions PCI Adapters Is this adapter on PCI Slot Manufacturer Model number Driver version the tested hardware list Onboard Devices Device In Use Video q 10 100 NIC m 10 100 1000 NIC m Adaptec AIC 7899W SCSI channel 1 Adaptec AIC 7899W SCSI channel 2 SHG Troubleshooting Guide 13 05 20 02 Peripherals Manufacturer Model number Quantity Comments Hard Drives SCSI or ATA Tape Drives Internal or external CDROM Internal or USB CDRW Internal or USB DVDROM Internal or USB Keyboard USB or PS 2 Mouse USB or PS 2 Other SHG Troubleshooting Guide 14 05 20 02
5. Intel Server Board SHG2 Troubleshooting Guide A Guide for Technically Qualified Assemblers of Intel Identified Subassemblies Products Revision 1 1 May 2002 INTal SHG Troubleshooting Guide 1 05 20 02 Disclaimer THE INFORMATION IN THIS DOCUMENT IS PROVIDED AS IS WITH NO WARRANTIES WHATSOEVER INCLUDING ANY WARRANTY OF MERCHANTABILITY FITNESS FOR ANY PARTICULAR PURPOSE OR ANY WARRANTY OTHERWISE ARISING OUT OF ANY PROPOSAL SPECIFICATION OR SAMPLE Information in this document is provided in connection with Intel products No license express or implied by estoppel or otherwise to any intellectual property rights is granted by this document Except as provided in Intel s Terms and Conditions of Sale for such products Intel assumes no liability whatsoever and Intel disclaims any express or implied warranty relating to sale and or use of Intel products including liability or warranties relating to fitness for a particular purpose merchantability or infringement of any patent copyright or other intellectual property right Intel products are not intended for use in medical life saving or life sustaining applications Intel retains the right to make changes to its test specifications at any time without notice The hardware vendor remains solely responsible for the design sale and functionality of its product including any liability arising from product infringement or product warranty Copyright Intel Corpor
6. a ATA devices with other devices on the same IDE channel cccceeee Intel Server Board SHG2 Issue Report sscsscscsssssssssssssscesssscssssssssesssssssesssssssecsassscesssssssecssssssesssssesess SHG Troubleshooting Guide 3 05 20 02 es 5 is 6 ashes 6 et 7 tee 7 TER 8 hei 9 al 9 pit 9 Aah 9 Ash 9 10 10 10 10 10 10 10 SHG2 Troubleshooting Welcome to the SHG2 server platform In the unlikely event you do encounter issues this guide will help you troubleshoot amp identify possible problem areas If you are unable to resolve a problem using this guide please call Intel Customer Support This guide will help you collect the data we will need to help you through your issues Each issue includes suggestions that may help you and a list of information we will need to assist you should you need to call Please visit the Intel Support website for updated versions of this document http support intel com support motherboard server SHG2 SHG Troubleshooting Guide 4 05 20 02 Boot Issues 1 My server will not power on Check for the following possibilities e The SHG2 server board requires an ATX 12V power supply A momentary switch should be used for the power on off switch and the sleep resume switch The power supply chosen must meet the ATX 2 01 or later specification Does your power supply meet these criteria e Have you securely plugged the server AC
7. able the onboard LAN Onboard features can be disabled through Server Board SHG2 BIOS setup Memory Questions 1 What memory configurations are supported on the Intel Server Board SHG2 Server Board SHG2 has slots for six 184 pin registered DDR 200 266 ECC SDRAM The SHG2 server board can support a minimum system memory configuration of 256MB two sticks of 128MB and a maximum system memory configuration of 12GB Server Board SHG2 supports SDRAM sizes of 128MB 256MB 512MB 1GB and 2GB single or double sided Memory sticks must be identical and populated in pairs 2 What kind of problems might occur in an SDRAM based system that uses non compliant DIMMs The most extreme example is memory failure when the system hangs while booting This can happen when the system is unable to communicate properly with the memory In less extreme cases the memory may generate intermittent errors or fail during stress Always use memory from the Intel Server Board SHG2 Tested Memory List for maximum reliability http support intel com support motherboards server SHG2 SHG2 Troubleshooting Guide 9 05 20 02 Jumpers and BIOS Setup Options 1 Why can t find speed settings in my BIOS configuration mode The processor speed option previously available in configuration mode is not displayed with newer Intel processors and will not affect the processor speed Newer Intel processors boot with the frequency speed preset and are tested during manufac
8. ation 2002 Other brands and names are the property of their respective owners Revision History Orig Rev Description Date 1 0 First release May 2002 1 1 Corrected chassis product codes May 2002 SHG Troubleshooting Guide 2 05 20 02 Table of Contents SHG2 TroubleshootinG csccassesssssseocessesensnssnssedsscesensetonsavevesssonsnsenseedhercoeesesecdnsenserstonescosesuaseedasesso cessed ensudnnsavdees Boot ISSUES husani oina Eese i is oiie ian EEEIEE SSNS SEAE STRECE N S EE Tara 1 My server will Mot POWER ON cennsa a ai a a a a 2 Upon booting my server starts beeping esesesesssesssssesssessessstststststststststststststststsiststsestsesesesesesesesesests 3 My hard disk drive HDD lights went on I heard the drives spin up and my floppy drive light turned o but lminot seeing VideO reren else ees EEE Sestak Blea oh E OE oan nad 4 am installing adapters in my powered down system and my system boots up when install a PCI ACE PLS IAEE P E E E A E A cule A AE A A T E E po tavenagsene 5 My system boots up automatically when power on my power Strip ssesssssesessesesesessesesessesesreresese 6 Some of my hard drives show up during POST and some don t s s sssssssssesesesereresrsssssssssssrererseseerse Other QUESTIONS 3 incassinsisseiecsasctscessesscosesonscesesvesocsnsenssedereooe ceasehuedesaubeassessssutsocdasatbonsvasededsesenscetonessocdensnceboessesecsees Generali QUESTIONS r e seecsedhes
9. e Issue 2 e Please note what is displayed on the monitor or any sounds emanating from the server system e If the server will still not boot please fill in the issue report form at the end of this document amp contact your Intel customer support representative SHG Troubleshooting Guide 5 05 20 02 2 Upon booting my server starts beeping Most likely these beeps are beep codes They identify system events in case video fails to display The following gives a description of possible beep codes for this board Table 1 Beep Codes Beeps Reason One short beep before boot this is normal not an error Search for option ROMs One long two short beeps on checksum failure 1 2 2 3 BIOS ROM checksum 1 3 1 1 Test DRAM refresh 1 3 1 3 Test 8742 Keyboard Controller 1 3 3 1 Auto size DRAM system BIOS stops execution here if the BIOS does not detect any usable memory DIMMs 1 3 4 1 Base RAM failure BIOS stops execution here if entire memory is bad 2 1 2 3 Check ROM copyright notice 2 2 3 1 Test for unexpected interrupts 3 My hard disk drive HDD lights went on I heard the drives spin up and my floppy drive light turned on but I m not seeing video Check the following Make sure the monitor is turned on and the video cable is plugged in completely Remove all add in cards and retry booting with just the on board components If successful try adding the add in cards back into the system one at atime witha
10. e included issue report form and call your customer support representative Please pay special attention to the following information What add in adapters do you have in your system manufacturer and model number What types of hard drives are in the system manufacturer and model number What kind of terminator do you have at the end of the cable Manufacturer and type e g Ultra 160 Note only the last device on the SCSI channel requires termination All LVD devices require active vs passive terminators What are the SCSI IDs of the devices on your SCSI bus How many SCSI channels are you using What memory is the system using Is it on the tested memory list Visit the Intel support site for an updated memory list http support intel com support motherboards server SHG2 SHG Troubleshooting Guide 8 05 20 02 Other Questions General Questions 1 What is Flip Chip Pin Grid Array FC PGA FC PGA is a processor package that was developed to improve the thermal dissipation of the heat generated by faster speed processors The die has been flipped so that the heat is directed away from the server board This feature when combined with active heat sinks is an optimal cooling solution 2 What type of battery is used in Intel Server Board SHG2 A standard coin cell 3 volt CR2032 or equivalent is used to supply power to the Real Time Clock RTC when power is not available from the power supply 3 How do I dis
11. nd have it ready Intel Server Board SHG2 Issue Report Please Complete All That Apply Company Name Date Submitted Contact Email Address Telephone Priority 1 Hot 2 Critical 3 High 4 Low Chassis 1 Intel Server Chassis SC5200 Base Lj Intel Server Chassis SC5200 HSRP Ly Other Manufacturer Part Number Power Supply Mfr Power Supply Part Number Type of Chassis Fans Quantity of Chassis Fans Fan Manufacturer Fan Part Numbers Problem Description Complete details of the problem setup problem description error messages recreation steps troubleshooting steps completed etc SHG Troubleshooting Guide 11 05 20 02 System Configuration Information Hardware Main Board Part Number PBA AA System BIOS Version BMC firmware version HSC firmware version SCSI Backplane PBA Processors Installed Quantity Processor Speed frequency Processor ID CPUID Memory Modules total number of DIMMs Size per DIMM please indicate MB or GB RAM Manufacturer and part number Is this RAM on the tested memory list If less than 6 DIMMs are installed which slot numbers are being utilized Operating System Operating System name amp version Language Service Pack SHG Troubleshooting Guide 12 05 20
12. ned the system off via the power switch on the front panel Additionally signals in the PCI connectors tell the system to boot normally used by server management adapters NICs Plugging in the adapter with the AC power cord still connected can cause false signals to be transmitted commanding the system to boot Before removing the cover to your chassis you should always e Turn off the server via the power switch on the front panel e Unplug the AC cord from the server 5 My system boots up automatically when power on my power strip Some server systems save the last known power state since the last AC power connection If you remove AC power before powering down the system via the power switch on the front panel your system may automatically attempt to come back to the on state it was in once you restore AC power e Please keep in mind that unplugging the system or flipping a switch on the power strip both remove AC power e Follow the correct A C removal sequence press the front panel button and then remove the A C power cord Allowing your system to fully power up and then power down the system using the front panel power switch should correct this problem If it does not fill out the attached issue report form and call your customer support representative Please have the following information available e What BIOS do you have loaded on the system The latest tested BIOS is posted to the Intel Customer Supp
13. ort Website e What is the PBA number of the server board The PBA number is located on a white label near the edge of the board and is printed in the following format PBA xxxxxx XXX e What memory is the server using Is it on the tested memory list Visit the Intel support site for an updated memory list http support intel com support motherboards server SHG2 What chassis and power supply is the system using SHG Troubleshooting Guide 7 05 20 02 6 Some of my hard drives show up during POST and some don t Check on the following Are you using third party SCSI adapters System memory limitations limit the number amp size of option ROMs in the system If you place too many adapters or adapters that take up too much space in memory they may not install and show the hard drives connected to them Verify that pin 1 on the data cable connects to pin 1 on the device In most cases if you orient the data cable so that the colored stripe on the cable is pointing towards the power connector on the device you will have proper orientation Verify that the device power cable is firmly connected Check your SCSI ID numbers SCSI devices must have their own unique ID on the SCSI bus This number must be set with jumpers on the device ID number should be set starting at 0 and must be set lower than 8 if booting from the drive Check for proper termination on the SCSI bus If your hard drives still do not show please fill out th
14. turing 2 How should the jumpers be set on Intel Server Board SHG2 A single configuration jumper on Server Board SHG2 is used to access BIOS configuration mode All configuration options are made available through the BIOS configuration screens Refer to the Technical Product Specification for more information on configuration jumper settings Input Output 1 Does the Intel Server Board SHG2 support Ultra ATA 33 66 100 hard drives Yes One of the features of the Intel Server Board SHG2 is its ability to support all Ultra ATA transfer rates i e 33MB sec 66MB sec and 100 MB sec To take advantage of the increased bandwidth available on the IDE channels a hard drive that implements higher spindle speeds and a large onboard buffer size may be required 2 What IDE cable should use to support both Ultra ATA 100 and previous IDE transfer protocols A 40 pin 80 conductor cable can be used with Server Board SHG2 and is fully backward compatible with all IDE transfer protocols It will also support Ultra ATA 100 if used with one or two Ultra ATA 100 drives attached 3 Can I mix Ultra ATA devices with other devices on the same IDE channel Yes However for better performance we recommend that the Ultra ATA capable devices be attached to their own IDE channel separate from other non Ultra ATA capable drives SHG Troubleshooting Guide 10 05 20 02 If you must contact customer support please fill out the following support form a
Download Pdf Manuals
Related Search