Intruder alarm system Operating Instructions
Contents
1. beep 12 3 4 5 6 TAPA O000000 m Exit beep E insistent Exit beeps for final 10 seconds Power ote 8 O Day The Day indicator should be lit at the Panel Offer a keyfob to the Panel and withdraw it as soon as you hear the keyfob recognition beep tone from the local sounder Note the panel LEDs will flash consecutively from right to left PA to Zone 1 LED during Set operation If however there is an open zone then the relevant ZONE LED will be lit and a sound indication is given If this is the case then investigate the cause and ensure all zones are closed The system will produce the exit beep tone and you should leave the premises by the exit route recommended by your installer The system will set when the exit beep tone stops The external strobe will operate for 5 seconds which provides a confirmation of the SET operation Once any operation is performed using the keyfob withdraw it away from the panel wait for 3 seconds duration before next use of the keyfob to operate the system Logic Six intruder system How to Unset the system When you enter your premises you will need to unset or turn off the system If your system had gone into alarm then be aware that intruders may be in the premises Seek assistance before investigating the cause of the alarm and unset the system M Entry beep Power vie one 2 3 4 5 6 TAPA WOOO aa Offer keyfob to th2. cause and ensure the open zone s are closed Once any operation is performed using the keyfob withdraw it away from the panel wait for 3 seconds duration before next use of the keyfob to operate the system Logic Six intruder system Entry time Area Zone name Full set Part Set protected Zone 1 T Zone 2 TI Zone 3 I TI Zone 4 I I Zone 5 I I Zone 6 I O O Omitted T Timed Entry Exit Zone TI Time Inhibited Access zone to panel I Immediate Zone armed to give full alarm Operating instructions CED Declaration of Conformity The Logic Six panel is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC This product is intended for use in the UK 8 4188 753 issue 2_2 03
3. Intruder alarm system Logic SIX Operating Instructions f 1 12345656P a OOQOO00000 _ O Em O Learn i O Error a O Day IO en C Logic Six CO Se O Servicing organisation Installer name Telephone number Date of installation Account number Operating instructions System installation This booklet tells you how to operate your intruder alarm system To simplify this booklet we have assumed that the alarm system has been installed by a professional intruder alarm system installer the installer and that the system is operated in a typical way Aspects of your system that are not typical will be described by your installer Q If you have any questions about your intruder system then consult your installer see contact details on the front page To operate the alarm system you will need the keyfobs supplied with the panel These keyfobs are recognised by the panel and will operate your system If you should need further keyfobs you should consult your installer up to 8 maximum keyfobs can operate your system Keyfobs Supplied with the panel oa pep ne ee Additional keyfobs ae amp lt a Go xO Logic Six i
4. e Panel Panel and withdraw M Keyfob recognition beep Kenr beep Power 1 i vie als bda is e x Enter your premises by the route recommended by your installer Depending on the setting of your system you now have either 15seconds or 30 seconds to unset the system from the time you hear the entry beep tone Note the panel LEDs will flash consecutively from left to right from Zone1 to the PA LED during Unset operation Offer a keyfob to the Panel and withdraw it as soon as you hear the keyfob recognition beep tone from the local sounder The system will stop the entry beep tone and the consecutive flashing of LEDs The green Day LED is lit to indicate the system is unset 9 n TA PA 1 vie vie sie 8 9 8 If any Zone Tamper or Attack LEDs light up then an alarm has occurred and an intrusion may have taken place Seek assistance before investigating further as intruders may still be on the premises The first alarm indication given by a flashing indicator with all subsequent alarm indication given as a steady indication These indications will remain until the next time the system is set Operating instructions How to part set the system If your installer has programmed your system for part set operation you will be able to set some zones of the system while others remain unset Part set operation is often used at night time and it will permit you to freely wal
5. k around the bedrooms while the living area and outside doors are protected Before part setting the system at night time you should ensure the downstairs of the premises have been completely vacated and that all doors and windows are closed Ensure that pets do not have access to the protected areas as they can cause a false alarm Power Offer keyfob to the Panel Panel and withdraw 12 3 4 5 6 TA PA OOOQOOOCwS E Keyfob recognition beep E Exit beep Within 10 seconds offer keyfob second time to the Panel and withdraw Day i E Keyfob recognition beep Ex beep E 2 x Set beep when panel is set Power ele 0 O Day The Day indicator should be lit at the Panel Offer a keyfob to the Panel and withdraw it as soon as you hear the keyfob recognition beep tone from the local sounder Note the panel LEDs will flash consecutively from right to left from PA to the Zone 1 LED The panel will produce the exit beep tone Within 10 seconds offer a keyfob a second time to the Panel and withdraw it you will hear another keyfob recognition beep The exit beep and consecutive flashing of LED will have stopped The Day LED should be flashing at the Panel You should now move to area omitted by part set The system will set after 30 seconds when two consecutive beep is emitted and the Day LED is no longer lit If ZONE LEDs remain On continuously and the system does not set investigate the
6. ntruder system Personal Attack If you are under threat or are being attacked you can activate the alarm by operating the personal attack button in your system The alarm system will produce a loud alarm sound and the external siren will be turned on Power Indicato The Power indicator on the control panel will light whenever the mains power supply is present If mains power fails then the Power indicator will flash but the system will run from its backup battery for several hours If the Power indicator goes out when mains power is present then a fault may have developed on your system and you should contact your installer Key lt LED steady On indication LED flashing indication O LED Off Internal sound Sound description NOTE In general a flat beep is an indication of not recognised keyfobs External devices Ww Strobe On A External Siren Operating instructions How to Set the system When you leave your premises you will need to set or turn on the intruder alarm system Before setting the system you should ensure that the premises have been completely vacated and that all doors and windows are closed Ensure that pets do not have access to the protected areas as they can cause a false alarm unless pet immune detectors have been used ask your installer for more information Offer keyfob to the Panel Panel and withdraw m Keyfob recognition
Download Pdf Manuals
Related Search