PROGRAMMING & OPERATING INSTRUCTIONS
Contents
1. 2 Press and hold the device button for about 3 seconds until the device s LED indicator blink once then release the device button and LED will light up again 3 Press the POWER button then follow the sequence to enter the 3 digit code that you noted from the Device Brand Code List 4 If the code is correct the LED indicator will blink four times and turn off You can now use the remote to operate your device 5 If the code number is not on the list the LED indicator will flash four times then stay lit so please go back to the step 3 and program the remote again NOTE 1 During the set up state you can press the Exit button to exit this mode and the LED indicator will blink four times then turn off 2 If you have not pressed any button during 20 seconds the device button will blink twice and turn off 2 AUTOMATIC CODE PROGRAMMING If you are not able to control your device after code entry or you are not able to find the brand and code in the Device Brand Code List please use this function to source the code that you need 1 Turn on all devices such as TV DVD VCR SAT you would like to program the remote to operate Press and hold the device button for about 3 seconds until the device s LED indicator blink once then release the device button and LED will light up again N Press the PLAY button to enter Automatic Code Programming and the led will blink continually Every 1 5 seconds2. GUIDE If you are unable to use any of the program device codes and your original remote can still be used you can use the learning function to copy the codes from your original remote to the URC6D remote Please follow the step set out below to use this feature 9 JN I 3 QI N amp N QI amp Q N 9 9 3I h QI 3 QJ N 9 LEARN THE CODE TO YOUR REMOTE CONTROL 1 Press and hold the device button down for about 3 seconds then release it the led will be light up 2 Press the REC button to enter the learn state the led will blink once 3 Place the original remote control and your URC6D on a flat surface with the infrared windows facing each other making sure you keep them within 5cm of each other Press the button that you would like to learn on your URC6D 4 Press the button that you want to learn on the original remote control the device button led will blink four times slowly then the will stay lit to show learning was successful NOTE The LED will blink quickly if the learning function fails This is usually due to poor alignment of the remote controls 5 Repeat steps 3 to 4 above and learn all buttons of the current device you wish to learn in your remote control If the LED blinks four times and leaves the learning mode automatically it means the memory in the remote is full You will need to delete some of the learnt keys then try the learning process again 6 After you have finished learning
3. to set up you device code on the remote control 1 Turn on all devices such as TV DVD VCR SAT that you want to program the remote to operate 2 Press and hold the device button for about 3 seconds until the device s LED indicator blink once then release the device button the LED will light up again 3 Type in the Brand code that you found in the list to enter the Brand Search function the led will light up 4 Once every 1 5 seconds this remote will transmit a code of POWER or PLAY or CH or MUTE automatically and the led will blink continually When the device to be power off or play DVD CD VCR or displays operate indication such as CH for TV SAT CBL and MUTE for AUDIO press the device button to save and exit and the LED will blink four times then turn off NOTE 1 The remote will continue to search unless you press the device button to save the setup or press the EXIT button to stop the search and exit without saving BRAND CODE SEARCH LIST TV Brand Brand SAT Brand VCR Brand DVD Brand Philips 00 Philips 10 Daewoo Thomson 11 Vestel Sony 12 Sanyo LG 13 Bush JVC 14 Clatronic Samsung 15 Audioaonic Panasonic 16 Orion Akai 17 Firstline Hitachi 18 Mitsubishi Toshiba 19 Pioneer Philips Thomson Strong Skymaster Technisat Nokia Tevion Pace Grundig Finlux Philips Thomson Sony LG JVC Samsung Panasonic Goodmans Hitachi Toshiba Daewoo Grundig co 4 LEARN FUNCTION OPERATION
4. universal remote control as they could leak and void your warranty e Always replace all batteries at the same time do not mix old and new batteries or mix different battery types Take care when disposing of exhausted batteries please consult your local council or recycle department for nearest collection point Do not drop or throw your universal remote control as you may damage the unit and the circuitry inside Do not let the remote control come into contact with any liquids e Use a dry cloth to clean your universal remote control INSTALLING REPLACING BATTERIES Install two new AAA batteries as indicated by the diagram in the battery compartment When the batteries become low and need to be replaced please replace the batteries by following these steps as below a Push the catch on the battery cover upwards and pull the back cover off the main part b Carefully remove the old batteries then insert the new batteries matching the and signs c Once the batteries are in put the cover back on making sure the catch clicks into place NEW URC6D INSTRUCTIONS2 indd 2 10 01 2012 10 00 u PROGRAMMING THE REMOTE CONTROL TO CONTROL ADDITIONAL DEVICES 1 MANUAL CODE ENTRY PROGRAMMING Find your brand and model of TV in the separate Device Brand Code List booklet and note the 3 digit code 1 Turn on all devices such as TV DVD VCR SAT you would like to program the remote to operate
5. MAXVIEW PLATINUM QUALITY RANGE URC6D PROGRAMMING amp OPERATING INSTRUCTIONS To have clearer idea of the features and capabilities of your remote control take a moment to read these instructions Please do not discard and save for future reference oO o n S Qa ies E gt e O lt O 2g PLAY PAUSE STOP 2 A m i lt al ALL OFF MUTE MI DISTANCE J i E 8 i N SLEEP BASS TREBLE zoo Please note Not all functions are guaranteed to work depending on your brand of TV NEW URC6D INSTRUCTIONSZ indd 1 10 01 2012 10 00 A INTRODUCTION The URC6D is already programmed to control various devices in your home The remote control is simple to program easy to use and can operate up to six electronic devices which include TV TV including HDTV Plasma and LCD TV DVD Combo TV VCR Combo DVD VCR DVDs include DVD player DVD R DVD combo HDD and DVD Home Cinema VCR DVD DVD R HTIB DVD VCR CBL Cable Cable PVR DVR Video Accessories Including Media Center PCs SAT Satellite Satellite PVR DVR Video Accessories Including Media Center PCs CD CD Home Automation CD R Recorders AUDIO Tuner Amplifier Misc Audio HTIB Home Theatre In A Box URC6D transmits to each of the above electronic devices using an infrared IR signal Before you use this remote control to operate your devices listed above it must first be programmed
6. MMING D You can re program the MACRO buttons on this remote control to carry out a sequence of individual commands with only 1 key press MACRO BUTTON PROGRAMMING Good example of a Macro function TV turn on switch TV to AV mode DVD turn on Play DVD player 1 Press and hold the MACRO button for about 3 seconds then release it to enter this feature and the LED indicator will light up 2 Then press TV button POWER button AV button DVD button POWER button and PLAY button last press the MACRO button to save and exit 3 Now if you press the MACRO button the remote control will auto turn on your TV and switch the TV to AV input source then turn on your DVD player and play your DVD NOTE 1 You can only programs a maximum of 16 buttons with this feature If you use more than 16 the device button will blink twice and go out automatically 2 In this feature you must press the device button first when you program the MACRO button DELETE THE MACRO BUTTON PROGRAMMED 1 Press and hold the MACRO button for about 3 seconds then release it to enter this feature and the LED indicator will light up to enter this feature 2 Press the device button twice 3 The led will blink 4 times and go out to show that the delete has been successful NOTE 1 You can only programs a maximum of 16 buttons with this feature If you use more than 16 the device button will blink twice and go out automatically 2 In this featur
7. all the keys that you want press the EXIT button to exit NEW URC6D INSTRUCTIONS2 indd 4 10 01 2012 10 00 DELETE A LEARNT KEY 1 Press and hold the device button for about 3 seconds then release it the LED indicator will light up 2 Press the Exit button to enter this feature 3 Then press the key that you want to delete and the Led indicator will blink 4 times 4 Repeat above steps to delete other learnt keys that you want 5 Press any device button to exit out of this feature and the LED indicator will blink 4 times DELETE ALL LEARNED KEYS OF A DEVICE 1 Press and hold the REC button for about 3 seconds then release it the LED indicator will light up 2 Press the device button that you want to delete the learnt keys of 3 After successful deletion the Led indicator will blink 4 times and go out 4 In this feature you can press the EXIT button to stop the operation and exit DELETE ALL LEARNED KEYS 1 Press and hold the REC button for about 3 seconds then release it the LED indicator will light up 2 Enter the operation code 000 to enter this feature 3 After successful deletion the Led indicator will blink 4 times and go out NOTE Please notice that some buttons cannot support this feature which include All device keys all operation keys include ALL OFF EXIT MACRO FAV CH BASS TREBLE NIGHT buttons for TEXT REPEAT PREVIOUS NEXT SHU and TTX OFF MACRO BUTTONS PROGRA
8. e you must press the device button first when you program the MACRO button 3 If you need to program the MACRO button again you must delete the programmed first 4 In this feature you can press the EXIT button to exit without saving NEW URC6D INSTRUCTIONS2 indd 5 10 01 2012 10 00 E FAV CH BUTTON PROGRAMMING This feature is only for TV SAT and CBL device You can program this button to work as you setup A setup example for the FAV CH button 2 5 6 8 1 Press and hold the FAV CH button for about 3 seconds then release it to enter this feature and the LED indicator will light up 2 Then press 1 button 5 button 6 button 8 button last press the device button to save the FAV CH button programmed and then press EXIT button to go out 3 Now if you press the FAV CH button the remote control will auto switch your TV s channel step by step as you have programmed DELETE THE FAV CH BUTTON PROGRAMMED 1 Press and hold the FAV CH button for about 3 seconds then release it to enter this feature and the LED indicator will light up 2 Press the device button twice 3 The led will blink 4 times and go out to show that the delete has been successful NOTE 1 You can programs maximum 6 buttons on this feature If more then the device button will blink twice and go out automatically 2 In this feature you can press the EXIT button to not save and go out TRANSPORT PUNCH THROUGH FUNCTION In this feature if
9. e remote control will step through the channels by itself 2 Press the CH or CH buttons again to exit this feature CHECKING THE CODE NUMBER You can use this feature to check the three digit code for your programmed device follow these steps using the remote control keypad 1 Press and hold the device button that you would like to check such as TV keep the button pressed for about 3 seconds then release it and the device led will light up 2 Press the INFO button and the device led will blink once 3 The device button will then blink a number of times in three groups to indicate the original code number You will need to make a note of this number NOTE 1 If the digit code number is 0 the device led will fast blink once 2 After the led has blinked the first number of the three digit code there will be a gap of 1 5 seconds the led will blink again for the following numbers For example for three digit code is 095 then 0 The led will fast blink 1 time the led turn off 1 5 seconds 9 The led will blink 9 times the led turn off 1 5 seconds 5 The led will blink 5 times the led turn off and go out 10 01 2012 10 00 URCEDINS Iss 1 8 NEW URC6D INSTRUCTIONS2 indd 8 10 01 2012 10 00
10. er function Number Keys Function TTX Function NUMER_1 TTX PAGE NUMER_2 TTX PAGE NUMER_3 TTX REVEAL NUMER_4 TTX INDEX NUMER_5 TTX HOLD NUMER_6 TTX EXPAND NUMER_7 TTX CANCEL NUMER_8 TTX SUBPAGE NUMER_9 MIX NUMER_0O REPEAT RED REW GREEN FF YELLOW SHUFFLE BLUE NEW URC6D INSTRUCTIONS2 indd 6 10 01 2012 10 00 NEW URC6D INSTRUCTIONS2 indd 7 a Se PIP PICTURE IN PICTURE SHIFT FUNCTION In this feature you can switch the navigation buttons to control the PIP function of the TV If you press the PIP button first the navigation buttons will then control the PIP function of TV press the PIP button again to exit this feature The list below shows the keypads PIP equivalent functions If the remote control is using the PIP function you can press the SWAP button to switch between both PIP and the navigation function Number Keys Function TTX Function Arrow_Right PIP Arrow_Left PIP MENU PIP SIZE INFO PIP POS Arrow_Up PIP SOURCE Arrow_Down PIP FREEZE QUICK VIEW CHANNEL FUNCTION With this feature you will be able to quickly view the channel on the TV SAT or CBL device stepping quickly through the channels without the need to press any buttons Please follow the steps below to use this feature Press and hold the CH or CH button down and keep pressed for about 3 seconds then release it the device LED will light up to show it has entered this function Every 1 5 seconds th
11. set up BEFORE SETTING UP LEARN You can copy any of the button functions of the original remote control to this remote control ALL OFF The remote will transmit to all programmed devices POWER to turn on off your devices MACRO BUTTON You can re program the MACRO buttons on this remote control to carry out a sequence of individual commands with only 1 key press DEVICE CODE CHECKING You can use this feature to check the four digit code for your device if you have forgotten it VOLUME PUNCH THROUGH D Volume control keys include VOL VOL MUTE keys You can use these keys direct to co control your VCR DVD VCD CD AMP etc multi devices through your TV SAT CBL operation state do not switch remote control mode TRANSPORT KEY PUNCH THROUGH Transport keys include PLAY REW FF REC STOP PAUSE keys you can use these keys directly to control your VCR DVD VCD CD AMP etc even when the device mode you have selected is TV SAT CBL without switching device modes Before you use the universal remote control with the device that you would like to control it must first be programmed set up Please read this guide carefully to make sure the setup is carried out correctly and please make sure you have read the information below Point your universal remote control directly at the infrared part of your device e Ensure there is nothing blocking the infrared receiver on your device Do not leave flat batteries in your
12. the remote will transmit a code of POWER or PLAY CH or MUTE automatically When the device to be programmed responds to a POWER PLAY CH or MUTE press the device button to save and the LED will blink four times then turn off NOTE 1 In this feature You can press PAUSE button to pause automatic code search and press again to continue searching 2 After you have paused the search you can press FF to forward search ten codes and press REW to rewind search ten codes of the library to find out a better device code 3 After pause searching You can press CH to forward search to the next code and press CH to rewind search to the previous code one by one 4 During the code search feature you can press EXIT button to stop the search and exit but the searched code will not be saved and then the led will blink four times and turn off 5 When the remote has finished cycling through all the codes the led will blink four times you can then either go through the process again or press the EXIT button to finish searching 6 The remote control will exit without saving if any keys are pressed after paused search or searched a cycle through the full database NEW URC6D INSTRUCTIONS2 indd 3 10 01 2012 10 00 I 3 BRAND SEARCH CODE PROGRAMMING You can use this feature to set up the device code quickly Please find your device brand on the below Brand Search Code List then follow these steps below
13. your remote control previous working device is DVD VCR CD in the TV SAT CBL working mode you do not need to switch the working mode you can under the working mode direct control the Transport buttons include FF REW PAUSE PLAY STOP REC button for you DVD VCR or CD device But if the Transport buttons can be control the device self this feature will be disabled VOLUME PUNCH THROUGH FUNCTION In this feature if the last device the remote was used with was either TV or AUDIO when in DVD VCR or CD mode you will not need to switch back to the previous device You will have direct control of the DVD or VCR or CD mode control with the addition of the Volume buttons include Volume Volume and Mute button for the TV You can follow these steps as below to enable this feature 1 Press and hold the device button that you want to setup about 3 seconds then release it to enter this feature and the LED indicator will light up 2 Then press the VOL button and the led blink twice and go out TTX SHIFT FUNCTION In this feature you can switch the number buttons to control the Tele Text Mode of the TV In the standard state the number buttons will be used to control the channel change of the TV if you press the TTX ON button first the number buttons will then be controlling the Tele Text Mode of TV The list below shows the keypads text equivalent You can press the TTX OFF button to switch back to the channel numb
Download Pdf Manuals
Related Search