R E G E N T CODE REF: MW-SENO1 TROUBLESHOOTING
Contents
1. 3 L4 pull switch to the ON position as 1 pull switch to the OFF position as 0 switch location and detection range of the corresponding table is as follows Detection range setting S1 S2 S3 Detection range is the term used to describe the radii of the more or less circular detection zone produced on the ground after mounting the sensor light at a height of 2 5m pull switch to the ON position as 1 pull switch to the OFF position as 0 switch location and detection range of the S4 The settling time is the time that the light remains on before entering ine norma S4 a ime LiM s v Settling time setting a detection condition pull switch to the ON position as 1 pull switch to tne OFF position as 0 the position of the switch and corresponding time shown as the right chart Time setting P S5 S6 S7 S8 The light can be set to stay ON for any period of time between approx asec anc S5 S6 S7 a maximum of 30 min Any movement jetected before this time elapse will re start the timer Itis recommended to select the shortest time for adjusting the detection zone and for performing the walk test Pull switch to the ON position 4 pull switch to the OFF positon a switch location and detector tange corresponding table is 25 how s aj G eki M iv uw t i 4 REGENT SPECIFICATIONS Power source Power frequency Rated load HF system Insta2. MICROWAVE SENSOR CODE REF MW SENO1 REGENT TROUBLESHOOTING Cause wrong light control setting selected Adjust setting load faulty e Change load mains switch OFF e Switch ON e continuous movement in the detection The load will not work The load work always e check zone setting zone The identifiable movement load work without any the sensor not mounted for detecting securely mount enclosure movement reliably movement occurred but not identified Check zone setting by the sensor movement behind wall movement of a small object in immediate lamp vicinity etc The load will not work despite rapid movements are being suppressed Check zone setting movement to minimize malfunctioning or the detection zone you have set is too small 1 Being installed in the rocking object will lead to misoper tion 2 The shaking curtain which is blown by wind will lead to misoperation please select the suitable installed place 3 Being installed in the place where the traffic is busy will lead to misoperation 4 Iit will lead to misoperation when there are sparks produced by some equipment nearby The detection distance may multiply for the reflection on microwave Sectromagnenc eid Dy the metal or glass materials Thus lower the sensitivity to reach the appropriate detection distance Newer turn the SENS knob to the maxim
3. as shows below you can change a common light to an automatic light UTILIZED IN CEILING LIGHT This product can be utilized in more fields than the above examples You can also install a MW SENO0 1 in the ceiling directly to control an aisle There is no problem 1 The product can not work normally if there is metal material behind NON METAL MATERIAL the Installed place when the sensor is installed inside the ceiling floor the sensitivity to light will be invalid This product will be faithfully waiting for you lt will turn on the light automatically when you pass by and turn off the light automatically when you leave off You can set the closing delay time to meet your needs For example you may adjust the TIME sliding controller to select the delay time 12sec 30min when you think you will come back in 10mins The TIME sliding controller is as follow Keep away from the detecting zone after adjusting the testing time or that the detecting time will be inaccurate when any moving object is detected again by the product PARAMETER SETTING Photosensitive sensors Light control setting _ _ i L1 L2 L3 L4 Sensor lights j E y Time setting S5 S6 S7 S8 Setting time setting S4 Detection range setting S1 S2 S3 p The total power of incandescent lamp can not exceed 500W The tota power of CFL can not exceed 200W
4. llation sit Transmission power Detection ang Detection range MICROWAVE SENSOR 73mm 220 240V AC 50Hz 500W Max tungsten cos 1 200W Max fluorescent coso 0 5 5 8GHz CW radar ISM band Ceiling mounting Wall installation lt 0 2mW 360 Ceiling installation 180 wall installation 1 12m radii adjustable le Arn Time setting 8sec 30sec S0sec 6min 20min 30min adjustable Light control 1OLUX 25LUX S0LUX 7 50LUX 2000LUX adjustable Standby power Approx 0 5W SENSOR INFORMATION UTILIZING FIELD AND INTRODUCTION MW SENO is a moving objec sensor that can detect range of 360 and it s working frequency is 5 8G The advantage of this product is stable working state stable 10 C 80 Ees safe and performs Detter than infrared sensor 65mm CODE REF MW SEN01 r A BEBE BRSBAREA 58mm Transmission power lt 0 2mW NOTE the high frequency output of this sensor is lt 0 2mW that is just one 5000 of the transmission power of a mobile phone or the output of a microwave oven Sensing angle adjustment range working temperature MW SEN01 2copts a microwave sensor high frequency outo ut lt 0 2mW so that it is MICROWAVE SENSOR CODE REF MW SENO1 REGENT It can be installed inside of product that is made of glass and plastic because that these materials make little effect to microwave Connect the product
5. um value to avoid error detection Also the surrounding environment will lead to error action e g the automo biles passing by or the wandering objects caused by the wind Products should be installed more than 4 meters one from the other otherwise the interference among them will cause error action The proper use of trimming potentiometer ine tr mming potentiometer is used to adjust the time that sensor gnt turn on when detects somebody movement anc turn of automatically The user can adjust the light time according to different needs In order to carry out the saving energy effectively we suggest that we should decrease the close time automatically In addition due to the continuous sensor function of tne microwave sensor amp simply speaking Timer will time renewedly so as sensor lamp has any induction Lamp will keep open once Getected movement within the Dm detection range We are committed to promoting the product quality and reliability however all the electronic components have certain probabilities to become ineffective which will cause some troubles When designing we have paid attenton 10 redundant designs and adopted safety quota to avoid any troubles l This instruction without our permission should not be copied for any other purposes RE G E N T oR CODE REF MW SENO1 Light control setting Li L2 L3 L4 a g o o o o The chosen light response threshold can be infinitely from approx 10 2000 lux L1 L2 L
Download Pdf Manuals
Related Search