, First Installation Guide & Troubleshooting ' “ “x
Contents
1. SD right blind ports transmitter use the left blind port card to the transmitter use the right blind port Unscrew the blind port Screw the antenna and connect antenna to module Connection to PC Connection to PC via RS232 module via USB module Connect transmitter to PC with standard USB cable Connect cable to PC to serial RS232 communication port 7 THE FIRST POWERING UP OF THE FLOWMETER arkon Ly o systems After switching on the transmitter the display should appear like this TRANSMITTER Set up in user menu electrode cleaning and confirm Go to clean time and confirm Go to start now and confirm TRANSMITTER Y A Y Set up 300s and confirm A A Set up confirmation and confirm then go back to main display St art Now Pi 0300 ciean time After switching on run automatic electrode cleaning for about 5 minutes 0 000000 Total m3 O TO gt Contact Support Information required Serial number of the flowmeter FW version SW version fault description photos of installation if applicable Technical support support arkon co uk BUREAU VERITAS pa Windows Live Messenger support arkon co uk Sor i po Telephone 420 543 214 822 A i AA e Version 07 2012 4 A E ie2. First Installation Guide amp Troubleshooting gt e o ra WW W arkon couk a o an cos 1 Made in s www arkon co uk r KO Arkon Flow Systems P zova 1 3 602 00 Brno Czech Republic 1 systems Tel 420 543 214 822 Tel Fax 420 543 215 249 Enquiries Orders General questions office arkon co uk Marketing support Brochures marketing arkon co uk Technical support support arkon co uk www arkon co uk First installation Ge SENSOR SOAKING Soaking of the sensor Nuts and under operational conditions bolts must Before first intallation with a wetted full pipe be tightened soak the sensor liner correctly for 24 hours 2 SENSOR INSTALLATION Electromagnetic flowmeters only work correctly under certain determined conditions For our right to guarantee the product all those conditions have to be met in all applications Those conditions are achieved by the correct installation of the sensor Flowmeter sensor must always remain full of liquid For horizontal mounting locate the For vertical mounting flow sensor in a low section of the pipe direction must be upwards wa US For installations with pumps never install the For installations with valves correct location sensor on the suction side of the pump for the valve is downstream of a sensor RSA a Laminar flow is required to guarantee the accuracy of the readings Sensor must be installed When using pipe reducers in a sec
3. able gland inside the housing to guarantee proper sealing of the cable gland ond at MUNUM The female part must be All three power supply properly tightened with conduct must be a spanner or similar properly tightened b Connection of sensor Yellow B f Green A Brown 24V White GND TRANSMITTER Preparing connections Close the terminal box Transmitter part All connections must be properly tightened Connection to motherboard Warning connection between the power supply module and the motherboard is protected with a lock SENSOR Connecting cables Tightly secure the terminal box 5 INSTALLATION OF MODULES B GSM SMS RS232 RS485 i J e C E 4 20mA Each module has its own slot in motherboard Example of installation 4 20mA Current Loop Module Each module has visual lock Correct module Cable connection Cable connection installation to the module Setup in user menu current loop and YA confirm Go to setting signal A and confirm Flow Qn Invert Flow Current Loop Voltage Output Relay2 Go to fixed to make verification 10mA aA and confirm If 4 20mA Current Loop module is connected correctly you can measure 10mA on Output 6 CABLE SD CARD AND ANTENNA CONNECTION Connection to PC by cable and SD card connection Unscrew left and For connecting the cable to the For connecting
4. tion of straight they have to be installed pipe with minimum 5 before and after the straight times the pipe diameter 5xDN pipe section The angle of upstream and 3 times iz the slope of the reducer downstream should not exceed 8 3 GROUNDING a PLASTIC PIPE Grounding with earthing rings Washers must be used for earthing ring installations Ensure continuity of earth between sensor ring pipe and liquid You must use a conductor with a minimum cross section of 1 5 mm of Copper wire for all grounding Remember to connect the main grounding cable to the sensor neck Nuts and bolts must Earthing rings must be be tightened using a used for plastic pipe spanner Finger tight installation has no effect meee SOULE GH E A Be ean e for b have to be respected b CONDUCTIVE PIPE Grounding without earthing rings Contact point must be properly cleaned from rust paint etc CABLE CONNECTION a Connection of power supply See also the installation operational manual Unscrew blue cable gland Pull the cable through the cable gland by the insulation Pass the cable a You must use a cable through screw with a round cross section female part of b You must use a cable the cable gland with 3 conductors twin and earth The overall insulation Screw the female of the cable must be part to c
Download Pdf Manuals
Related Search