OPERATING INSTRUCTIONS
Contents
1. Page 27 of 33 MNYASM328S_0648 1 Matrix and 2 Slaves VIDEO INPUTS VIDEO INPUTS 17 48 49 80 KEYBOARD 1 i e 7 CONNECTOR EL VIDEO OUTPUT 8 CONNECTOR LE Video inputs e Master matrix from 1 to 16 e Slave matrix no 1 from 17 to 48 e Slave matrix no 2 from 49 to 80 Connection cable is described in Aux Line Slave s outputs are connected to Master s inputs according to this table Page 28 of 33 MNYASM328S_0648 Slave 1 output Master input Slave 2 output Master input 1 17 1 25 2 18 2 26 3 19 3 27 4 20 4 28 5 21 5 29 6 22 6 30 7 23 7 31 8 24 8 32 Event log The matrix supplies a series of information via the RS232 channel for recording the succession of significant events occurring to the system This log file is also extremely useful for identifying the cause of faulty operation due to errors when setting up the matrix The log can be sent either to a serial printer or to a Personal Computer for subsequent processing in the latter case amp Warning Serial printers are usually provided with a reception buffer DEUNA will only commence when the buffer is full Before removing the paper from the printer force the printer to print the outstanding buffer following the instructions given in the user s manual for the printer Usually OFFLINE forcing followed by page feed is sufficient to empty the buffer Each event ha2. VPETA UNG INSTRUCTIONS 1 Introduction 1 Typographical conventions 2 Safety rules 2 System installation 1 Preliminary operations l Zo 3 Opening the package Checking the markings Switching on and off 1 Switching on 2 Switching off 2 Connectors and cables onaurwn Video cables Keyboard lines Direct Telemetry control DVR and direct coax Telemetry control Aux Line Personal Computer and Serial Printer Cable BNC for the Alarm Reset Relay and alarm connectors 1 Electrical specifications of the alarms 2 Electrical specifications for the relays 3 Jumpers and DIP l 2 Opening the matrix Dip Switch Configuration l System configuration and baud rate 2 Restoring the settings 3 Updating the firmware 4 Maintenance 3 Setup 1 L 2 3 Notes regarding the menu system Matrix Setup Setup by On Screen Menu 2 Entering Program Mode l DCT Keyboard 3 Setup Parameters 1 2 3 Date Video system 1 Removing Texts and Masks Simplify Menu 1 Day and Night Periods External Contacts 1 Weekdays 2 Single day Festivities 3 Holidays Periods Time 1 Daylight Saving Time Enabling the keyboards Page 1 of 33 MNYASM328S_0648 7 Control Monitor 1 Messages on the Control Monitor 2 Excluding video inputs 8 Cameras ID Texts 9
3. If a sequence is empty the cameras have not been defined fixed camera 1 will be shown Menu 4 2 After choosing the sequence to define or modify press Enter to enter the edit submenu Inside the edit submenu scroll through the 32 available steps with Inc Dec and request a change by pressing Enter enter the time from 1 to 600 seconds and the camera to be shown Times from 1 to 180 seconds are determined with 1 second step from 181 to 400 seconds in 5 second steps from 401 to 600 seconds in 10 second steps Inserting a time of 0 seconds or pressing Dec while changing a value erases the step Allocating cyclic sequences After the cyclic sequences have been defined the sequence to be shown must be assigned to each monitor Press 1 and 2 if Night Sequences are provided to change the desired sequence The first cameras in the sequence are shown Menu 4 2 Page 21 of 33 MNYASM328S_0648 Auto return time Auto return time is the time between manual selection of a camera by the operator and automatic return to the cyclic sequence between 1 and 60 minutes If set to 0 it is disabled Alarms Are alarms used Matrix alarms can be activated in 2 ways Menu 5 e Contact Alarms the alarm is activated when the respective contact on the rear connector is OPEN if the alarm is defined aa NORMALLY CLOSED or CLOSED if the alarm is defined as NORMALLY OPEN e Aux Command Alarms the alarm is activated upon receving a proper comm
4. keyboard connected to the matrix On Screen Menu Matrix Setup Only Single or Master matrixes have to be setup Slave matrixes are not configured Setup by On Screen Menu Setup by On Screen Menu interrupts matrix operation any alarms arriving during setup will not be acknowledged and puts the connected keyboards into a special mode When exiting from setup the matrix temporarily resets for a few seconds to accept the new settings The keys used for On Screen Menu setup are shown on the screen as necessary To enter a submenu press the corresponding number to exit press the Seq key Sometimes it will be possible to scroll through a series of lines with Inc Dec and request a change to the line indicated by the cursor by pressing the Enter key There are different ways of changing the parameters depending on the item to be modified e by inserting a numeric value which is then to be confirmed by Enter an inserted value that has not been confirmed can be erased with Clear it is often possible to cancel a whole setup line by pressing Dec when inserting a numerical value e by pressing a number till the desired item is selected if the choice is between a few options every time the key is pressed the next value is suggested Page 15 of 33 MNYASM328S_0648 Entering Program Mode DCT Keyboard To be completed Any information to describe program mode by VSP Setup Parameters Video system The matrix is designed
5. 3 MNYASM328S_0648 Don t connect any other device on the Aux A line To comply with the standard the RS485 communication lines must be terminated at the ends to prevent signal reflection On the Aux A auxiliary communication line the load can be inserted jumper AUX_A in LOAD position or excluded jumper AUX _A in NO position Please insert the load only for the matrixes at the end of the line To connect the Matrixes please use this cable MASTER 0000000000000000 0000000000000000 0000000000000000 0000000000000000 SLAVE 2 0000000000000000 0000000000000000 OP Prrrno 00000000 AA Master Matrix Slave 1 Slave 2 Aux A AuxA Aux A RS485A white white white RS485B yellow yellow yellow Personal Computer and Serial Printer Cable MAX 1200 m Connect the personal computer or serial printer using a standard complete male female 9 pin serial cable serial extension Page 10 of 33 MNYASM328S_0648 BNC for the Alarm Reset The external alarm reset trigger is supplied via BNC TRIGGER GND The minimum length of the reset alarms impulse is 30 ms Relay and alarm connectors The matrix provides 2 connectors ALARM A and ALARM B respectively for alarm contacts and relays On a Slave Matrix these connectors are disabled Page 11 of 33 Pin DB25A DB25B Pin DB25A DB25 B 1 Alarm 1 Alarm 17 14 Al
6. 32 communication to PC max 15m RS485 communication to max 1200m keyboards Page 32 of 33 MNYASM328S_0648 RS485 communication to Aux devices max 1200m Mux and telemetry receivers Relay contacts 50 V AC DC 0 5 A max Epoxypoliester powder painted metal enclosure Net weight excluding p s 3 2 kg 180 L x 430 W x 94 H mm rack 19 2HE Working temperature 0 45 C EN55022 Class A EN50130 4 EN60065 Compliance to FCC Part 15 Class A Page 33 of 33 MNYASM328S_0648
7. Cyclic sequences 1 Defining and modifying the cyclic sequences 2 Allocating cyclic sequences 1 Auto return time 10 Alarms Contact Alarms Aux Command Alarms ID text Reset modes Enabling the alarm contact Effects on the monitors Action on receivers Action on relays Buzzer 11 Image Masking 1 Changing the masking 1 Definition of a mask 4 Composite systems 1 1 Matrix and 1 Slave 2 1 Matrix and 2 Slaves 5 Event log 1 List of event messages 2 Baud rate and data format 4 Technical specifications vonsurwun The manufacturer declines all responsibility for any damage caused by an improper use of the appliances mentioned in this manual furthermore the manufacturer reserves the right to modify its contents without any prior notice The documentation contained in this manual has been collected with great care the manufacturer however cannot take any liability for its use The same thing can be said for any person or company involved in the creation and production of this manual Page 2 of 33 MNYASM328S_0648 Introduction Typographical conventions This instruction manual makes use of different graphics symbols A Hazard of electric shock unplug the power supply before proceeding with any operation unless specified otherwise i gt Important please read the procedure or information given and when ieo perform the operations as instructed Fai
8. amera selected by the Master Operator may be replaced by a substitute camera This is useful for preventing the ill intentioned from watching a monitor made public as a deterrent and getting to know the intentions of the security personnel If exclusion is ON each camera selected by the Master Operator will be substituted in all the cyclic sequences of the other monitors not in alarm status It is the operator s task to re position the pan amp tilt as appropriate before restoring normal operation Page 19 of 33 MNYASM328S_0648 Auto return time from 1 to 60 minutes is used to return the system to normal mode without camera exclusion after a fixed time following selection by the Master Operator If set to 0 it is disabled and the system does not return to normal mode In the example the Control Monitor sho a cyclic sequence o inputs 1 2 3 and 4 4 2 3 4 2 The Public Monitor shows inputs 1 and Camera 1 frames th zone including the Public Monitor During active contre of video input 1 we recommend removil the input itself fron the cyclic sequence the public monitor In this case it has be replaced by input 5 called substitute camera The camera is excluded only if the Public Monitors are in automatic cyclic sequence The Control Monitor is always number The video input is excluded when a camera is selected on the master monitor During exclusion the Control Mon
9. an be configured to position telemetry devices domes on alarm using SSP communication protocol Please set the dome baudrate at the value set for keyboards communication cfr Dip switch configuration Using an RJ jack shunt box connect the dome to the proper RS485A and RS485B lines 0000000000000000 0000000000000000 000000000 MAX 1200 m Single Matrix Poles Keyboards Mater Matrix RS485A white blue line A RS485B Page 8 of 33 MNYASM328S_0648 DVR and direct coax Telemetry control Keyboards can control MUX DVRs and Telemetry devices domes using SSP communication protocol Optionally Telemetry devices can be controlled by COAX through the MUX DVRs when this function is provided by the MUX DVR device Please set the baudrates at the value set for keyboards communication cfr Dip switch configuration Using RJ jack shunt boxes connect the objects to the proper RS485A and RS485B lines 9 8 PA Aresa Jess COAX COAX COAX RELAY2 MATRIX 4 oo KEYBOARD 1 CONNECTOR YZ CONNECTOR Single Matrix DVRs Poles Keyboards Matrix Master MUXes Domes RS485A white blue red line A RS485B yellow black green line B Aux Line The matrix is provided with 2 Aux lines e Aux A is used to control optional auxiliary Slave matrixes e Aux B is reserved for future use In the case of Single Matrix configuration Aux A is not used Page 9 of 3
10. and from keyboard Functionally these 2 types of alarm behave in the same way and each alarm can be either CONTACT or AUX COMMAND type but not both On alarm a number of automatic operations can be performed e Switching of chosen cameras or sequences on some monitors Menu 5 5 e Telemetry control to put connected domes receivers on Home Position up to 4 distinct positionings are available Menu 5 6 e Close of relays Menu 5 7 e Buzzer activation Contact Alarms The matrix is supplied with 32 alarm contacts which are defined as normally closed or normally open Only alarm contacts on Single and Master Matrixes are available contacts on Slave matrixes are not enabled Alarm contacts that are not used should be set up as NOT USED to prevent false signals in the event of disturbance An alarm is acknowledged if the corresponding actuating signal is at least 30ms long Aux Command Alarms The use of Aux Command Alarms allows flexible management of periferal units Page 22 of 33 MNYASM328S_0648 such as VCRs connected to the system and multiple actions by pressing a single key AUX RESET commands are provided to reset the alarm condition by keyboard AUX COMMAND ALARMS can only be reset by keyboard Actions on telemetry receivers are also available when the dome receiver is controlled through a DVR by Coax connection CONNECTOR Re EN _ LZ CONNECTOR In this example it is assumed that e
11. arm 14 Alarm 30 2 Alarm 2 Alarm 18 15 Alarm 15 Alarm 31 3 Alarm 3 Alarm 19 16 Alarm 16 Alarm 32 4 Alarm 4 Alarm 20 17 Common al Common al 5 Alarm 5 Alarm 21 18 Relay 1A Relay 5A 6 Alarm 6 Alarm 22 19 Relay 1B Relay 5B 7 Alarm 7 Alarm 23 20 Relay 2A Relay 6A 8 Alarm 8 Alarm 24 21 Relay 2B Relay 6B 9 Alarm9 Alarm 25 22 Relay 3A Relay 7A 10 Alarm 10 Alarm 26 23 Relay 3B Relay 7B 11 Alarm 11 Alarm 27 24 Relay 4A Relay 8A 12 Alarm 12 Alarm 28 25 Relay 4B Relay 8B 13 Alarm 13 Alarm 29 MNYASM328S_0648 Electrical specifications of the alarms MN Warning Do not power the alarm contacts The sensors or the alarm conta centre must supply a dry contact Electrical specifications for the relays Switching power 10W max Switching voltage 50 VAC DC max Switching current 0 SA max Jumpers and DIP Opening the matrix Inside the matrix there are two jumpers for inserting the RS485 load AUX_A behind the Aux connectors AUX B is provided only for future use one DIP switch SW1 near the backup battery in the centre of the board and a backup battery ARA supers f BATTERY DIP SWITCH Warning The operations described below are carried out with the matrix cover removed Take great care to prevent the risk of electric shock Dip Switch Configuration DEN To prevent faulty operation of the system do not make DIP switch settin
12. devices changes continuously and cannot be effectively masked Menu 6 Masking may only be defined for video inputs present at the time of setup in order to be able to modify masking the video signals should already be connected to the matrix Changing the masking IfEnabled is OFF all Masks are not visible even if previously defined Definition of a mask Each camera is provided of a unique mask definition Menu 6 2 Select the camera to be masked pressing Inc Dec To erase completely a mask on the camera press 0 O zero twice Move the cursor with keys Up Down Left Right and toggle active cell visibility by pressing Enter Press Seq when mask definition is complete Composite systems The matrix can be cascaded to connect more than 32 video inputs e 2 matrixes 1 Master 1 Slave up to 48 inputs Page 26 of 33 MNYASM328S_0648 e 3 matrixes 1 Master 2 Slaves up to 80 inputs A Slave matrix is just an extension card it provide neither relays nor alarm contacts Keyboard can only be connected to the Master matrix 1 Matrix and 1 Slave VIDEO INPUTS 17 48 VIDEO INPUTS 1 16 KEYBOARD 1 lt CONNECTOR RN de aise VIDEO Gs Video inputs e Master matrix from 1 to 16 e Slave matrix from 17 to 48 The Slave matrix must be set as Slave no 1 Connection cable is described in Aux Line Slave s outputs are connected to Master s inputs according to this table Slave output Master input
13. e corresponding number then press 0 tolgnore the alarm 1 to request a cyclic sequence 2 to request a fixed camera If a sequence or a camera is requested it is then necessary to indicate the desired number and then confirm it with Enter A sequence camera number equal to 0 or pressing Dec during insertion will cancel the action Action on receivers If the telemetry receivers are controlled via the matrix it is possible to reposition up to 4 receivers when an alarm event is identified Menu 5 6 The receiver number is always between 1 and 127 Setting the number 0 or pressing Dec during insertion will cancel the action The action on alarm can be selected e scan on predefined preset position e autopan e tour Page 25 of 33 MNYASM328S_0648 e sequence patrol Action on relays If a relay is controlled by an alarm acknowledgement of the alarm is able to close it automatically When more than one alarm controls the same relay acknowledgement of any one of these alarms will cause the relay to close When all alarms controlling the relay cease the relay will open Menu 5 7 Buzzer It is possible to enable a warning buzzer on the matrix each keyboard is set up individually for another warning buzzer in the event of an alarm Image Masking Image Masking is a system to hide part of the image when this comes from fixed cameras Do not mask signals from pan amp tilt cameras domes or VCR outputs the view provided by these
14. e the marking labels to make sure the supplied material corresponds with the required specifications Do not for any reason make changes or connections unless indicated by this manual using unsuitable equipment may constitute a serious safety hazard for people and for the system Switching on and off Before powering the appliance e Examine the marking labels to make sure the supplied material corresponds with the required specifications e Make sure the matrix and other components in the system are closed up properly so that the direct contact with operating devices is impossible except for the installation procedure otherwise required in this case proceed with great care following the instructions given in this manual e the matrix and the other parts of the system should rest on a large solid base e The power supply and connecting cables should not hamper the installer technician and operators when carrying out normal operations e Make sure the power outlet and extension cables if any are sufficient for the power load required by the system If in doubt always consider the system on Switching on A Plug the power supply into the power outlet and connect the corresponding jack to the matrix connector labelled 12VDC Turn the front switch to the ON 1 position The LED on the front of the matrix should light up Switching off Turn the front switch to the OFF O position Page 5 of 33 MNYASM328S_0648 Connector
15. et from among the definitions Menu 5 3 For Contact Alarms four reset modes are available e Continuous type reset when the alarm signal ceases instructed by a control centre for example the alarm event is silenced e Keyboard reset keyboards able to reset the alarm are indicated e External reset the alarm is silenced by an external reset trigger e Time reset the alarm is automatically silenced following a specified time after acknowledgement This time can be selected from among 2 5 10 20 30 60 seconds 2 5 10 15 30 60 minutes 3 6 12 hours Notes Do not use the continuous type reset if the alarm signal is of the pulsed type Page 24 of 33 MNYASM328S_0648 supplied by a sensor attached to a door for example The external reset trigger should be enabled to be able to reset the alarms by external reset For Aux Command Alarms only a keyboard Aux Reset Command is available Enabling the alarm contact Acknowledgement of alarm events can be limited to specific periods day or night period always or never the latter is useful if the alarm is to be temporarily disabled without losing the already completed setting such as when testing a system Menu 5 4 Effects on the monitors When an alarm is acknowledged each video output may react differently Menu 5 5 e the alarm may be ignored e a fixed camera may be shown e a pre defined cyclic sequence may be shown To change the effect on a monitor press th
16. for use in PAL NTSC systems with interlaced and non interlaced video outputs Menu 2 1 If there is an obvious shift in the texts caused by monitors for which it is impossible to adjust V HOLD it is possible to centre the screen Menu 2 1 3 Removing Texts and Masks A special menu to remove Camera ID Texts Alarm Texts Date Time Image Masks reads on monitor is provided Menu 2 1 4 This is useful during installation the installer can read on screen all information to check if the system is properly set sequences alarms etc and can later remove this information to avoid it being mixed to the one provided by domes DVRs MU Xes Simplify Menu To simplify the setting it is possible to remove Night Sequences and Daylight Saving Time when these features are not used Menu 2 2 Day and Night Periods Should matrix operation be differentiated between day and night Sometimes matrix operation differs during the day the period when the building under surveillance is open to public staff and at night when the building is closed the staff is not present and the surveillance system is normally used by security personnel Holidays are considered Night Periods Many matrix functions alarm acknowledgement enabled keyboards automatic sequences etc depend on the time period Should differentiated operation be unnecessary the menus can be simplified to make system setup easier External Contacts This menu enables disables the Exter
17. gs that are not included in the following tables Page 12 of 33 MNYASM328S_0648 System configuration and baud rate Dip switches set the system configuration and communication baudrate Communications uses SSP protocol ref doc SCTI I001E Security Serial Protocol SSP ver 1 14 03 08 19 All the devices connected to the line must be set accordingly Dips Dip3 Dip2 Dip1 System Slaves Baudrate 19200 SINGLE 9600 off N A MATRIX 4800 2400 19200 9600 off 1 Slave 4800 MASTER an MATRIX 19200 9600 ON 2 Slaves 4800 2400 Configured as Slave number N A 1 off SLAVE MATRIX Configured as Slave number N A 2 Slave matrixes are used only for video input extension They provide neither alarms information nor video texts Slave matrixes are not set up the whole configuration is set up in the Master matrix Page 13 of 33 MNYASM328S_0648 Restoring the factory default settings It is possible to restore the factory default settings for the matrix using the Dip Switch All previous parameter settings will be lost 1 Switch off the matrix 2 Set Dip 6 to ON 3 Switch on the matrix and wait until the presentation screen disappears 4 Set Dip 6 to OFF Updating the firmware The matrix firmware program can be updated when necessary When the firmware is updated the matrix setup is not erased After updating however we advise checking all the previous parameter settings are still cor
18. itor reads a warning message This message is overrided by an eventual alarm message To end camera exclusion press Seq to request the automatic sequence on the Control Monitor Cameras ID Texts The matrix allows up to 80 cameras to be connected Each camera has an ID text of max 28 char When possible part of this text is shown in the various menus when defining the cyclic sequences for example to make setup control easier Menu 3 Page 20 of 33 MNYASM328S_0648 Move the cursor to the desidered camera by means of Inc and Dec It is possible to select quickly a camera text by pressing the number on the keyboard 1 e 2 8 to select camera 28 Enter is used to start modification of the ID text indicated by the cursor The text is inserted in the same way as for a cell phone pressing a numeric key quickly several times will run through the characters associated with the key a pause is used to pass to the next character Enter inserts a space and Clear erases the last character Inc and Dec change the character set Cyclic sequences Cyclic sequences are series of cameras that are shown consecutively according to a predefined order Menu 4 1 Each sequence consists of max 32 cameras each of which can be shown for a time ranging from to 600 seconds The cameras may be repeated within a sequence in any order Defining and modifying the cyclic sequences The definition screen shows the list of 32 available cyclic sequences
19. lure to carry out the procedure correctly may cause faulty operation of the system or even damage it ES Notes we recommend reading the notes to fully understand the system operations Safety rules amp The SM328S video matrix complies with current legislation and standards regarding electrical safety electromagnetic compatibility and general requirements in force at the time of publication of this manual Nevertheless in order to ensure the users safety installer technician and operator we hereby specify the following advice for working as safely as possible e Only authorised skilled technical personnel should be allowed to install the appliance and the whole system of which it forms part e Never open the appliance unless required by specific procedures described in this manual e Connect the appliances to a power supply that corresponds with their respective identification labels e For technical services refer only and exclusively to authorised technical personnel e Do not extract the plug by pulling on the cable e Before moving or carrying out technical work on the appliance disconnect the power supply jack the appliance is to be considered OFF only when the power supply jack is disconnected and the connection cables to other devices have been removed Page 3 of 33 MNYASM328S_0648 e Do not use extension cables with signs of wear or ageing since they could expose the user to serious safety hazards e Do n
20. nal Alarm Reset Contact Menu 2 3 Page 16 of 33 MNYASM328S_0648 Date The matrix is able to display the date and time and use these parameters to vary operation depending on the period Menu 2 5 For the Date it is possible to make the following settings e the current date e the format International year month day European day month year American month day year e position and visibility e closed periods during the week extra holidays and periods when the building 1s closed Weekdays Available only if Night sequences are used For each day of the week Monday Tuesday etc 1t 1s possible to define a maximum of four time periods during which the building is considered open Day Periods At all times outside these 4 periods the building is considered closed Night Periods Menu 2 5 7 1 It is possible to copy the parameter settings for a particular day using the 0 zero key so as to simplify insertion when the periods are the same from Monday to Friday for example To cancel a line press Dec when inserting the numeric value Single day Holidays Available only if Night sequences are used Single day holidays are defined as days that are not included as normal non working days such as Sundays Menu 2 5 7 2 For each day key in the numerical values as requested If the value inserted is not valid the previous setting will not be changed To cancel a line press Dec when inserting a numerical value It is pos
21. on keyboard the Aux key sends to the matrix the message Aux 7 to activate Alarm no 7 e on the matrix Alarm no 7 is defined as AUX COMMAND and performs these actions o it closes relay 2 o it switches a camera related to a DVR on a monitor o it moves dome no 17 to preset no 1 home o it enables the matrix buzzer e on the DVR dome no 17 is connected through coax cable it is also possible to connect the domes even on the keyboard line This is the sequence of actions Page 23 of 33 MNYASM328S_0648 e The operator 1 press the Aux key and a Aux 7 command is sent to the matrix e The matrix 2 recognizes the command and set Alarm no 7 off e Relay no 2 1s closed e The operator s monitor 6 shows an alarm related camera e A message to move dome 17 to home is sent by the matrix e Alarm buzzer is activated e DVR 4 receives the command sent to the dome and retransmit it through coax e Dome 17 5 moves to home position e After closing the relay VCR 3 starts recording To reset the Alarm a command Aux 7 must be provided on the keyboard ID text The Alarm ID Text can have a max 28 characters and the procedure to define it is the same for ID texts for the cameras Menu 5 2 Reset modes Each alarm can be silenced in various ways and the reset mode setting for one alarm will not influence the other alarms If more than one reset mode is defined for the same alarm this alarm will be silenced by recognition of the first res
22. ossible for them to control the matrix Each keyboard can be set as e not connected when it is necessary to disable the keyboard during tests Page 18 of 33 MNYASM328S_0648 e connected o always enabled o never enabled temporarily disabled during system tests o enabled during Day periods when Night sequences are used o enabled during Night periods when Night sequences are used If a keyboard is not enabled any command send to the matrix will be ignored Control Monitor Monitor 1 can be used as Control Monitor when this is necessary for specific surveillance features Menu 2 8 Messages on the Control Monitor Do you want to receive warning messages on Monitor 1 Every significant event occurring to the matrix alarm events and reset video signal loss period change etc can be shown on the Control Monitor On pending events a blinking lt E gt is read on the screen bottom right Security personnel may view the event log by pressing Enter and then take appropriate action when necessary The Master Operator can optionally delete the complete log or a single line The log can have a maximum of 100 lines when 100 lines are reached the least recent messages are overwritten Excluding video inputs Is the matrix used in a shopping mall Is the public able to see some of the monitors When the matrix is used in particular public places such as shopping malls where one of the monitors is accessible to the public each c
23. ot allow any liquid to wet the appliance and do not touch it with wet hands when in operation e Do not leave the appliance exposed to adverse weather conditions e Do not use the appliance in the presence of inflammable substances e Make sure the appliance is always placed on a sufficiently solid broad base Tampering with the appliance will invalidate the guarantee Keep this manual carefully for future consultation gt Warning this is a Class A product In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures System installation Preliminary operations Opening the package When the product is delivered make sure the package is intact and has no obvious signs of dropping scrapes or scratches If the package is damaged or if there is something missing from the following list contact the supplier immediately Material supplied with the matrix should be as follows e programmable SM328S video matrix e user s manual e wide range power supply IN 100 240V AC 50 60Hz OUT 12VDC including cables 2 DB25 connectors complete with shell 1 serial 9 pin cable Checking the markings The base of the matrix has a label that complies with CE markings containing Page 4 of 33 MNYASM328S_0648 e Product identification code e Power supply voltage Volts e Frequency Hz e Maximum consumption Watts Before proceeding with the installation examin
24. rect and if not we advise proceeding to reset the matrix and then re configure all the parameters 1 Switch off the matrix 2 Connect the Personal Computer using the serial cable 3 Set dips 7 and 8 to ON 4 Run the update program 5 When updating is finished close the program then switch off the matrix 6 Set dips 7 and 8 to OFF 7 Switch on the matrix and make sure it is set up correctly Maintenance Inside the matrix there is a battery to store the date and time when the matrix is switched off If it has to be replaced open the cover as described in section Opening the matrix with the matrix switched off Replace with a CR1225 battery or equivalent DL1225 ECR1225 BR1225 DL1225B BR1225 1W CR1225 1W KCR1225 LM1225 5020LC L30 Page 14 of 33 MNYASM328S_0648 The positive terminal should face upwards Battery change is not necessary for Slave matrixes Setup Notes regarding the menu system Setting up the matrix 1s a rather complex operation we advise proceeding a step at a time in the order suggested by the menus The choices made in one menu will often affect subsequent menus which may or may not show the setup parameters The menus can be further simplified by appropriate settings to the items in the menu for System setup Simplify menu all functions that are not used will be automatically removed from subsequent menus thus considerably reducing the possibility of errors Setup is carried out using a
25. relay number i OpenRelayX 1 8 Time event relay No X BueontaceKx XX contact Time event alarm number 1 32 contact XX DisContactXX Pr Contact Time event alarm number 1 32 DateChange Start date modification DateSet End of date modification TimeChange Start time modification TimeSet End time modification 1 The time at which the matrix was switched off is shown the next time it is switched on 2 After the message for the start of the day night period there is a description of the status of the keyboards relays and alarm contacts Message Parameters Meaning Page 31 of 33 MNYASM328S_0648 X1 X8 Status of the keyboards KeyboardsX1 X8 ad ae keyboard enabled y keyboard disabled Status of the relays relay controlled by alarm X1 X8 relay enabled relay disabled status 1 relay controlled by time events enabled 0 relay disabled RelaysX1 xX8 Status of the alarm contacts X1 X32 contact status ContactsXx1 X32 contact enabled contact disabled Baud rate and data format The baud rate is the one set by the Dip Switch for communications with the keyboards Format is 8 bit No parity 1 stop bit Technical specifications Power supply 100 240 V 47 63 Hz Consumption max 24 W 32 inputs 75 Ohm 1 Vpp PAL NTSC Video 8 outputs 75 Ohm 1 Vpp PAL NTSC gt 6 Mhz Lower cut off frequency 3dB na Signal noise ratio S N gt 47 dB 5 5MHz RS2
26. s a corresponding message in code that is sent to the RS232 channel The message is preceded by an indication of the date and time and is followed by a checksum character List of event messages PowerOn Matrix switched on Page 29 of 33 MNYASM328S_0648 Poweroff Matrix switched off PeriodDay Start of Day Period PeriodNight Start of Closed Period Start of summer time DST l End of summer time Time 1 TST Setup Start of matrix setup EndSetup End of matrix setup AlarmXX XX alarm number Acknowledgement of 1 32 alarm XX csi X keyboard Reset alarms from number 1 8 keyboard No XX aux command An alarm activation is Aux XX from keyboard requested from keyboard XX aux reset i An alarm reset is Aux XX command from requested from keyboard keyboard aan XX alarm number Alarm active but 1 32 disabled AlarmXXIdleoff en number Alarm idle but disabled AlarmExtReset External alarm reset AlarmXXTimeReset eco number Time alarm No XX AlarmXXAutoReset XX alarm number Continuous 1 32 f XX camera Video XX Video loss camera No XX number 1 32 Page 30 of 33 MNYASM328S_0648 Video XX XX camera Signal return video number 1 32 No XX CfgReset Restore settings MicroReset Re run program EnKeybX X keyboard Time event keyboard number 1 8 No X DisKeybX X keyboard Time event number 1 8 X relay number E CloseRelayX 1 8 Time event relay No X X
27. s and cables Video cables Use an RG 59 coaxial cable or equivalent Over large distances we advise using a video transmission system via twisted pair Keyboard lines Keyboards can only be connected on a single line to a Single or Master matrix Keyboards cannot be connected to Slave matrixes The matrix has four RS485 lines for the keyboards connection but only either number 1 or number 2 can be used not at the same time e Line 1 is not loaded un terminated use this line when the matrix is not at the end of a RS485 line in a real system this is the most frequent case e Line 2 is loaded terminated use this line when the matrix is at the end ofa RS485 line 1 e during tests with a direct connection between keyboard and single matrix e Lines 3 and 4 are reserved for future use and cannot be used It is possible to connect a keyboard directly to the matrix using a phone cable 1 5m or using a long distance cable up to 1200m use RJ jack shunt boxes and a non shielded twisted pair with minimum diameter 0 6 mm sect 0 22 mm AWG 24 Page 6 of 33 MNYASM328S_0648 Keyboard Tx 0000000000000000 0000000000000000 0 OPPERATOOOOOOOVO 0000000000000000 0000000000000000 gt e 0 OND KEYBOARD2 gt Matrix Rx RS485A white RS485A blue RS485B yellow RS485B black Page 7 0f 33 AAO OO ODOO000 MAX 1200 m MNYASM328S_0648 Direct Telemetry control The matrix c
28. sible to define a maximum of 16 single day holidays over the year Holidays Periods Available only if Night sequences are used Page 17 of 33 MNYASM328S_0648 These are periods when the building is closed for holidays and are defined by inclusive initial and final dates Menu 2 5 7 3 It is possible to define a maximum of 8 holidays periods over the year Time For Time it is possible to make the following settings Menu 2 6 e current time e format International 24 hour English 12 hour AM PM e position and visibility e parameters for automatic management of Daylight Saving Time Daylight Saving Time Daylight Saving Time can be set in some ways Menu 2 6 7 e Automatic on predefined Zones Europe Russia America Australia e Automatic on predefined time spans from Last Sunday in March to the Last Sunday in October e Manual defining a begin end time span gt Warning The Date Time type parameters are valid for only one year and Fona then be reset to the correct values as and when necessary Enabling the keyboards Are some of the keyboards enabled only during certain day periods Each keyboard is identified by a number from 0 to 4 which is set at the keyboard level independently of the matrix connector to which the keyboard is connected Menu 2 7 1 i Warning The number should not be repeated within the group of keyboards aned to a system the presence of keyboards with the same ID number will make it imp
Download Pdf Manuals
Related Search