Hydraulic Truck Jack Operating Instructions & Parts
Contents
1. 0008 Internal Piston Air 1 Motor A300 90009 K02 Hydraulic Unit A070 00003 000 Wheel Axle Figure 2 Replacement Parts amp Illustration for Model 23301C 6 ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO ONE YEAR OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS2. Operating Instructions Parts Manual Model 23301C Capacity 30 Ton U S Patent Nos 5 341 723 5 946 912 A This is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death e Leer comprender y seguir las instrucci nes antes To avoid crushing and related injuries de utilizar el aparato e NEVER work on under or around El manual de instrucci nes y la informaci n de a load supported only by a hydraulic seguridad deben estar comunicado en lengua del jack operador antes del uso e ALWAYS use adequately rated jack e No seguir estas indicaci nes puede causar da os stands personales o materiales SFA Companies http www omegalift com Read this manual and follow all the Safety Rules and Operating Instructions before using this product Made in China 23301C MO 10 08 SAFETY and GENERAL INFORMATION Save these instructions For your safety read understand and follow the information provided with and on this jack before using The owner and operator of this equipment shall have an understanding of this jack and safe operating procedures before attempting to use The owner and operator shall be aware that use and repair of this product may require special skills and knowledge Instructions and safety information shall be conveyed in the operator s native language before use of t
3. Simply release your grip on the lift control valve to end lift event 5 Transfer the load immediately to appropriately rated jack stands Only attachments and or adapters supplied by the manufacturer shall be used Lift only on area of the vehicle as specified by the vehicle manufacturer NEVER use hydraulic jack as a stand alone device ALWAYS transfer the lifted load IMMEDIATELY to a pair of appropriately rated jack stands Use one pair of jack stands per vehicle Rated capacity is per pair only Do not exceed rated capacity Lowering Be sure all tools and personnel are clear before lowering load Slowly open the release valve The more you turn the handle knob counter clockwise the faster the load will come down Maintain control of the rate of speed at which the load lowers at all times 1 Raise load high enough to clear the jack stands 2 Remove jack stands carefully always used in pairs 3 Slowly turn handle knob counter clockwise but no more than 1 full turn If the load fails to lower a Use another jack to raise the vehicle high enough to reinstall jack stands b Remove the malfunctioning jack and then the jack stands c Use the functioning jack to lower the vehicle 4 After removing jack from under the vehicle fully retract the jack to reduce ram exposure to rust and contamination 4 MAINTENANCE Important Use only good grade hydraulic jack oil Avoid mixing different types of fluid and NEVER use brake fluid turbine
4. THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitations on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies 10939 N Pomona Ave Kansas City MO 64153 888 332 6419 OMEGA sales omegalift com SFA Companies 10939 N Pomona Ave Kansas City MO 64153 6 OMEGA 888 332 6419 sales omegalift com
5. e bolt on handle sleeve to prevent accidental removal of handle while in use Before Use 1 Verify that the product and application are compatible if in doubt call Omega Technical Service 888 332 6419 2 Before using this product read the operator s manual completely and familiarize yourself thoroughly with the product its components and recognize the hazards associated with its use 3 To familiarize yourself with basic operation locate and turn the release valve handle knob a Clockwise until firm resistance is felt to further turning This is the CLOSED release valve position used to raise the load b Counter clockwise but no more than 1 full turn from the closed position This is the OPEN release valve position used to lower the load The more you turn the release valve counter clockwise the faster the load descends 4 With ram fully lowered remove the oil filler plug Check oil level Proper oil level should be just below the rim of the opening Reinstall the oil filler plug 5 Pour a teaspoon of good quality air tool lubricant into the air supply inlet of the lift control valve Connect to air supply then squeeze the lift control valve for 3 seconds to evenly distribute lubricant Note These models are equipped with the popular 1 4 NPT air coupler When installing a different air coupler of your choice ensure that thread tape or compound is used when servicing connections To ensure dependable trouble free operat
6. his jack is authorized If any doubt exists as to the safe and proper use of this jack remove from service immediately Inspect before each use Do not use if broken bent cracked or damaged parts are noted Any jack that appears damaged in any way or operates abnormally shall be removed from service immediately If the jack has been or suspected to have been subjected to a shock load a load dropped suddenly unexpectedly upon it immediately discontinue use until jack has been checked by a factory authorized service center contact distributor or manufacturer for list of authorized service centers It is recommended that an annual inspection be done by qualified personnel Labels and Operator s Manuals are available from manufacturer PRODUCT DESCRIPTION This category of Hydraulic Truck Jack is designed to lift but not support rated capacity partial vehicle loads consisting of one end of a vehicle Immediately after lifting loads must be supported by a pair of appropriately rated jack stands NEVER use a hydraulic jack as a stand alone device After lifting immediately support the lifted vehicle with a pair of appropriately rated jack stands NEVER place any portion of your body beneath the vehicle when lifting OR lowering PREPARATION Assembly see Replacement Parts page 6 for reference to parts location amp assembly sequence Assemble align and insert the handle assembly 8 handle position bar into the handle sleeve then tighten th
7. ion an inline air dryer and oiler is recommended 6 Ensure that jack rolls freely Raise and lower the unloaded ram throughout the lifting range before putting into service to ensure the jack operates smoothly Replace worn or damaged parts and assemblies with Omega authorized replacement parts only Bleeding Venting Trapped Air With the release valve in the OPEN position 3b and with ram fully lowered locate and remove the oil filler plug This will help release any pressurized air which may be trapped within the reservoir Reinstall the oil filler plug SPECIFICATIONS Capacity Jack Size L x W Min Height Max Height Hyd Lift Handle Position Release Handle Knob release valve Air Supply Inlet 1 4NPT Lift Control Valve Handle Handle Sleeve Oil Filler Plug not shown Carrying Handle Figure 1 Model 23301C Nomenclature Study understand and follow all printed materials provided with on this product before use Do not exceed rated capacity This is a lifting device only Immediately after lifting support the load with a pair of appropriately rated jack stands only by hydraulic jack Use only on hard level surface e Always use adequately rated jack stands Lift only on areas of the vehicle as specified by Chock each unlifted tire in both directions the vehicle manufacturer Do not use this device to lift level lower support nor Never wire clamp or otherwise disab
8. le the lift move a house mobile home travel trailer camper or control valve to function by other than operator s any building structure hand Be alert and sober when using this product Do not No alterations shall be made to this product operate under the influence of drugs or alcohol Failure to heed these markings may result in personal injury and or property damage To avoid crushing and related injuries e Never work on under or around a load supported The wheels provided with this jack are for positioning the jack under a load ONLY The wheels are not load wheels Do not try to dolly or move the vehicle while the jack OPERATION see Fig 1 Lifting Note Jack is equipped with a handle position lock To adjust the handle release lock device by pulling the lever up lever is spring loaded and will lock into desired position Ensure lever locking mechanism is fully engaged before using jack 1 Connect adequate air source to the air supply inlet 2 Follow the vehicle manufacturer s recommended guidelines for lifting Engage the emergency brake and chock each unlifted wheel in both directions to prevent inadvertent vehicle movement 3 Close the release valve by turning the handle knob clockwise until firm resistance is felt 4 Center jack saddle under lift point then squeeze the lift control valve until saddle contacts the lift point To lift continue squeezing the lift control valve until load reaches desired height
9. oil transmission fluid motor oil or glycerin Improper fluid can cause premature failure of the jack and the potential for sudden and immediate loss of load We recommend Mobil DTE 13M or equivalent Adding Changing Oil For best performance and longest life replace the complete fluid supply at least once per year 1 With saddle fully lowered remove cover plate then oil filler plug 2 Lay jack on its side and drain fluid into a suitable container Note Dispose of hydraulic fluid in accordance with local regulations 3 Set jack in its upright level position 4 Fill with oil Proper oil level is just below the rim of the opening Reinstall the oil filler plug Lubrication A periodic coating of light lubricating oil to pivot points axles and hinges will help to prevent rust and assure that wheels move freely and the pump functions smoothly To help ensure trouble free operation an inline air dryer and oiler is recommended Cleaning Periodically check the ram for signs of rust or corrosion Clean as needed and wipe with an oily cloth Note Never use sandpaper or abrasive material on ram surfaces Paint contains lead DO NOT sand or grind painted surface Storage When not in use store the jack with saddle fully lowered REPLACEMENT PARTS see page 6 Not all components of the jack are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts please give
10. the Model number part number and parts description Call or write for current pricing SFA Companies 10939 N Pomona Ave Kansas City MO 64153 U S A E Mail salesQ omegalift com Tel 888 332 6419 Fax 816 891 6599 Omega Website http www omegalift com TROUBLESHOOTING Symptom Possible Causes Corrective Action Jack will not lift load e Release valve not tightly closed e Ensure release valve tightly closed e Load is too heavy e Consider higher capacity jack e Air supply inadequate e Ensure adequate air supply Jack will lift but not maintain e Release valve not tightly closed e Ensure release valve tightly closed pressure e Hydraulic unit malfunction e Discontinue use contact Omega technical service Jack will not lower after unloading Reservoir overfilled e Drain fluid to proper level e Linkages binding e Clean and lubricate moving parts Poor lift performance e Fluid level low e Ensure proper fluid level e Air trapped in system e With ram fully retracted remove oil filler plug to let pressurized air escape Reinstall oil filler plug Will not lift to full extension e Fluid level low e Ensure proper fluid level 6 s303 00010 000 washer Lock 5 e A300 00005 000 Gover Plate 1 ls 5110 06010 00 Screw 5 19 A20060 0016 Air Coupler Male 1 1 4 NPT 20 A070 30000 000 Release Valve 1 Cable A300 90009 K01 Repair Kit includes 5 22 26 amp a q 33 A27010
Download Pdf Manuals
Related Search