Engine Transverse Bar w/Support Arm Operating Instructions
Contents
1. as some length adjustment may be required c Before placing the Engine Transverse Bar over the engine compartment install the two threaded hooks 3 provided Insert one hook to the tube welded on boom 1 and secure with barrel hex nut 7 Thread the hex nut 7 all the way down towards the hook portion to hold it out of the way until needed Then locate the best position on the support arm for the second hook and install in the same manner 6 Now the Engine Transverse Bar is ready to use Figure 2 Model 44700 Assembly amp Parts Illustration ASSEMBLY INSTRUCTION FOR MODEL 44100 refer to Figure 3 1 Slide the bigger leg 13 into boom 1 and smaller leg 14 to boom extension 2 Secure the legs by tighten the knob screws 16 The rubber blocks 17 is attached to the bottom of legs 2 Slide transfer adapter 11 over the boom extension 2 with tube toward you 3 Insert the boom extension 2 into boom 1 NOTE The Engine Transverse Bar may be used with or without support arm depending on the load being supported 4 To use without support arm Secure both threaded hooks 3 to the tube welded on boom and transfer adapter with barrel hex nut 7 Thread the nut all the way down towards the hook portion to hold it out of the way until needed 5 To use with support arm a Insert the adjustable leg 6 to support arm 10 then hand tight with M8x65 bolt and wing nut 9 amp 8 Do not fully2. Operating Instructions amp Parts Manual OMEGA Engine Transverse Bar w Support Arm Model Capacity 44700 700 Ib 44100 1000 Ib Model 44700 Model 44100 At is the safety alert symbol It is used to alert you to potential personal injury hazards Obey all safety messages that follow this symbol to avoid possible injury or death e Leer comprender y seguir las instrucci nes antes de utilizar el aparato e El manual de instrucci nes y la informaci n de seguridad deben estar comunicado en lengua del operador antes del uso e No seguir estas indicaci nes puede causar da os personales o materiales SFA Companies http www omegalift com Read this manual and follow all the Safety Rules and Operating Instructions before using this product Printed in China 44700 MO 12 07 SAFETY and GENERAL INFORMATION Save these instructions For your safety read understand and follow the information contained within The owner and operator shall have an understanding of this product and safe operating procedures before attempting to use this product Instructions and Safety information shall be conveyed in the operator s native language before use of this product is authorized Make certain that the operator thoroughly understands the inherent dangers associated with the use and misuse of the product If any doubt exists as to the safe and proper use of this product as out
3. for any purpose other than that for which it is intended e No alterations shall be made to this product e Failure to heed these markings may result in personal injury and or property damage OPERATION 1 Determine the location of the two engine support bolts on your vehicle Then place the Engine transverse bar directly over these two bolts 2 Adjust the boom extension 2 to ensure that both legs 13 amp 14 are sitting inside the fender of the engine compartment Y Ifthe inside fender lips are more than 61 apart apart the Engine Transverse Bar must not be used Do not exceed the designated marking 61 Over extending could cause the Engine Support Bar to collapse resulting in personal injury or property damage 3 Adjust to ensure the support arm 10 is in correct position The rubber tip of the adjustable leg 6 should be on a flat reinforced surface capable of supporting the weight of engine Tighten both wing nuts 4 amp 8 to secure the adjustable leg 6 and support arm 10 4 Lower the threaded hooks 3 to appropriate position Ensure that the hooks are directly over the engine support bolts or brackets therefore the engine does not swing when vehicle is disassembled 5 Attach the looped ends of the two 1 8 braided steel cables 12 to the engine support bolts on the engine and loop middle of braided cables over hooks If the engine being supported is equipped with engine lift brackets h
4. ioraaroo Hardware Kit includes item 3 4 5 7 8 amp 9 1 2 3 4 5 7 10 11 12 13 14 ONE YEAR LIMITED WARRANTY For a period of one 1 year from date of purchase SFA Companies will repair or replace at its option without charge any of its products which fails due to a defect in material or workmanship under normal usage This limited warranty is a consumer s exclusive remedy Performance of any obligation under this warranty may be obtained by returning the warranted product freight prepaid to SFA Companies Warranty Service Department 10939 N Pomona Ave Kansas City MO 64153 Except where such limitations and exclusions are specifically prohibited by applicable law 1 THE CONSUMER S SOLE AND EXCLUSIVE REMEDY SHALL BE THE REPAIR OR REPLACEMENT OF DEFECTIVE PRODUCTS AS DESCRIBED ABOVE 2 SFA Companies SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGE OR LOSS WHATSOEVER 3 ANY IMPLIED WARRANTIES INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE SHALL BE LIMITED TO ONE YEAR OTHERWISE THE REPAIR REPLACEMENT OR REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER AND IS PROVIDED IN LIEU OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED 4 ANY MODIFICATION ALTERATION ABUSE UNAUTHORIZED SERVICE OR ORNAMENTAL DESIGN VOIDS THIS WARRANTY AND IS NOT COVERED BY THIS WARRANTY Some states do not allow limitati
5. k Thread Length Shipping Weight 44700 700 Ib 38 61 27 5 Ib 12 5 44100 1000 Ib 31 0 Ib Threaded Boom Extension 7 Support Arm Boom Leg Adjustable Leg Figure 1 Engine Transverse Bar Components model 44700 shown 2 ASSEMBLY INSTRUCTION FOR MODEL 44700 refer to Figure 2 1 Insert the wide leg 13 into tube welded at the end of boom 1 and the narrow leg 14 to boom extension 2 2 Slide transfer adapter 11 over the end of boom extension 2 with tube toward you 3 Insert the boom extension 2 into boom 1 NOTE The Engine Transverse Bar may be used with or without support arm depending on the load being supported 4 To use without support arm Secure both threaded hooks 3 to the tube welded on boom and transfer adapter with barrel hex nut 7 Thread the hex nut 7 all the way down towards the hook portion to hold it out of the way until needed 5 To use with support arm a Insert the adjustable leg 6 to support arm 10 then hand tight with M8x65 bolt and wing nut 9 amp 8 Do not fully tighten wing nut as height adjustment may be necessary once the Engine Transverse Bar is placed over the engine compartment of the vehicle b After determining the length of support arm needed Connect the support arm 10 to transfer adapter 11 on the boom extension with M12x120 bolt and wing nut 5 amp 4 Again do not fully tighten
6. lined in this factory authorized manual remove from service Inspect before each use Do not use if there are broken bent cracked or otherwise damaged parts including labels Owners and operators of this equipment shall be aware that the use of this equipment may require special training and knowledge It is recommended that an annual inspection be done by qualified personnel and that any missing or damaged decals warning safety labels or signs be replaced with factory authorized replacements only Any engine transverse bar that appears to be damaged in any way is worn or operates abnormally shall be removed from service immediately PRODUCT DESCRIPTION Omega Engine Transverse Bar is designed to safely support engine up to 700 lb It assists the removal of transaxle easily by supporting engine of front wheel drive vehicle Heavy duty steel frame helps prevent distortion and twisting Compliance with factory standards ensures safety strength and stability BEFORE USE 1 Verify that the product and the application are compatible if in doubt call Omega Tech Service 888 332 6419 2 Before using this product read the operator s manual completely and familiarize yourself thoroughly with the product its components and recognize the potential hazards associated with its use 3 Inspect before each use Do not use if bent broken or cracked components are noted 4 Ensure that all parts move freely SPECIFICATIONS Capacity ee Hoo
7. ons on how long an implied warranty lasts so the above limitation may not apply to you Some states do not allow the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights which vary from state to state SFA Companies 10939 N Pomona Ave Kansas City MO 64153 888 332 6419 Nae sales omegalift com
8. ook the hooks 3 directly into engine lift brackets for extra protection Note Use only fasteners rated Grade 5 or higher as engine support bolts 6 Tighten the barrel hex nuts 7 on both hooks until cables are snug or hex nuts are tight against support bar 7 Double check that engine is properly supported before disassemble the vehicle MAINTENANCE Periodically inspect the Engine Transverse Bar Ensure all parts move freely To help prevent rust wipe clean and or blow dry after each use If rust appears sand affected area and cover with suitable utility paint Store the Engine Transverse Bar in a clean dry area REPLACEMENT PARTS Refer to Figure 2 amp 3 Not all components of the Engine Transverse Bar are replacement items but are illustrated as a convenient reference of location and position in the assembly sequence When ordering parts give part number and description Call or write for current pricing SFA Companies 10939 N Pomona Ave Kansas City MO 64153 U S A E Mail sales omegalift com Tel 888 332 6419 Fax 816 891 6599 Omega Website http www omegalift com Parts List op o EN E 2 Boom Extension 7 op o Meer a a o ponm o fema E os faset 7 Bereta a a PCIA o mone E ME IA eae E of EN IS A a rentes 77 2 27007 Braided Stee Cab 18 2 DEA ICI foem f 14 Leg Boom Extension 1 o eros E ej rs 7 IA EIN E i Memar 700 00 reselterza7ao nono tabat
9. tighten wing nut as height adjustment may be necessary once the Engine Transverse Bar is placed over the engine compartment of the vehicle b After determining the length of support arm needed Connect the support arm 10 to transfer adapter 11 on the boom extension with M12x120 bolt and wing nut 5 amp 4 Again do not fully tighten as some length adjustment may be required c Before placing the Engine Transverse Bar over the engine compartment install the two threaded hooks 3 provided Insert one hook to the tube welded on boom 1 and secure with barrel hex nut 7 Thread the nut all the way down towards the hook portion to hold it out of the way until needed Then locate the best position on the support arm for the second hook and install in the same manner 6 Now the Engine Transverse Bar is ready to use T NY L 9 0 Ce gt a M gt ES d an E DON E n ER A 14 E A AT S O E PS E 9 E A 86 lt Q Figure 3 Model 44100 Assembly amp Parts Illustration Study understand and follow all instructions provided before use Do not exceed rated capacity e Do not exceed maximum width e Never crawl under the suspended load for any reason e Ensure that the engine is supported securely before repairing e Do not use this device
Download Pdf Manuals
Related Search