Operating Instructions - Veterinary Instrumentation
Contents
1. BRASSELER USA I DU GCA POWER ACCES ieS Small Bone Power System PneuMicro Operating Instructions Table of Contents Thank you for choosing Brasseler USA as supplier of your small bone powered surgical instrument and accessory needs The information and procedures described in this manual are intended to assist healthcare professionals in the use care cleaning sterilization and long term maintenance of Brasseler USA PneuMicro Small Bone Power System PAGE 2 Table of Contents General Instructions Cautions PAGE 3 High Speed Drill PM MO9 Series PAGE 4 Medium Speed Drill PM M10 Series PAGE 5 Wiredriver PM M11 Series PAGE 7 Sagittal Saw PM M12 Series PAGE 8 Oscillating Saw PM M13 Series PAGE 9 Reciprocating Saw PM M14 Series PAGE 10 Air Nitrogen Hose KM A90 Series PAGE 11 Cleaning Procedure PAGE 12 Accidental Immersion Recommended Sterilization Procedures PAGE 13 Trouble Shooting Warranty PAGE 14 Explanation of Symbols Repair Service Return Goods Policy PAGE 15 Product Ordering Information Brasseler USA offers a complete line of PneuMicro consumables disposables burs saw blades rasps K wires Steinman pins and twist drills eO S ij General Instructions Cautions Only medical professionals who are thoroughly familiar with the instrument s function application and instructions for use should operate any Brasseler USA powered surgical instrument Brasseler USA PneuMicro2. the bur head should ras s Wardle mies NA and the locking collar is in the locked position extend no more than 1 in 2 5 cm from the end of the bur guard Select the proper bur guard for length of the bur to be used See pg 4 Figure 4 for The speed of the instrument is controlled by the throttle medium burs Brasseler USA catalog PM M10 901 Jever and will depend on the operating air or nitrogen for long burs Brasseler USA catalog PM M10 902 pressure Do not exceed the recommended maximum for extra long burs Brasseler USA catalog PM M 10 operating pressure of 110 psi 7 6 kg cm Lower 903 Fully seat the bur guard onto nose of drill pressure setting will achieve lower maximum speed Figure 3 Sudden activation of the instrument throttle lever will start the instrument immediately at high speed For this l reason a careful slow activation of the throttle lever is 5 Insert Bur Insert the bur into the bur guard and recommended By correct application of the throttle seat it fully into the locking mechanism The fully lever various operating speeds can be achieved inserted bur should not extend more than 1 in 2 5 cm from the tip of the bur guard Note Do not use burs without bur guard Small Bone Power System PneuMicro Operating Instructions Medium Speed Drill PM M10 Series E TECHNICAL DESCRIPTION m Speed O 25 000 rpm m Torque 6 0 in oz 4 24 N cm m Operating Pressure 90 110
3. USA catalog KM A90 Series Hoses Confirm by checking the regulator pressure gauge that operating pressure does not exceed 110 psi 7 6 kg cm Move throttle safety slide to the ON position fully backward to activate instrument See pg 3 Figure 2 Your PneuMicro Oscillating saw is ready for use 3 Open Collet Open loosen the blade locking screw with the blade wrench Brasseler USA catalog PM M12 001 by turning it counterclockwise Figure 10 PM M12 001 Included with handpiece or can be purchased separately e ID 4 Insert Saw Blade Insert the saw blade under the compression washer The saw blade must be fully inserted for proper engagement Lock tighten the blade locking screw hand tight with the blade wrench by turning it clockwise Figure 10 The saw blade may be positioned anywhere within a 180 arc Confirm that the saw blade is secure by tugging slightly on the saw blade Activate the instrument briefly and then re tighten the blade locking screw to ensure that the saw blade is fully locked in place The speed of the instrument is controlled by the throttle lever and will depend on the operating air or nitrogen pressure Do not exceed the recommended maximum operating pressure of 110 psi 7 6 kg cm Lower pressure setting will achieve lower maximum speed Sudden activation of the instrument throttle lever will start the instrument immediately at high speed For this reason a careful slow act
4. Remove attachments bur guard and accessories air nitrogen hose or cleaning cap prior to sterilization BRISTLES LU9 SAS JAMOd U0g JDWS ODINN Ud 11 e ID Operating Instructions Accidental Immersion If accidental immersion of the handpiece occurs please follow these recommended procedures D 1 Immediately wash rinse instrument under running 3 Attach the instrument to medical grade air or nitrogen Q water see 5 in cleaning procedure and operate the V instrument for a minimum of 30 seconds k ts 2 Immerse instrument in clean rinse water preferably de ionized or distilled for 1 3 minutes The goal is O to rinse away any corrosive fluids and precipitates Q 00 ieee 5s Recommended Sterilization Procedures a Steam sterilization has been found both safe Air nitrogen hose or cleaning cap must be removed 5 and effective for the sterilization of Brasseler from instrument USA PneuMicro small bone powered Q U instruments and air nitrogen hoses The instruments are If instruments require being wrapped two double thick capable of withstanding the recommended exposure 140 thread count wrappers or equivalent should be times and temperatures of steam sterilization utilized Do not sterilize instruments or air nitrogen hoses in Ethylene Note The sterilizer manufacturers written instruction for cycle parameters load configuration and AAMI guidelines for steam steri
5. Series Hoses Confirm by checking the regulator pressure gauge that operating pressure does not exceed 110 psi 7 6 kg cm Move throttle safety slide to the ON position fully backward to activate instrument See pg 3 Figure 2 Your PneuMicro Sagittal Saw is ready for use 3 Open Collet Open loosen the blade locking screw with the blade wrench Brasseler USA catalog PM M12 001 by turning it counterclockwise Figure 9 cs el 4 Insert Saw Blade Abrader Insert the saw blade abrader between the two washers forming a slot The saw blade abrader must be fully inserted for proper engagement Lock tighten the blade locking screw hand tight with the blade wrench by turning it clockwise Figure 9 The saw blade abrader may be positional anywhere within a 180 arc Confirm that the saw blade abrader is secure by tugging slightly Activate the instrument briefly and then re tighten the blade locking screw to ensure saw blade abrader is fully locked in place The speed of the instrument is controlled by the throttle lever and will depend on the operating air or nitrogen pressure Do not exceed the recommended maximum operating pressure of 110 psi 7 6 kg cm Lower pressure setting will achieve lower maximum speed WaJSAS JAMOd IUD DUS ODINN Ud Sudden activation of the instrument throttle lever will start the instrument immediately at high speed For this reason a careful slow activation of the throt
6. WaJSAS JAMOd IUD DUS ODINN Ud Operating Procedure When instrument is not in use but connected to medical grade air or nitrogen supply the throttle safety slide must be placed in the SAFE position fully forward to avoid accidental activation of instrument Figure 1 I Bur Guard Installation 1 Safety On Move the throttle safety slide to the SAFE position fully forward CAUTION THE PNEUMICRO PM M09 SERIES HIGH 2 System Set Up Connect the instrument to the SPEED DRILL MAY HEAT UP RAPIDLY IF air nitrogen supply hose Brasseler USA catalog KM THE LOCKING COLLAR IS NOT FULLY A90 Series Hoses Confirm by checking the regulator ROTATED INTO THE LOCK POSITION pressure gauge that operating pressure does not exceed EXCESSIVE HEAT MAY RESULT IN DAMAGE 110 psi 7 6 kg cm Move throttle safety slide to the TO INSTRUMENT OR INJURY TO THE ON position fully backward to activate instrument PATIENT AND OR OPERATOR Figure 2 Your PneuMicro High Speed Drill is ready for use 6 Lock Bur Rotate the locking collar into the Lock position a click can be felt when fully secure Tug 3 Open Collet Unlock the bur locking mechanism by slightly on bur to ensure it is fully locked in place rotating the locking collar into the open position a click can be felt as the collet fully opens Note The PneuMicro PM M09 series High Speed Drill will not operate unless a bur is fully inserted 4 Bur Guard Use
7. andpiece lacks m Internal Malfunction power or does m Incorrect operating pressure not operate m Tank pressure low below 500 psi m Throttle safety slide directional lever is partially in safe position m Hose not installed properly m Tank valve not opened fully m Regulator malfunction Hose pinched Solution Return handpiece for service Set pressure to correct operating pressure for length of hose See instructions on page 2 Replace tank before using handpieces Ensure throttle safety slide directional lever is in operating position Check all hose connections for proper installation Completely open tank valve Replace regulator and retest handpiece If symptom continues return handpiece for service Inspect hose and remove restriction LU9 SAS JAMOd U0g JDWS ODINN Ud Drills Bur is not Bur is not locked in handpiece retained in Bur is not fully inserted into collet handpiece m Wrong style bur Handpiece overheats Bur guard bearings worn Collet not fully closed Internal malfunction Incorrect operating pressure No bur in collett Blade vibrates loose Blade is not fully seated Blade is not locked in collet Blade locking nut is worn m Wrench is worn m Ensure locking ring is in the lock position Insert bur completely into collet and lock collet See instructions on pages 5 4 6 Check manufacturers recommended bur guards and speeds for
8. ge of diameter sizes WaJSAS JAMOd IUD DUS ODINN Ud Note Brasseler USA K Wire Catalog Series KM172 amp 173 Brasseler USA Steinmann Pin Catalog Series KM168 amp KM169 Operating Procedure When instrument is not in use but connected to medical grade air or nitrogen supply the activation directional lever must be placed in the SAFE position center to avoid accidental activation of instrument Figure 5 1 Safety On Move the activation directional lever to the SAFE position center 2 System Set Up Connect the instrument to the air nitrogen supply hose Brasseler USA catalog iFKM A90 Series Hoses Confirm by checking the regulator pressure gauge that operating pressure does not exceed 110 psi 7 6 7 kg cm Assure the activation directional lever on the handpiece is in the SAFE position Your PneuMicro Wiredriver is ready for use 3 Insert Wire Insert the wire six inches or longer either through the front or back of the cannulated handpiece Figure 6 If inserting a wire through the front of the wiredriver care must be taken to align the wire with the collet opening to avoid jamming in the collet Wires shorter than six inches must be loaded through the front of the handpiece Insert the wire until the desired length is protruding from the collet nose of the handpiece The inserted wire should protrude approximately 1 in 2 5 cm from the tip of the collet nose Fi
9. gure 7 The cannulated wire guard Brasseler USA catalog PM M11 201 may be used to Inserted Wire prevent bending of longer wires Attach the wire guard by threading the guard into the back of the handpiece See pg 6 Figure 8 OR s Operating Instructions Wiredriver PM M11 Series 4 Clamp Wire Slightly depress the trigger to lock the collet onto the wire 5 Drive Wire To advance the wire the collet end of the handpiece should be at least 1 4 to 1 2 in 8 6 to 13 mm away from the bone Place the activation directional lever in the desired position FORWARD or REVERSE and depress the trigger To expose more wire completely release the trigger and pull the handpiece back along the wire Slightly depress the trigger again to lock the collet Depress the trigger to activate the handpiece for further insertion of the wire Note The handpiece must be in the REVERSE position to remove threaded wires and pins Small Bone Power System PneuMicro Instrument Speed The variable speed of the instrument is controlled by the instrument trigger and depends on the operating air or nitrogen pressure Do not exceed the recommended maximum operating pressure of 110 psi 7 6 kg cm Attaching Wire Guard If the handpiece lever is in FORWARD or REVERSE position the instrument will start at maximum speed if the trigger is depressed fully A slow activation of the 6
10. h PM M12 001 Blade Wrench Brasseler USA offers a complete line of PneuMicro consumables disposables burs saw blades rasps K wires Steinman pins and twist drills Linvatec Hall and Synthes are not a registered trademark of Brasseler USA BRASSELER USA SURGICAL POWER amp ACCESSORIES One Brasseler Boulevard Savannah Georgia 31419 912 925 8525 800 535 6638 912 921 7578 fax www BrasselerUSAMedical com Order Information USA 8 Canada 1 800 545 6648 or 1 912 925 8525 Linvatec and Hall are registered trademarks of Linvatec Corporation Brasseler USA and Zimmer Orthopaedic Surgical Products Inc are not affiliated with any of the above and makes no claim to copyrights or trademarks which are the property of these companies Brasseler USA and PneuMicro are trademarks of Brasseler USA Inc All rights of distribution also by photocopy reprint or storing and recovery in any kind of data processing are reserved and require our written approval Color and products subject to alterations 2007 Brasseler USA Medical LLC All rights reserved Printed in the U S A BM 2948 1M 08 07 RRD
11. handpiece being used Return bur guard for service Ensure locking ring is in the lock position Return handpiece for service Set pressure to correct operating pressure for length of hose See instructions on page 2 m Install proper bur and proper bur guard m Ensure blade is fully secured in handpiece collet m Briefly activate the handpiece and retighten blade locking nut m Return handpiece for service m Replace Wiredriver Wire will not Insert into collet m Wire not in size range of collet m Debris in collet Warranty Brasseler USA Surgical Power amp Accessories warrants all PneuMicro instruments handpieces to be free from defects in material and workmanship for a period of one 1 year from the original purchase date The Brasseler USA PneuMicro attachments bur guards and accessories hoses cleaning cap foot control sterilization cases adapter DISS to Schrader wire guard wire brush and blade wrench are warranted for six 6 months from the original purchase m Check size to ensure it is between 028 in and 078 in m Clean collet using wire brush date The warranty is limited to the repair of the product without charge This warranty is void in the event of any of the following abuse misuse or use in other than normal surgery environment disassembly alteration or unauthorized repair or in the event that the product has not been used in reasonable manner and in compliance with the writte
12. instrument trigger is recommended PM M11 201 Wire Guard PM M11 202 U Wire Brush Included with handpiece or can be purchased separately Wiredriver Accessories D Operating Instructions Sagittal Saw PM M12 Series TECHNICAL DESCRIPTION m Speed O 18 000 cpm m Blade Travel 4 arc m Operating Pressure 90 110 psi 6 2 7 6 kg cm The PneuMicro PM M12 Series Sagittal Saw has the power and precision needed for cutting both wedge and transverse osteotomies while allowing excellent visibility to the surgical site Smooth cutting and easy to control the instruments saw blade may be positioned anywhere within a 180 arc The saw blade collet accepts a wide variety of 010 in 25 mm and 025 in 0 6 mm thick Brasseler USA straight and angled sagittal saw blades diamond abraders Note Brasseler USA Sagittal Saw Blade Catalog Series KM 3100 KM 3200 KM 3400 and Sagittal Diamond Abraders KM 3055 KM 3056 and KM 3057 Operating Procedure When instrument is not in use but connected to medical grade air or nitrogen supply the throttle safety slide must be placed in the SAFE position fully forward to avoid accidental activation of instrument See pg 3 Figure 1 1 Safety On Move the throttle safety slide to the SAFE position fully forward 2 System Set Up Connect the instrument to the air nitrogen supply hose Brasseler USA catalog KM A90
13. instruments handpieces are recommended to be powered by medical grade air or nitrogen dry 99 7 pure and filtered to five 5 microns Always use the recommended operating pressure and verify it at the regulator pressure gauge The recommended operating pressure setting for optimum performance is 90 110 psi 6 2 7 6 kg cm Lower settings can be used for slower speed requirements if necessary Do not exceed 110 psi 7 6 kg cm operating pressure for PheuMicro instruments Note For optimum performance when using an air nitrogen hose longer than 10 feet 3 m increase pressure by 1 psi for each additional 1 foot length of hose Use of eye face protection device s recommended while operating powered instruments When instrument is connected to supply source and not being used or loading consumables disposables burs saw blades rasps K wires Steinman pins and twist drills into the instrument the throttle trigger must be in the SAFE position to avoid unintended activation of the instrument Application of excessive force to instrument may cause damage to instrument and or consumable or injury to patient and or operator For optimum results use new consumable for every procedure Check consumables for damage before and during use If consumable seems to be damaged discontinue its use Test the instrument before each use With face protected and appropriate consumable fully inserted and locked into the instrumen
14. ions Air Nitrogen Hose KM A90 Series Hoses Small Bone Power System PneuMicro Connecting Hose to Instrument Operating Procedure 10 1 Supply Side Connection Connect the male 3 Operation Turn on supply valve and adjust Schrader connector on the end of hose by pushing operating pressure from 90 to 110 psi 6 2 to 7 6 it into the female Schrader connector fitting of the kg cm The hose is operational at this time regulator or the regulated air nitrogen source Note For optimum performance when using a Note A DISS to Schrader Adapter Brasseler USA hose longer than 10 feet 3 m increase pressure Catalog MI 121 001 is available when a female by 1 psi for each additional 1 foot length of hose DISS connector is required at the regulator or the regulated air or nitrogen supply source 4 Disconnecting Hose From Supply Source Release the hose from the supply source by firmly Insert the male Schrader connector on the holding the hose connector and then twist the air nitrogen hose Brasseler USA Catalog KM A90 supply source Schrader connector sleeve Series Hoses into the female Schrader connector on the Adapter and then attach the female DISS Note To prevent sudden ejection of hose from connector on the Adapter to the male DISS connector the supply source hold the hose connector firmly at the regulator or regulated air or nitrogen source 5 Disconnecting Hose From the Instrument 2 Connecting I
15. ivation of the throttle lever is recommended By correct application of the throttle lever various operating speeds can be achieved Blade Installation Blade Wrench Operating Instructions Reciprocating Saw PM M14 Series TECHNICAL DESCRIPTION m Speed O 18 000 rpm m Blade Travel 078 in 2 0 mm m Operating Pressure 90 110 psi 6 2 7 6 kg cm The PneuMicro PM M14 Series Reciprocating Saw is an extremely versatile instrument and an outstanding performer for creating long osteotomies on the foot or oral maxillofacial operations The sawblade rasp collet accepts flat shank saw blades from 014 in to 020 in 35 mm to 51 mm thick as well as rasps and round shank saw blades with standard diameters of 125 in 3 18 mm Note Brasseler USA Reciprocating Saw Blade Rasp Catalog KM 50 Series KM 80 Series and KM 060 amp KM 070 Operating Procedure When instrument is not in use but connected to medical grade air or nitrogen supply the throttle safety slide must be placed in the SAFE position fully forward to avoid accidental activation of instrument See pg 3 Figure 1 1 Safety On Move the throttle safety slide to SAFE position fully forward 2 System Set Up Connect the instrument to the air nitrogen supply hose Brasseler USA catalog KM A90 Series Hoses Confirm by checking the regulator pressure gauge that operating pressure does not exceed 110 psi 7 6 kg c
16. lization should be followed Oxide Sterrad System Steris System or comparable sytems Do not use Cidex to sterilize instruments or hoses Do not place instruments in a peel pouch for sterilization The following parameters are provided as guidelines and do not guarantee that the devices are sterile Sterility assurance validation is the responsibility of your institution Parameters for sterilizing Pneumicro handpiece in Sterilization Case Steam Sterilization Recommended Recommended Minimum Recommended Minimum Temperature Exposure Time Dry Time Pre Vacuum 270 279 F 4 minutes 8 minutes 132 137 C 273 279 F 3 minutes 8 minutes 134 137 C Sterilization case Brasseler USA catalog PM A95 000 has been validated to sterilize up to three PneuMicro Handpieces three bur guards one blade wrench one wire guard and one air nitrogen hose Parameters for sterilizing individually wrapped PneuMicro products including handpieces attachments and accessories Steam Sterilization Recommended Recommended Minimum Recommended Minimum Temperature Exposure Time Dry Time Gravity 270 279 F 35 minutes 8 minutes 132 137 C Pre Vacuum 270 279 F 4 minutes 8 minutes 132 137 C 273 279 F Z minutes 8 minutes IZF 137C Sterrad Steris and Cidex are not register trademarks of Brasseler USA i U Z Operating Instructions Trouble Shooting Symptom Potential Cause All Handpieces H
17. m Move throttle safety slide to the ON position fully backward to activate the instrument See pg 3 Figure 2 Your PneuMicro Reciprocating Saw is ready for use 3 Open Collet Open loosen the blade rasp locking nut by turning it counterclockwise Figure 11 Do not remove the locking nut from the tip 4 Insert Saw Blade Rasp Insert the saw blade rasp fully into the locking mechanism The saw blade rasp must be fully inserted for proper engagement Lock tighten the blade rasp locking nut finger tight by turning it clockwise Figure 11 Confirm that the saw blade rasp is secure by tugging slightly on the saw blade rasp Activate the instrument briefly and then re tighten the blade rasp locking nut to ensure saw blade rasp is fully locked in place eal aa K The speed of the instrument is controlled by the throttle lever and will depend on the operating air or nitrogen pressure Do not exceed the recommended maximum operating pressure of 110 psi 7 6 kg cm Lower pressure setting will achieve lower maximum speed Sudden activation of the instrument throttle lever will start the instrument immediately at high speed For this reason a careful slow activation of the throttle lever is recommended By correct application of the throttle lever various operating speeds can be achieved Blade Installation vu WaJSAS JAMOd IUD DUS ODINN Ud anna S iii I Operating Instruct
18. maximum speed Sudden activation of the instrument throttle lever will start the instrument immediately at high speed For this reason a careful slow activation of the throttle lever is recommended By correct application of the throttle lever various operating speeds can be achieved a PM M10 901 Medium Brasseler USA Bur Catalog Series 03 04 06 07 amp 08 Recommended Bur Length 44 5 69 mm Ha PM M10 902 Long Brasseler USA Bur Catalog Series 09 10 amp 11 Recommended Bur Length 70 94 mm m PM M10 903 Extra Lon Brasseler USA Bur Catalog Series 65 Recommended Bur Length 95 112 mm lt Bur Guards D Do not use the following Brasseler USA Dermabrader Burs in the PM MO9 Series High Speed Drill 03 D1901 03 D 1902 04 D1093 and 04 D2001 V Operating Instructions F eat Wiredriver PM M11 Series TECHNICAL DESCRIPTION m Speed O 2 100 rpm m Torque 45 in oz 31 8 N cm m Operating Pressure 90 110 psi 6 2 7 6 kg cm m Wire Pin Diameter Range 0 028 0 078 in 0 7 2 0 mm The PneuMicro PM M11 Series Wiredriver with its ergonomically designed pistol grip handle operates at throttle controlled speeds with ample power for small bone fixation The compact and lightweight design allows access to the smallest of surgical sites The Wiredriver collet accepts both smooth plain and threaded K Wires and Steinman Pins in a wide ran
19. must be cleaned after each use to ensure proper functioning of the Wiredriver 3 With the air nitrogen hose or cleaning cap still attached rinse all traces of contaminants and detergent under running water DO NOT IMMERSE If accidental immersion of the handpiece occurs please refer to section Accidental Immersion 4 Disconnect the air nitrogen hose or remove the cleaning cap Shake the instrument and any attachment free of excess water Note The PM MO9 and PM M10 series drills cannot be operated without inserting proper bur guard and locking a bur into the collet 5 Drills and Saws Move throttle control safety slide to SAFE full forward position See pg 3 Figure 1 Connect air nitrogen hose to medical grade air or nitrogen supply regulated to 90 110 psi or 6 2 7 6 kg cm Move throttle safety slide to ON position full backward activate instrument for 5 10 seconds See pg 3 Figure 2 Check for rapid temperature rise Unusual noise s and other visible malfunctions 6 Wiredriver Move lever to SAFE center position See pg 5 Figure 5 Connect air nitrogen hose to medical grade air or nitrogen supply regulated to 90 110 psi or 6 2 7 6 kg cm Move lever to FORWARD position left activate instrument for 5 10 seconds Repeat with lever in REVERSE Move throttle lever to the SAFE position and disconnect air nitrogen hose from instrument 9 Do not lubricate instruments Note
20. n instructions furnished by Brasseler USA Surgical Instruments Small Bone Power System PneuMicro Operating Instructions Explanation of Symbols Refer to the Operation Instructions Manual Repair Service Brasseler USA recommends that all powered instruments handpieces attachments and accessories be returned for preventative maintenance every six 6 months Brasseler USA warrants any service or repair work performed will be free from defects in material or workmanship for the period of six 6 months from date of service or repair This warranty applies to the actual work performed Products must be sterilized and decontaminated before returning Note It is unlawful to ship contaminated non sterilized products Return Goods Policy Brasseler USA unconditionally guarantees the quality of each of our products their performance and your satisfaction with those products If product needs to be returned the following applies Consumable Disposable Product Consumable product s returned for credit must be received within 90 days of purchase date and qualify for resale prior to a credit being issued or may be subject to an additional restocking fee Capital Equipment Capital equipment returned for credit must be received within 30 days of purchase date and qualify for resale prior to a credit being issued or may be subject to an additional restocking fee Credit will be issued for incorrectly o
21. name address and account number A packing list ttemizing each product being returned m Enclose brief statement describing reason for product return Return to Brasseler USA 4837 McGrath Street Suite J Ventura CA 93003 a Operating Instructions Product Ordering Information CATALOG DESCRIPTION NUMBER HANDPIECES WITH LINVATEC HALL HOSE CONNECTION PM M09 200 High Speed Drill PM M10 200 Medium Speed Drill PM M11 200 Wiredriver with Guard amp Brush PM M12 200 Sagittal Saw with Wrench PM M13 200 Oscillating Saw with Wrench PM M14 200 Reciprocating Saw HANDPIECES WITH SYNTHES HOSE CONNECTION PM M09 500 High Speed Drill PM M10 500 Medium Speed Drill PM M12 500 Sagittal Saw with Wrench PM M13 500 Oscillating Saw with Wrench PM M14 500 Reciprocating Saw LU9 SAS JAMOd U0g JDWS ODINN Ud ATTACHMENTS PM M10 901 Bur Guard Medium PM M10 902 Bur Guard Long PM M10 903 Bur Guard Extra Long ACCESSORIES KM A90 200 Air Nitrogen Hose with Linvatec Hall Hose Connection 10 Ft KM A90 200 15 Air Nitrogen Hose with Linvatec Hall Hose Connection 15 Ft KM A90 201 Cleaning Cap with Linvatec Hall Hose Connection KM A91 000 Foot Control KM A95 000 Sterilization Case Small 11 in x 7 in x I in MI 121 001 Adapter DISS to Schrader PM A90 501 Cleaning Cap with Synthes Hose Connection PM A95 000 Sterilization Case Large 12 in x 7 in x 4 in PM M11 201 Wire Guard PM M11 202 Wire Brus
22. nstrument Hold securely in one Hold instrument hose connector end and connector hand the hose connector end of the instrument on hose firmly and push them slightly together to Hold firmly in the other hand the connector of the remove the pins from the detents of the bayonet hose and align the pins on the connector with slots After twisting the hose connector slowly move the bayonet slots in the hose connector of the it away from the instrument instrument Figure 12 Push both together and twist the connector so the pins slide into the bayonet slots and seat in the detents for positive locking Release hose it will stay attached to the instrument If connection is correct i Operating Instructions Cleaning Procedure Leave air nitrogen hose attached or insert the cleaning cap into the hose connector of the instrument Remove attachments bur guards accessory wire guard and consumables disposables burs saw blades rasps K wires Steinman pins and twist drills prior to cleaning 1 Scrub using a nylon brush the instruments attachments bur guards and accessories thoroughly with mild soap and water Remove all traces of blood and debris 2 Wiredriver Cannulation Cleaning Insert the Wire Brush Brasseler USA catalog PM M 11 202 through the back of handpiece Figure 13 Pull the brush through the handpiece Repeat the process until all debris is removed Note The cannulation of both the Wiredriver and Wire Guard
23. psi 6 2 7 6 kg cm The PneuMicro PM M10 Series Medium Speed Drill operates at throttle controlled speeds with ample power for small bone cutting drilling sculpting and intramedullary canal reaming The compact and lightweight design allows access to the smallest of surgical sites The bur collet accepts a wide range of medium long and extra long burs as well as drill bits with shank diameters of 0919 in to 0929 in 2 33 to 2 36 mm Bur guards are available and must be used with medium long and extra long burs Figure 4 Operating Procedure When instrument is not in use but connected to medical grade air nitrogen supply the throttle safety slide must be placed in the SAFE position fully forward to avoid accidental activation of instrument See pg 3 Figure 1 1 Safety On Move the throttle safety slide to the SAFE position fully forward 2 System Set Up Connect the instrument to the air nitrogen supply hose Brasseler USA catalog KM A90 Series Hoses Confirm by checking the regulator pressure gauge that operating pressure does not exceed 110 psi 7 6 kg cm Move throttle safety slide to the ON position fully backward to activate instrument See pg 3 Figure 2 Your PneuMicro Medium Speed Drill is ready for use 3 Open Collet Unlock the bur locking mechanism by rotating the locking collar into the open position a click can be felt as the collet fully opens 4 Bur Guard Use In gene
24. ral the bur head should extend no more than 1 in 2 5 cm from the end of the bur guard Select the proper bur guard for length of the bur to be used Figure 4 for medium burs Brasseler USA catalog PM M10 901 for long burs Brasseler USA catalog PM M10 902 for extra long burs Brasseler USA catalog PM M10 903 Fully seat the bur guard onto nose of drill See pg 3 Figure 3 Note Do not use burs without bur guard i _ _ _ 5 Insert Bur Insert the bur into the bur guard and seat it fully into the locking mechanism The fully inserted bur should not extend more than 1 in 2 5 cm from the tip of the bur guard 6 Lock Bur Rotate the locking collar into the Lock position a click can be felt when fully secure Tug slightly on bur to ensure it is fully locked in place Note The PneuMicro PM M10 series Medium Speed Drill will not operate unless a bur is fully inserted and the locking collar is in the locked position CAUTION THE PNEUMICRO PM M10 SERIES MEDIUM SPEED DRILL MAY HEAT UP RAPIDLY IF THE LOCKING COLLAR IS NOT FULLY ROTATED INTO THE LOCK POSITION EXCESSIVE HEAT MAY RESULT IN DAMAGE TO INSTRUMENT OR INJURY TO THE PATIENT AND OR OPERATOR The speed of the instrument is controlled by the throttle lever and will depend on the operating air or nitrogen pressure Do not exceed the recommended maximum operating pressure of 110 psi 7 6 kg cm Lower pressure setting will achieve lower
25. rdered product and incorrect product shipped Capital equipment that has been used does not qualify for resale and credit will not be issued Packaging and Shipping Package items in original packaging as credit cannot be issued for items damaged in return shipment due to packaging inadequacy cs DO NOT IMMERSE e C7 Steam Sterilize Contact a Customer Service Representative at Brasseler USA Headguarters at 800 535 6638 to report a repair and or to obtain a loaner instrument if needed Loaner instruments can be supplied depending on availability of stock Please include the following information with the returned product s for repair Model 8 Serial Number of Instrument m Note customer name address and account number m A packing list itemizing each product being returned m Enclose brief statement describing reason for product repair Return to Brasseler USA Service Department 4837 McGrath Street Suite J Ventura CA 93003 Note It is unlawful to ship contaminated non sterilized products Contact a Customer Service Representative at Brasseler USA Headquarters at 800 535 6638 to obtain a Return Merchandise Authorization RMA number Please include the following information with the returned product s m Model amp Serial Number of Instrument m Return Merchandise Authorization number noted with the return m Note the Original Invoice Number or place a copy in the package M Note customer
26. t activate the handpiece for 5 10 seconds Check for rapid temperature rise unusual noise s and other visible malfunctions Never use a malfunctioning damaged or suspected to be damaged instrument Return it to Brasseler USA for prompt service Do not drop throw or hit instrument against any surface Do not immerse instrument Never clean a powered instrument in an automated disinfecting washer or an ultrasonic cleaner Do not start a surgical procedure if the nitrogen tank pressure is less than 500 psi 35 kg cm Do not pinch clamp or crimp air nitrogen supply hose To assure safety and optimum results use only Brasseler USA instruments attachments accessories and consumables Do not lubricate powered surgical instruments vu Operating Instructions High Speed Drill PM MO9 Series TECHNICAL DESCRIPTION m Speed O 95 000 rpm m Torque 1 75 in oz 1 24 N cm m Operating Pressure 90 110 psi 6 2 7 6 kg cm The PneuMicro PM MO09 Series High Speed Drill operates at throttle controlled speeds with ample power for cutting and sculpting small bone and enamel The compact and lightweight design allows access to the smallest of surgical sites The bur collet accepts a wide range of medium long and extra long burs with shank diameters of 0919 in to 0929 in 2 33 to 2 36 mm Bur guards are available and must be used with medium long and extra long burs See page 4 Figure 4
27. tle lever is recommended By correct application of the throttle lever various operating speeds can be achieved z 7 Blade Installation PM M12 001 Included with handpiece or can be purchased separately Blade Wrench Small Bone Power System PneuMicro Operating Instructions Oscillating Saw PM M13 Series ce TECHNICAL DESCRIPTION m Speed O 22 000 cpm m Blade Travel 7 arc m Operating Pressure 90 110 psi 6 2 7 6 kg cm The PneuMicro PM M13 Series Oscillating Saw has a long narrow nose design for accessing restricted areas and to provide excellent visibility of the surgical site The saw delivers the power necessary for accurate cutting of both curved and straight osteotomies The instrument s saw blade may be positioned anywhere within a 180 arc The saw blade collet accepts a wide selection of the Brasseler USA straight and angle shaped oscillating saw blades Note Brasseler USA Oscillating Saw Blade Catalog Series KM 3000 Operating Procedure When instrument is not in use but connected to medical grade air or nitrogen supply the throttle safety slide must be placed in the SAFE position fully forward to avoid accidental activation of instrument See pg 3 Figure 1 1 Safety On Move the throttle safety slide to the SAFE position fully forward 2 System Set Up Connect the instrument to the air nitrogen supply hose Brasseler
Download Pdf Manuals
Related Search