Important /Note! Read the operating instructions
Contents
1.2. Note A Important Note Read the operating instructions CE Consult instructions thoroughly before use Classification A Internally powered equipment BF BF type applied part IPXO Not suitable for use in presence of flammable anaesthetic mixture with air or with Oxygen or nitrous oxide Continuous operation with short time loading electromagnetic interference between electrical and electronic equipments do not use the device near a cell phone or microwave oven D4 Discard the used product to the recycling collection point according to local regulations a To avoid inaccurate results caused by imited Warranty This device is warranted to be free from manufacturing defects for i period of 2 years from the date of purchase Within the warranty yeriod should there be any manufacturing defect found and repair s needed please contact your local distributor accordingly lease note warranty does not cover damage caused by acluding but not limited misuse or abuse accident the ittachment of any unauthorized accessory alteration to the oduct improper installation unauthorized repair or modification nproper use of electrical power supply dropped product failure o follow required maintenance and sake keeping transportation lamage o ensure precise measurement reading recalibration of the levice is recommended after 2 years from the date of purchase shipping plus handling cost and recalibration service fe
3. d dry it immediately with a dry cloth 8 2 Do not use detergent or any strong chemicals to clean the device 8 3 Use only a dry cloth to wipe the cuff 8 4 If the device is not to be used for a long time please remove the batteries from the device leaking of battery acid can cause the device to malfunction 8 5 Do not in any way twist the cuff 8 6 Do not press the START button if the cuff is not wrapped around the wrist 8 7 Do not drop the product and avoid any strong impacts 8 8 Do not attempt to disassemble or change any parts of the monitor including wrist cuff due to substitution of a component different from that supplied might result in measurement error 8 9 If any suggestion or service is requested please consult your service station 8 10 Do not place the device directly under sunlight in high temperature or in humid or dusty places 8 11 Do not store the device in extremely low less than 4 F 20 C or high more than 158 F 70 C temperature A WHO blood pressure classifications Standards for assessment of high or low blood pressure without regard to age have been Pane established by the World Health Organization WHO as shown in the chart Optimal Severe hypertension Moderate hypertension Mild hypertension 120 130 140 150 160 170 180mm Systolic Blood Pressure systue Figure No 1 B Variations in blood pressure Blood pressure naturally varies from time to time thro
4. e shall be harged accordingly Note his equipment has been tested and found to comply with the mits for Class B digital device pursuant to part 15 of the FCC tules hese limits are designed to provide reasonable protection igainst harmful interference in a residential installation his equipment generates uses and can radiate radio frequency nergy and if not installed and used in accordance with the structions may cause harmful interference to radio or television aceptions which can be determined by turning the equipment off ind on The user is encouraged to try to correct the interference by ine or more of the following yeasures Reorient or relocate the receiving antenna Increase the separation between the equipment and the receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected onsult the dealer or an experienced radio TV technician for help ppendix s uidance and manufacturer s declaration electromagnetic emissions he device is intended for use in the electromagnetic environments listed below and should inly be used in such environments Electromagnetic environment guidance imissions test Compliance F emissions Group 1 RF energy is used only to maintain device s operation ASPR 11 Therefore its RF emissions are so low that it s not likely to cause any interference in nearby electronic equipment The device is suitable for
5. es are hazardous waste Do not dispose of them together with the household garbage Please take the used batteries to the recycling collection point according to your local regulations Keep the battery away from small children To prolong the battery life and prevent damage caused by leakage remove the batteries from the device if the device is not to be used for a long period After replacing the batteries reset the date and time All batteries used must be the same type Do not mix alkaline standard carbon zinc or rechargeable cadmium batteries Do not mix old and new batteries uidance and manufacturer s declaration electromagnetic immunity The device is intended for use in the electromagnetic environments listed below and should only be used in such environments IEC 60601 Compliance Electromagnetic environment guidance Floors should be wood concrete or ceramic tile If floors are covered with synthetic material the relative humidity should be at least 30 Power frequency magnetic fields should be at levels characteristic of a typical location in a typical commercial or hospital environment EC 61000 4 8 Guidance and manufacturer s declaration electromagnetic immunity The device is intended for use in the electromagnetic environments listed below and should only be used in such environments immunity IEC 60601 Compliance Electromagn
6. etic environment guidance test test level_ level Portable and mobile RF communications equipment should be used no closer to any part of the device including cables than the recommended separation distance calculated from the equation applicable to the frequency of the transmitter Recommended separation distance d 12 P d 1 2 gt 80 MHz to 800 MHz d 23 P 800 MHz to 2 5 GHz where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer and d is the recommended separation distance in metres m Field strengths from fixed RF transmitters as determined by an electromagnetic site survey a should be less than the compliance level in each frequency range b Interference may occur in the vicinity of equipment marked with the following symbol A NOTE 1 At 80 MHz and 800 MHz the higher frequency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people a Field strengths from fixed transmitters such as base stations for radio cellularicordless telephones and land mobile radios amateur radio AM and FM radio broadcast and TV broadcast cannot be predicted theoretically with accuracy To assess the electromagnetic environment due to fixed RF transmitters an electromagnetic site survey should be considered If the meas
7. g blood pressure measurement the Systolic rate Diastolic rate will be lasting flash on the display for 1 minute 7 4 Storing recalling and erasing measurement data A Storing data After each blood pressure measurement the Systolic rate diastolic rate heart pulse rate and the time amp date of specific day will be automatically stored The memory holds the latest 99 measurement data If more than 99 measurements the memory will automatically clear out the earliest data B Recalling data e Pressing RECALL button at normal time nothing will appear on the display if there is no data in the memory If there is data in the memory the latest recorded set of measurement which are the Systolic rate Diastolic rate heart pulse including the recording time and date will appear and lasting on the display for 1 minute 60 sec e Press RECALL button to read the next line of stored data The data called up on the display is numbered accordingly After reading the recalled data as rotator 99 set of the stored data press RECALL to switch to normal time e To discontinue in the midst of reading of the data press START STOP button to power off C Erasing data e Take out the batteries and then refill 2 pcs batteries again e To discontinue if the data is erased Press RECALL button no data should show up on the screen 8 Maintenance 8 1 Use a piece of cloth with water or mild cleansing agent to wipe the device an
8. ngs the systolic and the diastolic are necessary to enable a physician to evaluate the status of a patient s blood pressure Many factors such as physical activity anxiety or the time of day can influence your blood pressure Blood pressure is typically low in the morning and increases from the afternoon to the evening It is lower in the summer and higher in the winter 1 2 Why is it useful to measure blood pressure at home Having one s blood pressure measured by a doctor in a hospital or a clinic and a group health checks tends to stimulate nervousness in the subject and may even create high blood pressure blood pressure also varies in accordance with a variety of conditions and so judgment is not possible on the basis of a single measurement The blood pressure measured first thing in the morning after getting up before taking any food and with the subject still is known as the fundamental blood pressure In practice it is rather difficult to record the fundamental blood pressure but to come as near as possible to measuring the blood pressure in an environment that is close to this is why it is useful to take the measurement at home Do not move or talk in the midst of taking blood pressure measurement D After the air pressure is increased it will slowly decreased When the pulse rate is detected HEART RATE symbol will start flashing Note If the cuff does not stop inflating remove the cuff at once E After takin
9. obtained Replace all two batteries with new ones Press START STOP button again and re measure Or check cuff if wrapped properly around the wrist according to instructions Check palm if exerting effort Check if there was movement during measurement Check if posture is correct Measuring error symbol Appears all the time till the measurement is completed Note If EP appears on the display just return the device to your local distributor or importer 10 Specifications Model Number TV3649 Method of Measurement Oscillometric Range of Cuff Pressure Range 0 300mmHg Measurement Blood Pressure Range 40 280mmHg Pulse 40 199 beats minute Accuracy Calibration Pressure 3 mmHg Pulse 5 Inflation Automatic inflation Air Pump Deflation of Pressure Automatic air release control valve Exhaust Automatic exhaust valve Display Liquid Crystal Display Unit Dimension 70 x 72 x 29 mm L x Wx H Unit Weight Approx 99 g Sets of Memory 99 set Cuff Size Wrist circumference approx 135 195 mm Operating Conditions 50 F 10 C 104 F 40 C 15 90 RH Storage Transportation 4 F 20 C 158 F 70 C Environment 90 RH Power Supply AAA 1 5 V Alkaline battery x 2 Not Included Battery Life Approx 250 times measurement Accessories Instruction manual carrying case These specications are subject to change without notice for purpose of improvement
10. position A Open battery cover B Refer to the picture in positioning batteries Figure No 5 C All segments will appear on the display in 3 seconds D Display 1month 1 date 12 hour 0 minute 7 2 Setting Date and Time A Press MODE button month starts flashing Press SET button to set the correct month 1 2 3 12 B Press MODE button again date starts flashing Press SET button to set the correct date C Press MODE button again hour starts flashing Press SET button to set the correct hour in 12 hour format D Press MODE button again minute starts flashing Press SET button to set the correct minute 0 1 2 3 59 E Press MODE button again to switch to normal time month date hour and minute appear on the display 7 3 Steps to take blood pressure measurement A Wrap the cuff around the wrist Refer to Wrapping of Wrist cuff as Figure No 6 B Sit upright on the chair to have correct posture Refer to Correct Posture in Taking Blood Pressure as Figure No 7 C Press START STOP button All elements display 888 in 3 seconds Afterward displays the update time The measuring blood pressure symbol will flash on the display and then the air pressure will automatically pump up to 195 mmHg If blood pressure tends to be on the high level the air pressure will automatically increase to the required level for measurement Instruction Manual Wrist Type Blood Pressu
11. r a trained health professional who is familiar with your medical history Using the unit and recording the results regularly for your physician to interpret you will keep your physician informed of the continuing changes in your blood pressure e If you have one of the circulatory problems as arteriosclerosis diabetes liver disease kidney disease severe hypertension peripheral circulation please consult your healthcare professional before using the device e Blood pressure measurements taken with this device are equivalent to those obtained by a trained observer using the cuff stethoscope auscultation method and are within the accuracy limits prescribed by the American National Standard for Electronic or Automated Sphygmomanometers Do not use this manual and product as a substitute for advice diagnosing or treating a health problem or prescribing any medication by your doctor If you have a medical problem promptly consult your healthcare provider Read the Instruction Manual thoroughly before measuring and keep it at hand for your reference at any time 9 Display Messages Troubleshooting Display Condition Cause Corrective action symbol Symbol appears in the Measurements in Pulse symbol measurement condition progress Do not talk and flashes when pulse is detected Battery Appears when the symbol battery voltage is Cx excessively low Appears when the accurate blood pressure could not be
12. re Monitor MODE SET START STOP RECALL Model TV3649 Medical Disclaimer This manual and product are not meant to be a substitute for advice provided by your doctor or other medical professional You are not to use the information contained herein or this product for diagnosing or treating a health problem or prescribing any medication If you have or suspect that you have a medical problem promptly consult your healthcare provider Blood Pressure Monitor Intended Use The device is designed for non invasive measurements and monitoring of adults arterial blood pressure It measures human s systolic blood pressure diastolic blood pressure and heart pulse rate on wrist by oscillometric measurement method The device is recommended for use by people over the age of 18 and is for home use and not clinical use Attention To operate the device properly and get the best result from it please read the Instruction Manual thoroughly before you begin measuring and keep it carefully so that you can access and consult it at any time 1 About Blood Pressure 1 1 What is blood pressure Blood pressure is a measurement of the force of blood flowing against the walls of the arteries Arterial blood pressure is constantly changing during the course of the cardiac cycle The highest pressure in the cycle is called the systolic blood pressure and the lowest is the diastolic blood pressure Both of pressure readi
13. requency range applies NOTE 2 These guidelines may not apply in all situations Electromagnetic propagation is affected by absorption and reflection from structures objects and people ojo Tali jS Manufactured for JOBAR INTERNATIONAL INC Carson CA 90745 Made In China 2012 P N 323102000 VER 001 5 Attaching Pressure Cuff 5 1 Do not place the pressure cuff over a jacket or sweater sleeve Wrap the pressure cuff around the bare wrist with the monitor facing you 5 2 Wrap the cuff snugly Do not make it too tight Fold the remaining part of the cuff back out of the way 5 3 Leave approximately 10 mm Approx 0 4 inch between the cuff and the bottom of your hand palm ae Figure No 6 4 Note e Do not use this device if your wrist has 0 4 10mm any wound or injury iE e Do not wrap the cuff around any body S part other than your wrist 135 195 mm 6 Correct Measurement Position 6 1 To get accurate measurements make sure the cuff is at the same height as the heart Having the cuff higher or lower may cause inaccurate results 6 2 Measurement while sitting down A Place your elbow on a table or other object B Use the armrest to position the arm so that the pressure cuff is at the same height as the heart C Relax your hand with the palm facing up Figure No 7 7 How to Measure 7 1 Inserting batteries in
14. ughout the day and is also affected by many different factors such as smoking alcohol consumption medication and physical activity Normally the blood pressure rises while at work and is at its lowest during sleeping period This device uses the oscillometric method to measure systolic and diastolic blood pressure as well as your pulse rate It is recommended for use by people over the age of 18 and not to be used on children fsi The device is designed for home use and not suitable for clinical use Figure No 2 2 Important information before use of the unit e Do not take a measurement in a low less than 50 F 10 C or high more than 104 F 40 C temperature or you may get the inaccurate readings e Wait 30 45 minutes before measurement if you have just consumed caffeinated beverages or smoked cigarettes e Rest at least 5 10 minutes before taking a measurement e Relax at least 3 5 minutes in between measurements e We recommend you to use the same wrist preferably the left wrist and to measure around the same time each day e Sit down comfortably and place your elbow on the table with your feet at on the floor e Keep the device at heart level Relax your hand with the palm facing up e Perform measurements in a quiet and relaxed environment at room temperature e Do not move or shake the device during a measurement e Blood pressure measurements should be interpreted by a physician o
15. ured field strength in the location in which the device is used exceeds the applicable RF compliance level above the device should be observed to verify normal operation If abnormal performance is observed additional measures may be necessary such as reorienting or relocating the device b Over the frequency range 150 kHz to 80 MHz field strengths should be less than 3 Vim Recommended separation distances between portable and mobile RF communication equipment and the device The device is intended for use in an electromagnetic environment where radiated RF disturbances are under control User can help prevent electromagnetic interference by keeping the device at a minimum distance from portable and mobile RF communications equipment transmitters Below table details the maximum output power of transmitter Rated maximum Separation distance according to frequency of transmitter m output power of 150 kHz to 80 MHz 80 MHz to 800 MHz 800 MHz to 2 5 GHz d 12 P d 12 P d 23 P ae transmitter int Once oi epee ee a ee 23 38 12 For transmitters rated at a maximum output power not listed above the recommended separation distance d in metres m can be estimated using the equation applicable to the frequency of the transmitter where P is the maximum output power rating of the transmitter in watts W according to the transmitter manufacturer NOTE 1 At 80 MHz and 800 MHz the separation distance for the higher f
16. use in all establishments F emissions ASPR 11 including domestic establishments and those directly Jarmonic emissions connected to the public low voltage power supply C 61000 3 2 A network that supplies buildings used for domestic oltage fluctuations Not purposes icker emissions Applicable EC 61000 3 3 3 Device Description 3 1 Name of the parts SETTING BUTTON FUNCTION BUTTON LCD DISPLAY START STOP BUTTON RECALL MEMORY BUTTON WRIST CUFF ALKALINE BATTERY UM 4 AAA 1 5V x 2 NOT INCLUDED Figure No 3 3 2 Description of display symbols MONTH DATE HOUR MINUTE iG d8 18 08 i AFTERNOON TIME e BRE 1t SYSTOLIC RATE MEASUREMENT SYMBOL BLOOD PRESSURE UNIT LOW BATTERY DIASTOLIC RATE ERROR SYMBOL MEMORY NUMBER PULSE RATE Figure No 4 PULSE SYMBOL Inserting Changing Batteries Nhen the low battery symbol CxXh appears on the display lease change the batteries eplace all the batteries with new ones and do not mix new ind old batteries Do not mix alkaline standard carbon zinc or echargeable cadmium batteries either It may shorten the vattery life or cause the device to malfunction emove the battery cover at the side of the unit and insert 2 AA alkaline batteries into the battery compartment as shown Aake sure the polarities and ends are properly positioned Attention I Batteri
Download Pdf Manuals
Related Search