OPERATING INSTRUCTIONS
Contents
1. 8 Fire Panel Opto Isolated Inputs 8 Analogue Inputs Open Collector Outputs amp RS485 Ports 8 Commissioning Power Up Procedure System Configuration Disassembly Main Cover Removal BVSMP Power Supply or Amplifier Removal 2 Eclipse2 issue iii VIGIL Eclipse2 Installation Instructions Eclipse2 issue Eclipse2 issue VIGIL Eclipse2 Installation Instructions AMENDMENT RECORD Page Number s Change Note Nature of Date of Affected Number Amendment Amendment PROPRIETARY NOTICE All data and information contained within this manual is of a proprietary nature with the exclusive title to the same held by Baldwin Boxall Communications Limited The possession of this manual and the use of the information is therefore restricted only to those persons duly authorised by Baldwin Boxall Communications Limited Do not reproduce transcribe store in a retrieval system or translate into any language any part of this manual without the prior permission of Baldwin Boxall Communications Limited In the interest of continual product development Baldwin Boxall Communications Limited reserves the right to make changes to product specification without notice or liability Use of Baldwin Boxall Communications Limited products as critical components in life support systems is not authorised except with express written approval from Baldwin Boxall Communications L2. BALD VIGIL Eclipse2 Installation Instructions Manual name Eclipse2 Issue ECR 2053 Date of issue January 2007 VIGIL Eclipse2 Installation Instructions CE January 2007 Baldwin Boxall Communications Limited Wealden Industrial Estate Farningham Road Jarvis Brook Crowborough East Sussex TN6 2JR UK Telephone 44 0 1892 664422 Facsimile 44 0 1892 663146 Email mail baldwinboxall co uk Website http www baldwinboxall co uk This equipment has been designed and manufactured to conform to the following EC Standards EMC EN55103 1 Environment Classification El EMC EN55103 2 Environment Classification E5 Safety EN60065 Failure to use the equipment in the manner described in the product literature will invalidate the conformity A Declaration of Conformity statement to the above standards and a list of auxiliary equipment used for compliance verification is available on request Eclipse2 issue BALDWIN MM CO BOXALL VIGIL Eclipse2 N S UNICA TION Installation Instructions Amendment Record yV Proprietary Notice v Safety Information vi Comments vi Introduction VIGIL Eclipse2 Description Front Panel Controls amp Settings Termination Details 3 Installation VIGIL Eclipse2 Dimensions 5 Hole Centres For Mounting Holes Connections to Site Wiring Microphone s Installation 8 Loudspeaker Line Connections
3. addressed to mail baldwinboxall co uk vi Eclipse2 issue OXALL VIGIL Eclipse2 C S Installation Instructions Introduction I 1 VIGIL ECLIPSE2 DESCRIPTION The VIGIL Eclipse2 is a purpose built wall mountable Voice Alarm or Public Address system It boasts simple design that enables straightforward installation and commissioning The VIGIL Eclipse2 uses a VIGIL BVRD2M DSP Router along with VIGIL Amplifiers and BVSMP Power Supply to achieve up to either seven single or four dual circuit zones The unit can accept upto seven line inputs and can store upto six pre recorded messages The VIGIL Eclipse2 can be either used as a stand alone system or it can be part of a decentralised network of upto 128 units All site wiring connections are made to a single easily accessible Termination Board mounted at the top of the unit The system is powered by a 230V AC 50 60Hz power supply with internal battery backup The VIGIL Eclipse2 is supplied with the necessary number of BEL1 end of line monitoring units to provide full Loudspeaker monitoring The unit is fully configurable via a PC using the USB interface and the Configuration Software Eclipse2 issue VIGIL Eclipse2 BALD IN Installation Instructions C BOXALL UNICATIONS 1 2 FRONT PANEL CONTROLS amp SETTINGS Figure 1 1 VIGIL Eclipse2 Front Panel Re e sl 4 Pia pi b 7 4 E j RI wt 4 J FAULT FAULT LAMP SELEC
4. NdINO INIT ADDL 7 103 JL4 l 0140 J 103 _ 94 1 01d0 103 _ Sd l 01d0 103 _lhd l 0140 7 103 _Jed i 0140 Input EoL Resistors 103 24 1 01d0 7 103 1d l 01d0 Fire Panel Opto 103 M3 ldo SID KOT OV KON OD KO GS AASIN CS AANS VALORI Bs IYI WW YE OAI NY V YNY OW E 9S ING CAN BUS ADDRESS AY L gt T RS485 Ports 1 amp 2 JOC Fault Contacts D k gt l al a S o 5 2 MINI MV oon T W a AMI L NANI AK JOW A YAARA 900 SINdINO LI r xny Le A oiany ji DI Y CV FIOS a S AAAA Open Collector Outputs dd gt OW YW d ony td VE ING a Ning YE NOOR AC LIN 2 ao sa w nel a z 2 ROG Seseae A IIC Audio Inputs SION OLN 7 AOAN LL a a gt oa 2 N e a eee n a E i r Q O d 3 300 ZNJ 3 OSADA a ARIA An wmoo Tang dn ma 92 a NS OD QV OM DAnanke 9A Ii ISS 1 DO VA w 8 to D lt fre A QE Ow S z Ss gt A O NI c a m a L NA NA NOTE Each unit is confi gured for the requirements of the installation i e unused inputs amp outputs etc may not be connected internally Eclipse2 issue 7 VIGIL Eclipse2 BALDWIN MM Installation Ins
5. T BACK ACCEPT RESET TEST USB CONTRAST com FAULT i 9 Wr DSPOK proc G dra SELLA ATTI ZITTA LITTA ae RI ZII A Access Control System Configuration configuration options is not available to prevent Unless Key is turned and password entered access to Key Switch unauthorised or accidental changes to system setup 40 x 2 Character LCD Shows either the current system status or if in Fenty Cotten noe oo and mens ole __ C Multi Function Encoder Used for changing values and entering text when in SASS eee TT Left navigation Press to move left through available menus and options ii Right navigation Press to move right through available menus and options ice F Select navigation Press to choose the currently selected option a e G Back navigation Press to move back to the previous menu iii CHE Fault Accept button Press to accept a fault and silence the buzzer Li Reset button Press to reset a displayed fault Note only available if key switch is turned J Lamp Test button Test button Press to check LEDs and sounder to check LEDs and sounder ae oe LEDs No faults detected Com Fault Fault detected shown on LCD Display Proc Fault Processor or Internal Comms fault detected Potentially Fail Safe operation only available hard wired All Call on Mic amp 2 and EM message will operate correctly DSP OK flashes to indicate DSP has no faults DL USB port c
6. er Extrusion screws as shown in Figure 4 4 and detach the upper extrusion Figure 4 4 Upper Extrusion Screws Upper Extrusion Securing Screws Eclipse2 issue 13 VIGIL Eclipse2 BALDWIN MM Installation Instructions CO Each module is held in place by two locating pins that pass through the rear panel as shown in Figure 4 5 Figure 4 5 Module Locating Pins BVSMP amp Amplifier Locating pins Carefully lift the module off the locating pins and remove it from the Power Tray 14 Eclipse2 issue
7. ets Lift the cover clear of the chassis and store in a safe place WARNING Removing the cover allows access to potentially dangerous voltages If Functional Testing Maintenance or Repair is to be completed with the Mains Power and or battery backup connected then this should only be undertaken by personnel who are fully aware of the danger involved and who have taken adequate precautions and training 4 2 BVSMP POWER SUPPLY OR AMPLIFIER REMOVAL Remove the main cover as described in Section 4 1 WARNING Ensure the Mains Power and Battery Backup are isolated before disconnecting a BVSMP Power Supply module or Amplifer module Access to the BVSMP Power Supply Module and the Amplifier Module s is achieved using a front opening Power Tray Figure 4 2 Power Tray Securing Screws a tei TTE 2 off M6x10 Power Tray securing screws 12 Eclipse2 issue OXALL VIGIL Eclipse2 CA S Installation Instructions Carefully release the two securing screws to allow the Power Tray to pivot forward CAUTION Hold the Power Tray in place when removing the screws as it will attempt to pivot forward when the screws are released as shown in Figure 4 3 The Tray will pivot approx 30 to allow access WARNING Do not loosen or remove any other screws to access the Power Tray Figure 4 3 View of Open Power Tray Disconnect all cables attached to the required module Remove the 4 off Upp
8. imited VIGIL Eclipse2 BALDWIN M M Installation Instructions CO SAFETY INFORMATION Personnel who install maintain or repair this equipment must read the safety information below before starting work Voltages in excess of 30 Volts RMS or 50 Volts DC are considered Hazardous and in certain circumstances can be lethal If Functional Testing Maintenance or Repair is to be completed with the Mains Power and or battery backup connected then this should only be undertaken by personnel who are fully aware of the danger involved and who have taken adequate precautions and training This Manual contains Warnings Cautions and Notes Warnings describe potential threats to health or life e g WARNING Before attempting to remove this component ensure the Mains Power Supply and Battery Backup have been disconnected Cautions describe potential threats to the equipment e g CAUTION Notice must be taken of all cautions If a Caution is ignored the equipment may be damaged CAUTION ELECTRO STATIC SENSITIVE DEVICES Observe the relevant precautions for the protection of Electro static Sensitive Devices when handling this equipment Notes are statements that are useful to the user in the context of a particular section of the manual e g NOTE Do not speak into the microphone until the Speak Now LED is IN illuminated COMMENTS Comments regarding the content of this manual are welcome and should be
9. onnection Connection for Configuration Software 2 Eclipse2 issue OXALL VIGIL Eclipse CA S Installation Instructions 1 3 TERMINATION DETAILS All terminations are made ona single PCB mounted at the top of the unit Figure 1 2 Typical VIGIL Eclipse2 Termination PCB aa To aid installation the Termination Board includes the relevant Audio and Control Inputs from the BVRD2M to make them more accessible The Termination Board is also a CANBUS expansion module that adds features in addition to those available on the BVRD2M The total number of control inputs available on the VIGIL Eclipse2 is as follows 8 x Opto coupled Control Inputs 16 x Analogue Control Inputs e 3x RS 485 ports 8x Amplifier Loudspeaker line monitored outputs for upto 4 dual circuits no reserve 7 single circuits no reserve or 6 single zones if reserve amplifier auto changeover is used Eclipse2 issue 3 VIGIL Eclipse2 Installation Instructions Eclipse2 issue Eclipse2 issue 2 1 2 VIGIL Eclipse2 Installation Instructions Installation WARNING The VIGIL Eclipse2 can weigh upto 65Kg including batteries Ensure the mounting wall is strong enough to support the unit CAUTION This unit must be installed in a well ventilated area and cannot be floor mounted or positioned where any of the ventilation grills would be blocked or obscured CAUTION There are 14 gland positions on
10. se2 N S Installation Instructions 3 Commissioning 3 1 POWER UP PROCEDURE Ensure the Mains Supply is isolated Remove the battery fuses located on the Left Hand Side of the chassis Install the batteries and connect the battery cables including the link lead between them but DO NOT re fit the battery fuses Connect Mains Power Press the FAULT ACCEPT button to accept any faults that are displayed on the front panel and silence the fault buzzer Carefully fit the battery fuses and replace the plastic cover over the fusebox 3 2 SYSTEM CONFIGURATION The VIGIL Eclipse2 will have been assembled and tested in accordance with the System Schematic To modify the configuration or system settings refer to either the BVRD2M Manual or the Help in the Configuration Software Eclipse2 issue 9 VIGIL Eclipse2 Installation Instructions 10 Eclipse2 issue OXALL VIGIL Eclipse2 CA S Installation Instructions 4 Disassembly 4 1 MAIN COVER REMOVAL The main cover is secured by two M6 x 16mm screws as shown in Figure 4 1 Figure 4 1 Main Cover Securing Screws M6 x 16 Cover VIGIL Eclipse2 with Securing Screws Cover Removed Eclipse2 issue Il VIGIL Eclipse2 BALDWIN MM BOXALL Installation Instructions CO NICA S UNI TION To remove the cover loosen the screws shown in Figure 4 1 and then lift the cover until the two locating pins in the top surface clear the mounting gromm
11. the top edge of the unit for terminating site cabling Do not attempt to add cable glands through the base of the unit since they will prevent the installation of the batteries VIGIL ECLIPSE2 DIMENSIONS Table 2 1 VIGIL Eclipse2 Upto 65Kg including batteries VIGIL Eclipse2 BALD IN Installation Instructions C BOXALL UNICATIONS 2 2 HOLE CENTRES FOR MOUNTING HOLES Figure 2 1 Mounting Hole Centres and Cable Gland locations a nw eon oO oo 2 o LO n NODO CLIN N ee ee I O O se oh al There are 6 off 8mm mounting holes which should all be used to distribute the weight of the unit Batteries should not be fitted until the unit is secured to the wall 6 Eclipse2 issue BALDWIN MM BOXALL VIGIL Eclipse2 Co NIC S UNICATION Installation Instructions 2 3 CONNECTIONS TO SITE WIRING Connections to the Termination PCB should be made in accordance with the System Schematic supplied Figure 2 2 Termination PCB Connections SHOCK DANGER RISK OF ELECTRIC RISK OF ELECTRIC SHOCK 230V Mains DANGER SINdINO INIT AOOL 2 TRIC SHOCK ELEC Fire Panel Opto Inputs RS485 d Port 3 DOSAO OVSEGSODVEO0S ay gt E a o DANGER RISK OF IONI Oo I00V Line Outputs Ra SHOCK Jeod 90006 gt I 14 0 DANGER RISK OF ELECTRIC A HE 1d 0 Ta SI
12. tructions 2 3 1 Microphone s Installation Connect suitable i e fire resistant cable from the microphone s to the termination PCB in accordance with the System Schematic supplied Refer to the relevant Instruction Manuals for connection details of each specific Microphone type NOTE When using Fire Microphones e g BFMO1 04 etc ensure any cs unused Zone Select Outputs are linked to 4 VE REF on the terminal block inside the microphone case This prevents incorrect fault indications 2 3 2 Loudspeaker Line Connections Ensure all loudspeaker connections are made according to the System Schematic supplied Ensure suitable cable for the installation is used This includes adequate power rating and for VA installations the cable must be fire resistant When BEL1 End of Line Surveillance modules are used the Earth Return from each BEL1 must be connected to earth terminal block mounted on the chassis 2 3 3 Fire Panel Opto lsolated Inputs Connect the Fire Panel sounder circuit s to the relevant Opto Isolated Inputs using suitable fire resistant cable and ensure the polarity A B is correct Fit correct value End Of Line resistors to the relevant Terminal Blocks 2 3 4 Analogue Inputs Open Collector Outputs amp RS485 Ports Ensure all Analogue Inputs Open Collector Outputs and RS485 Port connections are made according to the System Schematic supplied 8 Eclipse2 issue BOXALL VIGIL Eclip
Download Pdf Manuals
Related Search