INSTALLATION and OPERATING INSTRUCTIONS
Contents
1. ARITERM ARITERM SWEDEN AB Installation Instructions 2011 09 22 3 20 H PELLET STOVE KMP LILLA FRO Care and maintenance summary We recommend that you follow the care and maintenance instructions in order to obtain the best possible results from your stove e The stove needs air in order to function never close the supply air vent to the house This is not an issue for those who chose a solution with KMP Draft this ensures that the stove has air e Your engineer has adjusted the amount of fuel used in the stoves starting dose Use the menu system to change the starting dose and output see section 1 6 in the manual e We recommend removing the ash daily during the firing season or each time pellets are filled Remove ash through the door using the handle supplied Lift out the burner from the burner housing and remove any ash from the ash box unburned pellets must not be emptied into the ash box there is a risk of them starting to smoulder e After a period of use the glass in the door becomes coated with soot and eventually becomes opaque Therefore it should be cleaned on the inside using kitchen roll moistened with normal tap water We recommend that this is done every time the pellet hopper is refilled Wait until the glass has cooled before you start cleaning e Vacuum the ash from the ash box once between visits from the chimney sweep which is normally twi2. QU lt 430 gt A V E 2 076 A 2 LO N N v x ARITERM H 1 4 Control panel The control panel has a display and adjustment dial see fig 3 The display shows the operating mode and the current temperature Explanatory text scrolls through the display every 5 seconds The adjustment dial is used by pressing or turning Turn it to scroll through the menu or change the value when adjusting Pushing once makes a selection in the menu To ignore the change wait 4 seconds and the value is reset Example Power the stove Pressing once causes the panel to ask Start Pressing again means that you confirm the question and the stove starts If you turn one increment clockwise instead you jump in the main menu and come to Stop T Usermenu and Back Stop T You set the desired stop temperature here Usermenu The other time and temperature settings are adjusted here To make more advanced settings one must have code SetCode The stove is started by pressing the control panel dial and confirming Start by pressing again Take care not to start the stove when there are flammable objects above or immediately adjacent To shut off press the control panel dial and confirm Stop by pressing once Other menu steps are shown in section 1 6 Fig 3 ARITERM SWEDEN AB Installation Instructi
3. 10 Installation POSITIOTIIDIO dens odere Burn rds er Reb oe 11 qu oh ate Poe a ae a w PRS RA nA 11 Ventilation ge Uae Da ee xS pe S 11 KNIPIDEIdbt Zu eser reris a EF Bea eae a8 i 11 Electrical 12 Documentati0N eee 12 Operation and maintenance UCN TL 13 ASH re Mmo N all uui hme chiens ewe ERE Is 13 GIGSS ee vr 13 SWEEPING Ls acto eg aee ede duo ahd eae 14 snd bac to Bon ese dara apes s Een eed Ba wer 14 Operating stoppage 22 chase kde upaqa Ss 14 Fault tracing and remedy 15 Dismantling e vend A chante as set um 17 Firirig elemerit uu as aaea tothe kaspa ptem a 17 Combustion 17 Fame detector iue 20538 2282222286 tae a a 17 TOMA rali Lam nk 18 Coritrol circuit DOard easg 22 te be RE ave 18 Hu LP 18 Temperature sensors and safety switches 18 Warranty Darts xu i Dan skal m ato eg ede dd 18 ARITERM B 1 Product description H 1 1 General The Lilla Fr stove has been developed to work as a primary heat source The stove s high level of efficiency in combination with automatic operation means that the stove replaces up to 80 96 of the heating in a normal family house with electricity as heating source The stove is designed for firing with wood pellets and requires an e
4. H 3 4 Sweeping The chimney must be swept twice a year The flue and its connection and the area underneath the cleaning hatch must be cleaned at least once between the chimney sweep visits Open the top panel 2 Unscrew the knob that locks the ash box 3 Lift the ash box vertically by both knobs 4 Vacuum clean the ash from the ash box 5 Vacuum the horizontal flue all the way to the chimney The hole is 50 mm in diameter sufficiently large for a normal vacuum cleaner hose If the flue Drag is installed the sweeping can be done from the outside 6 Make sure that the ash hatch is firmly in place after cleaning and tighten the knob properly ARITERM The chimney must be checked for blockages if unused for a prolonged period H 3 5 Hot air fan Vacuum cleaning of the fans with a brush nozzle should be carried out a couple of times annually after removing the side hatch Do not forget to pull the plug out before the side hatch is removed 1 Open the top panel 2 Loosen the screw on the top of the side panel 3 Snap the back of the side panel from the stove s back plate by prizing back the top and bottom corners of the side panel 4 Unhook the panel out forwards NOTE When vacuuming the hot air fan be careful not to damage the long and vulnerable fan blades The fan bearings can start to whistle after operating for some time in a dusty environment Rectify this with a drop of oil on both b
5. If no flame can be detected the exclamation mark illuminates and the stove goes into Operational stoppage mode Maximum time for firing element Approx 6min Hot air fan on The flame symbol is displayed as e If the flame sensor indicates n long as the flame sensor indicates flame the firing element is shut aflame off the flame symbol illuminates and the firing element symbol goes out Approx 8 min e The feeder on at low output Runs from 1 8 6 seconds every 10th second Approx 10 min Operating phase The thermostat regulates the output according to the set values High output operat ion After Start High output scrolls through the display The feed runs from 3 10 seconds every 10th second Combustion fan Fan HI The time depends on the set fuel amount at high output Every 10 seconds Set temperature and room temperature are compared The flame sensor is checked If the room temperature exceeds the set temperature the stove switches to low output Not if Stop T is On If no flame can be detected the exclamation mark illuminates and the stove goes into Operational stoppage mode Stop 0 secs The feeder stops Combustion fan runs at max To blow ash out of the burner ibl The hot air fan runs 4 min Combustion fan stops The hot air fan stops ARITERM SWEDEN AB Installation Instructi
6. 4 Dismantling H 4 1 Burner 1 Z 3 Open the door and remove the ash box Remove the four screws holding the burner flange to the stove wall fig 10 Pull the burner straight out until the cables connecting the burner to the control circuit board are visible Squeeze the locking catches together and pull the two connectors apart The burner can now be removed Reinstall in reverse order 4 2 Firing element Remove the burner as above Remove the four screws 1 holding the upper part of the ignition bracket The firing element is now free 3 Disconnect the firing element s cables from the triac control and the terminal block WN N A WN JH Loosen the screw 3 that secures the firing sleeve Remove the firing sleeve from the element Pull out the cables from the lead ins Reinstall in reverse order 4 3 Combustion fan Remove the burner and the ignition console according to the Firing element section Remove the red and the blue cable from the terminal block on the side of the bracket Remove the screws 2 holding the fan to the bracket Reinstall in reverse order 4 4 Flame detector Remove the burner and the ignition console according to the Firing element section Remove the cables from the terminal block in the side of the bracket Remove the flame sensor but first note how it sits at the side of the bracket Reinstall in reverse order The flame sensor must stick in a
7. B len gray brown o Power Supply ac PWM Out option option e p Ae H 2 6 Documentation e 9 9 Fuses 2x 3 15 AT The stove must be installed inspected and commissioned by an authorised engineer At installation the following data must be collected and gathered under the section Warranty and Installation proof Safety switches grey 82 Convector fan e Manufacturing number 2 Installation date 5 e Vacuum chimney cold 5 white e Vacuum in chimney hot white Feeder motor Outdoor temperature e Smoke gas temp at max operation e Carbon dioxide content CO Fig 8 e Distance to combustible material ARITERM SWEDEN AB Installation Instructions 2011 09 22 12 20 H PELLET STOVE KMP LILLA FRO H 3 Operation and maintenance The K6 stove is designed for a long service life motors and other moving parts are of a very high quality All bearings are lifetime lubricated and the only preventative maintenance that is normally required is sweeping and cleaning H 3 1 Fuel The K6 stove functions best with 6 or 8 mm wood pellets max length 40 mm The pellets are supplied in plastic sacks that can be stacked on pallets or other suitable surfaces Avoid exposing the sacks to moisture or mechanical stresses vibrations or blows Careless handling of pellets can easily reduce the fuel to sawdust The sawdust is
8. fed into the burner with the pellets but can cause poor combustion Fill the hopper with pellets slowly and without too great a drop The feeder completely empties the hopper and therefore does not normally require cleaning The hopper is filled by opening the hatch above the pellet magazine Unlock by turning the locking knob a 1 4 turn clockwise The hopper can be filled while the stove is running but because the feeder switches off when the hatches are opened you only have a few minutes before the hatch must be locked again If the hatch is open for longer the flame is likely to get so low that the stove will switch itself off after which it must be restarted again after the switch is set to the OFF position The stove is started by moving the switch to the ON or THERMOSTAT positions Take care not to start the stove with flammable objects on top of or in the immediate vicinity of the stove Shut off is carried out by moving the switch to the OFF position The stove must not be covered ARITERM H 3 2 Ash removal The amount of ash that build up in the burner varies depending partially on how the stove is fired number of starts and stops division between full and half speed and partially on the quality of the pellets The ash content varies between different pellets but can also differ between different batches from the same factory This can only be established through trial and error but generally
9. 47 AR ITE M INSTALLATION and OPERATING INSTRUCTIONS PELLET STOVE LILLA FRO For a sustainable future H PELLET STOVE KMP LILLA FRO ARITERM SWEDEN AB Installation Instructions 2011 09 22 2 20 H PELLET STOVE KMP LILLA FRO B Unpacking Remove the wood packaging Detach the side panels and install the feet as follows Loosen the screw on the top of the side panel Lift the side panel straight up Unhook the side panel by carefully prying with a screwdriver and at the same time pull the panel out forwards Also unhook the panel at the lower edge by pulling the panel out forwards Detach the side panel from the back panel by lifting it straight back and slacken off the two wooden screws that hold the stove to the pallet Repeat 1 6 on the other side Lean the stove to the side so the two adjustable feet can be threaded in as illustrated Screw them in until they just reach through the plate Lock in place with counter nuts on the underneath Repeat on the other side Lift the stove down off the pallet Take hold of the stove s bottom plate Do not lift by the back plate or the magazine Connect the control panel s control cable if this is not already in place Reinstall the side panels in reverse order according to6 1 Place the stove in its final location and connect it to the flue Adjust the height using the feet if necessary
10. ce a year The ash hatch is located behind the filler hatch and it can be lifted straight up after the plastic knob has been screwed loose e The stove s tubes are swept automatically using the sweeping unit patent pending every time the hatch is opened and they normally do not need any further sweeping e Vacuum the interior of the stove once a year to prevent the stove s fans from becoming jammed by the soot that gets into the stove To access the fan first pull out the plug then remove one of the stove sides If you have installed KMP Draft ash must be removed from it at least once every firing season NOTE When you start your stove for the first time there may be a slight smell of paint this is because the paint on the stove body must cure fully before one can obtain odour free operation ARITERM ARITERM SWEDEN AB Installation Instructions 2011 09 22 4 20 ll PELLET STOVE KMP LILLA FRO B Table of Contents 1 1 1 2 1 3 1 4 1 5 1 6 1 6 2 1 2 2 2 3 2 4 2 5 2 6 34 3 2 3 3 3 4 3 5 3 6 3 6 4 1 4 2 4 3 4 4 4 5 4 6 4 7 4 8 Product description GENET al ER tee fo ud aa 5 Components ziv epee Pag erp ass Eu EUER 6 Technical data cesses tae higie dx semua 7 Controlpane 7 8 Safety system ao o UR n s argen 9 Control system settings 9 Coritrol d ration uas 024808 22024
11. e pellet hopper 17 is filled through the filler hatch 18 The hatch is locked with a knob The pellet feeder 19 sits in the bottom of the pellet hopper and it consists of a slowly rotating screw The patented design means that pellets cannot stick in the feeder Safety thermostats 20 are mounted on the pellet hoppers right side trip at 85 C and the ash box trips at 204 C The stove must not be modified and only spare parts recommended by the manufacturer may be used Fig 1 SR ARITERM ARITERM SWEDEN AB Installation Instructions 2011 09 22 6 20 H PELLET STOVE KMP LILLA FRO 1 3 Technical data Heating output HI approx 5 3 kW Pellet hoppet ueteri tn ipee 30 litres approx 20 kg Efficiency level HI approx 92 9496 CO MY LO toc te approx 300 300 ppm Smoke temperature lt 180 120 C Aly eto eer tere sette 3 2 2 4 g s Temperature range thermostat approx 10 30 C bsec 75 kg Electrical CortiGCllon ect tte eee 230 V 50 Hz Electrical output firing 450 W Electrical output 20W incomes wood pellets 26 or 8 mm EN 14961 Depending on fuel density
12. earings H 3 6 Operating stoppage If the stove does not start check first where the fault is located using the fault tracing diagram below If you consider that you have the necessary expertise rectify the fault as suggested If not or if the fault cannot be located contact your dealer After an unsuccessful start attempt or operating stoppage the burner crucible must always be emptied If there are unburned pellets in the crucible it must not be emptied into the ash box ARITERM SWEDEN AB Installation Instructions 2011 09 22 14 20 H PELLET STOVE KMP LILLA FRO H 3 6 1 Fault tracing and remedy ARITERM Fault Cause Action Fault Cause Action The stove does not start green LED does not light The cable is not connected No voltage at the socket Stove fuse blown The cable between the control panel and the control circuit board is not correctly con nected The stove is in the cooling phase Connect to earthed 230 V socket Check the fuse Change the fuse Remove one side hatch and check that the cable is connected to the card device Check the same thing on the rear of the control panel Wait until the fans have stopped Pellets do not ignite no smoke The firing element does not work Bad connection Starting dose too small Replace firing element Check wiring and connections Adjust the fuel volume The stove does not
13. en replacing the fuses pull the connector cover straight out to access the fuses Fig 11 4 8 Temperature sensor and fused switch This work must be carried out by an authorised engineer 5 Warranty ARITERM For warranty issues Ariterm Sweden AB refers to our local Distributor Fig 11 ARITERM SWEDEN AB Installation Instructions 2011 09 22 18 20 H PELLET STOVE KMP LILLA FRO EID ARITERM SWEDEN AB Installation Instructions 2011 09 22 19 20 If these instructions are not followed at installation operation and maintenance Ariterm Sweden AB s applicable warranties are not binding Ariterm reserves the right to make changes to components and specifications without prior notice Ariterm Sweden AB Flottiljvagen 15 SE 392 41 Kalmar www ariterm se
14. et here Default All the values are reset to factory settings here Back Press for Usermenu Ny Firing element Indicated Activated Feeder motor Combustion fan Fault function Stove Activated Activated Indicated in operation ARITERM SWEDEN AB Installation Instructions 2011 09 22 9 20 H PELLET STOVE KMP LILLA FRO H 1 6 1 control process Otherwise the electronics manage all processes as follows ARITERM Start Low output operation deactivated from the factory Time Events Comments Time Events Comments 0 secs Firing element on After Start Low output scrolls through the The time depends on the set The firing element symbol illuminates display pellet amount at low output The feed runs from 1 8 6 seconds 120 secs The motor symbol illuminates The feeder starts 220 330 secs The feeder stops Starter dose The combustion fans starts puls ing and stops twice The motor symbol goes out The time depends on the set pellet amount at ignition Pellet level should be approx 5 mm above the firing element hole every 10th second Combustion fan Fan LO Every 10 seconds Set temperature and room temperature are compared The flame sensor is checked If the room temperature exceeds the set temperature by more than 2 C the stove goes to stop and then standby mode Standby scrolls through the display
15. f the flue including insulation and surrounding shaft may be 100 C when the stove is running at full output The surface temperature of adjacent building parts may not exceed 80 C e Minimum diameter round duct or side rectangular duct should be 80 mm The smoke ducts must be made of non flammable material of sufficient durability and with sufficient resistance to temperature variations climate effects corrosive smoke gases and slag and use of sweeping tools etc e t must be possible to clean the flue If fallen ash cannot be removed via the stove s cleaning hatch another cleaning hatch must be arranged The cleaning hatch must not be located in a room other than the one in which the stove is located e Connection to the chimney must be via a steel flue pipe of at least 2 mm thickness or minimum 1 mm thickness if stainless steel The joint is sealed with hard packed glass fibre or elastic sealing compound that can tolerate at least 250 C All parts of the chimney situated outdoors must be insulated e The stove must NOT be connected to divided chimneys or flue gas ducts The smoke gases contain water vapour that can condense to water if the temperature is sufficiently low approx 55 C which can cause damage both to the chimney and stove If the temperature approx 1 m below the chimney top is below 60 C one should install an insert speak to your engineer or chimney sweep In the event of a chimney fire pull out the plug and ca
16. ing the front edge Under this are the ash hatch 2 and the filler hatch 17 for the pellet hopper The front 5 is opened to reach the door 7 The door is unlocked with the enclosed handle and it opens forwards towards the floor The burner housing 8 is located in the hearth and is accessible when the door has been opened It is installed with four screws on the rear of the stove body The burner 9 sits loose in the burner housing The firing element 10 is located in the burner housing behind the burner The firing element gives off the heat required to ignite the fuel The flame sensor 11 is beside the ignition unit and indicates whether there is flame in the burner The ash box 12 is inserted in the bottom of the hearth under the burner housing It can be removed when the door has been opened The combustion fan 13 is placed on the rear of the burner housing and provides the burner with air for combustion If the stove is connected to the flue Drag the fan is replaced by a hose which is connected to the wall lead in The control circuit board 15 is placed inside the stove and it is powered by an electronic transformer that supplies 12V voltage to the electronics and control and sensors The hot air fan 16 is located inside the stove and sucks air from the rear of the stove which is then heated up in the combustion chamber and smoke tubes 4 and expelled through holes partly in the back plate and partly in the front Th
17. is properly closed A weak clicking noise must be heard when closed Fill up the pellets Remove pellets from the chute Ensure that there are no foreign objects in the chute Check that there are no foreign objects stuck in the feeder auger Check switches and wiring to the motor Replace motor See Menu ErrorHI The flame sensor has not detected a flame during high output Incorrectly adjusted fuel and or air amount FeedHI or Fan HI The hopper is empty Pellets have jammed in the feeder The feeder auger does not rotate See Menu Fill up the pellets Remove pellets from the chute Ensure that there are no foreign objects in the chute Check that there are no foreign objects stuck in the feeder auger Check switches and wiring to the motor Replace motor ErrorLO The flame sensor has not detected a flame during low output Incorrectly adjusted fuel and or air amount FeedLO or Fan LO The hopper is empty Pellets have jammed in the feeder The feeder auger does not rotate See Menu Fill up the pellets Remove pellets from the chute Ensure that there are no foreign objects in the chute Check that there are no foreign objects stuck in the feeder auger Check switches and wiring to the motor Replace motor ARITERM SWEDEN AB Installation Instructions 2011 09 22 16 20 H PELLET STOVE KMP LILLA FRO H
18. lectrical power supply In event of a power cut the stove requires a reserve power source from an uninterruptible power supply UPS or a petrol driven generator in order to function The integrated convection fan distributes the hot air around the house for best effect the stove should be centrally located on the lower floor of the house The room temperature is easily set from the control panel During thermostat operation the stove automatically ignites and extinguishes the stove when the set temperature is reached is filled with pellets by opening the hatch under the stove s top panel The spacious hopper means that the stove only needs to be refilled a maximum of twice a day The filler hatches and door are equipped with safety switches Two safety thermostats are mounted together with the switches in a safety coil to prevent overheating and back fire Lilla Fr can be installed without a traditional chimney if your home does not have one The solution that makes this possible is called KMP Drag which is a patent pending fan controlled flue gas duct that goes straight out through the wall The stove must not be used as an incinerator and must only be fired using wood pellets acc to EN 14961 NOTE The stove s surfaces on and around the glass become extremely hot ARITERM SWEDEN AB Installation Instructions 2011 09 22 5 20 H PELLET STOVE KMP LILLA FRO H 1 2 Components The top panel 1 is opened by lift
19. ll the emergency services B 2 3 Ventilation There must be at least one air supply ventilator in the room where the stove is located If there are other exhaust fans increase the number of supply ventilators until the fans no longer affect the pressure ratio We also recommend that a chimney fan is installed H 2 4 KMP Draft Information about installation with KMP Draft instead of a traditional chimney is available in a separate manual See Draft Wall fan Installation and Operation instructions ARITERM SWEDEN AB Installation Instructions 2011 09 22 11 20 PELLET STOVE KMP LILLA FRO AEn 2 5 Electrical connection The back of the stove is equipped with a white black 1 5 m long cable with plug which must Er m 0 Light sensor be connected to a 230 V 50 Hz earthed red red red mains supply The internal wiring diagram plack a EE BR Combustion fan laci is shown in fig 8 NOTE f the connection cable is damaged orange em Ignition element it must be replaced by one of the same orange type contact the dealer red white Ignition unit Remote option V 2000 ud Senor orange O V 0VDC option black yellow green enr brown ro To SMS o blue H NEI rue Bs black O N
20. ned the fuel feed is interrupted and a warning text is shown on the display 3 Two thermostats are located as shown in section 1 2 Components fig 1 If the maximum permitted temperature is exceeded the feeder stops the stove switches itself off and the display shows Operational stoppage The alarm must be confirmed by pressing a button Do not forget to rectify the cause of the operational stoppage 4 A flame sensor is located in the burner fig 1 If the flame goes out or pellets are fed in faster than they can be burnt and no flame is indicated for approx 3 5 minutes the stove switches itself off and an exclamation mark illuminates while operational stop page scrolls through the display 5 The door is equipped with a safety switch The door must be closed during operation if it is opened the fuel feed is interrupted The safety switches are tested by unlocking the filler hatch during use or start up The pellet feeder should then stop H 1 6 Control system settings The settings are made in the control panel in a menu system Before entering the menu the panel is in display mode Enter the menu by pressing the dial If the menu is inactive for a long time the panel returns to display mode The menu system consists of a main menu and several sub menus Usermenu and Settings Turn the dial to scroll through the menu To jump out of the menu hold the button in for 4 seconds The menu appears as follows Main menu Sta
21. ons 2011 09 22 10 20 H PELLET STOVE KMP LILLA FRO H 2 Installation H 2 1 Positioning The installation must meet all applicable European standards local and national requirements The stove should be located in a central position on the lower floor of the house to facili tate heat spread Consideration must be made of how the chimney is arranged contact the dealer Try to avoid placing it in a corner but if it cannot be avoided observe the minimum distances to the walls according to fig 7 The Building regulations contain a number of regulations to prevent fires Generally speaking the regulations are applied if the following is being observed e The stove must be placed at least 100 mm from the wall e The underlay must be made of non flammable material and extend at least 300 mm to the front and 100 mm to the side of the stove If the hearth surface is made of steel it must be at least 0 7 mm thick e Flammable material must not be exposed to temperatures exceeding 80 C Otherwise the stove must have at least 1 m free space on one side in order to allow service The weight of the stove is so low that no extra demands are made on the joists etc i N C M 2 Fig 7 Toc ARITERM 2 2 Chimney The regulations regarding chimneys can be found in the Building regulations The most important regulations are e The highest surface temperature o
22. ons 2011 09 22 7 20 H PELLET STOVE KMP LILLA FRO H Installing the control panel 1 Install the wall mounting with 2 screws 2 Hook one corner of the panel onto the wall mounting 3 Press the other corner of the panel onto the wall mounting z ARITERM H Removing the control panel 1 Slide the panel straight up 2 Lift the panel straight out from the wall r ed F ER t 1 des H Connecting the control panel f B 2 i Connect the control panel in the modular li connection on the side of the control M A circuit board image 3 ARITERM SWEDEN AB Installation Instructions 2011 09 22 8 20 H PELLET STOVE KMP LILLA FRO H 1 5 Safety system The K6 stove is equipped with five independent safety systems 1 The feeder releases pellets into a chute which means that the fuel cannot burn back and spread the fire into the hopper 2 The pellet hopper is equipped with a tight fitting filler hatch The hatch must be closed and locked during use as soon as the hatch is ope
23. pproximately 5 10 mm through the burner flange Fig 10a Fig 10b ARITERM ARITERM SWEDEN AB Installation Instructions 2011 09 22 17 20 H PELLET STOVE KMP LILLA FRO 4 5 Hot air fan Work is best carried out with both side hatches removed but they can also be accessed from one side or the other 1 2 3 4 um H 1 2 3 L1 1 2 Remove the plug from the wall socket Open the top panel Loosen the screw on the top of the side panel Snap the back of the side panel from the stove s back plate by prizing back the top and bottom corners of the side panel Unhook the panel out forwards Carefully pull the connector barrels from the fan motor Loosen from the back the two screws that fasten the fan bracket to the back plate and coax the fan out 4 6 Control circuit board Remove the plug from the wall socket Remove one of the side hatches according to the Hot air fan section Loosen the edge contacts on the control circuit board s long sides by pulling them straight out Disconnect the cable for the control panel located in a connector on the right edge of the control circuit board Press in the hook on the underside of the connector and pull the cable straight out to the side Release the three panel screws on the rear of the stove and remove the control circuit board 4 7 Fuses There are two fuses on the stove s input connector Both are 3 15A slow Wh
24. right side under the insulation Water is penetrating the chimney joints or is seen in the form of grey white smoke Too low output Too low smoke temperature for the chimney Increase the fuel volume The smoke temperature in the chimney 1 m below the top must be at least 60 C After an unsuccessful start attempt or operating stoppage the burner crucible must always be emptied ARITERM SWEDEN AB Installation Instructions 2011 09 22 15 20 H PELLET STOVE KMP LILLA FRO H Error codes ARITERM Error code Cause Action The firing element is not drawing any power Defective firing element Error code Cause Action Powfail Power failure Check the electrical connection Errign Poor contact to firing element Check wiring and connections Replace firing element ErrSafe The flame sensor has not detected a flame when the safety coil has been broken ErrStart The flame sensor has not detected a flame during the start up phase One of the safety thermostats has deployed One of the hatch switches is not switched on The hopper is empty Pellets have jammed in the feeder The feeder auger does not rotate Incorrectly adjusted starting dose Ign dose Check the fuel volume and that the hot air fan functions Clean the convection tubes Reset by pressing on the panel Ensure that the hatch and door
25. rt Stop Stop T Usermenu Back ARITERM Confirm by pressing once to start stop Press to select and adjust desired stop temperature Press for Usermenu Press for display Usermenu Settings Press for Settings Service Menu for authorised service technicians View Press for Display menu See levels operating time programme version etc OnTimer Limited operating time TimeStrt Start at desired time TimeStop Stop at desired time NghtDrop Possibility of lowering temperature below specific time period during the day 1 DayDrop Possibility of lowering temperature below specific time period during the day 2 Assist H Set the lower temperature that is required when maintenance heating is activated Clockset Set date and time Back Press for main menu Settings lt SetCode 021 Service Menu for authorised service technicians gn dose Adjust and test the pellet amount at ignition Adjust the pellet amount at high output TstHdose Test the pellet amount at high output LoPowOn Activate low output FeedLO Adjust the pellet amount at low output TstLdose Test the pellet amount at low output TempDiff Adjust the number of degrees between start and stop AudioOff Sound off or on Language Select language ResOnLog Operational time measurement is reset here Res lgn The counter for number of firings is res
26. start Standby is shown in the display Room temperature exceeds the set value by more than 2 C Set the desired room temperature according to section 1 6 The stove stops shortly after starting excla mation mark in the display Starting dose too small One of the safety thermostats has deployed Adjust the fuel volume Remove the burner and check that the flame sensor is in the correct position and that the lens is clean Clean flue convection tubes fans and ensure that the air intake of the stove is not blocked Pellets do not come out of the feeder The hopper is empty One of the MCBs is not switched on One of the safety thermostats has deployed Pellets have jammed in the feeder The feeder does not rotate Fill up the pellets Ensure that the filler hatch is closed and locked properly A slight clicking noise should be heard when the safety Switch is activated Check the fuel volume and that the hot air fan functions Wait until the stove has cooled Reset by pressing the control panel Feel inside the chute in case pellets have jammed there Empty the hopper Loosen the panel above the feeder screw and remove any blocked pellets Open the filler hatch press down the safety switch to the right of the filling hole If the feeder screw does not move 1 turn min check whether there is a voltage on the motor s terminal block on the hop per s
27. the ash layer in the bottom should be a maximum of a centimetre deep We recommend removing the ash daily during the firing season or each time pellets are filled Remove ash through the door using the handle supplied Lift out the burner from the burner housing and remove any ash from the ash box unburned pellets must not be emptied into the ash box there is a risk of them starting to smoulder Certain pellets generate a hard cake of cinders this may need to be broken up using a screwdriver or removed using one s hands Ash from the stove must be stored in a container made of non flammable material for example a metal bucket until it has cooled sufficiently that it can be held in one s hand It can then be thrown away bear in mind that wood ash contains nutrients that can be beneficial to gardens H 3 3 The glass During firing the stove door can get so hot that it can cause burn injuries if touched After a period of operation the glass in the door becomes coated with ash dust and eventually becomes opaque It should therefore be wiped off from the inside using kitchen roll moistened with normal tap water we recommend that this is done each time the pellets store is filled No cleaning agent is usually necessary When cleaning the black and stainless steel outer panels only use water and where neces sary washing up liquid ARITERM SWEDEN AB Installation Instructions 2011 09 22 13 20 H PELLET STOVE KMP LILLA FRO
Download Pdf Manuals
Related Search