EN Operating Instructions
Contents
1. To clean the dust compartment filters 38 8 Press the dust compartment opening button 13 to open the dust compartment 14 9 Remove the dust container 39 10 Release the opening tab and then remove the Pure Clean Hepa 13 filter pre filter 41 and filter protection grill 40 11 When cleaning the filter protection grill remove any dust powder residues with a small brush lf needed use a damp soft cloth 12 Clean the pre filter by washing it under running water taking care that the jet of water is not too strong Allow to dry 10 13 Wash the Pure Clean Hepa 13 filter under running water taking care that the jet of water is not too strong 14 Hold it so that the water flows parallel to its folds 15 Let it dry at room temperature until all its parts are thoroughly dry L Make sure all its parts are thoroughly L dry before replacing them 16 Fit the pre filter into the special indentation of the Pure Clean Hepa 13 filter locking both filters in place using the protection grill 17 Fit the pre filter Pure Clean Hepa 13 filter and protection grille assembly onto the dust container paying attention to the positions of the notches until it clicks into place 18 Re place the dust container into the dust compartment L The appliance is equipped with a safety yA device that prevents the dust compartment lid from closing unless the dust container has been correctly installed Do not force the dust2. it on standby by pressing the standby button 21 To insert or change the batteries of your Remote Power Control 1 Open the battery compartment 22 Insert two AAA batteries making sure of the positive and negative poles 3 Close the battery compartment until it clicks into place Start amp Stop D The Start amp Stop function if available lets you keep the vacuum cleaner on stand by and lock the cleaning head in the park position just insert the brush into its horizontal housing 29 Dual System E The Trolley Dual Clean version of the Trolley Power makes your use of the appliance extremely versatile because it can be used with or without dust bag Just assemble the conversion kit in the package it comprises a Pure Clean dust bag 34 dust bag support 33 gasket 37 and motor filter grill 36 already fitted to the motor filter 35 hotpoint co uk 7 The assembling takes place as follows 1 Make sure the appliance is disconnected from the electrical outlet 2 Press the dust compartment opening button 13 to open the dust compartment lid 14 and remove the dust container 39 3 Fit the gasket into the special groove along the perimeter of the dust compartment 38 4 Fit the motor filter grill already fitted to the motor filter into the special dust compartment guides 5 Slide the Pure Clean dust bag into the dust bag support all the way then place it into the special dust compar
3. replaced become our proper ty e The product is used in the United Kingdom or Republic of Ireland The Guarantee does not cover Damage resulting from transportation im proper use neglect or interference or as a result of improper installation e Accidental damage this includes but is not limited to damage which occurs as a result of an external action Replacement of any consumable item or ac cessory These include but are not limited to plugs cables light bulbs hoses brushes covers and filters Replacement of any removable parts made of glass or plastic After Sales Service No one is better placed to care for your Hotpoint product during the course of its working life than us the manufacturer Essential Contact Information Advice Line We have a dedicated team who can provide free advice and assistance with your product if you experience any technical difficulties Simply call E hotpoint co uk 13 our Hotpoint Service Hotline on 08448 240 055 Republic of Ireland 0818 904 041 for telephone assistance Please note Our advisors will require the following infor mation Consumables and Accessories We supply a full range of consumables and ac cessories to keep your product functioning effi ciently throughout its life UK 08448 225 225 Republic of Ireland 0818 313 413 www hotpoint co uk Recycling and Disposal Information As part of Hotpoint s continued commitment to he
4. the Pure Clean dust bag or dust container correctly and close the dust compartment lid until it clicks into place L3 The appliance is equipped with a safety Y device that prevents the dust compartment lid from closing unless the dust bag container has been correctly installed Replacing the Pure Clean dust bag G We recommend always using Hotpoint original Pure Clean dust bags because their special fabric allows optimum air filtration maximum dust powder retention high performances and a long motor life As the Pure Clean dust bags 34 are made of fabric they are more resistant than conventional paper bags and can retain very fine dust powder particles more effectively thus ensuring maximum hygiene L3 We recommend replacing the Pure J Clean bag as soon as the full bag indicator illuminates Change at least once a year to be always sure of the hygienic condition of your vacuum cleaner The pores of a bag clogged with dust powder particles reduce the motor s suction power and can cause damage 1 Make sure the appliance is disconnected from the electrical outlet 2 Press the dust compartment opening button 13 to open the dust compartment lid 14 3 Release the bag support 33 and remove the Pure Clean dust bag 34 L3 Dispose of the dust bag in compliance VA with all local regulations on waste disposal 4 Slide a new Pure Clean dust bag into the dust bag support completely then place it b
5. 8 8 Press the dust compartment opening button 13 to open the dust compartment lid 14 9 Remove the Pure Clean dust bag 34 motor filter grill 36 and motor filter 35 from the motor filter grill 10 Clean the motor filter by washing it under running water taking care that the jet of water is not too strong Then gently shake water loose 11 When cleaning the motor filter grill remove any dust powder residues with a small brush If needed use a damp soft cloth L3 Make sure all its parts are thoroughly A dry before replacing them 12 Fit the motor filter into the motor filter grill again taking care to position it gently into the special notches 13 Slide the motor filter grill assembly into the special guides in the dust compartment 14 Fit the Pure Clean dust bag using the special dust bag support L3 The appliance is equipped with a safety S device that prevents the dust compartment lid from closing unless the dust bag has been correctly installed Do not force the dust bag lid to close and make sure all the parts are in the correct position to allow you to close the lid 15 Close the dust compartment lid until it clicks into place For the routine cleaning of the dust container 1 Press the dust compartment opening button 13 to open the dust compartment 14 and remove the dust container 39 2 Open the lid and empty the dust container 3 Remove any residual dirt by washing the dust c
6. K Hotpoint Th SA EN Operating Instructions y TTD A y DESCRIPTION OF THE VACUUM CLEANER Standard Carpet brush Bristle adjustment pedal Parquet brush Turbo brush Upholstery brush Deluxe Parquet brush Pipe length regulator Metal extension pipe 9 Hand grip 10 Plastic hose 11 Carrying handle 12 Trolley System opening closing button 13 Dust compartment opening button 14 Dust compartment lid 15 Suction inlet 16 Release 17 Full dust bag container indicator 18 Start Stop button 19 Cord rewind button 20 Buttons for electronic power adjustment 21 Standby button 22 Battery compartment 23 Air regulator 24 Remote Power Control signal receiver 25 Electronic power regulator INTRODUCTION a ole SS Thank you for purchasing our Trolley Power vacuum cleaner In doing so you have opted for an effective high performance appliance We advise you to register this product on www hotpoint co uk to make sure you are entitled to all the benefits made available by Hotpoint Customer Service The Trolley Power was designed to ensure optimum performance and consistent usability The exclusive Trolley System ensures maximum manouverability and helps you move freely around the house without knocking against the furniture The Remote Power Control if available enables you to adjust the suction power directly and effortlessly from the hand grip with no need to bend This app
7. ack into the special compartment 5 Close the dust compartment lid until it clicks into place L3 If you are finding it difficult to close the Y dust compartment lid it is likely that the Pure Clean dust bag and or its dust bag support have not been assembled correctly Do not force the dust bag lid to close make sure both parts are in the correct position to allow lid closure Cleaning the filters H model with dust bag The Pure Clean Hepa 13 filter ensures maximum protection against allergens and maintains high air quality as the air given back by the appliance is entirely free from dust powder residues filtering power gt 99 95 L3 We advise you to clean the filter at least Dd every 4 months to restore its filtering power In any case we recommend replacing the filter at least every year to ensure maximum performance To clean the Pure Clean Hepa 13 filter 30 1 Disassemble the air grill 31 using the opening tab 2 Remove the Pure Clean Hepa 13 filter by releasing the opening tab 3 Wash the filter under running water taking care that the jet of water is not too strong 4 Hold it so that the water flows parallel to its folds 5 Let it dry at room temperature until all its parts are thoroughly dry 6 Replace the Pure Clean Hepa 13 filter paying attention to the position of the notches 7 Fit the air grill into its housing until it clicks into place To clean the dust compartment filters 3
8. ature is available you can use the standby button 21 on the Remote Power Control or the Start amp Stop function based on the model Just insert the brush into its horizontal housing 29 6 To switch off the appliance press the start stop button again 7 Disconnect the plug from the electrical outlet and press the cord rewind button 19 until rewinding is complete L Make sure the cord does not get Y entangled during rewinding 8 Secure the floor head into its horizontal vertical housing and store the appliance A Do not start the vacuum cleaner if the plastic flexible hose is entangled as this could damage the appliance FEATURES Trolley System B The Trolley System allows you to move your vacuum cleaner easily when cleaning and carry it from room to room effortlessly 1 Press the opening closing button on the Trolley System 12 to pull out the carry handle 11 until it locks into place at the desired length 2 Having completed your cleaning press the opening closing button on the Trolley System and close the carrying handle until it locks into place y Use the Trolley System s carrying A handle to store the appliance making sure you have correctly locked it into place Remote Power Control C The Remote Power Control if available enables you to adjust the suction power directly and effortlessly from the hand grip 9 with no need to bend When using the vacuum cleaner you can keep
9. bag lid to close it and make sure allthe parts are in the correct position to allow lid closure 19 Close the dust compartment lid until it clicks into place ATTACHMENTS The attachments can either be supplied as standard features based on the model or be purchased separately from Hotpoint authorised centres L Before changing an attachment during Y maintenance disconnect the plug from the electrical socket Do not use aggressive substances or abrasive materials to clean the appliance its internal parts and attachments Make sure the appliance is thoroughly dry before using it again Standard Carpet brush K The standard carpet brush 1 is suitable for vacuuming hard and smooth floors as well as carpets on a daily basis Use the bristle adjustment pedal 2 to clean assess Carpets Hard floors To clean the plastic parts of the standard carpet brush remove the brush from the metal extension pipe 8 and wipe with a dry or slightly damp soft cloth To clean the bristles remove any dirt using if needed the precision nozzle 26 Parquet brush L The Parquet brush 3 is suitable for vacuuming delicate areas such as wooden floors The special natural bristles enable you to use on very delicate surfaces without harm To clean the plastic parts of the Parquet brush remove the brush from the metal extension pipe 8 and wipe with a dry or slightly damp soft cloth To clean the bristles suck up any dirt usi
10. cted Consumers should contact their local authority or retailer for information concerning the correct disposal of their old appliance Indesit Company UK Ltd Morley Way Peterborough PE2 9JB www indesitecompany com B Hotpoint Trolley Power 2013 06 ver 1 1
11. e 3 Fit the standard carpet brush 1 or the attachment you need see chapter Attachments into the end of the metal extension pipe until it locks into place L3 If your appliance is equipped with a Y Remote Power Control you will need to insert the batteries supplied see paragraph Remote Power Control under chapter Features USING THE VACUUM CLEANER A Do not use the vacuum cleaner without filters Pure Clean dust bag dust bag support or dust container as the appliance could get damaged 1 Unwind the power cord 32 and plug the appliance into an electrical outlet 220 240V We advise you to unwind the entire g power cord app 7m to avoid any overheating and damage 2 Press the start stop button 18 to start the appliance 3 Press the Trolley System opening closing button 12 to extend the carrying handle 11 to the desired length until it locks into place Then manoeuvre the vacuum cleaner using the carrying handle when cleaning the house 4 To select the desired suction intensity based on the model use the button and electronically adjust the power 20 of the Remote Power Control or manually rotate the electronic power regulator 25 L3 We advise you to use a low suction af Gower on delicate surfaces such as curtains fabrics cushions etc to avoid any damage or at least open the air regulator to reduce the suction effect 5 To pause the vacuum cleaner if this fe
12. e positive and negative poles Electronic appliances or obstacles may be interfering or shielding with the infrared signal If very fine dust or powders are sucked up such as flour etc small electrostatic discharges could occur When sucking up materials previously mentioned we advise not to use the metal extension pipe but only the plastic flexible hose and to set a low suction power level One or more attachments were assembled incorrectly Make sure the filters and brushes were assembled according to these instructions In the model with dust bag make sure that the gasket is correctly in place too The dust bag container is full Replace the dust bag or clean the dust container Clean the filters and if needed replace them The air regulator is open Make sure it was closed correctly The dust compartment lid e cannot be closed The Pure Clean dust bag or dust container was assembled incorrectly Make sure it is correctly in place so that the safety lever will let you close the dust compartment lid The brush is difficult to o move The cord is difficult to o rewind rewind GUARANTEE 12 months Parts and Labour Guarantee This certificate of guarantee represents the gua rantee Guarantee hereinafter offered by In desit Company UK Limited with registered office at Peterborough PE2 9JB in relation to products purchased in the United Kingdom and Indesit Ireland Limited with registered office in Dublin 9 Ire
13. land for products purchased in the Republic of Ireland This Guarantee does not affect your sta tutory rights Your product has the benefit of our manufactu rers Guarantee which covers the product for twelve months from the date of purchase This gives you the reassurance that if within that time your product is proven to be defective be cause of either workmanship or materials we will at our discretion either repair or replace the pro duct at no cost to you This Guarantee is subject to the following condi tions e Documentary proof of original purchase date is provided Cosmetic damage must be reported within 14 days from the date of purchase e The product has been installed and operated correctly and in accordance with our opera ting and maintenance instructions The product is used only on the electricity supply printed on the rating plate e The product has been used for normal do mestic purposes only The product has not been altered serviced Reduce suction power especially on carpets and fabrics in general Open the air regulator to reduce the suction effect Make sure the cord does not get entangled during rewinding If it is stuck unwind the entire power cord again and repeat maintained dismantled or otherwise interfe red with by any person not authorised by us Any repair work must be undertaken by us or our appointed agent Any parts removed during repair work or any product that is
14. les operated by the vacuum cleaner s suction power that enable you to clean in depth and remove any fur hairs or mites from fabrics The protection grill prevents the bristles from touching the surfaces to be cleaned thus ensuring maximum on fabrics To clean the plastic parts of the Upholstery brush remove the brush from the metal extension pipe 8 and wipe with a dry or slightly damp soft cloth To clean the rotating bristles release the lid by releasing its fastening elements then disassemble the rotating brush and start cleaning Remove any hairs or threads that got entangled using scissors taking care not to damage the bristles Precision nozzle P The precision nozzle in the attachment compartment 28 helps you vacuum corners crevices and other difficult to reach areas To clean the precision nozzle remove the nozzle from the metal extension pipe 8 and wipe with a dry or slightly damp soft cloth Nozzle for delicate surfaces Q The nozzle for delicate surfaces in the attachment compartment 28 is suitable for vacuuming surfaces requiring special care such as radiators furniture etc Its special natural bristles enable you to use it on very delicate surfaces without any harm To clean the plastic parts of the nozzle for delicate surfaces remove the nozzle from the metal extension pipe 8 and wipe with a dry or slightly damp soft cloth To clean the bristles remove any dirt using if needed the precision noz
15. liance was developed for household use only and should not be put to industrial use 26 Precision nozzle 27 Nozzle for delicate surfaces 28 Attachment compartment 29 Horizontal housing 30 Pure Clean Hepa 13 filter 31 Air grill 32 Power cord Version with dust bag 33 Dust bag support 34 Pure Clean dust bag 35 Motor filter 36 Motor filter grill 37 Gasket 38 Dust compartment Version without dust bag 38 Dust compartment 39 Dust container 40 Filter protection grill 41 Pre filter 42 Pure Clean Hepa 13 filter Before you begin using the appliance it is important that you carefully read these instructions and keep them for further reference GENERAL SAFETY RULES The safety features of your vacuum cleaner comply with the technical specifications and regulations in force Do not use the appliance for any use other than its intended use Any improper use could cause damage to persons and or property The voltage of your system must match the voltage of the vacuum cleaner 220 240 V Any connection error could cause irreversible damage to the appliance and void its warranty e If the plug power cord or appliance appear to be damaged or if any visible damage is hotpoint co uk 9 found do not operate the vacuum cleaner In such cases have it checked exclusively by Hotpoint authorised staff in order to avoid any hazardous situation Regularly check the condition of the powe
16. lping the environment Hotpoint reserves the right to use quality recycled components to keep down customer costs and minimise material wa stage Please dispose of packaging and old products carefully Register your new product and get a second year FREE We want to give you additional benefits of owner 14 ship of your product and offer you an additional free 1 year guarantee when you register your product with Hotpoint within 28 days of purchase If you do not register your product with Hotpoint within 28 days your product is guaranteed for 1 year only To activate your 2 year guarantee register with us Online at www hotpoint co uk Please note that the 2 year guarantee is only available in UK and Ireland and is subject to the same conditions as the 1 year Guarantee Please refer to the certifica te of guarantee for more information DISPOSAL OF OLD ELECTRICAL APPLIANCES The European Directive 2002 96 EC on Waste Electrical and Electronic Equipment WEEE requires that old household electrical appliances must not be disposed of in the normal unsor ted municipal waste stream Old appliances must be collected sepa rately in order to optimise the recovery and recycling of the materials they con tain and reduce the impact on human health and the environment The crossed out wheeled bin symbol on the product reminds you of your obligation that when you dispose of the appliance it must be separately colle
17. ng the precision nozzle 26 Turbo brush M The Turbo brush 4 is ideal for the in depth vacuuming of short pile carpets and removing pet hair The rotation of the brush is operated by the vacuum cleaner s suction power To clean the plastic parts of the Turbo brush remove the brush from the metal extension pipe 8 and wipe with a dry or slightly damp soft cloth Remove any hairs or threads that got entangled in the rotating brush using scissors taking care not to damage the bristles Deluxe Parquet brush N The Deluxe Parquet brush 5 is suitable for vacuuming delicate and parquet floors The brush is equipped with very delicate rotating bristles which are operated by the vacuum cleaner s suction power and soft wheels protecting delicate floors To clean the plastic parts of the Deluxe Parquet brush remove the brush from the metal extension pipe 8 and wipe with a dry or slightly damp soft cloth To clean the rotating bristles turn the safety lock into position and Na remove then disassemble the rotating brush and start cleaning Remove any hairs or threads that got entangled using scissors taking care not to damage the bristles A For your safety never put your hands close to the suction nozzle or rotating brush while operating the appliance Upholstery brush O The Upholstery brush 6 is suitable for vacuuming surfaces such as sofas mattresses blankets cushions etc It is equipped with rotating brist
18. ontainer under running water 4 Let it dry at room temperature until all its parts are thoroughly dry 5 Close the dust container lid until it clicks into place and replace it into the dust compartment 6 Close the dust compartment lid until it clicks Cleaning the dust container I model without dust bag AAA hotpoint co uk 9 into place Cleaning the filters J model without dust bag 2 This model comprises two Pure Clean Hepa 13 filters The Pure Clean Hepa 13 filter ensures maximum protection against allergens and high air quality because the air given back by the appliance is entirely free from dust powder residues filtering power gt 99 95 L3 We advise you to clean the filter at least y every 4 months to restore its filtering power In any case we recommend replacing the filter at least every year to ensure maximum performance To clean the Pure Clean Hepa 13 filter 30 in the back 1 Disassemble the air grill 31 using the opening tab 2 Remove the Pure Clean Hepa 13 filter by releasing the opening tab 3 Wash the filter under running water taking care that the jet of water is not too strong 4 Hold it so that the water flows parallel to its folds 5 Let it dry at room temperature until all of it s parts are thoroughly dry 6 Re place the Pure Clean Hepa 13 filter paying attention to the positions of the notches 7 Fit the air grill into its housing until it clicks into place
19. r cord If the fuse in the plug malfunctions the appliance will stop operating e This appliance was not designed to be used by persons including children with reduced physical sensory or mental capabilities Nor in addition persons lacking experience or familiarity with the product unless they are supervised or instructed on the use of the appliance by a person responsible for their safety Supervise children to prevent them from playing with the appliance e Never leave the appliance unattended when it is plugged into an electrical outlet Never use the power cord to move or carry the appliance around e After use disconnect the plug from the electrical outlet and rewind the power cord Do not bend the power cord and keep it away from sharp edges to avoid any damage e Never leave or use the appliance over or close to flames ovens flammable materials or other sources of heat Do not use the vacuum cleaner on persons or animals Keep the suction ends away from your body while it is in operation Before changing an attachment when cleaning or maintaining the appliance and in any case after every use unplug it from the electrical outlet e Should you suspect a failure immediately unplug it from the electrical outlet Never immerse the vacuum cleaner in water or any other liquid Never spray any liquid substances onto the appliance Do not leave the appliance in the open air and exposed to inclemen
20. t weather conditions e For safety we advise you to keep the vacuum cleaner always lower than your own position when cleaning the stairs N Never suck up any liquid or damp substances as this could affect the operation of the appliance Never suck up any flammable materials or incandescent objects such as ash cigarette ends etc Some parts of the vacuum cleaner could catch fire e Never suck up any sharp or cutting objects as this could damage the appliance If very fine dust or powders are sucked up such as flour etc small electrostatic discharges could occur When sucking up materials previously mentioned we advise not to use the metal extension pipe but only the plastic flexible hose and to set a low suction power level For your safety every repair or maintenance action should be carried out on the appliance only by Hotpoint authorised staff No responsibility shall be accepted in case of damage resulting from any improper use of the appliance BEFORE FIRST USE Remove all adhesives protective plastic materials and cardboard packaging Make sure all adhesive parts are removed with a soft damp cloth Assembling 1 Fasten the plastic flexible hose 10 to the suction inlet 15 until it clicks into place To remove it press the release 16 and pull it out 2 Fit the metal extension pipe 8 into the hand grip 9 until itlocks into place Use the length regulator 7 to adjust the length of the pip
21. tment The appliance is equipped with a safety 7 device that prevents the dust compartment lid from closing unless the dust bag container has been correctly installed 6 Close the dust compartment lid until it clicks into place To use the vacuum cleaner with the dust Y container remember to remove all the following parts Pure Clean dust bag dust bag support gasket motor filter and motor filter grill CLEANING AND MAINTENANCE L3 Before cleaning or maintaining the Y vacuum cleaner make sure it has been unplugged from the electrical outlet Do not use aggressive substances or abrasive materials to clean the appliance its internal parts and attachments Make sure it is thoroughly dry before using again Cleaning the appliance Use a dry or slightly damp soft cloth to clean the plastic parts body dust compartment flexible hose etc and the metal extension pipe 8 Cleaning the attachments Before cleaning the attachments refer to the chapter Attachments 8 Cleaning the dust compartment F For the routine cleaning of the dust compartment 38 1 Press the dust compartment opening button 13 to open the dust compartment lid 14 2 Based on the model remove the Pure Clean dust bag 34 or the dust container 39 3 Clean the dust compartment by removing any residual dirt with a small brush If needed use a damp soft cloth taking care to wipe all its parts entirely dry 4 Re place
22. zle 26 E hotpoint co uk 11 TROUBLESHOOTING Possible causes Solutions Problem The vacuum cleaner cannot be switched on The full dust bag container indicator lights up although it is not full yet Low suction power Remote Power not working Small electrostatic discharges occur while sucking up The vacuum cleaner whistles or vibrates when in use 12 The plug was not inserted or is not making contact Change the dust bag If large quantities of very fine dust powder are sucked up e g flour etc the full dust bag indicator may light up although the bag is not full yet The reason is that the Pure Clean dust bag is able to retain very fine dust powder particles thus ensuring maximum hygiene Clean the dust container in models without dust bag Clean the filters and if needed replace them Make sure the expansion pipe flexible hose and brush are not blocked Clean the filters and if needed replace them Make sure the expansion pipe flexible hose and brush are not blocked Change the dust bag If large quantities of very fine dust powder are sucked up e g flour etc the Pure Clean dust bag may become clogged Clean the dust container and its filters Battery not charged The batteries were positioned incorrectly inside the battery compartment Position the two AAA batteries making sure of the positive and negative poles Remove batteries then position them again making sure of th
Download Pdf Manuals
Related Search