Home

Operating Instructions

image

Contents

1. Open the service door for tank Pos 7 Remove the dust collecting tank Pos 9 from the dust collecting housing Pos 6 The collect dust must be stored properly in a suitable container and disposed of according to pertinent regulations Push the dust collecting tank Pos 9 into the dust collecting housing Pos 6 Hook in and close the clamping fasteners so that the tank Pos 9 seals tightly under the chute Pos 8 of the filter unit check the sealing under the chute Pos 8 for damages and if applicable replace Connect the control for the cleaning with the power supply Observe the information on the nameplate Caution We recommend using A respiratory mask according to DIN EN 141 143 Protection class P3 The work processes specified above may only be carried out by a correspondingly trained employee The dust must be disposed of according to relevant legislation and directives 13 4 Discharging the condensation The resulting condensation in the compressed air tank Pos 16 is to be emptied at regular intervals at least however once a month The dust collecting tank may only be emptied by qualified personnel Remove all persons who are not required for the work which is to be directly carried out from the danger zone or if applicable additionally equip with protective equipment Disconnect the machine from the power supply and secure against being switched on again Disconnect the filter uni
2. Observe the correct position of the extraction element and details on the nameplate Follow the manufacturer s instructions Remove all persons who are not required for the work which is directly to be carried out from the danger zone or if applicable additionally equip with protective equipment If not otherwise possible use additionally authorized protective equipment for the user such as e g respiratory mask eye protectors noise protection We recommend using a respiratory mask according to DIN EN 141 143 Protection class P3 E Caution Only use original TEKA products 13 Maintenance and service The accumulation of extracted particles on the filter cartridge will eventually lead to a reduction of the suction extraction performance The level of saturation of the filter cartridge is monitored electronically The filter cartridge is cleaned automatically in order to retain the admissible suction performance of the unit see chapter 13 1 Cleaning of the filter cartridges The accumulated dust particles are blown off the filter by applying compressed air from the clean side The released filter cake will drop into the dust collecting tank see chapter 13 3 Emptying of dust collecting tank The useful service life of the filter cartridge greatly depends on the operational environment For this reason it cannot be predicted Should after cleaning the filter cartridge the operating pressure of the filter system no longer b
3. Operating Instructions TEKA FILTERCUBE 4 TEKA Absaug und Entsorgungs technologie GmbH Industriestra e 13 D 46342 Velen Postfach 1137 D 46334 Velen Tel 49 0 2863 9282 0 Fax 49 0 2863 9282 72 E Mail sales tekanet de www tekanet de We set air in motion Contents 12 13 13 1 13 2 Drawing Description of components Introduction Function of the TEKA FILTERCUBE 4 Safety instructions Transport Installation Initial operation Mounting of extraction and suction elements Electrical connection Pre coating of the filter cartridges Connection of the compressed air supply Explanation of the Controls Test run Set extraction elements Other extraction elements Operation Maintenance and service Cleaning of the filter cartridges Compressed air supply 13 3 Emptying of the dust collecting tank 13 4 Discharging the condensation 13 5 Replacement of the filter cartridges 14 14 1 14 2 14 3 15 16 17 18 Error search No function Suction performance too low Insufficient extraction Disassembly disposal Technical Data List of spare parts Declaration of conformity TEKA Filtercube 4 BA _Filtercube4_091217_GB neu doc 17 12 2009 3 5 5 6 7 7 8 8 8 9 We set air in motion 1 Drawing Description of components Filtercube 4N Zeichnungs Nr 05363700 Pos 1a Joggle button Pos 10 Intake stub Pos 1b S
4. The exhaust air element is to be fastened to the exhaust outlet Pos 11 using a suction pipeline Remove all persons who are not required for assembling the extraction or exhaust element from the danger zone Only use TEKA extraction elements and TEKA exhaust elements The machine must be easily accessible from all sides Observe the manufacturer s instructions or contact the manufacturer 7 2 Electrical connection Observe the information on the nameplate The machine may only be connected by authorized and skilled electricians Remove all persons who are not required for connecting the unit from the danger zone Connect the filter unit to the mains supply The machine must be easily accessible from all sides Observe the manufacturer s instructions or contact the manufacturer Caution Work on the electrical components may only be carried out by authorized personnel Observe the information on the nameplate BA_Filtercube4_091217_GB neu doc 8 17 12 2009 We set air in motion 7 3 Pre coating of the filter cartridges The filter cartridges only have to be pre coated ifthese have not already been pre coated by the plant If there is any doubt about the application please contact the manufacturer Observe the information on the nameplate The pre coating may only be carried out by qualified personnel Remove all persons who are not required for the pre coating of the filter cart
5. travel across the breathing space of the worker upwards before they are collected and taken out This is surely not the point of the exercise A much more effective method than overhead wide area extraction is the removal of pollutants directly at their source with localised extraction Both the initial investments and the running costs are considerably lower with localised extraction Localised extraction works best however when the work process itself is operating optimally and of course the correct measures must be in place regarding the environment and the prevention of accidents at work In a time of increasing sensitivity and tougher legislation the task therefore lies in making an early assessment of the potential hazards for the workplace and the environment and reducing them as appropriate 3 Function of the TEKA FILTERCUBE 4 The filter unit TEKA FILTERCUBE 4 is primarily used for extracting dust and fumes For this purpose the unit must be equipped with the corresponding application specific fittings The polluted air is extracted via a specific extraction fitting and gets through the pipeline into the filter unit The rough dust particles are deflected here on the integrated perforated plate The particle shaped pollutants are discharged on the surface of the following filter cartridges The cleaned air is sucked by the ventilator and discharged outside or recycled into the work room via a corresponding exhaust air line As
6. work In case of leakage of the pneumatic system the suction unit must not be put into operation anymore Without compressed air supply the filter cartridge gets dirty very fast and the device switches to disturbance filter full BA_Filtercube4_091217_GB neu doc 12 17 12 2009 We set air in motion TE 13 3 Emptying of the dust collecting tank The dust collecting tank must be emptied after a certain number of operating hours This is determined according to the incurred volume of dust the dust collecting tank must however be emptied at least once a week The dust collecting tank may be filled however to a maximum 25 If there is any doubt about the application please contact the manufacturer The dust collecting tank may only be emptied by qualified personnel Remove all persons who are not required for the work which is to be directly carried out from the danger zone or if applicable additionally equip with protective equipment Disconnect the machine from the power supply and secure against being switched on again Empty the compressed air tank Pos 16 by opening the ball valve Pos 27 Condensation can leak by opening the ball valve Close the ball valve again Pos 18 when the compressed air tank Pos 16 is completely empty Suitable respiratory protection and eye protectors are to be worn when servicing the unit We recommend using A respiratory mask according to DIN EN 141 143 Protection class P3
7. TEKA Absaug und Entsorgungstechnologie GmbH Industriestr 13 D 46342 Velen Tel 49 2863 92820 Fax 49 2863 928272 e Mail sales tekanet de Internet http www tekanet de We herewith declare in sole responsibility that the above mentioned product starting from machine No 110000000 conforms to the following standards Directives on machine building 2006 42 EG Electromagnetic compatibility 2004 108 EG Directives on pressure device 97 23 EG Directives on low voltage 2006 95 EG Applied harmonised standards DIN EN 349 DIN EN 983 DIN EN 12100 part 1 and part 2 DIN EN 60204 part 1 DIN EN ISO 13857 DIN EN ISO 14121 plus further national standards and specifications DIN 45635 part 1 This declaration will become void if changes are effected to the suction and filter systems which were not agreed upon in writing by the manufacturer a Velen 17 12 09 TEKA Absaug und Entsorgungstechnologien GmbH BA _Filtercube4_091217_GB neu doc 19 17 12 2009
8. all persons who are standing around from the danger zone Observe the manufacturer s instructions or contact the manufacturer Installation Wear safety shoes with steel caps Remove all persons who are not required for installation from the danger zone Stipulate instructions for surface and load bearing capacity The machine must be easily accessible from all sides Observe the manufacturer s instructions or contact the manufacturer BA_Filtercube4_091217_GB neu doc 7 17 12 2009 We set air in motion 7 Initial operation Observe the information on the nameplate The machine may only be connected by authorized and skilled electricians Remove all persons who are not required for connecting the power supply from the danger zone The extraction elements and if applicable other accessories must be mounted or installed to the unit prior to initial operation E The filter cartridges must be pre coated before initial operation if these have not already been pre coated by the plant If there is any doubt about the application please contact the manufacturer The machine must be easily accessible from all sides Observe the manufacturer s instructions or contact the manufacturer 7 1 Mounting of extraction and suction elements The assembly may only be carried out by qualified staff The extraction element is to be fastened to the intake stub by means of a suction pipe or suction hose Pos 10
9. ce and service contract Our customer services by phone Feel free to contact our Service Department where you will be assisted 24 hours a day Phone 0 28 63 92 82 0 Fax 0 2863 92 82 72 BA_Filtercube4_091217_GB neu doc 16 17 12 2009 We set air in motion 16 Technical Data Caution Observe the information on the nameplate TEKA FILTERCUBE 4 BEE RCE te te tn 3500 4000 5000 6000 7500 10000 a co Nasr ra 00e e00 200 we om an E E E Cr BE BE 7 Bann m prso I I en Noise level dB A Measured as per DIN 45635 T1 in free air at 1m distance from the surface of the machine max airflow volume Compressed air supply wi dry oil free BA_Filtercube4_091217_GB neu doc 17 17 12 2009 We set air in motion 17 List of spare parts Designation Motor 2 2 kW 400V 3 Ph 50 Hz Motor 3 0 kW 400V 3 Ph 50 Hz Motor 4 0 kW 400V 3 Ph 50 Hz Motor 5 5 kW 400V 3 Ph 50 Hz Motor 7 5 kW 400V 3 Ph 50 Hz Motor 11 0 kW 400V 3 Ph 50 Hz Filter cartridge 7 5m Filter cartridge 10m Star filter cartridge Type easy clean 12 5m Filter cartridge 15m Filter cartridge 20m Star filter cartridge Type easy clean 25m BA _Filtercube4_091217_GB neu doc Article no 20000010 20000006 20000005 20000021 20000022 20000016 10025075 10025 100050125 10027 100090200 100050250 17 12 2009 We set air in motion 18 Declaration of conformity TEKA Filtercube 4
10. e reached the red indicator lamps will illuminate see separate operating instructions of the software and the filter cartridge must be replaced see chapter 13 5 Replacement of the filter cartridges Caution Disconnect from the mains supply when cleaning or servicing the unit when exchanging any parts or when changing machine settings for a different function and secure against being switched on again The operation of the filter unit must be interrupted when changing the filter cartridge The compressed air tank is to be emptied before carrying out all maintenance and repair work Exchange of the filter cartridge and the disposal of the element may be executed only in amply ventilated environments and when using an appropriate protective respiratory mask We recommend using A respiratory mask according to DIN EN 141 143 Protection class P3 The task of changing the filter elements should be executed by trained personnel only BA_Filtercube4_091217_GB neu doc 11 17 12 2009 We set air in motion 13 1 Cleaning of the filter cartridges The level of saturation of the filter cartridges is monitored electronically The filter cartridge is cleaned automatically in order to retain the admissible suction performance of the unit The filter unit remains in operation status during the automatic cleaning Should the cleaning process no longer manage to clean the filter cartridge at its operating pressure then the filter cartridge must b
11. e replaced see chapter 13 5 Replacement of the filter cartridges 13 2 Compressed air supply Suitable compressed air supply must be proved to ensure the correct function of the suction unit The compressed air supply may only be checked by qualified personnel Remove all persons who are not required for the work which is directly to be carried out from the danger zone or if applicable additionally equip with protective equipment The compressed air must be dry and oil free The resulting condensation in the compressed air tank Pos 16 is to be emptied at regular intervals If an upstream water trap should be used available as an option this is also to be controlled at regular intervals and emptied if necessary The pneumatic components are to be checked regularly for tightness The external compressed air must be supplied via an authorized compressed air hose The supplied operating pressure must be a minimum 1 bar and maximum 6 bar and must be set dependent on the process As buffer reserve a compressed air tank is installed in the pneumatics housing Contents are sufficient for one cleaning session The external compressed air supply must be designed to the extent that the compressed air tank reaches the operating pressure again within the valve ideltime see separate operating instructions of the software Caution The compressed air tank is to be emptied before carrying out all maintenance and repair
12. ied Suitable protection equipment such as e g respiratory mask and eye protectors must be worn when opening the filter part We recommend using a respiratory mask according to DIN EN 141 143 Protection class P3 14 3 Insufficient extraction The extraction device must be designed to the extent that its extraction elements are adjusted to the local conditions and the dimensions take into account the volume of air pollution Contact manufacturer if applicable application technician Consultancy on site 15 Disassembly disposal The machine or electrical system electrical line may only be dismantled by qualified electricians Before disassembly disconnect the machine from the power supply and from the external compressed air supply The compressed air tank must be emptied Suitable respiratory protection and protective clothing are to be worn with all work We recommend using a respiratory mask according to DIN EN 141 143 Protection class P3 The pollutants or the filter media must be disposed of properly Observe the manufacturer s instructions or contact the manufacturer To ensure an efficient and orderly operation of your TEKA FILTERCUBE 2 extraction unit and for compliance with the correct disposal of the collected dust media we offer the following services Assistance in looking for a local waste disposal company A list of disposal companies in Germany can be provided upon request at no extra cost A maintenan
13. isconnect the filter unit from the external compressed air supply Empty the compressed air tank Pos 16 by opening the ball valve Pos 18 Condensation can leak by opening the ball valve Close the ball valve again Pos 18 when the compressed air tank Pos 16 is completely empty Suitable respiratory protection and eye protectors are to be worn when opening the machine We recommend using A respiratory mask according to DIN EN 141 143 Protection class P3 Open the cartridge door Pos 5 Release the locking screw Pos 15 of the cartridge bracket Pos 14 Pull out the filter cartridges Pos 13 Push the new filter cartridge into the cartridge guidance which is mounted under the intermediate plate Pos 21 BA_Filtercube4_091217_GB neu doc 14 17 12 2009 We set air in motion Caution Only use original TEKA replacement filter Tighten the locking screw Pos 15 of the cartridge bracket Pos 14 Close the cartridge door Pos 5 e Connect the filter unit to the mains supply Observe the information on the nameplate 7 Pre coat the filter see chapter 7 3 Pre coating of the filter cartridges The compressed air may not be connected until the filter differential pressure value is reached which is set in the pulsecontrol when cleaning begins see separate operating instructions of the software Caution Exchange of the filter and the disposal may be executed only in amply ventilated rooms and when u
14. meplate The trial run of the machine may only be carried out by qualified personnel All persons who are not required for the trial run are removed from the danger zone The machine must be easily accessible from all side Observe the manufacturer s instructions or contact the manufacturer 10 Set extraction elements They must be positioned directly on or as close as possible to the point of production localised extraction For the protection of the health the industrial safety act ArbSchG stipulates that the dangers involved with the work for the employees must be determined assessed and corresponding industrial safety measures be carried out i If not otherwise possible use additionally authorized protective equipment for the user such as e g respiratory mask eye protectors noise protection We recommend using a respiratory mask according to DIN EN 141 148 Protection class P3 Remove all persons who are not required for the work which is to be directly carried out from the danger zone or if applicable additionally equip with protective equipment The machine must be easily accessible from all side Observe the manufacturer s instructions or contact the manufacturer BA_Filtercube4_091217_GB neu doc 10 17 12 2009 We set air in motion 11 Other extraction elements Observe the manufacturer s instructions or obtain release of the manufacturer Consult application technicians 12 Operation
15. mist greases separating agents e g silicon spray cleaning agents etc Do not use the unit for the extraction of aggressive media Do not use the unit for sucking liquids of any kind Do not use the unit for extraction of any organic matters without the written permission of the manufacturer Protect the connecting lead from heat moisture oils and sharp edges Pay attention to the correct voltage Observe the information on the nameplate Only use original TEKA spare parts Do not operate the unit without a filter cartridge installed Disconnect the filter unit from the mains supply before opening the unit and secure against it being switched on again The compressed air tank is to be emptied before carrying out all maintenance and repair work The exhaust outlet must not be obstructed or blocked in any way Always take care that the unit stands secured and that the caster brakes are set Disconnect from the mains supply when cleaning or servicing the unit when exchanging any parts or when changing machine settings for a different function and secure it against being switched on again The filter cartridges cannot be regenerated for repeated use The filters must be disposed of according to relevant legislation and directives At regular intervals inspect the mains supply lead for signs of damage The unit must not be used if there is any damage or irregularity to the mains supply lead Use only dry and oil free com
16. ns or contact the manufacturer Caution The compressed air tank must be emptied before carrying out all service and repair work and the filter unit disconnected from the power supply and secured against being switched on again In case of leakage to the pneumatic system the filter unit must not be put into operation anymore Without compressed air supply the filter cartridge gets dirty very fast and the device switches to disturbance filter full BA_Filtercube4_091217_GB neu doc 9 17 12 2009 We set air in motion 8 Explanation of the Controls Pos 1a You can operate the control system menu by turning or pressing the joggle button Pos 1b The status control lamp illuminates for approximately seven 07 seconds when you switch on the control system and also when a low pressure vacuum builds up as a result of a flow to the filters Pos 1c The warning lamp indicates whether the filters need to be changed Pos 1d The display shows the status of the control system and any operating messages Pos 1e The unit switch switches the machine on or off The unit switch is installed up to and including a ventilator output of 4 0KW From a ventilator output of 5 5kW the ventilator must be started via a separate control e g star delta connection Pos 1f The Stroboscope flash indicates whether the filters need to be changed 9 Test run All protective equipment has to be affixed before the trial run Observe the information on the na
17. or filter cartridge Compressed air tank Compressed air connection Discharge cock for condensation Handle Cover Intermediate plate with cartridge guidance 17 12 2009 We set air in motion 2 Introduction In the last few years extractor units have gained in importance The filtering of extracted pollutants and the recycling of filtered air to the working area This is a surely a sign that the environmental consciousness of every one of us has altered very strongly in favour of our environment We have known for a long time that contaminants arise during production for example and that the type of contaminant depends on the particular industrial process used One can basically distinguish between gases and fumes smoke Fumes could also really be described as dust If you examine this dust under a microscope you will find that they consist of very fine particles often with a size of 0 001 mm or smaller that can enter the lungs The classical method of trying to improve the working conditions of polluted workplaces is general ventilation This involves changing the entire air in the production hall many times However this method has only a minimal effect on the concentration of the contaminants in the immediate area around the worker i e in the air he breathes The same applies to so called overhead extractor systems i e large extractor heads mounted above the workspace With this very unsatisfactory method the contaminants first
18. pressed air with pressure ratings from minimum 1 bar to 6 bar maximum BA_Filtercube4_091217_GB neu doc 6 17 12 2009 We set air in motion 5 Do not use the filter unit if any one or more components of the system are defective missing or damaged In any one of these instances please contact the TEKA Service Department Phone no 49 0 28 63 92 82 0 When extracting carcinogenic welding fumes as from the processing of nickel or chrome alloys the requirements of the directives on clean air of the German TRGS 560 Return of process air when working with carcinogenic media must be observed Further information regarding the TRGS 560 can be obtained from the BIA Berufsgenossenschaftliches Institut f r Arbeitssicherheit Institute for work safety of the employers liability insurances at D 53754 Sankt Augustin Germany Additional authorized protective equipment is to be used when working on the unit or collecting such as e g respiratory mask eye protectors noise protection We recommend using a respiratory mask according to DIN EN 141 143 Protection class P3 Transport Transport the machine on a pallet intended for this purpose secure against falling over and shifting Lift the machine and transport with a hand lift truck or fork lift truck Lifting trucks or fork lift trucks must have a minimum load bearing capacity of 2000 kg Do not stand below and r besides the loan when lifting and putting down Remove
19. ridges from the danger zone Caution There must be no compressed air in the compressed air tank Start the system without the work process Apply the pre coat 10g per square metre of filter surface area over the extraction point which is nearest to the filter system in the suction line Observe the manufacturer s instructions or contact the manufacturer 7 4 Connection of the compressed air supply External supply only using an authorized compressed air hose The assembly may only be carried out by qualified staff The compressed air may not be connected until the filter differential pressure value was reached which is set in the Pulsecontrol when cleaning begins see separate operating instructions of the software Remove all persons who are not required for connecting the compressed air supply from the danger zone The compressed air must be dry and oil free Connect the compressed air hose by means of a quick coupling line to the end piece nozzle Pos 17 The supplied operating pressure must have a minimum 1 bar and a maximum 6 bar and must be set dependent on the process The external compressed air supply must be designed to the extent that the compressed air tank reaches the operating pressure again within the valve idletime see operating instructions of the Pulsecontrol Software The machine must be easily accessible from all sides Observe the manufacturer s instructio
20. sing an appropriate protective respiratory mask The compressed air tank is to be emptied before carrying out all maintenance and repair work We recommend using A respiratory mask according to DIN EN 141 143 Protection class P3 The work processes specified above may only be carried out by a trained employee The filters must be disposed of according to relevant legislation and directives 14 Error search Contact manufacturer Remove all unauthorized persons from the danger zone 14 1 No function The machine or electrical system electrical line may only be checked by qualified electricians Disconnect the machine from the power supply before opening and secure against being switched on again and disconnect the machine from the external compressed air supply The compressed air tank must be emptied Suitable protection equipment such as e g respiratory mask and eye protectors must be worn when opening the filter part We recommend using a respiratory mask according to DIN EN 141 143 Protection class P3 BA_Filtercube4_091217_GB neu doc 15 17 12 2009 We set air in motion 14 2 Suction performance too low The machine or electrical system electrical line may only be checked by qualified electricians Disconnect the machine from the power supply before opening and secure against being switched on again and disconnect the machine from the external compressed air supply The compressed air tank must be empt
21. soon as the resistance of the filter cartridge has achieved a maximum value through the discharged dust particles or after a corresponding set idletime the filters are cleaned automatically Caution The filter cake is removed through the installed pneumatic cleaning which evenly distributes the compressed air over the filter surface see chapter 13 1 Cleaning of the filter cartridges The removed dust is gathered in the tank from which it can be removed see chapter 13 3 Emptying of dust collecting tank BA_Filtercube4_091217_GB neu doc 5 17 12 2009 We set air in motion 4 Safety instructions The following basic safety measures must be observed to prevent electric shocks injury or fire when using electrical devices Read and follow these instructions before you use the unit Store the operating and service instructions in a secure place Limits of application welding fumes containing oil mist aluminium dust grinding dust metallic dusts gases water not for EX zones etc If there is any doubt about the application please contact the manufacturer Do not employ the unit for the extraction of easily combustible or explosive gases and or dust mixtures Do not employ the unit in explosive zones e g zone 0 zone 1 zone 2 zone 20 zone 21 zone 22 Do not employ the unit for sucking burning or glowing materials e g cigarettes matches metallic types of dust and or splinters paper cleaning cloths oils or oil
22. t from the external compressed air supply BA_Filtercube4_091217_GB neu doc 13 17 12 2009 We set air in motion TE Open the discharge cock Pos 18 and fill the condensation into a suitable container By opening the discharge cock compressed air stored in the compressed air tank Pos 16 will escape Properly store the discharged condensation in a suitable container and dispose of according to the regulations Close the discharge cock Pos 18 Connect the compressed air tank at the external compressed air supply Connect the control for the cleaning with the power supply Observe the information on the nameplate Caution The work processes specified above may only be carried out by a correspondingly trained employee Dispose of the condensation according to the statutory regulations 13 5 Replacement of the filter cartridges When the red warning signal lamp see separate operating instructions of the software illuminates the filter cartridges must be changed as follows When replacing the cartridges the perforated plate on the intake stub must also be checked and if applicable cleaned The filter cartridges may only be replaced by qualified personnel Remove all persons who are not required for the work which is to be directly carried out from the danger zone or if applicable additionally equip with protective equipment Disconnect the machine from the power supply and secure against being switched on again D
23. tatus indicator green Pos 11 Exhaust stub Pos 1c Warning indicator red Pos 12 Toggle fastener Pos 1d Display Pos 13 Filter cartridge Pos ie Unit switch Pos 14 Cartridge bracket Pos 1f Stroboscope flash Pos 15 Locking screw for filter cartridge Pos 2 Cleaning housing Pos 16 Compressed air tank Pos 3 Service door for pneumatics Pos 17 Compressed air connection Pos 4 Filter housing Pos 18 Discharge cock for condensation Pos 5 Service door for cartridges Pos 19 Handle Pos 6 Dust collecting housing Pos 20 Cover Pos 7 Service door for tank Pos 21 Intermediate plate with cartridge guidance Pos 8 Chute Pos 22 Ventilator Pos 9 Tank BA _Filtercube4_091217_GB neu doc 3 17 12 2009 We set air in motion Filtercube 4H Pos 1a Pos 1b Pos 1c Pos 1d Pos 1e Pos 1f Pos 2 Pos 3 Pos 4 Pos 5 Pos 6 Pos 7 Pos 8 Joggle button Status indicator green Warning indicator red Display Unit switch up to and including a ventilator output of 4 0kW Stroboscope flash Cleaning housing Service door for pneumatics Filter housing Service door for cartridges Dust collecting housing Service door for tank Chute BA _Filtercube4_091217_GB neu doc Zeichnungs Nr 05363700 Pos 9 Pos 10 Pos 11 Pos 12 Pos 13 Pos 14 Pos 15 Pos 16 Pos 17 Pos 18 Pos 19 Pos 20 Pos 21 Tank Intake stub Exhaust stub Toggle fastener Filter cartridge Cartridge bracket Locking screw f

Download Pdf Manuals

image

Related Search

Related Contents

Artisan Technology Group is your source for quality new and  Moteur 1,4/55 kW  CAUTION - iTouchless  Sycologic AMI Analog to Midi Interface User Manual      1 REGLAMENTO DE VIALIDAD Y TRÁNSITO DEL  リングジョイントガスケット  4,2 MB - Institut für Umweltplanung  Advance Carpetriever™ 22, 28XP  

Copyright © All rights reserved.
Failed to retrieve file